Document 581-1 Shielded Power Inductors – LPS5030 • Very low DCR; excellent current handling • 4.9 × 4.9 mm footprint; less than 3 mm tall Designer’s Kit C420 contains 3 each of all values Core material Ferrite Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over silver. Other terminations available at additional cost. Weight 226 – 244 mg Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide, 0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Isat (A)5 Irms (A)6 DCR SRF Inductance2 max3 typ4 10% 20% 30% 20°C 40°C Part number1 ±20% (µH) (Ohms) (MHz) drop drop drop rise rise LPS5030-901MR_ LPS5030-122MR_ LPS5030-172MR_ LPS5030-222MR_ LPS5030-332MR_ LPS5030-472MR_ LPS5030-562MR_ LPS5030-682MR_ LPS5030-822MR_ LPS5030-103MR_ LPS5030-123MR_ LPS5030-153MR_ LPS5030-183MR_ LPS5030-223MR_ LPS5030-333MR_ LPS5030-473MR_ LPS5030-683MR_ LPS5030-823MR_ LPS5030-104MR_ LPS5030-124MR_ LPS5030-154MR_ LPS5030-224MR_ LPS5030-334MR_ LPS5030-474MR_ LPS5030-564MR_ LPS5030-684MR_ LPS5030-105MR_ LPS5030-155MR_ LPS5030-185MR_ LPS5030-225MR_ LPS5030-335MR_ LPS5030-475MR_ 0.90 1.2 1.7 2.2 3.3 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 33.0 47.0 68.0 82.0 100 120 150 220 330 470 560 680 1000 1500 1800 2200 3300 4700 0.040 0.043 0.051 0.057 0.066 0.083 0.089 0.099 0.125 0.127 0.155 0.160 0.170 0.190 0.260 0.330 0.440 0.470 0.600 0.800 0.860 1.35 1.80 2.80 3.20 3.80 5.10 7.60 10.0 11.0 19.5 26.0 250 210 190 168 125 84 70 56 45 30 24 32 27 24 19 16 12 11 10 9 7.5 6.0 5.0 4.0 3.6 3.0 2.5 2.0 1.8 1.6 1.3 1.1 3.8 3.5 3.0 2.9 2.3 1.9 1.8 1.6 1.6 1.4 1.3 0.80 0.80 0.70 0.60 0.50 0.40 0.38 0.27 0.26 0.22 0.21 0.155 0.117 0.110 0.100 0.100 0.068 0.069 0.063 0.056 0.049 4.0 3.6 3.2 3.1 2.5 2.0 1.8 1.7 1.7 1.4 1.4 0.90 0.82 0.75 0.63 0.53 0.43 0.40 0.31 0.29 0.25 0.235 0.155 0.134 0.130 0.120 0.110 0.080 0.081 0.074 0.063 0.056 4.1 3.7 3.3 3.2 2.6 2.0 1.9 1.7 1.7 1.4 1.4 0.90 0.87 0.78 0.64 0.55 0.44 0.40 0.32 0.30 0.263