Features • MPEG I/II-Layer 3 Hardwired Decoder • • • • • • • • • • – Stand-alone MP3 Decoder – 48, 44.1, 32, 24, 22.05, 16 kHz Sampling Frequency – Separated Digital Volume Control on Left and Right Channels (Software Control using 31 Steps) – Bass, Medium, and Treble Control (31 Steps) – Bass Boost Sound Effect – Ancillary Data Extraction – CRC Error and MPEG Frame Synchronization Indicators 20-bit Stereo Audio DAC – 93 dB SNR Playback Stereo Channel – 32 Ohm/ 20 mW Stereo Headset Drivers – Stereo Line Level Input, Differential Mono Auxiliary Input Programmable Audio Output for Interfacing with External Audio System – I2S Format Compatible Mono Audio Power Amplifier – 440mW on 8 Ohms Load USB Rev 1.1 Controller – Full Speed Data Transmission Built-in PLL – MP3 Audio Clocks – USB Clock MultiMediaCard® Interface, Secure Digital Card Interface Standard Full Duplex UART with Baud Rate Generator Power Management – Power-on Reset – Idle Mode, Power-down Mode Operating Conditions: – 2.7 to 3V, ±10%, 25 mA Typical Operating at 25°C – 37 mA Typical Operating at 25°C Playing Music on Earphone – Temperature Range: -40°C to +85°C – Power Amplifier Supply 3.2V to 5.5V Packages – CTBGA 100-pin Typical Applications • MP3-Player • PDA, Camera, Mobile Phone MP3 • Car Audio/Multimedia MP3 • Home Audio/Multimedia MP3 • Toys • Industrial Background Music / Ads Single-Chip MP3 Decoder with Full Audio Interface AT83SND2CMP3A1 AT83SND2CMP3 AT83SND2CDVX Rev. 7524D–MP3–07/07 Description The AT83SND2CMP3 has been developped as a versatile remote controlled MP3 player for very fast MP3 feature implementation into most existing system. It perfectly fits features needed in mobile phones and toys, but can also be used in any portable equipment and in industrial applications. Audio files and any other data can be stored in a Nand Flash memory or in a removable Flash card such as MultiMediaCard (MMC) or Secure Digital Card (SD). Music collections are very easy to build, as data can be stored using the standard FAT12/16 and FAT32 file system. Thanks to the USB port, data can be transferred and maintained from and to any computer based on Windows®, Linux® and Mac OS®. File system is controlled by the AT83SND2CMP3 so the host controller does not have to handle it. In addition to the USB device port, the MP3 audio system can be connected to any embedded host through a low cost serial link UART. Host controller can fully remote control the MP3 decoder behaviour using a command protocol over the serial link. File system is controlled by the AT83SND2CMP3 so host controller does not have to handle it. Files can also be uploaded or dowloaded from host environment to NAND Flash or Flash Card. 2 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Block Diagram Figure 1. Block Diagram VDD VSS UVDD UVSS 3 FILT X1 X2 Clock and PLL Unit Control Unit Interrupt Handler Unit INT0 3 INT1 RST D+ D- P0-P4 X1 USB Controller X2 I/OPorts MP3 Decoder Unit Keyboard Interface DOUT DCLK DSEL I2S/PCM Audio Interface SCLK UART and BRG Timers 0/1 Watchdog HSR HSL AUXP AUXN KIN0 3 TXD 3 RXD 3 3 T0 T1 MCLK Audio DAC SD / MMC Interface MDAT LINEL LINER MONOP MONON PAINP PAINN HPP HPN Audio PA MCMD 3 Alternate function of Port 3 4 Alternate function of Port 4 3 7524D–MP3–07/07 Pin Description Pinouts Figure 3. AT83SND2CMP3 100-pin BGA Package 10 9 8 7 6 5 4 3 2 1 NC NC P2.0/ A8 P4.1/ VDD VSS NC AUXP AUXN NC A VDD P2.2/ A10 P2.1/ A9 P4.0/ P4.2/ MONON MONOP P0.0/ AD0 KIN0 NC B P2.4/ A12 P2.3/ A11 P2.5/ A13 P4.3/ P0.6/ AD6 P0.4/ AD4 P0.3/ AD3 P0.2/ AD2 P0.1/ AD1 NC C P2.6/ A14 P2.7/ A15 MCLK NC P0.7/ AD7 P0.5/ AD5 NC NC NC NC D NC VSS VDD ESDVSS VDD SDA AUDVREF SCL HSL AUDVDD E MCMD MDAT NC P3.2/ INT0 P3.1/ TXD VSS FILT PVDD HSR HSVDD F RST AUDRST SCLK DSEL P3.4/ T0 P3.0/ RXD LINER LINEL PVSS HSVSS G NC VSS DOUT DCLK P3.5/ T1 TST X1 INGND AUDVSS H VDD AUDVSS CBP LPHN P3.7/ RD P3.6/ WR VSS D- D+ AUDVCM J PAINP PAINN HPP AUDVBAT HPN AUDVSS P3.3/ INT1 VDD UVDD UVSS X2 K 1. NC = Do Not Connect 4 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Signals All the AT83SND2CMP3 signals are detailed by functionality in following tables. Table 1. Ports Signal Description Signal Name Type Description P0.7:0 I/O Port 0 P0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high impedance inputs. To avoid any parasitic current consumption, floating P0 inputs must be polarized to VDD or VSS. P2.7:0 I/O Port 2 P2 is an 8-bit bidirectional I/O port with internal pull-ups. Alternate Function AD7:0 A15:8 RXD TXD P3.7:0 I/O Port 3 P3 is an 8-bit bidirectional I/O port with internal pull-ups. P4.3:0 I/O Port 4 P4 is an 8-bit bidirectional I/O port with internal pull-ups. INT0 INT1 T0 T1 WR RD Table 2. Clock Signal Description Signal Name Type Description Alternate Function X1 I Input to the on-chip inverting oscillator amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, its output is connected to this pin. X1 is the clock source for internal timing. X2 O Output of the on-chip inverting oscillator amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, leave X2 unconnected. - FILT I PLL Low Pass Filter input FILT receives the RC network of the PLL low pass filter. - - Table 3. Timer 0 and Timer 1 Signal Description Signal Name Type Description Alternate Function Timer 0 Gate Input INT0 serves as external run control for timer 0, when selected by GATE0 bit in TCON register. INT0 I External Interrupt 0 INT0 input sets IE0 in the TCON register. If bit IT0 in this register is set, bit IE0 is set by a falling edge on INT0#. If bit IT0 is cleared, bit IE0 is set by a low level on INT0#. P3.2 5 7524D–MP3–07/07 Signal Name Type Alternate Function Description Timer 1 Gate Input INT1 serves as external run control for timer 1, when selected by GATE1 bit in TCON register. INT1 I T0 I Timer 0 External Clock Input When timer 0 operates as a counter, a falling edge on the T0 pin increments the count. P3.4 T1 I Timer 1 External Clock Input When timer 1 operates as a counter, a falling edge on the T1 pin increments the count. P3.5 External Interrupt 1 INT1 input sets IE1 in the TCON register. If bit IT1 in this register is set, bit IE1 is set by a falling edge on INT1#. If bit IT1 is cleared, bit IE1 is set by a low level on INT1#. P3.3 Table 4. Audio Interface Signal Description Signal Name Type Alternate Function DCLK O DAC Data Bit Clock - DOUT O DAC Audio Data Output - DSEL O DAC Channel Select Signal DSEL is the sample rate clock output. - SCLK O DAC System Clock SCLK is the oversampling clock synchronized to the digital audio data (DOUT) and the channel selection signal (DSEL). - Description Table 5. USB Controller Signal Description Signal Name Type Alternate Function D+ I/O USB Positive Data Upstream Port This pin requires an external 1.5 KΩ pull-up to VDD for full speed operation. - D- I/O USB Negative Data Upstream Port - Description Table 6. MutiMediaCard Interface Signal Description 6 Signal Name Type Alternate Function MCLK O MMC Clock output Data or command clock transfer. - MCMD I/O MMC Command line Bidirectional command channel used for card initialization and data transfer commands. To avoid any parasitic current consumption, unused MCMD input must be polarized to VDD or VSS. - MDAT I/O MMC Data line Bidirectional data channel. To avoid any parasitic current consumption, unused MDAT input must be polarized to VDD or VSS. - Description AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 7. UART Signal Description Signal Name Type RXD I/O Receive Serial Data RXD sends and receives data in serial I/O mode 0 and receives data in serial I/O modes 1, 2 and 3. P3.0 TXD O Transmit Serial Data TXD outputs the shift clock in serial I/O mode 0 and transmits data in serial I/O modes 1, 2 and 3. P3.1 Description Alternate Function Table 8. Keypad Interface Signal Description Signal Name Type KIN0 I Description Keypad Input Line Holding this pin high or low for 24 oscillator periods triggers a keypad interrupt. Alternate Function - Table 9. System Signal Description Signal Name Type Description RST I Reset Input Holding this pin high for 64 oscillator periods while the oscillator is running resets the device. The Port pins are driven to their reset conditions when a voltage lower than VIL is applied, whether or not the oscillator is running. This pin has an internal pull-down resistor which allows the device to be reset by connecting a capacitor between this pin and VDD. Asserting RST when the chip is in Idle mode or Power-Down mode returns the chip to normal operation. TST I Test Input Test mode entry signal. This pin must be set to VDD. Alternate Function - - Table 10. Power Signal Description Signal Name Type Description Alternate Function VDD PWR Digital Supply Voltage Connect these pins to +3V supply voltage. - VSS GND Circuit Ground Connect these pins to ground. - PVDD PWR PLL Supply voltage Connect this pin to +3V supply voltage. - PVSS GND PLL Circuit Ground Connect this pin to ground. - UVDD PWR USB Supply Voltage Connect this pin to +3V supply voltage. - 7 7524D–MP3–07/07 Signal Name Type Description UVSS GND USB Ground Connect this pin to ground. Alternate Function - Table 11. Audio Power Signal Description Signal Name Type Description Alternate Function AUDVDD PWR Audio Digital Supply Voltage - AUDVSS GND Audio Circuit Ground Connect these pins to ground. - ESDVSS GND AUDVREF PWR Audio Voltage Reference pin for decoupling. - HSVDD PWR Headset Driver Power Supply. - HSVSS GND AUDVBAT PWR Audio Analog Circuit Ground for Electrostatic Discharge. - Connect this pin to ground. Headset Driver Ground. - Connect this pin to ground. Audio Amplifier Supply. - Table 12. Stereo Audio Dac and Mono Power Amplifier Signal Description 8 Signal Name Type LPHN O Low Power Audio Stage Output - HPN O Negative Speaker Output - HPP O Positivie Speaker Output - CBP O Audio Amplifier Common Mode Voltage Decoupling - PAINN I Audio Amplifier Negative Input - PAINP I Audio Amplifier Positive Input - AUDRST I Audio Reset (Active Low) - MONON O Audio Negative Monaural Driver Output - MONOP O Audio Positive Monaural Driver Output - AUXP I Audio Mono Auxiliary Positive Input - AUXN I Audio Mono Auxiliary Negative Input - HSL O Audio Left Channel Headset Driver Output - HSR O Audio Right Channel Headset Driver Output - LINEL I Audio Left Channel Line In - LINER I Audio Right Channel Line In - INGND I Audio Line Signal Ground Pin for decoupling. - AUDVCM I Audio Common Mode reference for decoupling - Description Alternate Function AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Internal Pin Structure Table 13. Detailed Internal Pin Structure Circuit(1) Type Pins Input TST Input/Output RST Input/Output P3 P4 Input/Output P0 MCMD MDAT RTST VDD VDD P RRST Watchdog Output VSS 2 osc periods Latch Output VDD VDD VDD P1 P2 P3 N VSS VDD P N VSS ALE SCLK DCLK VDD P Output N DOUT DSEL MCLK VSS D+ Input/Output D+ D- D- Notes: 1. For information on resistors value, input/output levels, and drive capability, refer to the DC Characteristics. 2. When the Two Wire controller is enabled, P3 transistors are disabled allowing pseudo open-drain structure. 9 7524D–MP3–07/07 Clock Controller The clock controller is based on an on-chip oscillator feeding an on-chip Phase Lock Loop (PLL). All internal clocks to the peripherals and CPU core are generated by this controller. Oscillator The X1 and X2 pins are the input and the output of a single-stage on-chip inverter (see Figure 4) that can be configured with off-chip components such as a Pierce oscillator (see Figure 5). Value of capacitors and crystal characteristics are detailed in the section “DC Characteristics”. The oscillator outputs three different clocks: a clock for the PLL, a clock for the CPU core, and a clock for the peripherals as shown in Figure 4. These clocks are either enabled or disabled, depending on the power reduction mode as detailed in the section. The peripheral clock is used to generate the Timer 0, Timer 1, MMC, SPI, and Port sampling clocks. Figure 4. Oscillator Block Diagram and Symbol X1 0 ÷2 Peripheral Clock 1 CPU Core Clock X2 X2 CKCON.0 IDL PCON.0 PD Oscillator Clock PCON.1 PER CLOCK Peripheral Clock Symbol CPU CLOCK OSC CLOCK CPU Core Clock Symbol Oscillator Clock Symbol Figure 5. Crystal Connection X1 C1 Q C2 VSS X2 PLL PLL Description The PLL is used to generate internal high frequency clock (the PLL Clock) synchronized with an external low-frequency (the Oscillator Clock). The PLL clock provides the MP3 decoder, the audio interface, and the USB interface clocks. Figure 6 shows the internal structure of the PLL. The PFLD block is the Phase Frequency Comparator and Lock Detector. This block makes the comparison between the reference clock coming from the N divider and the reverse clock coming from the R divider and generates some pulses on the Up or Down signal depending on the edge position of the reverse clock. The PLLEN bit in PLLCON register is used to enable the clock generation. The CHP block is the Charge Pump that generates the voltage reference for the VCO by injecting or extracting charges from the external filter connected on PFILT pin (see 10 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Fi gure 7) . Value of the filter components ar e detailed in the Section “ DC Characteristics”. The VCO block is the Voltage Controlled Oscillator controlled by the voltage Vref produced by the charge pump. It generates a square wave signal: the PLL clock. Figure 6. PLL Block Diagram and Symbol PFILT PLLCON.1 PLLEN N divider OSC CLOCK Up N6:0 PFLD CHP Vref VCO Down PLOCK PLL Clock R divider PLLCON.0 R9:0 PLL CLOCK OSCclk × ( R + 1 ) PLLclk = ----------------------------------------------N+1 PLL Clock Symbol Figure 7. PLL Filter Connection FILT R C2 C1 VSS PLL Programming VSS The PLL is programmed using the flow shown in Figure 8. The PLL clock frequency will depend on MP3 decoder clock and audio interface clock frequencies. Figure 8. PLL Programming Flow PLL Programming Configure Dividers N6:0 = xxxxxxb R9:0 = xxxxxxxxxxb Enable PLL PLLRES = 0 PLLEN = 1 PLL Locked? PLOCK = 1? 11 7524D–MP3–07/07 MP3 Decoder The product implements a MPEG I/II audio layer 3 decoder better known as MP3 decoder. In MPEG I (ISO 11172-3) three layers of compression have been standardized supporting three sampling frequencies: 48, 44.1, and 32 kHz. Among these layers, layer 3 allows highest compression rate of about 12:1 while still maintaining CD audio quality. For example, 3 minutes of CD audio (16-bit PCM, 44.1 kHz) data, which needs about 32M bytes of storage, can be encoded into only 2.7M bytes of MPEG I audio layer 3 data. In MPEG II (ISO 13818-3), three additional sampling frequencies: 24, 22.05, and 16 kHz are supported for low bit rates applications. The AT83SND2CMP3 can decode in real-time the MPEG I audio layer 3 encoded data into a PCM audio data, and also supports MPEG II audio layer 3 additional frequencies. Additional features are supported by the AT83SND2CMP3 MP3 decoder such as volume control, bass, medium, and treble controls, bass boost effect and ancillary data extraction. Decoder Description The core interfaces to the MP3 decoder through nine special function registers: MP3CON, the MP3 Control register; MP3STA, the MP3 Status register; MP3DAT, the MP3 Data register; MP3ANC, the Ancillary Data register; MP3VOL and MP3VOR, the MP3 Volume Left and Right Control registers; MP3BAS, MP3MED, and MP3TRE, the MP3 Bass, Medium, and Treble Control registers; and MPCLK, the MP3 Clock Divider register. Figure 9 shows the MP3 decoder block diagram. Figure 9. MP3 Decoder Block Diagram Audio Data From C51 8 1K Bytes Frame Buffer MP3DAT Header Checker Huffman Decoder MPxREQ ERRxxx MPFS1:0 MPVER MP3STA1.n MP3STA.5:3 MP3STA.2:1 MP3STA.0 Dequantizer Stereo Processor Side Information MP3 CLOCK Ancillary Buffer MP3ANC MPEN MP3CON.7 Anti-Aliasing MPBBST MP3CON.6 12 MP3VOL IMDCT MP3VOR MP3BAS Sub-band Synthesis MP3MED 16 Decoded Data To Audio Interface MP3TRE AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 MP3 Data The MP3 decoder does not start any frame decoding before having a complete frame in its input buffer(1). In order to manage the load of MP3 data in the frame buffer, a hardware handshake consisting of data request and data acknowledgment is implemented. Each time the MP3 decoder needs MP3 data, it sets the MPREQ, MPFREQ and MPBREQ flags respectively in MP3STA and MP3STA1 registers. MPREQ flag can generate an interrupt if enabled as explained in Section “Interrupt”. The CPU must then load data in the buffer by writing it through MP3DAT register thus acknowledging the previous request. As shown in Figure 10, the MPFREQ flag remains set while data (i.e a frame) is requested by the decoder. It is cleared when no more data is requested and set again when new data are requested. MPBREQ flag toggles at every Byte writing. Note: 1. The first request after enable, consists in 1024 Bytes of data to fill in the input buffer. Figure 10. Data Timing Diagram MPREQ Flag Cleared when Reading MP3STA MPFREQ Flag MPBREQ Flag Write to MP3DAT MP3 Clock The MP3 decoder clock is generated by division of the PLL clock. The division factor is given by MPCD4:0 bits in MP3CLK register. Figure 11 shows the MP3 decoder clock generator and its calculation formula. The MP3 decoder clock frequency depends only on the incoming MP3 frames. Figure 11. MP3 Clock Generator and Symbol MP3CLK PLL CLOCK MPCD4:0 MP3 CLOCK MP3 Decoder Clock MP3 Clock Symbol PLLclk MP3clk = ---------------------------MPCD + 1 As soon as the frame header has been decoded and the MPEG version extracted, the minimum MP3 input frequency must be programmed according to Table 14. Table 14. MP3 Clock Frequency MPEG Version Minimum MP3 Clock (MHz) I 21 II 10.5 13 7524D–MP3–07/07 Audio Controls Volume Control The MP3 decoder implements volume control on both right and left channels. The MP3VOR and MP3VOL registers allow a 32-step volume control according to Table 15. Table 15. Volume Control Equalization Control VOL4:0 or VOR4:0 Volume Gain (dB) 00000 Mute 00001 -33 00010 -27 11110 -1.5 11111 0 Sound can be adjusted using a 3-band equalizer: a bass band under 750 Hz, a medium band from 750 Hz to 3300 Hz and a treble band over 3300 Hz. The MP3BAS, MP3MED, and MP3TRE registers allow a 32-step gain control in each band according to Table 16. Table 16. Bass, Medium, Treble Control 14 BAS4:0 or MED4:0 or TRE4:0 Gain (dB) 00000 -∞ 00001 -14 00010 -10 11110 +1 11111 +1.5 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Frame Information The MP3 frame header contains information on the audio data contained in the frame. These informations is made available in the MP3STA register for you information. MPVER and MPFS1:0 bits allow decoding of the sampling frequency according to Table 17. MPVER bit gives the MPEG version (2 or 1). Table 17. MP3 Frame Frequency Sampling Ancillary Data MPVER MPFS1 MPFS0 Fs (kHz) 0 0 0 22.05 (MPEG II) 0 0 1 24 (MPEG II) 0 1 0 16 (MPEG II) 0 1 1 Reserved 1 0 0 44.1 (MPEG I) 1 0 1 48 (MPEG I) 1 1 0 32 (MPEG I) 1 1 1 Reserved MP3 frames also contain data bits called ancillary data. These data are made available in the MP3ANC register for each frame. As shown in Figure 12, the ancillary data are available by Bytes when MPANC flag in MP3STA register is set. MPANC flag is set when the ancillary buffer is not empty (at least one ancillary data is available) and is cleared only when there is no more ancillary data in the buffer. This flag can generate an interrupt as explained in Section “Interrupt”. When set, software must read all Bytes to empty the ancillary buffer. Figure 12. Ancillary Data Block Diagram Ancillary Data To C51 8 MP3ANC 8 7-Byte Ancillary Buffer MPANC MP3STA.7 15 7524D–MP3–07/07 Audio Output Interface The product implements an audio output interface allowing the audio bitstream to be output in various formats. It is compatible with right and left justification PCM and I2S formats and thanks to the on-chip PLL (see Section “Clock Controller”, page 10) allows connection of almost all of the commercial audio DAC families available on the market. The audio bitstream can be from 2 different types: Description • The MP3 decoded bitstream coming from the MP3 decoder for playing songs. • The audio bitstream coming from the MCU for outputting voice or sounds. The control unit core interfaces to the audio interface through five special function registers: AUDCON0 and AUDCON1, the Audio Control registers ; AUDSTA, the Audio Status register; AUDDAT, the Audio Data register; and AUDCLK, the Audio Clock Divider register. Figure 13 shows the audio interface block diagram, blocks are detailed in the following sections. Figure 13. Audio Interface Block Diagram SCLK AUD CLOCK DCLK Clock Generator 0 DSEL AUDEN 1 AUDCON1.0 Data Ready HLR DSIZ AUDCON0.0 AUDCON0.1 POL AUDCON0.2 Audio Data From MP3 Decoder 16 MP3 Buffer 16 0 16 Sample Request To MP3 Decoder DRQEN AUDCON1.6 Data Converter DOUT 1 JUST4:0 SRC AUDCON0.7:3 AUDCON1.7 SREQ Audio Data From C51 8 Audio Buffer AUDDAT AUDSTA.7 UDRN AUDSTA.6 AUBUSY DUP1:0 AUDSTA.5 AUDCON1.2:1 16 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Clock Generator The audio interface clock is generated by division of the PLL clock. The division factor is given by AUCD4:0 bits in CLKAUD register. Figure 14 shows the audio interface clock generator and its calculation formula. The audio interface clock frequency depends on the incoming MP3 frames and the audio DAC used. Figure 14. Audio Clock Generator and Symbol AUDCLK PLL CLOCK AUCD4:0 Audio Interface Clock AUD CLOCK Audio Clock Symbol PLLclk AUDclk = --------------------------AUCD + 1 As soon as audio interface is enabled by setting AUDEN bit in AUDCON1 register, the master clock generated by the PLL is output on the SCLK pin which is the DAC system clock. This clock is output at 256 or 384 times the sampling frequency depending on the DAC capabilities. HLR bit in AUDCON0 register must be set according to this rate for properly generating the audio bit clock on the DCLK pin and the word selection clock on the DSEL pin. These clocks are not generated when no data is available at the data converter input. For DAC compatibility, the bit clock frequency is programmable for outputting 16 bits or 32 bits per channel using the DSIZ bit in AUDCON0 register (see Section "Data Converter", page 17), and the word selection signal is programmable for outputting left channel on low or high level according to POL bit in AUDCON0 register as shown in Figure 15. Figure 15. DSEL Output Polarity Data Converter POL = 0 Left Channel Right Channel POL = 1 Left Channel Right Channel The data converter block converts the audio stream input from the 16-bit parallel format to a serial format. For accepting all PCM formats and I 2 S format, JUST4:0 bits in AUDCON0 register are used to shift the data output point. As shown in Figure 16, these bits allow MSB justification by setting JUST4:0 = 00000, LSB justification by setting JUST4:0 = 10000, I2S Justification by setting JUST4:0 = 00001, and more than 16-bit LSB justification by filling the low significant bits with logic 0. 17 7524D–MP3–07/07 Figure 16. Audio Output Format DSEL DCLK DOUT Left Channel 1 2 3 Right Channel 13 14 15 LSB MSB B14 16 B1 1 2 3 13 14 15 LSB MSB B14 16 B1 I2S Format with DSIZ = 0 and JUST4:0 = 00001. DSEL DCLK Left Channel 1 DOUT 2 Right Channel 3 17 MSB B14 LSB 18 32 1 2 3 17 MSB B14 LSB 18 32 I2S Format with DSIZ = 1 and JUST4:0 = 00001. DSEL DCLK DOUT Left Channel 1 2 3 Right Channel 13 14 MSB B14 15 B1 16 1 2 3 13 14 LSB MSB B15 15 B1 16 LSB MSB/LSB Justified Format with DSIZ = 0 and JUST4:0 = 00000. DSEL DCLK Left Channel 1 16 DOUT 17 Right Channel 18 31 MSB B14 B1 32 1 16 LSB 17 18 31 MSB B14 B1 32 LSB 16-bit LSB Justified Format with DSIZ = 1 and JUST4:0 = 10000. DSEL DCLK DOUT Left Channel 1 15 16 MSB B16 Right Channel 30 B2 31 B1 32 LSB 1 15 16 MSB B16 30 B2 31 B1 32 LSB 18-bit LSB Justified Format with DSIZ = 1 and JUST4:0 = 01110. The data converter receives its audio stream from 2 sources selected by the SRC bit in AUDCON1 register. When cleared, the audio stream comes from the MP3 decoder (see Section “MP3 Decoder”, page 12) for song playing. When set, the audio stream is coming from the C51 core for voice or sound playing. As soon as first audio data is input to the data converter, it enables the clock generator for generating the bit and word clocks. Audio Buffer In voice or sound playing mode, the audio stream comes from the C51 core through an audio buffer. The data is in 8-bit format and is sampled at 8 kHz. The audio buffer adapts the sample format and rate. The sample format is extended to 16 bits by filling the LSB to 00h. Rate is adapted to the DAC rate by duplicating the data using DUP1:0 bits in AUDCON1 register according to Table 18. The audio buffer interfaces to the C51 core through three flags: the sample request flag (SREQ in AUDSTA register), the under-run flag (UNDR in AUDSTA register) and the busy flag (AUBUSY in AUDSTA register). SREQ and UNDR can generate an interrupt request as explained in Section "Interrupt Request", page 19. The buffer size is 8 Bytes large. SREQ is set when the samples number switches from 4 to 3 and reset when the samples number switches from 4 to 5; UNDR is set when the buffer becomes empty signaling that the audio interface ran out of samples; and AUBUSY is set when the buffer is full. 18 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 18. Sample Duplication Factor DUP1 DUP0 Factor 0 0 No sample duplication, DAC rate = 8 kHz (C51 rate). 0 1 One sample duplication, DAC rate = 16 kHz (2 x C51 rate). 1 0 2 samples duplication, DAC rate = 32 kHz (4 x C51 rate). 1 1 Three samples duplication, DAC rate = 48 kHz (6 x C51 rate). MP3 Buffer In song playing mode, the audio stream comes from the MP3 decoder through a buffer. The MP3 buffer is used to store the decoded MP3 data and interfaces to the decoder through a 16-bit data input and data request signal. This signal asks for data when the buffer has enough space to receive new data. Data request is conditioned by the DREQEN bit in AUDCON1 register. When set, the buffer requests data to the MP3 decoder. When cleared no more data is requested but data are output until the buffer is empty. This bit can be used to suspend the audio generation (pause mode). Interrupt Request The audio interrupt request can be generated by 2 sources when in C51 audio mode: a sample request when SREQ flag in AUDSTA register is set to logic 1, and an under-run condition when UDRN flag in AUDSTA register is set to logic 1. Both sources can be enabled separately by masking one of them using the MSREQ and MUDRN bits in AUDCON1 register. A global enable of the audio interface is provided by setting the EAUD bit in IEN0 register. The interrupt is requested each time one of the 2 sources is set to one. The source flags are cleared by writing some data in the audio buffer through AUDDAT, but the global audio interrupt flag is cleared by hardware when the interrupt service routine is executed. Figure 17. Audio Interface Interrupt System UDRN AUDSTA.6 Audio Interrupt Request MUDRN AUDCON1.4 SREQ EAUD AUDSTA.7 IEN0.6 MSREQ AUDCON1.5 MP3 Song Playing In MP3 song playing mode, the operations to do are to configure the PLL and the audio interface according to the DAC selected. The audio clock is programmed to generate the 256·Fs or 384·Fs as explained in Section "Clock Generator", page 17. Figure 18 shows the configuration flow of the audio interface when in MP3 song mode. 19 7524D–MP3–07/07 Figure 18. MP3 Mode Audio Configuration Flow MP3 Mode Configuration Program Audio Clock Configure Interface HLR = X DSIZ = X POL = X JUST4:0 = XXXXXb SRC = 0 20 Enable DAC System Clock AUDEN = 1 Wait For DAC Set-up Time Enable Data Request DRQEN = 1 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 DAC and PA Interface The AT83SND2CMP3 implements a stereo Audio Digital-to-Analog Converter and Audio Power Amplifier targeted for Li-Ion or Ni-Mh battery powered devices. Figure 19. Audio Interface Block Diagram MP3 Decoder Unit DOUT DCLK DSEL I2S/PCM Audio Interface HSR HSL AUXP AUXN Audio DAC LINEL LINER MONOP MONON PAINP PAINN HPP HPN DAC Serial Audio Interface SCLK AUDCDIN AUDCDOUT AUDCCLK AUDCCS Audio PA The Stereo DAC section is a complete high performance, stereo, audio digital-to-analog converter delivering 93 dB Dynamic Range. It comprises a multibit sigma-delta modulator with dither, continuous time analog filters and analog output drive circuitry. This architecture provides a high insensitivity to clock jitter. The digital interpolation filter increases the sample rate by a factor of 8 using 3 linear phase half-band filters cascaded, followed by a first order SINC interpolator with a factor of 8. This filter eliminates the images of baseband audio, remaining only the image at 64x the input sample rate, which is eliminated by the analog post filter. Optionally, a dither signal can be added that may reduce eventual noise tones at the output. However, the use of a multibit sigmadelta modulator already provides extremely low noise tones energy. Master clock is 128 up to 512 times the input data rate allowing choice of input data rate up to 50 kHz, including standard audio rates of 48, 44.1, 32, 16 and 8 kHz. The DAC section is followed by a volume and mute control and can be simultaneously played back directly through a Stereo 32Ω Headset pair of drivers. The Stereo 32Ω Headset pair of drivers also includes a mixer of a LINEL and LINER pair of stereo inputs as well as a differential monaural auxiliary input (line level). 21 7524D–MP3–07/07 DAC Features • 20 bit D/A Conversion • 72dB Dynamic Range, -75dB THD Stereo line-in or microphone interface with 20dB • • • • • • amplification 93dB Dynamic Range, -80dB THD Stereo D/A conversion 74dB Dynamic Range / -65dB THD for 20mW output power over 32 Ohm loads Stereo, Mono and Reverse Stereo Mixer Left/Right speaker short-circuit detection flag Differential mono auxiliary input amplifier and PA driver Audio sampling rates (Fs): 16, 22.05, 24, 32, 44.1 and 48 kHz. Figure 20. Stereo DAC functional diagram PA Gain MONOP PADRV + MONON AUXP AUX AUXN AUXG Gain LINEL PGA LLIG,RLIG Gain 20,12 to -33 dB (3dB) LINER PGA Line Out Gain LLOG, RLOG 0 to -46.5dB (1.5dB) Master Playback Gain 12 to -34dB (1.5dB) Volume Control Volume Control DSEL SPKR DRV 32 HSL + DAC + Digital Filter SCLK Serial to Parallel Interface DAC_OLC Gain 6 to -6dB (3dB) SPKR DRV 32 HSR + DAC Volume Control + Volume Control Digital Filter DCLK DOUT Digital Signals Timing Data Interface To avoid noises at the output, the reset state is maintained until proper synchronism is achieved in the DAC serial interface: • DSEL • SCLK • DCLK • DOUT The data interface allows three different data transfer modes: 22 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 21. 20 bit I2S justified mode SCLK DSEL DOUT R1 R0 L(N-1) L(N-2) L(N-3) ... L2 L1 L0 R(N-1) R(N-2) R(N-3) ... R2 R1 R0 L(N-3) ... L2 L1 L0 R(N-1) R(N-2) R(N-3) ... R2 R1 R0 L(N-1) ... L1 L0 Figure 22. 20 bit MSB justified mode SCLK DSEL DOUT R0 L(N-1) L(N-2) Figure 23. 20 bit LSB justified mode SCLK DSEL DOUT R0 L(N-1) L(N-2) R(N-1) R(N-2) ... R1 R0 L(N-1) The selection between modes is done using the DINTSEL 1:0 in DAC_MISC register (Table 40.) according with the following table: DINTSEL 1:0 Format 00 I2S Justified 01 MSB Justified 1x LSB Justified The data interface always works in slave mode. This means that the DSEL and the DCLK signals are provided by microcontroller audio data interface. Serial Audio DAC Interface The serial audio DAC interface is a Synchronous Peripheral Interface (SPI) in slave mode: • AUDCDIN: is used to transfer data in series from the master to the slave DAC. It is driven by the master. • AUDCDOUT: is used to transfer data in series from the slave DAC to the master. It is driven by the selected slave DAC. • Serial Clock (AUDCCLK): it is used to synchronize the data transmission both in and out the devices through the AUDCDIN and AUDCDOUT lines. Note: Refer to Table 29. for DAC SPI Interface Description 23 7524D–MP3–07/07 Audio DAC Serial Audio Interface Figure 24. Serial Audio Interface AUDCDIN AUDCDOUT AUDCCLK AUDCCS Audio PA Protocol is as following to access DAC registers: Figure 25. Dac SPI Interface AUDCCS AUDCCLK rw a6 a5 a4 a3 a2 a1 a0 d7 d6 d5 d4 d3 d2 d1 d0 AUDCDIN AUDCDOUT DAC Interface SPI Protocol d7 d6 d5 d4 d3 d2 d1 d0 On AUDCDIN, the first bit is a read/write bit. 0 indicates a write operation while 1 is for a read operation. The 7 following bits are used for the register address and the 8 last ones are the write data. For both address and data, the most significant bit is the first one. In case of a read operation, AUDCDOUT provides the contents of the read register, MSB first. The transfer is enabled by the AUDCCS signal active low. The interface is resetted at every rising edge of AUDCCS in order to come back to an idle state, even if the transfer does not succeed. The DAC Interface SPI is synchronized with the serial clock AUDC- 24 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 CLK. Falling edge latches AUDCDIN input and rising edge shifts AUDCDOUT output bits. Note that the DLCK must run during any DAC SPI interface access (read or write). Figure 26. DAC SPI Interface Timings AUDCCS Tc Tssen Thsen Twl AUDCCLK Twh Tssdi Thsdi AUDCDIN Tdsdo Thsdo AUDCDOUT Table 19. Dac SPI Interface Timings Timing parameter Description Min Max Tc AUDCCLK min period 150 ns - Twl AUDCCLK min pulse width low 50 ns - Twh AUDCCLK min pulse width high 50 ns - Tssen Setup time AUDCCS falling to AUDCCLK rising 50 ns - Thsen Hold time AUDCCLK falling to AUDCCS rising 50 ns - Tssdi Setup time AUDCDIN valid to AUDCCLK falling 20 ns - Thsdi Hold time AUDCCLK falling to AUDCDIN not valid 20 ns - Tdsdo Delay time AUDCCLK rising to AUDCDOUT valid - 20 ns Thsdo Hold time AUDCCLK rising to AUDCDOUT not valid 0 ns - 25 7524D–MP3–07/07 DAC Register Tables DAC Gain Table 20. DAC Register Address Address Register 00h DAC_CTRL 01h Name Access Reset state Dac Control Read/Write 00h DAC_LLIG Dac Left Line in Gain Read/Write 05h 02h DAC_RLIG Dac Right Line in Gain Read/Write 05h 03h DAC_LPMG Dac Left Master Playback Gain Read/Write 08h 04h DAC_RPMG Dac Right Master Playback Gain Read/Write 08h 05h DAC_LLOG Dac Left Line Out Gain Read/Write 00h 06h DAC_RLOG Dac Right Line Out Gain Read/Write 00h 07h DAC_OLC Dac Output Level Control Read/Write 22h 08h DAC_MC Dac Mixer Control Read/Write 09h 09h DAC_CSFC Dac Clock and Sampling Frequency Control Read/Write 00h 0Ah DAC_MISC Dac Miscellaneous Read/Write 00h 0Ch DAC_PRECH Dac Precharge Control Read/Write 00h 0Dh DAC_AUXG Dac Auxilary input gain Control Read/Write 05h 10h DAC_RST Dac Reset Read/Write 00h 11h PA_CRTL Power Amplifier Control Read/Write 00h The DAC implements severals gain control: line-in (Table 21.), master playback (), lineout (Table 24.). Table 21. Line-in gain LLIG 4:0 26 RLIG 4:0 Gain (dB) 00000 20 00001 12 00010 9 00011 6 00100 3 00101 0 00110 -3 00111 -6 01000 -9 01001 -12 01010 -15 01011 -18 01100 -21 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 21. Line-in gain (Continued) 01101 -24 01110 -27 01111 -30 10000 -33 10001 < -60 Table 22. Master Playback Gain LMPG 5:0 RMPG 5:0 Gain (dB) 000000 12.0 000001 10.5 000010 9.0 000011 7.5 000100 6.0 000101 4.5 000110 3.0 000111 1.5 001000 0.0 001001 -1.5 001010 -3.0 001011 -4.5 001100 -6.0 001101 -7.5 001110 -9.0 001111 -10.5 010000 -12.0 010001 -13.5 010010 -15.0 010011 -16.5 010100 -18.0 010101 -19.5 010110 -21.0 010111 -22.5 011000 -24.0 011001 -25.5 27 7524D–MP3–07/07 Table 22. Master Playback Gain (Continued) LMPG 5:0 RMPG 5:0 Gain (dB) 011010 -27.0 011011 -28.5 011100 -30.0 011101 -31.5 011110 -33.0 011111 -34.5 100000 mute Table 23. Line-out Gain LLOG 5:0 28 RLOG 5:0 Gain (dB) 000000 0.0 000001 -1.5 000010 -3.0 000011 -4.5 000100 -6.0 000101 -7.5 000110 -9.0 000111 -10.5 001000 -12.0 001001 -13.5 001010 -15.0 001011 -16.5 001100 -18.0 001101 -19.5 001110 -21.0 001111 -22.5 010000 -24.0 010001 -25.5 010010 -27.0 010011 -28.5 010100 -30.0 010101 -31.5 010110 -33.0 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 23. Line-out Gain (Continued) 010111 -34.5 011000 -36.0 011001 -37.5 011010 -39.0 011011 -40.5 011100 -42.0 011101 -43.5 011110 -45.0 011111 -46.5 100000 mute Table 24. DAC Output Level Control LOLC 2:0 Digital Mixer Control ROLC 2:0 Gain (dB) 000 6 001 3 010 0 011 -3 100 -6 The Audio DAC features a digital mixer that allows the mixing and selection of multiple input sources. The mixing / multiplexing functions are described in the following table according with the next figure: Figure 27. Mixing / Multiplexing functions Left channel Volume Control 1 + Volume Control 2 From digital filters To DACs 1 Volume Control + 2 Volume Control Right channel Note: Whenever the two mixer inputs are selected, a –6 dB gain is applied to the output signal. Whenever only one input is selected, no gain is applied. 29 7524D–MP3–07/07 Signal Description LMSMIN1 Left Channel Mono/Stereo Mixer Left Mixed input enable – High to enable, Low to disable LMSMIN2 Left Channel Mono/Stereo Mixer Right Mixed input enable – High to enable, Low to disable RMSMIN1 Right Channel Mono/Stereo Mixer Left Mixed input enable – High to enable, Low to disable RMSMIN2 Right Channel Mono/Stereo Mixer Right Mixed input enable – High to enable, Low to disable Note: Master Clock and Sampling Frequency Selection Refer to DAC_MC register Table 38. for signal description The following table describes the different modes available for master clock and sampling frequency selection by setting OVRSEL bit in DAC_CSFC register (refer to Table 39.). Table 25. Master Clock selection OVRSEL Master Clock 0 256 x FS 1 384 x FS The selection of input sample size is done using the NBITS 1:0 in DAC_MISC register (refer to Table 40.) according to Table 26. Table 26. Input Sample Size Selection NBITS 1:0 Format 00 16 bits 01 18 bits 10 20 bits The selection between modes is done using DINTSEL 1:0 in DAC_MISC register (refer to Table 40.) according to Table 27. Table 27. Format Selection De-emphasis and dither enable DINTSEL 1:0 Format 00 I2S Justified 01 MSB Justified 1x LSB Justified The circuit features a de-emphasis filter for the playback channel. To enable the deemphasis filtering, DEEMPEN must be set to high. Likewise, the dither option (added in the playback channel) is enabled by setting the DITHEN signal to High. 30 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 28. DAC Auxlilary Input Gain AUXG 4:0 Gain (dB) 00000 20 00001 12 00010 9 00011 6 00100 3 00101 0 00110 -3 00111 -6 01000 -9 01001 -12 01010 -15 01011 -18 01100 -21 01101 -24 01110 -27 01111 -30 10000 -33 10001 <-60 31 7524D–MP3–07/07 Register Table 29. AUXCON Register AUXCON (S:90h) – Auxiliary Control Register 7 6 5 4 3 2 1 0 SDA SCL - AUDCDOUT AUDCDIN AUDCCLK AUDCCS KIN0 Bit Number Bit Mnemonic 7 SDA Description TWI Serial Data SDA is the bidirectional Two Wire data line. TWI Serial Clock When TWI controller is in master mode, SCL outputs the serial clock to the slave peripherals. When TWI controller is in slave mode, SCL receives clock from the master controller. 6 SCL 5 - 4 AUDCDOUT 3 AUDCDIN Audio Dac SPI Data Input 2 AUDCCLK Audio Dac SPI clock 1 AUDCCS Not used. Audio Dac SPI Data Output. Audio Dac Chip select Set to deselect DAC Clear to select DAC 0 KIN0 Keyboard Input Interrupt. Reset Value = 1111 1111b 32 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 30. Dac Control Register Register - DAC_CTRL (00h) 7 6 5 4 3 2 1 0 ONPADRV ONAUXIN ONDACR ONDACL ONLNOR ONLNOL ONLNIR ONLNIL Bit Bit Number Mnemonic 7 ONPADRV 6 ONAUXIN 5 ONDACR 4 ONDACL 3 ONLNOR 2 ONLNOL 1 ONLNIR 0 ONLNIL Description Differential mono PA driver Clear to power down. Set to power up. Differential mono auxiliary input amplifier Clear to power down. Set to power up. Right channel DAC Clear to power down. Set to power up. Left channel DAC Clear to power down. Set to power up. Right channel line out driver Clear to power down. Set to power up. Left channel line out driver Clear to power down. Set to power up. Right channel line in amplifier Clear to power down. Set to power up. Left channel line in amplifier Clear to power down. Set to power up. Reset Value = 00000000b Table 31. DAC Left Line In Gain Register - DAC_LLIG (01h) 7 6 5 4 3 2 1 0 - - - LLIG4 LLIG3 LLIG2 LLIG1 LLIG0 Bit Bit Number Mnemonic 7:5 - 4:0 LLIG 4:0 Description Not used Left channel line in analog gain selector Reset Value = 00000101b 33 7524D–MP3–07/07 Table 32. DAC Right Line In Gain Register - DAC_RLIG (02h) 7 6 5 4 3 2 1 0 - - - RLIG4 RLIG3 RLIG2 RLIG1 RLIG0 Bit Number Description Bit Mnemonic 7:5 - Not used 4:0 RLIG 4:0 Right channel line in analog gain selector Reset Value = 0000101b Table 33. DAC Left Master Playback Gain Register - DAC_LMPG (03h) 7 6 5 4 3 2 1 0 - - LMPG5 LMPG4 LMPG3 LMPG2 LMPG1 LMPG0 Bit Number Bit Mnemonic 7:6 - 5:0 LMPG 5:0 Description Not used Left channel master playback digital gain selector Reset Value = 00001000b Table 34. DAC Right Master Playback Gain Register - DAC_RMPG (04h) 7 6 5 4 3 2 1 0 - - RMPG5 RMPG4 RMPG3 RMPG2 RMPG1 RMPG0 Bit Number Description Bit Mnemonic 7:6 - Not used 5:0 RMPG 5:0 Right channel master playback digital gain selector Reset Value = 00001000b Table 35. DAC Left Line Out Gain Register - DAC_LLOG (05h) 7 6 5 4 3 2 1 0 - - LLOG5 LLOG4 LLOG3 LLOG2 LLOG1 LLOG0 Bit Number Bit Mnemonic 7:6 - 5:0 LLOG 5:0 Description Not used Left channel line out digital gain selector Reset Value = 00000000b 34 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 36. DAC Rigth Line Out Gain Register - DAC_RLOG (06h) 7 6 5 4 3 2 1 0 - - RLOG5 RLOG4 RLOG3 RLOG2 RLOG1 RLOG0 Bit Number Description Bit Mnemonic 7:6 - 5:0 Not used RLOG 5:0 Right channel line out digital gain selector Reset Value = 00000000b Table 37. DAC Output Level Control Register - DAC_OLC (07h) 7 6 5 4 3 2 1 0 RSHORT ROLC2 RLOC1 RLOC0 LSHORT LOLC2 LOLC1 LOLC0 Bit Number Bit Mnemonic 7 RSHORT Description Right channel short circuit indicator (persistent; after being set, bit is not cleared automatically even after the short circuit is eliminated; must be cleared by reset cycle or direct register write operation) 6:4 ROLC 2:0 3 LSHORT Right channel output level control selector Left channel short circuit indicator (persistent; after being set, bit is not cleared automatically even after the short circuit is eliminated; must be cleared by reset cycle or direct register write operation) 2:0 LOLC 2:0 Left channel output level control selector Reset Value = 00100010b 35 7524D–MP3–07/07 Table 38. Dac Mixer Control Register - DAC_MC (08h) 7 6 5 4 3 2 1 0 - - INVR INVL RMSMIN2 RMSMIN1 LMSMIN2 LMSMIN1 Bit Bit Mnemonic Number 7:6 - 5 INVR 4 INVL 3 RMSMIN2 2 RMSMIN1 1 LMSMIN2 0 LMSMIN1 Description Not used Right channel mixer output invert Set to enable. Clear to disable. Left channel mixer output invert. Set to enable. Clear to disable. Right Channel Mono/Stereo Mixer Right Mixed input enable Set to enable. Clear to disable. Right Channel Mono/Stereo Mixer Left Mixed input enable Set to enable. Clear to disable. Left Channel Mono/Stereo Mixer Right Mixed input enable Set to enable. Clear to disable. Left Channel Mono/Stereo Mixer Left Mixed input enable Set to enable. Clear to disable. Reset Value = 00001001b Table 39. DAC Mixer Control Register - DAC_CSFC (09h) 7 6 5 4 3 2 1 0 - - - OVRSEL - - - - Bit Number Bit Mnemonic 7:5 - 4 OVRSEL Description Not used Master clock selector Clear for 256 x Fs. Set for 384 x Fs. 3:0 - Not Used Reset Value = 00000000b 36 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 40. Dac Miscellaneous Register - DAC_ MISC (0Ah) 7 6 5 4 3 2 1 0 - - DINTSEL1 DINTSEL0 DITHEN DEEMPEN NBITS1 NBITS0 Bit Bit Mnemonic Number Description 7 - Not used 6 - Not used DINTSEL1:0 I2S data format selector 3 DITHEN Dither enable (Clear this bit to disable, set to enable) 2 DEEMPEN De-emphasis enable (clear this bit to disable, set to enable) 1:0 NBITS 1:0 Data interface word length 5:4 Reset Value = 00000010b Table 41. DAC Precharge Control Register - DAC_ PRECH (0Ch) 7 6 5 4 3 2 1 0 PRCHAR GEPADRV PRCHAR GEAUXIN PRCHAR GELNOR PRCHAR GELNOL PRCHAR GELNIL PRCHAR GELNIL PRCHAR GE ONMSTR Bit Bit Number Mnemonic Description 7 PRCHARGEPAD Differential mono PA driver pre-charge. RV Set to charge. 6 PRCHARGEAUX Differential mono auxiliary input pre-charge. IN Set to charge. 5 PRCHARGELNO Right channel line out pre-charge. R Set to charge. 4 PRCHARGELNO Left channel line out pre-charge. L Set to charge. 3 PRCHARGELNI R 2 PRCHARGELNIL 1 PRCHARGE 0 ONMSTR Right channel line in pre-charge. Set to charge. Left channel line in pre-charge Set to charge. Master pre-charge Set to charge. Master power on control Clear to power down. Set to to power up. Reset Value = 00000000b 37 7524D–MP3–07/07 Table 42. DAC Auxilary input gain Register - DAC_ AUXG (0Dh)l 7 6 5 4 3 2 1 0 - - - AUXG4 AUXG3 AUXG2 AUXG1 AUXG0 Bit Number Bit Mnemonic 7:5 - 4:0 AUXG 4:0 Description Not used Differential mono auxiliary input analog gain selector Reset Value = 0000101b DAC Reset Register - DAC_ RST (10h) 7 6 5 4 3 2 1 0 - - - - - RESMASK RESFILZ RSTZ Bit Number Bit Mnemonic 7:3 - 2 RESMASK 1 RESFILZ 0 RSTZ Description Not Used. Active high reset mask of the audio codec Active low reset of the audio codec filter Active low reset of the audio codec Reset Value = 00000000b Note: 38 Refer to Audio DAC Startup sequence. AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Power Amplifier High quality mono output is provided. The DAC output is connected through a buffer stage to the input of the Audio Power Amplifier, using two coupling capacitors The mono buffer stage also includes a mixer of the LINEL and LINER inputs as well as a differential monaural auxiliary input (line level) which can be, for example, the output of a voice CODEC output driver in mobile phones. In the full power mode, the Power Amplifier is capable of driving an 8Ω Loudspeaker at maximum power of 440mW, making it suitable as a handsfree speaker driver in Wireless Handset Application. The Low Power Mode is designed to be switched from the handsfree mode to the normal earphone/speaker mode of a telephone handset. The audio power amplifier is not internally protected against short-circuit. The user should avoid any short-circuit on the load. PA Features • • • • 0.44W on 8Ω Load Low Power Mode for Earphone Programmable Gain (-22 to +20 dB) Fully Differential Structure, Input and Output Table 43. PA Gain APAGAIN 3:0 Gain (db) 0000 -22 0001 20 0010 17 0011 14 0100 11 0101 8 0110 5 0111 2 1000 -1 1001 -4 1010 -7 1011 -10 1100 -13 1101 -16 1110 -19 1111 -22 39 7524D–MP3–07/07 Table 44. PA Operating Mode APAON APAPRECH Operating Mode 0 0 Stand-By 0 1 Input Capacitors Precharge 1 0 Active Mode 1 1 Forbidden State Table 45. PA Low Power Mode APALP Audio Supplies and Start-up Power Mode 0 Low power mode 1 High power mode In operating mode AUDVBAT (supply of the audio power amplifier) must be between 3V and 5,5V. AUDVDD, HSVDD and VDD must be inferior or equal to AUDVBAT. A typical application is AUDVBAT connected to a battery and AUDVDD, HSVDD and VDD supplied by regulators. AUDVBAT must be present at the same time or before AUDVDD, HSVDD and VDD. AUDRST must be active low (0) until the voltages are not etablished and reach the proper values. To avoid noise issues, it is recommended to use ceramic decoupling capacitors for each supply closed to the package. The track of the supplies must be optimized to minimize the resistance especially on AUDVBAT where all the current from the power amplifier comes from. Note: Refer to the application diagram. Audio DAC Start-up Sequence In order to minimize any audio output noise during the start-up, the following sequence should be applied. Example of power-on: Path DAC to Headset Output Example of power-off: Path DAC to Headset Output 40 • Desassert the Reset: write 07h at address 10h. • All precharge and Master on: write FFh at address 0Ch. • Line Out On: write 30h at address 00h. • Delay 500 ms. • Precharge off: write 0Ch at address 01h. • Delay 1 ms. • Line Out on, DAC On: write 3Ch at address 00h. • DAC off: write 30h at address 00h. • Master off: write 00h at address 0Ch. • Delay 1 ms. • All off: write 00h at address 00h AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Example Start I2S Example Stop I2S: • Start DCLK. • RSTMASK=1. • RESFILZ=0 and RSTZ=0. • RESFILZ=1 and RSTZ=1. • RSTMASK=0. • Delay 5 ms. • ONDACL=1 and ONDACR=1. • Program all DAC settings: audio format, gains... • DAC off: ONDACL=0 and ONDACR=0. • Stop I2S and DLCK. Audio PA Sequence PA Power-On Sequence To avoid an audible ‘click’ at start-up, the input capacitors have to be pre-charged before the Power Amplifier. PA Power-Off Sequence To avoid an audible ‘click’ at power-off, the gain should be set to the minimum gain (22dB) before setting the Power Amplifier. Precharge Control The power up of the circuit can be performed independently for several blocks. The sequence flow starts by setting to High the block specific fastcharge control bit and subsequently the associated power control bit. Once the power control bit is set to High, the fast charging starts. This action begins a user controlled fastcharge cycle. When the fastcharge period is over, the user must reset the associated fastcharge bit and the block is ready for use. If a power control bit is cleared a new power up sequence is needed. The several blocks with independent power control are identified in Table 46. The table describes the power on control and fastcharge bits for each block. Table 46. Precharge and Power Control Powered up block Power on control bit Vref & Vcm generator ONMSTR Left line in amplifier ONLNIL PRCHARGELNIL Right line in amplifier ONLNIR PRCHARGELNIR Left line out amplifier ONLNOL PRCHARGELNOL Right line out amplifier ONLNOR PRCHARGELNOR Left D-to-A converter ONDACL Not needed Right D-to-A converter ONDACR Not needed Auxiliary input amplifier ONAUXIN PRCHARGEAUXIN PA Driver output ONPADRV PRCHARGEPADRV Note: Precharge Control Bit PRCHARGE (reg 12; bit 1) Note that all block can be precharged simultaneously. 41 7524D–MP3–07/07 Register Table 47. PA Control Register - PA_CTRL (11h)l 7 6 5 4 3 2 1 0 - APAON APAPREC H APALP APAGAIN3 APAGAIN2 APAGAIN1 APAGAIN0 Bit Number Bit Mnemonic Description 7 - 6 APAON 5 APAPRECH Audio power amplifier precharge bit 4 APALP Audio power amplifier low power bit 3:0 APAGAIN3:0 Not used Audio power amplifier on bit Audio power amplifier gain Reset Value = 00000000b 42 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Universal Serial Bus The product implements a USB device controller supporting full speed data transfer. In addition to the default control endpoint 0, it provides 2 other endpoints, which can be configured in control, bulk, interrupt or isochronous modes: • Endpoint 0: 32-Byte FIFO, default control endpoint • Endpoint 1, 2: 64-Byte Ping-pong FIFO, This allows the firmware to be developed conforming to most USB device classes, for example: USB Mass Storage Class Bulk-Only Transport • USB Mass Storage Class Bulk-only Transport, Revision 1.0 - September 31, 1999 • USB Human Interface Device Class, Version 1.1 - April 7, 1999 • USB Device Firmware Upgrade Class, Revision 1.0 - May 13, 1999 Within the Bulk-only framework, the Control endpoint is only used to transport classspecific and standard USB requests for device set-up and configuration. One Bulk-out endpoint is used to transport commands and data from the host to the device. One Bulk in endpoint is used to transport status and data from the device to the host. The following AT83SND2CMP3 configuration adheres to those requirements: USB Device Firmware Upgrade (DFU) • Endpoint 0: 32 Bytes, Control In-Out • Endpoint 1: 64 Bytes, Bulk-in • Endpoint 2: 64 Bytes, Bulk-out The USB Device Firmware Update (DFU) protocol can be used to upgrade the on-chip Flash memory of the AT83SND2CMP3. This allows installing product enhancements and patches to devices that are already in the field. 2 different configurations and descriptor sets are used to support DFU functions. The Run-Time configuration co-exist with the usual functions of the device, which is USB Mass Storage for AT83SND2CMP3. It is used to initiate DFU from the normal operating mode. The DFU configuration is used to perform the firmware update after device re-configuration and USB reset. It excludes any other function. Only the default control pipe (endpoint 0) is used to support DFU services in both configurations. The only possible value for the MaxPacketSize in the DFU configuration is 32 Bytes, which is the size of the FIFO implemented for endpoint 0. 43 7524D–MP3–07/07 Description The USB device controller provides the hardware that the AT83SND2CMP3 needs to interface a USB link to a data flow stored in a double port memory. It requires a 48 MHz reference clock provided by the clock controller as detailed in Section "", page 44. This clock is used to generate a 12 MHz Full Speed bit clock from the received USB differential data flow and to transmit data according to full speed USB device tolerance. Clock recovery is done by a Digital Phase Locked Loop (DPLL) block. The Serial Interface Engine (SIE) block performs NRZI encoding and decoding, bit stuffing, CRC generation and checking, and the serial-parallel data conversion. The Universal Function Interface (UFI) controls the interface between the data flow and the Dual Port RAM, but also the interface with the C51 core itself. Figure 30 shows how to connect the AT83SND2CMP3 to the USB connector. D+ and Dpins are connected through 2 termination resistors. Value of these resistors is detailed in the section “DC Characteristics”. Figure 28. USB Device Controller Block Diagram USB CLOCK D+ D- 48 MHz 12 MHz DPLL USB Buffer UFI To/From C51 Core SIE Figure 29. USB Connection VBUS To Power Supply D+ RUSB D+ D- RUSB D- GND VSS 44 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Clock Controller The USB controller clock is generated by division of the PLL clock. The division factor is given by USBCD1:0 bits in USBCLK register. Figure 30 shows the USB controller clock generator and its calculation formula. The USB controller clock frequency must always be 48 MHz. Figure 30. USB Clock Generator and Symbol USBCLK PLL CLOCK USBCD1:0 48 MHz USB Clock PLLclk USBclk = -------------------------------USBCD + 1 USB CLOCK USB Clock Symbol 45 7524D–MP3–07/07 Serial Interface Engine (SIE) The SIE performs the following functions: • NRZI data encoding and decoding. • Bit stuffing and unstuffing. • CRC generation and checking. • ACKs and NACKs automatic generation. • TOKEN type identifying. • Address checking. • Clock recovery (using DPLL). Figure 31. SIE Block Diagram End of Packet Detector SYNC Detector Start of Packet Detector NRZI ‘ NRZ Bit Unstuffing Packet Bit Counter Address Decoder Serial to Parallel Converter D+ DUSB 48 MHz CLOCK Clock Recover PID Decoder 8 Data Out SysClk (12 MHz) CRC5 & CRC16 Generator/Check USB Pattern Generator Parallel to Serial Converter Bit Stuffing NRZI Converter CRC16 Generator 46 8 Data In AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Function Interface Unit (UFI) The Function Interface Unit provides the interface between the AT83SND2CMP3 and the SIE. It manages transactions at the packet level with minimal intervention from the device firmware, which reads and writes the endpoint FIFOs. Figure 33 shows typical USB IN and OUT transactions reporting the split in the hardware (UFI) and software (C51) load. Figure 32. UFI Block Diagram 12 MHz DPLL Transfer Control FSM To/From SIE Endpoint Control USB side Asynchronous Information Endpoint 2 USBCON USBADDR USBINT USBIEN UEPNUM UEPCONX UEPSTAX UEPRST UEPINT UEPIEN UEPDATX UBYCTX UFNUMH UFNUML To/From C51 Core Endpoint Control C51 side Endpoint 1 Endpoint 0 Figure 33. USB Typical Transaction Load OUT Transactions: HOST OUT DATA0 (n Bytes) UFI C51 OUT ACK DATA1 C51 interrupt OUT DATA1 NACK ACK Endpoint FIFO read (n Bytes) IN Transactions: HOST UFI C51 IN IN NACK Endpoint FIFO Write IN DATA1 ACK DATA1 C51 interrupt Endpoint FIFO write 47 7524D–MP3–07/07 Upstream Resume A USB device can be allowed by the Host to send an upstream resume for Remote Wake-up purpose. When the USB controller receives the SET_FEATURE request: DEVICE_REMOTE_WAKEUP, the firmware should set to 1 the RMWUPE bit in the USBCON register to enable this functionality. RMWUPE value should be 0 in the other cases. If the device is in SUSPEND mode, the USB controller can send an upstream resume by clearing first the SPINT bit in the USBINT register and by setting then to 1 the SDRMWUP bit in the USBCON register. The USB controller sets to 1 the UPRSM bit in the USBCON register. All clocks must be enabled first. The Remote Wake is sent only if the USB bus was in Suspend state for at least 5ms. When the upstream resume is completed, the UPRSM bit is reset to 0 by hardware. The firmware should then clear the SDRMWUP bit. Figure 34. Example of REMOTE WAKEUP Management USB Controller Init SET_FEATURE: DEVICE_REMOTE_WAKEUP Set RMWUPE SPINT Detection of a SUSPEND state Suspend Management need USB resume enable clocks Clear SPINT UPRSM = 1 Set SDMWUP UPRSM upstream RESUME sent Clear SDRMWUP 48 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 USB Interrupt System Interrupt System Priorities D+ D- Figure 35. USB Interrupt Control System 00 01 10 11 USB Controller EUSB EA IE1.6 IE0.7 IPH/L Priority Enable Interrupt Enable Lowest Priority Interrupts Table 1. Priority Levels USB Interrupt Control System IPHUSB IPLUSB USB Priority Level 0 0 0..................Lowest 0 1 1 1 0 2 1 1 3..................Highest As shown in Figure 36, many events can produce a USB interrupt: • TXCMPL: Transmitted In Data. This bit is set by hardware when the Host accept a In packet. • RXOUTB0: Received Out Data Bank 0. This bit is set by hardware when an Out packet is accepted by the endpoint and stored in bank 0. • RXOUTB1: Received Out Data Bank 1 (only for Ping-pong endpoints). This bit is set by hardware when an Out packet is accepted by the endpoint and stored in bank 1. • RXSETUP: Received Setup. This bit is set by hardware when an SETUP packet is accepted by the endpoint. • STLCRC: STALLED (only for Control, Bulk and Interrupt endpoints). This bit is set by hardware when a STALL handshake has been sent as requested by STALLRQ, and is reset by hardware when a SETUP packet is received. • SOFINT: Start of Frame Interrupt . This bit is set by hardware when a USB start of frame packet has been received. • WUPCPU: Wake-Up CPU Interrupt. This bit is set by hardware when a USB resume is detected on the USB bus, after a SUSPEND state. • SPINT: Suspend Interrupt. This bit is set by hardware when a USB suspend is detected on the USB bus. 49 7524D–MP3–07/07 Figure 36. USB Interrupt Control Block Diagram Endpoint X (X = 0..2) TXCMP UEPSTAX.0 RXOUTB0 UEPSTAX.1 RXOUTB1 EPXINT UEPSTAX.6 UEPINT.X RXSETUP EPXIE UEPSTAX.2 UEPIEN.X STLCRC UEPSTAX.3 NAKOUT UEPCONX.5 NAKIN UEPCONX.4 NAKIEN UEPCONX.6 WUPCPU EUSB USBINT.5 EWUPCPU IE1.6 USBIEN.5 EORINT USBINT.4 EEORINT USBIEN.4 SOFINT USBINT.3 ESOFINT USBIEN.3 SPINT USBINT.0 ESPINT USBIEN.0 50 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 MultiMedia Card Controller The AT83SND2CMP3 implements a MultiMedia Card (MMC) controller. The MMC is used to store MP3 encoded audio files in removable Flash memory cards that can be easily plugged or removed from the application. Card Concept The basic MultiMedia Card concept is based on transferring data via a minimum number of signals. Card Signals The communication signals are: Card Registers • CLK: with each cycle of this signal a one bit transfer on the command and data lines is done. The frequency may vary from zero to the maximum clock frequency. • CMD: is a bi-directional command channel used for card initialization and data transfer commands. The CMD signal has 2 operation modes: open-drain for initialization mode and push-pull for fast command transfer. Commands are sent from the MultiMedia Card bus master to the card and responses from the cards to the host. • DAT: is a bi-directional data channel. The DAT signal operates in push-pull mode. Only one card or the host is driving this signal at a time. Within the card interface five registers are defined: OCR, CID, CSD, RCA and DSR. These can be accessed only by the corresponding commands. The 32-bit Operation Conditions Register (OCR) stores the VDD voltage profile of the card. The register is optional and can be read only. The 128-bit wide CID register carries the card identification information (Card ID) used during the card identification procedure. The 128-bit wide Card-Specific Data register (CSD) provides information on how to access the card contents. The CSD defines the data format, error correction type, maximum data access time, data transfer speed, and whether the DSR register can be used. The 16-bit Relative Card Address register (RCA) carries the card address assigned by the host during the card identification. This address is used for the addressed host-card communication after the card identification procedure. The 16-bit Driver Stage Register (DSR) can be optionally used to improve the bus performance for extended operating conditions (depending on parameters like bus length, transfer rate or number of cards). Bus Concept The MultiMedia Card bus is designed to connect either solid-state mass-storage memory or I/O-devices in a card format to multimedia applications. The bus implementation allows the coverage of application fields from low-cost systems to systems with a fast data transfer rate. It is a single master bus with a variable number of slaves. The MultiMedia Card bus master is the bus controller and each slave is either a single mass storage card (with possibly different technologies such as ROM, OTP, Flash etc.) or an I/O-card with its own controlling unit (on card) to perform the data transfer. The MultiMedia Card bus also includes power connections to supply the cards. The bus communication uses a special protocol (MultiMedia Card bus protocol) which is applicable for all devices. Therefore, the payload data transfer between the host and the cards can be bi-directional. 51 7524D–MP3–07/07 Bus Lines The MultiMedia Card bus architecture requires all cards to be connected to the same set of lines. No card has an individual connection to the host or other devices, which reduces the connection costs of the MultiMedia Card system. The bus lines can be divided into three groups: Bus Protocol • Power supply: VSS1 and VSS2, VDD – used to supply the cards. • Data transfer: MCMD, MDAT – used for bi-directional communication. • Clock: MCLK – used to synchronize data transfer across the bus. After a power-on reset, the host must initialize the cards by a special message-based MultiMedia Card bus protocol. Each message is represented by one of the following tokens: • Command: a command is a token which starts an operation. A command is transferred serially from the host to the card on the MCMD line. • Response: a response is a token which is sent from an addressed card (or all connected cards) to the host as an answer to a previously received command. It is transferred serially on the MCMD line. • Data: data can be transferred from the card to the host or vice-versa. Data is transferred serially on the MDAT line. Card addressing is implemented using a session address assigned during the initialization phase, by the bus controller to all currently connected cards. Individual cards are identified by their CID number. This method requires that every card will have an unique CID number. To ensure uniqueness of CIDs the CID register contains 24 bits (MID and OID fields) which are defined by the MMCA. Every card manufacturers is required to apply for an unique MID (and optionally OID) number. MultiMedia Card bus data transfers are composed of these tokens. One data transfer is a bus operation. There are different types of operations. Addressed operations always contain a command and a response token. In addition, some operations have a data token, the others transfer their information directly within the command or response structure. In this case no data token is present in an operation. The bits on the MDAT and the MCMD lines are transferred synchronous to the host clock. 2 types of data transfer commands are defined: • Sequential commands: These commands initiate a continuous data stream, they are terminated only when a stop command follows on the MCMD line. This mode reduces the command overhead to an absolute minimum. • Block-oriented commands: These commands send a data block succeeded by CRC bits. Both read and write operations allow either single or multiple block transmission. A multiple block transmission is terminated when a stop command follows on the MCMD line similarly to the stream read. Figure 37 through Figure 41 show the different types of operations, on these figures, grayed tokens are from host to card(s) while white tokens are from card(s) to host. Figure 37. Sequential Read Operation Stop Command MCMD Command Response MDAT Response Data Stream Data Transfer Operation 52 Command Data Stop Operation AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 38. (Multiple) Block Read Operation Stop Command MCMD Command Response MDAT Command Response Data Block CRC Data Block CRC Data Block CRC Block Read Operation Data Stop Operation Multiple Block Read Operation As shown in Figure 39 and Figure 40 the data write operation uses a simple busy signalling of the write operation duration on the data line (MDAT). Figure 39. Sequential Write Operation Stop Command MCMD Command Response Command MDAT Data Stream Response Busy Data Transfer Operation Data Stop Operation Figure 40. Multiple Block Write Operation Stop Command MCMD Command Response MDAT Command Data Block CRC Status Busy Response Data Block CRC Status Busy Block Write Operation Data Stop Operation Multiple Block Write Operation Figure 41. No Response and No Data Operation MCMD Command Command Response MDAT No Response Operation Command Token Format No Data Operation As shown in Figure 42, commands have a fixed code length of 48 bits. Each command token is preceded by a Start bit: a low level on MCMD line and succeeded by an End bit: a high level on MCMD line. The command content is preceded by a Transmission bit: a high level on MCMD line for a command token (host to card) and succeeded by a 7 - bit CRC so that transmission errors can be detected and the operation may be repeated. Command content contains the command index and address information or parameters. Figure 42. Command Token Format 0 1 Content CRC 1 Total Length = 48 bits 53 7524D–MP3–07/07 Table 48. Command Token Format Bit Position 47 46 45:40 39:8 7:1 0 Width (Bits) 1 1 6 32 7 1 Value ‘0’ ‘1’ - - - ‘1’ Start bit Transmission bit Command Index Argument CRC7 End bit Description Response Token Format There are five types of response tokens (R1 to R5). As shown in Figure 43, responses have a code length of 48 bits or 136 bits. A response token is preceded by a Start bit: a low level on MCMD line and succeeded by an End bit: a high level on MCMD line. The command content is preceded by a Transmission bit: a low level on MCMD line for a response token (card to host) and succeeded (R1,R2,R4,R5) or not (R3) by a 7 - bit CRC. Response content contains mirrored command and status information (R1 response), CID register or CSD register (R2 response), OCR register (R3 response), or RCA register (R4 and R5 response). Figure 43. Response Token Format R1, R4, R5 0 0 Content CRC 1 Total Length = 48 bits R3 0 0 Content 1 Total Length = 48 bits R2 0 0 Content = CID or CSD CRC 1 Total Length = 136 bits Table 49. R1 Response Format (Normal Response) Bit Position 47 46 45:40 39:8 7:1 0 Width (bits) 1 1 6 32 7 1 Value ‘0’ ‘0’ - - - ‘1’ Start bit Transmission bit Command Index Card Status CRC7 End bit Description Table 50. R2 Response Format (CID and CSD registers) Bit Position 135 134 [133:128] [127:1] 0 Width (bits) 1 1 6 32 1 Value ‘0’ ‘0’ ‘111111’ - ‘1’ Start bit Transmission bit Reserved Argument End bit Description 54 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Table 51. R3 Response Format (OCR Register) Bit Position 47 46 [45:40] [39:8] [7:1] 0 Width (bits) 1 1 6 32 7 1 Value ‘0’ ‘0’ ‘111111’ - ‘1111111’ ‘1’ Start bit Transmission bit Reserved OCR register Reserved End bit Description Table 52. R4 Response Format (Fast I/O) Bit Position 47 46 [45:40] [39:8] [7:1] 0 Width (bits) 1 1 6 32 7 1 Value ‘0’ ‘0’ ‘100111’ - - ‘1’ Start bit Transmission bit Command Index Argument CRC7 End bit Description Table 53. R5 Response Format Bit Position 47 46 [45:40] [39:8] [7:1] 0 Width (bits) 1 1 6 32 7 1 Value ‘0’ ‘0’ ‘101000’ - - ‘1’ Start bit Transmission bit Command Index Argument CRC7 End bit Description Data Packet Format There are 2 types of data packets: stream and block. As shown in Figure 44, stream data packets have an indeterminate length while block packets have a fixed length depending on the block length. Each data packet is preceded by a Start bit: a low level on MCMD line and succeeded by an End bit: a high level on MCMD line. Due to the fact that there is no predefined end in stream packets, CRC protection is not included in this case. The CRC protection algorithm for block data is a 16-bit CCITT polynomial. Figure 44. Data Token Format Sequential Data 0 Block Data 0 Content Content 1 CRC 1 Block Length Clock Control The MMC bus clock signal can be used by the host to turn the cards into energy saving mode or to control the data flow (to avoid under-run or over-run conditions) on the bus. The host is allowed to lower the clock frequency or shut it down. There are a few restrictions the host must follow: • The bus frequency can be changed at any time (under the restrictions of maximum data transfer frequency, defined by the cards, and the identification frequency defined by the specification document). • It is an obvious requirement that the clock must be running for the card to output data or response tokens. After the last MultiMedia Card bus transaction, the host is 55 7524D–MP3–07/07 required, to provide 8 (eight) clock cycles for the card to complete the operation before shutting down the clock. Following is a list of the various bus transactions: Description • A command with no response. 8 clocks after the host command End bit. • A command with response. 8 clocks after the card command End bit. • A read data transaction. 8 clocks after the End bit of the last data block. • A write data transaction. 8 clocks after the CRC status token. • The host is allowed to shut down the clock of a “busy” card. The card will complete the programming operation regardless of the host clock. However, the host must provide a clock edge for the card to turn off its busy signal. Without a clock edge the card (unless previously disconnected by a deselect command-CMD7) will force the MDAT line down, forever. The MMC controller interfaces to the C51 core through the following eight special function registers: MMCON0, MMCON1, MMCON2, the three MMC control registers; MMSTA, the MMC status register ; MMINT, the MMC interrupt register; MMMSK, the MMC interrupt mask register; MMCMD, the MMC command register; MMDAT, the MMC data register; and MMCLK, the MMC clock register. As shown in Figure 45, the MMC controller is divided in four blocks: the clock generator that handles the MCLK (formally the MMC CLK) output to the card, the command line controller that handles the MCMD (formally the MMC CMD) line traffic to or from the card, the data line controller that handles the MDAT (formally the MMC DAT) line traffic to or from the card, and the interrupt controller that handles the MMC controller interrupt sources. These blocks are detailed in the following sections. Figure 45. MMC Controller Block Diagram MCLK OSC CLOCK Clock Generator Command Line Controller MCMD Interrupt Controller Internal Bus Clock Generator 56 Data Line Controller 8 MMC Interrupt Request MDAT The MMC clock is generated by division of the oscillator clock (FOSC) issued from the Clock Controller block as detailed in Section "Oscillator", page 10. The division factor is given by MMCD7:0 bits in MMCLK register, a value of 0x00 stops the MMC clock. Figure 46 shows the MMC clock generator and its output clock calculation formula. AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 46. MMC Clock Generator and Symbol OSC CLOCK Controller Clock OSCclk MMCclk = ----------------------------MMCD + 1 MMCLK MMCEN MMCON2.7 MMCD7:0 MMC Clock MMC CLOCK MMC Clock Symbol As soon as MMCEN bit in MMCON2 is set, the MMC controller receives its system clock. The MMC command and data clock is generated on MCLK output and sent to the command line and data line controllers. Figure 47 shows the MMC controller configuration flow. As exposed in Section “Clock Control”, page 55, MMCD7:0 bits can be used to dynamically increase or reduce the MMC clock. Figure 47. Configuration Flow MMC Controller Configuration Configure MMC Clock MMCLK = XXh MMCEN = 1 FLOWC = 0 57 7524D–MP3–07/07 Command Line Controller As shown in Figure 48, the command line controller is divided in 2 channels: the command transmitter channel that handles the command transmission to the card through the MCMD line and the command receiver channel that handles the response reception from the card through the MCMD line. These channels are detailed in the following sections. Figure 48. Command Line Controller Block Diagram TX Pointer 5-Byte FIFO CTPTR MMCMD Write MMCON0.4 Data Converter // -> Serial CRC7 Generator TX COMMAND Line Finished State Machine CFLCK MMSTA.0 CRPTR MMCON0.5 CMDEN MCMD 17 - Byte FIFO Data Converter Serial -> // MMSTA.2 MMSTA.1 CRC7S RESPFS CRC7 and Format Checker MMCMD Read RX COMMAND Line Finished State Machine RESPEN RFMT MMINT.6 EORI CRCDIS MMCON1.1 MMCON0.1 MMCON0.0 Command Receiver Command Transmitter EOCI MMCON1.0 Command Transmitter RX Pointer MMINT.5 For sending a command to the card, user must load the command index (1 Byte) and argument (4 Bytes) in the command transmit FIFO using the MMCMD register. Before starting transmission by setting and clearing the CMDEN bit in MMCON1 register, user must first configure: • RESPEN bit in MMCON1 register to indicate whether a response is expected or not. • RFMT bit in MMCON0 register to indicate the response size expected. • CRCDIS bit in MMCON0 register to indicate whether the CRC7 included in the response will be computed or not. In order to avoid CRC error, CRCDIS may be set for response that do not include CRC7. Figure 49 summarizes the command transmission flow. As soon as command transmission is enabled, the CFLCK flag in MMSTA is set indicating that write to the FIFO is locked. This mechanism is implemented to avoid command overrun. The end of the command transmission is signalled to you by the EOCI flag in MMINT register becoming set. This flag may generate an MMC interrupt request as detailed in Section "Interrupt", page 66. The end of the command transmission also resets the CFLCK flag. 58 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 User may abort command loading by setting and clearing the CTPTR bit in MMCON0 register which resets the write pointer to the transmit FIFO. Figure 49. Command Transmission Flow Command Transmission Configure Response RESPEN = X RFMT = X CRCDIS = X Load Command in Buffer MMCMD = index MMCMD = argument Transmit Command CMDEN = 1 CMDEN = 0 Command Receiver The end of the response reception is signalled to you by the EORI flag in MMINT register. This flag may generate an MMC interrupt request as detailed in Section "Interrupt", page 66. When this flag is set, 2 other flags in MMSTA register: RESPFS and CRC7S give a status on the response received. RESPFS indicates if the response format is correct or not: the size is the one expected (48 bits or 136 bits) and a valid End bit has been received, and CRC7S indicates if the CRC7 computation is correct or not. These Flags are cleared when a command is sent to the card and updated when the response has been received. User may abort response reading by setting and clearing the CRPTR bit in MMCON0 register which resets the read pointer to the receive FIFO. According to the MMC specification delay between a command and a response (formally NCR parameter) can not exceed 64 MMC clock periods. To avoid any locking of the MMC controller when card does not send its response (e.g. physically removed from the bus), user must launch a time-out period to exit from such situation. In case of timeout user may reset the command controller and its internal state machine by setting and clearing the CCR bit in MMCON2 register. This time-out may be disarmed when receiving the response. 59 7524D–MP3–07/07 Data Line Controller The data line controller is based on a 16-Byte FIFO used both by the data transmitter channel and by the data receiver channel. Figure 50. Data Line Controller Block Diagram MMINT.0 MMINT.2 MMSTA.3 MMSTA.4 F1EI F1FI DATFS CRC16S CRC16 and Format Checker Data Converter Serial -> // 8-Byte TX Pointer FIFO 1 DTPTR MMCON0.6 RX Pointer DRPTR MMCON0.7 16-Byte FIFO MMDAT MCBI CBUSY MMINT.1 MMSTA.5 MDAT Data Converter // -> Serial CRC16 Generator 8-Byte MMINT.4 DATA Line Finished State Machine FIFO 2 F2EI F2FI MMINT.1 MMINT.3 DFMT MBLOCK DATEN MMCON0.2 MMCON0.3 MMCON1.2 DATDIR EOFI BLEN3:0 MMCON1.3 MMCON1.7:4 FIFO Implementation The 16-Byte FIFO is based on a dual 8-Byte FIFOs managed using 2 pointers and four flags indicating the status full and empty of each FIFO. Pointers are not accessible to user but can be reset at any time by setting and clearing DRPTR and DTPTR bits in MMCON0 register. Resetting the pointers is equivalent to abort the writing or reading of data. F1EI and F2EI flags in MMINT register signal when set that respectively FIFO1 and FIFO2 are empty. F1FI and F2FI flags in MMINT register signal when set that respectively FIFO1 and FIFO2 are full. These flags may generate an MMC interrupt request as detailed in Section “Interrupt”. Data Configuration Before sending or receiving any data, the data line controller must be configured according to the type of the data transfer considered. This is achieved using the Data Format bit: DFMT in MMCON0 register. Clearing DFMT bit enables the data stream format while setting DFMT bit enables the data block format. In data block format, user must also configure the single or multi-block mode by clearing or setting the MBLOCK bit in MMCON0 register and the block length using BLEN3:0 bits in MMCON1 according to Table 54. Figure 51 summarizes the data modes configuration flows. Table 54. Block Length Programming BLEN3:0 BLEN = 0000 to 1011 > 1011 60 Block Length (Byte) Length = 2BLEN: 1 to 2048 Reserved: do not program BLEN3:0 > 1011 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 51. Data Controller Configuration Flows Data Stream Configuration Data Single Block Configuration Data Multi-Block Configuration Configure Format DFMT = 0 Configure Format DFMT = 1 MBLOCK = 0 BLEN3:0 = XXXXb Configure Format DFMT = 1 MBLOCK = 1 BLEN3:0 = XXXXb Data Transmitter Configuration For transmitting data to the card user must first configure the data controller in transmission mode by setting the DATDIR bit in MMCON1 register. Figure 52 summarizes the data stream transmission flows in both polling and interrupt modes while Figure 53 summarizes the data block transmission flows in both polling and interrupt modes, these flows assume that block length is greater than 16 data. Data Loading Data is loaded in the FIFO by writing to MMDAT register. Number of data loaded may vary from 1 to 16 Bytes. Then if necessary (more than 16 Bytes to send) user must wait that one FIFO becomes empty (F1EI or F2EI set) before loading 8 new data. Data Transmission Transmission is enabled by setting and clearing DATEN bit in MMCON1 register. Data is transmitted immediately if the response has already been received, or is delayed after the response reception if its status is correct. In both cases transmission is delayed if a card sends a busy state on the data line until the end of this busy condition. According to the MMC specification, the data transfer from the host to the card may not start sooner than 2 MMC clock periods after the card response was received (formally N WR parameter). To address all card types, this delay can be programmed using DATD1:0 bits in MMCON2 register from 3 MMC clock periods when DATD1:0 bits are cleared to 9 MMC clock periods when DATD1:0 bits are set, by step of 2 MMC clock periods. End of Transmission The end of a data frame (block or stream) transmission is signalled to you by the EOFI flag in MMINT register. This flag may generate an MMC interrupt request as detailed in Section "Interrupt", page 66. In data stream mode, EOFI flag is set, after reception of the End bit. This assumes user has previously sent the STOP command to the card, which is the only way to stop stream transfer. In data block mode, EOFI flag is set, after reception of the CRC status token (see Figure 43). 2 other flags in MMSTA register: DATFS and CRC16S report a status on the frame sent. DATFS indicates if the CRC status token format is correct or not, and CRC16S indicates if the card has found the CRC16 of the block correct or not. Busy Status As shown in Figure 43 the card uses a busy token during a block write operation. This busy status is reported to you by the CBUSY flag in MMSTA register and by the MCBI flag in MMINT which is set every time CBUSY toggles, i.e. when the card enters and exits its busy state. This flag may generate an MMC interrupt request as detailed in Section "Interrupt", page 66. 61 7524D–MP3–07/07 Figure 52. Data Stream Transmission Flows Data Stream Transmission Data Stream Initialization FIFOs Filling write 16 data to MMDAT FIFOs Filling write 16 data to MMDAT Start Transmission DATEN = 1 DATEN = 0 Unmask FIFOs Empty F1EM = 0 F2EM = 0 FIFO Empty? F1EI or F2EI = 1? Start Transmission DATEN = 1 DATEN = 0 FIFO Filling write 8 data to MMDAT No More Data To Send? Send STOP Command Data Stream Transmission ISR FIFO Empty? F1EI or F2EI = 1? FIFO Filling write 8 data to MMDAT No More Data To Send? Mask FIFOs Empty F1EM = 1 F2EM = 1 Send STOP Command b. Interrupt mode a. Polling mode 62 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 53. Data Block Transmission Flows Data Block Transmission Data Block Initialization FIFOs Filling write 16 data to MMDAT FIFOs Filling write 16 data to MMDAT Start Transmission DATEN = 1 DATEN = 0 Unmask FIFOs Empty F1EM = 0 F2EM = 0 FIFO Empty? F1EI or F2EI = 1? Start Transmission DATEN = 1 DATEN = 0 FIFO Filling write 8 data to MMDAT No More Data To Send? Data Block Transmission ISR FIFO Empty? F1EI or F2EI = 1? FIFO Filling write 8 data to MMDAT No More Data To Send? Mask FIFOs Empty F1EM = 1 F2EM = 1 b. Interrupt mode a. Polling mode Data Receiver Configuration To receive data from the card you must first configure the data controller in reception mode by clearing the DATDIR bit in MMCON1 register. Figure 54 summarizes the data stream reception flows in both polling and interrupt modes while Figure 55 summarizes the data block reception flows in both polling and interrupt modes, these flows assume that block length is greater than 16 Bytes. Data Reception The end of a data frame (block or stream) reception is signalled to you by the EOFI flag in MMINT register. This flag may generate an MMC interrupt request as detailed in Section "Interrupt", page 66. When this flag is set, 2 other flags in MMSTA register: DATFS and CRC16S give a status on the frame received. DATFS indicates if the frame format is correct or not: a valid End bit has been received, and CRC16S indicates if the CRC16 computation is correct or not. In case of data stream CRC16S has no meaning and stays cleared. According to the MMC specification data transmission from the card starts after the access time delay (formally NAC parameter) beginning from the End bit of the read command. To avoid any locking of the MMC controller when card does not send its data (e.g. physically removed from the bus), you must launch a time-out period to exit from such situation. In case of time-out you may reset the data controller and its internal state machine by setting and clearing the DCR bit in MMCON2 register. 63 7524D–MP3–07/07 This time-out may be disarmed after receiving 8 data (F1FI flag set) or after receiving end of frame (EOFI flag set) in case of block length less than 8 data (1, 2 or 4). Data is read from the FIFO by reading to MMDAT register. Each time one FIFO becomes full (F1FI or F2FI set), user is requested to flush this FIFO by reading 8 data. Data Reading Figure 54. Data Stream Reception Flows Data Stream Reception Data Stream Initialization Data Stream Reception ISR FIFO Full? F1FI or F2FI = 1? Unmask FIFOs Full F1FM = 0 F2FM = 0 FIFO Full? F1FI or F2FI = 1? FIFO Reading read 8 data from MMDAT FIFO Reading read 8 data from MMDAT No More Data To Receive? No More Data To Receive? Send STOP Command Mask FIFOs Full F1FM = 1 F2FM = 1 a. Polling mode Send STOP Command b. Interrupt mode 64 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 55. Data Block Reception Flows Data Block Reception Data Block Initialization Data Block Reception ISR Start Transmission DATEN = 1 DATEN = 0 Unmask FIFOs Full F1FM = 0 F2FM = 0 FIFO Full? F1EI or F2EI = 1? FIFO Full? F1EI or F2EI = 1? Start Transmission DATEN = 1 DATEN = 0 FIFO Reading read 8 data from MMDAT No More Data To Receive? FIFO Reading read 8 data from MMDAT Mask FIFOs Full F1FM = 1 F2FM = 1 No More Data To Receive? a. Polling mode Flow Control b. Interrupt mode To allow transfer at high speed without taking care of CPU oscillator frequency, the FLOWC bit in MMCON2 allows control of the data flow in both transmission and reception. During transmission, setting the FLOWC bit has the following effects: • MMCLK is stopped when both FIFOs become empty: F1EI and F2EI set. • MMCLK is restarted when one of the FIFOs becomes full: F1EI or F2EI cleared. During reception, setting the FLOWC bit has the following effects: • MMCLK is stopped when both FIFOs become full: F1FI and F2FI set. • MMCLK is restarted when one of the FIFOs becomes empty: F1FI or F2FI cleared. As soon as the clock is stopped, the MMC bus is frozen and remains in its state until the clock is restored by writing or reading data in MMDAT. 65 7524D–MP3–07/07 Interrupt Description As shown in Figure 56, the MMC controller implements eight interrupt sources reported in MCBI, EORI, EOCI, EOFI, F2FI, F1FI, and F2EI flags in MMCINT register. These flags are detailed in the previous sections. All these sources are maskable separately using MCBM, EORM, EOCM, EOFM, F2FM, F1FM, and F2EM mask bits respectively in MMMSK register. The interrupt request is generated each time an unmasked flag is set, and the global MMC controller interrupt enable bit is set (EMMC in IEN1 register). Reading the MMINT register automatically clears the interrupt flags (acknowledgment). This implies that register content must be saved and tested interrupt flag by interrupt flag to be sure not to forget any interrupts. Figure 56. MMC Controller Interrupt System MCBI MMINT.7 MCBM MMMSK.7 EORI MMINT.6 EORM EOCI MMMSK.6 MMINT.5 EOCM MMMSK.5 EOFI MMINT.4 MMC Interface Interrupt Request EOFM F2FI MMMSK.4 EMMC MMINT.3 F2FM IEN1.0 MMMSK.3 F1FI MMINT.2 F1FM F2EI MMMSK.2 MMINT.1 F2EM MMMSK.1 F1EI MMINT.0 F1EM MMMSK.0 66 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Serial I/O Port The serial I/O port in the AT83SND2CMP3 provides both synchronous and asynchronous communication modes. It operates as a Synchronous Receiver and Transmitter in one single mode (Mode 0) and operates as an Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous modes support framing error detection and multiprocessor communication with automatic address recognition. Mode Selection SM0 and SM1 bits in SCON register are used to select a mode among the single synchronous and the three asynchronous modes according to Table 55. Table 55. Serial I/O Port Mode Selection Baud Rate Generator SM0 SM1 Mode Description Baud Rate 0 0 0 Synchronous Shift Register Fixed/Variable 0 1 1 8-bit UART Variable 1 0 2 9-bit UART Fixed 1 1 3 9-bit UART Variable Depending on the mode and the source selection, the baud rate can be generated from either the Timer 1 or the Internal Baud Rate Generator. The Timer 1 can be used in Modes 1 and 3 while the Internal Baud Rate Generator can be used in Modes 0, 1 and 3. The addition of the Internal Baud Rate Generator allows freeing of the Timer 1 for other purposes in the application. It is highly recommended to use the Internal Baud Rate Generator as it allows higher and more accurate baud rates than Timer 1. Baud rate formulas depend on the modes selected and are given in the following mode sections. Timer 1 When using Timer 1, the Baud Rate is derived from the overflow of the timer. As shown in Figure 57 Timer 1 is used in its 8-bit auto-reload mode (detailed in Section "Mode 2 (8-bit Timer with Auto-Reload)", page 53). SMOD1 bit in PCON register allows doubling of the generated baud rate. Figure 57. Timer 1 Baud Rate Generator Block Diagram PER CLOCK ÷6 0 1 TL1 (8 bits) T1 Overflow ÷2 0 1 To serial Port C/T1# TMOD.6 SMOD1 INT1 GATE1 TMOD.7 TR1 PCON.7 TH1 (8 bits) T1 CLOCK TCON.6 67 7524D–MP3–07/07 Internal Baud Rate Generator When using the Internal Baud Rate Generator, the Baud Rate is derived from the overflow of the timer. As shown in Figure 58 the Internal Baud Rate Generator is an 8-bit auto-reload timer fed by the peripheral clock or by the peripheral clock divided by 6 depending on the SPD bit in BDRCON register. The Internal Baud Rate Generator is enabled by setting BBR bit in BDRCON register. SMOD1 bit in PCON register allows doubling of the generated baud rate. Figure 58. Internal Baud Rate Generator Block Diagram PER CLOCK ÷6 0 BRG (8 bits) 1 Overflow ÷2 0 To serial Port 1 SPD BRR BDRCON.1 BDRCON.4 SMOD1 PCON.7 BRL (8 bits) Synchronous Mode (Mode 0) IBRG CLOCK Mode 0 is a half-duplex, synchronous mode, which is commonly used to expand the I/0 capabilities of a device with shift registers. The transmit data (TXD) pin outputs a set of eight clock pulses while the receive data (RXD) pin transmits or receives a Byte of data. The 8-bit data are transmitted and received least-significant bit (LSB) first. Shifts occur at a fixed Baud Rate (see Section "Baud Rate Selection (Mode 0)", page 69). Figure 59 shows the serial port block diagram in Mode 0. Figure 59. Serial I/O Port Block Diagram (Mode 0) SCON.6 SCON.7 SM1 SM0 SBUF Tx SR Mode Decoder RXD M3 M2 M1 M0 SBUF Rx SR Mode Controller PER CLOCK Transmission (Mode 0) TI RI SCON.1 SCON.0 BRG CLOCK Baud Rate Controller TXD To start a transmission mode 0, write to SCON register clearing bits SM0, SM1. As shown in Figure 60, writing the Byte to transmit to SBUF register starts the transmission. Hardware shifts the LSB (D0) onto the RXD pin during the first clock cycle composed of a high level then low level signal on TXD. During the eighth clock cycle the MSB (D7) is on the RXD pin. Then, hardware drives the RXD pin high and asserts TI to indicate the end of the transmission. 68 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 60. Transmission Waveforms (Mode 0) TXD Write to SBUF RXD D0 D1 D2 D3 D4 D5 D6 D7 TI Reception (Mode 0) To start a reception in mode 0, write to SCON register clearing SM0, SM1 and RI bits and setting the REN bit. As shown in Figure 61, Clock is pulsed and the LSB (D0) is sampled on the RXD pin. The D0 bit is then shifted into the shift register. After eight samplings, the MSB (D7) is shifted into the shift register, and hardware asserts RI bit to indicate a completed reception. Software can then read the received Byte from SBUF register. Figure 61. Reception Waveforms (Mode 0) TXD Set REN, Clear RI Write to SCON RXD D0 D1 D2 D3 D4 D5 D6 D7 RI Baud Rate Selection (Mode 0) In mode 0, the baud rate can be either, fixed or variable. As shown in Figure 62, the selection is done using M0SRC bit in BDRCON register. Figure 63 gives the baud rate calculation formulas for each baud rate source. Figure 62. Baud Rate Source Selection (mode 0) PER CLOCK ÷6 0 To Serial Port 1 IBRG CLOCK M0SRC BDRCON.0 Figure 63. Baud Rate Formulas (Mode 0) Baud_Rate= Baud_Rate= FPER 6 a. Fixed Formula BRL= 256 - 6 6 2SMOD1 ⋅ FPER ⋅ 32 ⋅ (256 -BRL) (1-SPD) 2SMOD1 ⋅ FPER ⋅ 32 ⋅ Baud_Rate (1-SPD) b. Variable Formula 69 7524D–MP3–07/07 Asynchronous Modes (Modes 1, 2 and 3) The Serial Port has one 8-bit and 2 9-bit asynchronous modes of operation. Figure 64 shows the Serial Port block diagram in such asynchronous modes. Figure 64. Serial I/O Port Block Diagram (Modes 1, 2 and 3) SCON.6 SCON.7 SCON.3 SM1 SM0 TB8 Mode Decoder SBUF Tx SR TXD Rx SR RXD M3 M2 M1 M0 T1 CLOCK Mode & Clock Controller IBRG CLOCK SBUF Rx PER CLOCK SM2 TI RI SCON.4 SCON.1 SCON.0 RB8 SCON.2 Mode 1 is a full-duplex, asynchronous mode. The data frame (see Figure 65) consists of 10 bits: one start, eight data bits and one stop bit. Serial data is transmitted on the TXD pin and received on the RXD pin. When a data is received, the stop bit is read in the RB8 bit in SCON register. Mode 1 Figure 65. Data Frame Format (Mode 1) Mode 1 D0 D1 D2 Start bit Modes 2 and 3 D3 D4 D5 D6 D7 8-bit data Stop bit Modes 2 and 3 are full-duplex, asynchronous modes. The data frame (see Figure 66) consists of 11 bits: one start bit, eight data bits (transmitted and received LSB first), one programmable ninth data bit and one stop bit. Serial data is transmitted on the TXD pin and received on the RXD pin. On receive, the ninth bit is read from RB8 bit in SCON register. On transmit, the ninth data bit is written to TB8 bit in SCON register. Alternatively, you can use the ninth bit can be used as a command/data flag. Figure 66. Data Frame Format (Modes 2 and 3) D0 Start bit D1 D2 D3 D4 9-bit data D5 D6 D7 D8 Stop bit Transmission (Modes 1, 2 and 3) To initiate a transmission, write to SCON register, set the SM0 and SM1 bits according to Table 55, and set the ninth bit by writing to TB8 bit. Then, writing the Byte to be transmitted to SBUF register starts the transmission. Reception (Modes 1, 2 and 3) To prepare for reception, write to SCON register, set the SM0 and SM1 bits according to Table 55, and set the REN bit. The actual reception is then initiated by a detected highto-low transition on the RXD pin. 70 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Framing Error Detection (Modes 1, 2 and 3) Framing error detection is provided for the three asynchronous modes. To enable the framing bit error detection feature, set SMOD0 bit in PCON register as shown in Figure 67. When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous transmission by 2 devices. If a valid stop bit is not found, the software sets FE bit in SCON register. Software may examine FE bit after each reception to check for data errors. Once set, only software or a chip reset clear FE bit. Subsequently received frames with valid stop bits cannot clear FE bit. When the framing error detection feature is enabled, RI rises on stop bit instead of the last data bit as detailed in Figure 73. Figure 67. Framing Error Block Diagram Framing Error Controller FE 1 SM0/FE 0 SCON.7 SM0 SMOD0 PCON.6 Baud Rate Selection (Modes 1 and 3) In modes 1 and 3, the Baud Rate is derived either from the Timer 1 or the Internal Baud Rate Generator and allows different baud rate in reception and transmission. As shown in Figure 68 the selection is done using RBCK and TBCK bits in BDRCON register. Figure 69 gives the baud rate calculation formulas for each baud rate source while Table 56 details Internal Baud Rate Generator configuration for different peripheral clock frequencies and giving baud rates closer to the standard baud rates. Figure 68. Baud Rate Source Selection (Modes 1 and 3) T1 CLOCK 0 ÷ 16 1 IBRG CLOCK To Serial Rx Port T1 CLOCK 0 ÷ 16 IBRG CLOCK RBCK BDRCON.2 1 To Serial Tx Port TBCK BDRCON.3 Figure 69. Baud Rate Formulas (Modes 1 and 3) Baud_Rate= BRL= 256 - 6 6 2SMOD1 ⋅ FPER ⋅ 32 ⋅ (256 -BRL) (1-SPD) 2SMOD1 ⋅ FPER ⋅ 32 ⋅ Baud_Rate (1-SPD) a. IBRG Formula Baud_Rate= TH1= 256 - 2SMOD1 ⋅ FPER 6 ⋅ 32 ⋅ (256 -TH1) 2SMOD1 ⋅ FPER 192 ⋅ Baud_Rate b. T1 Formula 71 7524D–MP3–07/07 Table 56. Internal Baud Rate Generator Value FPER = 6 MHz(1) FPER = 8 MHz(1) FPER = 10 MHz(1) Baud Rate SPD SMOD1 BRL Error % SPD SMOD1 BRL Error % SPD SMOD1 BRL Error % 115200 - - - - - - - - - - - - 57600 - - - - 1 1 247 3.55 1 1 245 1.36 38400 1 1 246 2.34 1 1 243 0.16 1 1 240 1.73 19200 1 1 236 2.34 1 1 230 0.16 1 1 223 1.36 9600 1 1 217 0.16 1 1 204 0.16 1 1 191 0.16 4800 1 1 178 0.16 1 1 152 0.16 1 1 126 0.16 FPER = 12 MHz(2) FPER = 16 MHz(2) FPER = 20 MHz(2) Baud Rate SPD SMOD1 BRL Error % SPD SMOD1 BRL Error % SPD SMOD1 BRL Error % 115200 - - - - 1 1 247 3.55 1 1 245 1.36 57600 1 1 243 0.16 1 1 239 2.12 1 1 234 1.36 38400 1 1 236 2.34 1 1 230 0.16 1 1 223 1.36 19200 1 1 217 0.16 1 1 204 0.16 1 1 191 0.16 9600 1 1 178 0.16 1 1 152 0.16 1 1 126 0.16 4800 1 1 100 0.16 1 1 48 0.16 1 0 126 0.16 Notes: 1. These frequencies are achieved in X1 mode, FPER = FOSC ÷ 2. 2. These frequencies are achieved in X2 mode, FPER = FOSC. Baud Rate Selection (Mode 2) In mode 2, the baud rate can only be programmed to 2 fixed values: 1/16 or 1/32 of the peripheral clock frequency. As shown in Figure 70 the selection is done using SMOD1 bit in PCON register. Figure 71 gives the baud rate calculation formula depending on the selection. Figure 70. Baud Rate Generator Selection (Mode 2) PER CLOCK ÷2 0 ÷ 16 To Serial Port 1 SMOD1 PCON.7 72 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 71. Baud Rate Formula (Mode 2) Baud_Rate= Multiprocessor Communication (Modes 2 and 3) 2SMOD1 ⋅ FPER 32 Modes 2 and 3 provide a ninth-bit mode to facilitate multiprocessor communication. To enable this feature, set SM2 bit in SCON register. When the multiprocessor communication feature is enabled, the serial Port can differentiate between data frames (ninth bit clear) and address frames (ninth bit set). This allows the AT83SND2CMP3 to function as a slave processor in an environment where multiple slave processors share a single serial line. When the multiprocessor communication feature is enabled, the receiver ignores frames with the ninth bit clear. The receiver examines frames with the ninth bit set for an address match. If the received address matches the slaves address, the receiver hardware sets RB8 and RI bits in SCON register, generating an interrupt. The addressed slave’s software then clears SM2 bit in SCON register and prepares to receive the data Bytes. The other slaves are unaffected by these data Bytes because they are waiting to respond to their own addresses. Automatic Address Recognition The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled (SM2 bit in SCON register is set). Implemented in hardware, automatic address recognition enhances the multiprocessor communication feature by allowing the Serial Port to examine the address of each incoming command frame. Only when the Serial Port recognizes its own address, the receiver sets RI bit in SCON register to generate an interrupt. This ensures that the CPU is not interrupted by command frames addressed to other devices. If desired, the automatic address recognition feature in mode 1 may be enabled. In this configuration, the stop bit takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the device’s address and is terminated by a valid stop bit. To support automatic address recognition, a device is identified by a given address and a broadcast address. Note: Given Address The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e, setting SM2 bit in SCON register in mode 0 has no effect). Each device has an individual address that is specified in SADDR register; the SADEN register is a mask Byte that contains don’t care bits (defined by zeros) to form the device’s given address. The don’t care bits provide the flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed. To address a device by its individual address, the SADEN mask Byte must be 1111 1111b. For example: SADDR = 0101 0110b SADEN = 1111 1100b Given = 0101 01XXb 73 7524D–MP3–07/07 The following is an example of how to use given addresses to address different slaves: Slave A:SADDR = 1111 0001b SADEN = 1111 1010b Given = 1111 0X0Xb Slave B:SADDR = 1111 0011b SADEN = 1111 1001b Given = 1111 0XX1b Slave C:SADDR = 1111 0011b SADEN = 1111 1101b Given = 1111 00X1b The SADEN Byte is selected so that each slave may be addressed separately. For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To communicate with slave A only, the master must send an address where bit 0 is clear (e.g. 1111 0000B). For slave A, bit 1 is a 0; for slaves B and C, bit 1 is a don’t care bit. To communicate with slaves A and B, but not slave C, the master must send an address with bits 0 and 1 both set (e.g. 1111 0011B). To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2 clear (e.g. 1111 0001B). Broadcast Address A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as don’t-care bits, e.g.: SADDR = 0101 0110b SADEN = 1111 1100b (SADDR | SADEN)=1111 111Xb The use of don’t-care bits provides flexibility in defining the broadcast address, however in most applications, a broadcast address is FFh. The following is an example of using broadcast addresses: Slave A:SADDR = 1111 0001b SADEN = 1111 1010b Given = 1111 1X11b, Slave B:SADDR = 1111 0011b SADEN = 1111 1001b Given = 1111 1X11b, Slave C:SADDR = 1111 0010b SADEN = 1111 1101b Given = 1111 1111b, For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the master must send the address FFh. To communicate with slaves A and B, but not slave C, the master must send the address FBh. Reset Address 74 On reset, the SADDR and SADEN registers are initialized to 00h, i.e. the given and broadcast addresses are XXXX XXXXb (all don’t care bits). This ensures that the Serial Port is backwards compatible with the 80C51 microcontrollers that do not support automatic address recognition. AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Interrupt The Serial I/O Port handles 2 interrupt sources that are the “end of reception” (RI in SCON) and “end of transmission” (TI in SCON) flags. As shown in Figure 72 these flags are combined together to appear as a single interrupt source for the C51 core. Flags must be cleared by software when executing the serial interrupt service routine. The serial interrupt is enabled by setting ES bit in IEN0 register. This assumes interrupts are globally enabled by setting EA bit in IEN0 register. Depending on the selected mode and weather the framing error detection is enabled or disabled, RI flag is set during the stop bit or during the ninth bit as detailed in Figure 73. Figure 72. Serial I/O Interrupt System SCON.0 RI Serial I/O Interrupt Request TI SCON.1 ES IEN0.4 Figure 73. Interrupt Waveforms a. Mode 1 RXD D0 D1 D2 Start Bit D3 D4 D5 D6 D7 8-bit Data Stop Bit RI SMOD0 = X FE SMOD0 = 1 b. Mode 2 and 3 RXD D0 Start bit D1 D2 D3 D4 9-bit data D5 D6 D7 D8 Stop bit RI SMOD0 = 0 RI SMOD0 = 1 FE SMOD0 = 1 75 7524D–MP3–07/07 Keyboard Interface The AT83SND2CMP3 implement a keyboard interface allowing the connection of a keypad. It is based on one input with programmable interrupt capability on both high or low level. This input allows exit from idle and power down modes. Description The keyboard interfaces with the C51 core through 2 special function registers: KBCON, the keyboard control register; and KBSTA, the keyboard control and status register. An interrupt enable bit (EKB in IEN1 register) allows global enable or disable of the keyboard interrupt (see Figure 74). As detailed in Figure 75 this keyboard input has the capability to detect a programmable level according to KINL0 bit value in KBCON register. Level detection is then reported in interrupt flag KINF0 in KBSTA register. A keyboard interrupt is requested each time this flag is set. This flag can be masked by software using KINM0 bits in KBCON register and is cleared by reading KBSTA register. Figure 74. Keyboard Interface Block Diagram KIN0 Keyboard Interface Interrupt Request Input Circuitry EKB IEN1.4 Figure 75. Keyboard Input Circuitry 0 KIN0 KINF0 1 KBSTA.0 KINM0 KINL0 KBCON.0 KBCON.4 Power Reduction Mode KIN0 inputs allow exit from idle and power-down modes as detailed in section “Power Management”, page 46. To enable this feature, KPDE bit in KBSTA register must be set to logic 1. Due to the asynchronous keypad detection in power down mode (all clocks are stopped), exit may happen on parasitic key press. In this case, no key is detected and software must enter power down again. 76 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Electrical Characteristics Absolute Maximum Rating Storage Temperature ......................................... -65 to +150°C Voltage on any other Pin to VSS .................................... -0.3 *NOTICE: to +4.0 V IOL per I/O Pin ................................................................. 5 mA Power Dissipation ............................................................. 1 W Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage. These are stress ratings only. Operation beyond the “operating conditions” is not recommended and extended exposure beyond the “Operating Conditions” may affect device reliability. Operating Conditions Ambient Temperature Under Bias........................ -40 to +85°C VDD ......................................................................................................... 2.7 to 3.3V DC Characteristics Digital Logic Table 57. Digital DC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol VIL VIH1 (2) Parameter Min Input Low Voltage Input High Voltage (except RST, X1) Typ(1) Max Units -0.5 0.2·VDD - 0.1 V 0.2·VDD + 1.1 VDD V 0.7·VDD VDD + 0.5 V Test Conditions VIH2 Input High Voltage (RST, X1) VOL1 Output Low Voltage (except P0, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) 0.45 V IOL= 1.6 mA VOL2 Output Low Voltage (P0, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) 0.45 V IOL= 3.2 mA VOH1 Output High Voltage (P1, P2, P3, P4 and P5) VDD - 0.7 V IOH= -30 µA VOH2 Output High Voltage (P0, P2 address mode, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT, D+, D-) VDD - 0.7 V IOH= -3.2 mA IIL Logical 0 Input Current (P1, P2, P3, P4 and P5) -50 µA VIN= 0.45 V ILI Input Leakage Current (P0, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) 10 µA 0.45< VIN< VDD ITL Logical 1 to 0 Transition Current (P1, P2, P3, P4 and P5) -650 µA VIN= 2.0 V 200 kΩ RRST CIO VRET Pull-Down Resistor Pin Capacitance VDD Data Retention Limit 50 90 10 pF 1.8 TA= 25°C V IDD 77 7524D–MP3–07/07 Table 57. Digital DC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Typ(1) Min Max Units VDD < 3.3 V AT83SND2CMP3 Operating Current X1 / X2 mode 7/ 11.5 9/ 14.5 10.5 / 18 IDL AT83SND2CMP3 Idle Mode Current X1 / X2 mode 6.3 / 9.1 7.4 / 11.3 8.5 / 14 mA IPD AT83SND2CMP3 Power-Down Mode Current 500 µA IDD 20 Notes: Test Conditions mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V 12 MHz 16 MHz 20 MHz VRET < VDD < 3.3 V 1. Typical values are obtained using VDD= 3 V and TA= 25°C. They are not tested and there is no guarantee on these values. Table 58. Typical Reference Design AT83SND2CMP3 Power Consumption Player Mode IDD Test Conditions Stop 10 mA AT83SND2CMP3 at 16 MHz, X2 mode, VDD= 3 V No song playing. This consumption does not include AUDVBAT current. Playing 37 mA AT83SND2CMP3 at 16 MHz, X2 mode, VDD= 3 V MP3 Song with Fs= 44.1 KHz, at any bit rates (Variable Bit Rate) This consumption does not include AUDVBAT current. IDD, IDL and IPD Test Conditions Figure 76. IDD Test Condition, Active Mode VDD VDD RST (NC) Clock Signal VDD PVDD UVDD AUDVDD X2 X1 IDD VDD P0 VSS PVSS UVSS AUDVSS VSS 78 TST All other pins are unconnected AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 77. IDL Test Condition, Idle Mode VDD VDD PVDD UVDD AUDVDD RST VSS (NC) Clock Signal X2 X1 IDL VDD P0 VSS PVSS UVSS AUDVSS VSS TST All other pins are unconnected Figure 78. IPD Test Condition, Power-Down Mode VDD VDD PVDD UVDD AUDVDD RST VSS (NC) X2 X1 VDD P0 MCMD VSS PVSS UVSS AUDVSS VSS IPD MDAT TST All other pins are unconnected Oscillator & Crystal Schematic Figure 79. Crystal Connection X1 C1 Q C2 VSS Note: Parameters X2 For operation with most standard crystals, no external components are needed on X1 and X2. It may be necessary to add external capacitors on X1 and X2 to ground in special cases (max 10 pF). X1 and X2 may not be used to drive other circuits. Table 59. Oscillator & Crystal Characteristics 79 7524D–MP3–07/07 VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Min Typ Max Unit CX1 Internal Capacitance (X1 - VSS) 10 pF CX2 Internal Capacitance (X2 - VSS) 10 pF CL Equivalent Load Capacitance (X1 - X2) 5 pF DL Drive Level 50 µW Crystal Frequency 20 MHz RS Crystal Series Resistance 40 Ω CS Crystal Shunt Capacitance 6 pF Max Unit F Phase Lock Loop Schematic Figure 80. PLL Filter Connection FILT R C2 C1 VSS Parameters VSS Table 60. PLL Filter Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Min Typ R Filter Resistor 100 Ω C1 Filter Capacitance 1 10 nF C2 Filter Capacitance 2 2.2 nF USB Connection Schematic Figure 81. USB Connection VBUS D+ To Power Supply RUSB D- RUSB D+ D- GND VSS Parameters Table 61. USB Termination Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol RUSB 80 Parameter USB Termination Resistor Min Typ 27 Max Unit Ω AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 DAC and PA Electrical Specifications AUDVBAT = 3.6V, TA = 25°C unless otherwise noted. PA High power mode, 100nF capacitor connected between CBP and AUDVSS, 470nF input capacitors, Load = 8 ohms. Figure 82. PA Specification Symbol AUDVBAT IDD Parameter Conditions Supply Voltage Min Typ Max Unit 3.2 - 5.5 V Quiescent Current Inputs shorted, no load - 6 8 mA IDDstby Standby Current Capacitance - - 2 µA VCBP DC Reference - AUDVBAT/2 - V VOS Output differential offset full gain -20 0 20 mV Input impedance Active state 12K 20k 30k W ZLFP Output load Full Power mode 6 8 32 W ZLLP Output load Low-Power mode 100 150 300 W - - 100 pF - 60 - dB 50 - 20000 Hz - - 10 ms ZIN CL PSRR Capacitive load 200 – 2kHz Power supply rejection ratio Differential output 1KHz reference frequency BW Output Frequency bandwidth 3dB attenuation. 470nF input coupling capacitors Off to on mode. Voltage already settled. tUP Output setup time VN Output noise Max gain, A weighted - 120 500 µVRMS THDHP Output distortion High power mode, VDD = 3.2V, 1KHz, Pout=100mW, gain=0dB - 50 - dB THDLP Output distortion Low power mode, VDD = 3.2V , 1KHz, Vout= 100mVpp, Max gain, load 8 ohms in serie with 200 ohms - 1 - % -2 0 2 dB -0.7 0 0.7 dB GACC Overall Gain accuracy GSTEP Gain Step Accuracy Input capacitors precharged Figure 83. Maximum Dissipated Power Versus Power Supply 81 7524D–MP3–07/07 600 Dissipated Power [mW] 550 500 450 8 Ohms load 400 6.5 Ohms load 350 300 250 200 3,2 3,4 3,6 3,8 4 Supply Voltage AUDVBAT [V] 4,2 Figure 84. Dissipated Power vs Output Power, AUDVBAT = 3.2V 600 550 Dissipated Power [mW] 500 450 400 350 8 Ohms load 300 6.5 Ohms load 250 200 150 100 50 0 0 100 200 300 400 500 600 700 800 Output Power [mW] DAC AUDVDD, HSVDD = 2.8 V, Ta=25°C, typical case, unless otherwise noted All noise and distortion specifications are measured in the 20 Hz to 0.425xFs and Aweighted filtered. Full Scale levels scale proportionally with the analog supply voltage. Figure 85. Audio DAC Specification 82 OVERALL MIN TYP MAX UNITS Operating Temperature -40 +25 +125 °C Analog Supply Voltage (AUDVDD, HSVDD) 2.7 2.8 3.3 V AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 OVERALL MIN TYP MAX UNITS Digital Supply Voltage (VDD) 2.4 2.8 3.3 V Audio Amplifier Supply (AUDVBAT) 3.2 - 5.5 V DIGITAL INPUTS/OUTPUTS Resolution 20 Bits Logic Family CMOS Logic Coding 2’s Complement ANALOG PERFORMANCE – DAC to Line-out/Headphone Output Output level for full scale input (for AUDVDD, HSVDD = 2.8 V) Output common mode voltage 1.65 Vpp 0.5xHSVDD V 32 Ohm 10 kOhm Output load resistance (on HSL, HSR) - Headphone load 16 - Line load Output load capacitance (on HSL, HSR) - Headphone load 30 1000 pF - Line load 30 150 pF Signal to Noise Ratio (–1dBFS @ 1kHz input and 0dB Gain) - Line and Headphone loads 87 92 dB Total Harmonic Distortion (–1dBFS @ 1kHz input and 0dB Gain) - Line Load -80 - Headphone Load -65 - Headphone Load (16 Ohm) -40 -76 -60 dB dB dB Dynamic Range (measured with -60 dBFS @ 1kHz input, extrapolated to full-scale) - Line Load 88 93 dB - Headphone Load 70 74 dB Interchannel mismatch 0.1 1 dB Left-channel to right-channel crosstalk (@ 1kHz) -90 -80 dB - 6 dB Output Power Level Control Range Output Power Level Control Step -6 3 dB - 1kHz 55 dB - 20kHz 50 dB PSRR Maximum output slope at power up (100 to 220F coupling capacitor) 3 V/s ANALOG PERFORMANCE – Line-in/Microphone Input to Line-out/Headphone Output 83 7524D–MP3–07/07 OVERALL MIN Input level for full scale output - 0dBFS Level @ AUDVDD, HSVDD = 2.8 V and 0 dB gain @ AUDVDD, HSVDD = 2.8 V and 20 dB gain Input common mode voltage Input impedance 7 TYP MAX UNITS 1.65 Vpp 583 mVrms 0.165 Vpp 58.3 mVrms 0.5xAUDVD D V 10 kOhm 85 dB Signal to Noise Ratio -1 dBFS @ 1kHz input and 0 dB gain 81 -21 dBFS @ 1kHz input and 20 dB gain 71 Dynamic Range (extrapolated to full scale level) -60 dBFS @ 1kHz input and 0 dB gain 82 -60 dBFS @ 1kHz input and 20 dB gain 86 dB 72 Total Harmonic Distortion –1dBFS @ 1kHz input and 0 dB gain -80 -76 –1dBFS @ 1kHz input and 20 dB gain -75 -68 dB Interchannel mismatch 0.1 1 dB Left-channel to right-channel crosstalk (@ 1kHz) -90 -80 dB ANALOG PERFORMANCE – Differential mono input amplifier Differential input level for full scale output - 0dBFS Level @ AUDVDD, HSVDD = 2.8 V and 0 dB gain Input common mode voltage 1.65 Vppdif 583 mVrms 0.5xAUDVD D V Input impedance 7 10 kOhm Signal to Noise Ratio (-1 dBFS @ 1kHz input and 0 dB gain) 76 80 dB Total Harmonic Distortion (–1dBFS @ 1kHz input and 0 dB gain) -85 -81 dB ANALOG PERFORMANCE – PA Driver Differential output level for full scale input (for AUDVDD, HSVDD = 3 V) 3.3 Vppdif Output common mode voltage 0.5xHSVDD V Output load 10 Signal to Noise Ratio (–1dBFS @ 1kHz input and 0dB Gain) Total Harmonic Distortion (–1dBFS @ 1kHz input and 0dB Gain) 76 kOhm 30 80 -75 pF dB -71 dB 1.5 nspp MASTER CLOCK Master clock Maximum Long Term Jitter 84 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 OVERALL MIN TYP MAX UNITS DIGITAL FILTER PERFORMANCE Frequency response (10 Hz to 20 kHz) +/- 0.1 dB Deviation from linear phase (10 Hz to 20 kHz) +/- 0.1 deg Passband 0.1 dB corner 0.4535 Fs Stopband 0.5465 Fs Stopband Attenuation 65 dB DE-EMPHASIS FILTER PERFORMANCE (for 44.1kHz Fs) Frequency Gain Pass band 0Hz to 3180Hz Transition band 3180Hz to 10600Hz Stop Band 10600Hz to 20kHz -1dB Logarithm decay -10.45dB Margin 1dB 1dB 1dB Power Performance Current consumption from Audio Analog supply AVDD, HSVDD in power on 9.5 Current consumption from Audio Analog supply AVDD, HSVDD in power down mA 10 µA Power on Settling Time - From full Power Down to Full Power Up (AUDVREF and AUDVCM decoupling capacitors charge) 500 ms - Linein amplifier (Line-in coupling capacitors charge) 50 ms - Driver amplifier (out driver DC blocking capacitors charge) 500 ms 85 7524D–MP3–07/07 Digital Filters Transfer Function Figure 86. Channel Filter Figure 87. De-emphasis Filter 0 -2 -4 Gain (dB) -6 -8 -10 -12 3 4 10 10 Frequency (Hz) 86 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Figure 88. DAC and PA Connection Audio DAC and PA Connection PAINN Battery AUDVSS 3.2V to 5.5V Audio Dac and PA Connection 3V from LDO VDD AUDVBAT C17 C16 CBP AUDVDD VSS 3V from LDO AUDVSS C7 HPP AUDVSS C18 8 Ohm Loud Speaker HPN HSVDD AUDVSS C19 LPHN C15 R1 HSVSS PAINP C9 MONOP AUDVREF C11 MONON C12 R AUDVCM C8 C3 L LINEL Mono AUDVSS Differential Input 32 Ohm mono input (+) AUXP mono input C1 (-) AUXN C6 C4 HSR 32 Ohm C5 Headset or Line Out AUDVSS LINER Stereo Line Input VSS HSL 32 Ohm INGND AUDVSS C10 AUDVSS ESDVSS VSS VSS ESDVSS 87 7524D–MP3–07/07 Table 62. DAC and PA Characteristics Symbol 88 Parameter Typ Unit C1 Capacitance 470 nF C3 Capacitance 470 nF C4 Capacitance 470 nF C5 Capacitance 100 µF C6 Capacitance 100 µF C7 Capacitance 100 nF C8 Capacitance 470 nF C9 Capacitance 100n µF C10 Capacitance 10 µF C11 Capacitance 10 µF C12 Capacitance 470 nF C15 Capacitance 470 nF C16 Capacitance 22 µF C17 Capacitance 100 nF C18 Capacitance 100 nF C19 Capacitance 100 nF R1 Resistor 200 Ω AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 MMC Interface Definition of symbols Table 63. MMC Interface Timing Symbol Definitions Signals Timings Conditions C Clock H High D Data In L Low O Data Out V Valid X No Longer Valid Table 64. MMC Interface AC timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C, CL ≤ 100pF (10 cards) Symbol Waveforms Parameter Min Max Unit TCHCH Clock Period 50 ns TCHCX Clock High Time 10 ns TCLCX Clock Low Time 10 ns TCLCH Clock Rise Time 10 ns TCHCL Clock Fall Time 10 ns TDVCH Input Data Valid to Clock High 3 ns TCHDX Input Data Hold after Clock High 3 ns TCHOX Output Data Hold after Clock High 5 ns TOVCH Output Data Valid to Clock High 5 ns Figure 89. MMC Input-Output Waveforms TCHCH TCHCX TCLCX MCLK TCHCL TCHIX TCLCH TIVCH MCMD Input MDAT Input TCHOX TOVCH MCMD Output MDAT Output 89 7524D–MP3–07/07 Audio Interface Definition of symbols Table 65. Audio Interface Timing Symbol Definitions Signals Conditions C Clock H High O Data Out L Low S Data Select V Valid X No Longer Valid Table 66. Audio Interface AC timings Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C, CL≤ 30pF Symbol Min Max Unit 325.5(1) ns TCHCH Clock Period TCHCX Clock High Time 30 ns TCLCX Clock Low Time 30 ns TCLCH Clock Rise Time 10 ns TCHCL Clock Fall Time 10 ns TCLSV Clock Low to Select Valid 10 ns TCLOV Clock Low to Data Valid 10 ns Note: Waveforms Parameter 1. 32-bit format with Fs= 48 KHz. Figure 90. Audio Interface Waveforms TCHCH TCHCX TCLCX DCLK TCHCL TCLCH TCLSV DSEL Right Left TCLOV DDAT 90 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 External Clock Drive and Logic Level References Definition of symbols Table 67. External Clock Timing Symbol Definitions Signals C Timings Conditions Clock H High L Low X No Longer Valid Table 68. External Clock AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Max Unit TCLCL Clock Period 50 ns TCHCX High Time 10 ns TCLCX Low Time 10 ns TCLCH Rise Time 3 ns TCHCL Fall Time 3 ns Cyclic Ratio in X2 mode 40 TCR Waveforms Min 60 % Figure 91. External Clock Waveform TCLCH VDD - 0.5 VIH1 TCHCX TCLCX VIL 0.45 V TCHCL TCLCL Figure 92. AC Testing Input/Output Waveforms INPUTS VDD - 0.5 0.45 V Note: OUTPUTS 0.7 VDD VIH min 0.3 VDD VIL max 1. During AC testing, all inputs are driven at VDD -0.5 V for a logic 1 and 0.45 V for a logic 0. 2. Timing measurements are made on all outputs at VIH min for a logic 1 and VIL max for a logic 0. Figure 93. Float Waveforms VLOAD VLOAD + 0.1 V VLOAD - 0.1 V Timing Reference Points VOH - 0.1 V VOL + 0.1 V 91 7524D–MP3–07/07 Note: 92 For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loading VOH/VOL level occurs with IOL/IOH= ±20 mA. AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Ordering Information Table Possible order entries Part Number AT83SND2MP3A17FTUL Supply Voltage 3V Temperature Range Industrial & Green Max Frequency Package Packing Product Marking 40 MHz BGA100 Tray 83C51SND2CMP 3A1-ULA RoHS Compliant Firmware Version Yes 2.40 RoHS Compliant Firmware Version Table Obsolete part numbers Part Number Supply Voltage Temperature Range Max Frequency Package Packing Product Marking AT83SND2MP3-7FTIL 3V Industrial 40 MHz BGA100 Tray 83C51SND2C-IL No 2.00 AT83SND2MP3-7FTJL 3V Industrial & ROHS 40 MHz BGA100 Tray 83C51SND2C-JL Yes 2.00 AT83SND2CDVX-7FTIL 3V Industrial 40 MHz BGA100 Tray 83C51SND2C-IL No 2.07 3V Industrial & ROHS 40 MHz BGA100 Tray 83C51SND2C-JL Yes 2.07 AT83SND2CDVX7FTJL 93 7524D–MP3–07/07 Package Information CTBGA100 94 AT83SND2CMP3 7524D–MP3–07/07 AT83SND2CMP3 Document Revision History Changes from 7524A07/05 to 7524B-05/06 1. Added AT83SND2CDVX part number. Changes from 7524B05/06 to 7524C - 06/07 1. Added AT83SND2CMP3A1 part number. Changes from7524C 06/07 to 7524D - 07/07 1. Updated Package drawing, CTBGA100. 95 7524D–MP3–07/07 Table of Contents Features ................................................................................................. 1 Typical Applications ............................................................................. 1 Description ............................................................................................ 2 Block Diagram....................................................................................... 3 Pin Description ...................................................................................... 4 Pinouts ................................................................................................................. 4 Signals................................................................................................................... 5 Internal Pin Structure............................................................................................ 9 Clock Controller .................................................................................. 10 Oscillator ............................................................................................................ 10 PLL ..................................................................................................................... 10 MP3 Decoder ....................................................................................... 12 Decoder .............................................................................................................. 12 Audio Controls ..................................................................................................... 14 Frame Information ............................................................................................... 15 Ancillary Data ..................................................................................................... 15 Audio Output Interface ....................................................................... 16 Description ......................................................................................................... 16 Clock Generator .................................................................................................. 17 Data Converter ................................................................................................... 17 Audio Buffer........................................................................................................ 18 MP3 Buffer ......................................................................................................... 19 Interrupt Request................................................................................................ 19 MP3 Song Playing .............................................................................................. 19 DAC and PA Interface ......................................................................... 21 DAC .................................................................................................................... 21 Power Amplifier ................................................................................................... 39 Audio Supplies and Start-up............................................................................... 40 Universal Serial Bus ........................................................................... 43 Description .......................................................................................................... 44 USB Interrupt System......................................................................................... 49 MultiMedia Card Controller ................................................................ 51 96 AT83SND2CMP3 Card Concept...................................................................................................... 51 Bus Concept ....................................................................................................... 51 Description.......................................................................................................... 56 Clock Generator.................................................................................................. 56 Command Line Controller................................................................................... 58 Data Line Controller............................................................................................. 60 Interrupt ............................................................................................................... 66 Serial I/O Port ...................................................................................... 67 Mode Selection ................................................................................................... 67 Baud Rate Generator.......................................................................................... 67 Synchronous Mode (Mode 0) ............................................................................. 68 Asynchronous Modes (Modes 1, 2 and 3) ........................................................... 70 Multiprocessor Communication (Modes 2 and 3) ............................................... 73 Automatic Address Recognition.......................................................................... 73 Interrupt ............................................................................................................... 75 Keyboard Interface ............................................................................. 76 Description.......................................................................................................... 76 Electrical Characteristics ................................................................... 77 Absolute Maximum Rating.................................................................................. 77 DC Characteristics.............................................................................................. 77 Ordering Information .......................................................................... 93 Package Information .......................................................................... 94 CTBGA100 ......................................................................................................... 94 Document Revision History ............................................................... 95 Changes from 7524A-07/05 to 7524B-05/06 ...................................................... 95 Changes from 7524B-05/06 to 7524C - 06/07.................................................... 95 Changes from7524C - 06/07 to 7524D - 07/07................................................... 95 97 7524D–MP3–07/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. ©2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, are registered trademarks, or the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 7524D–MP3–07/07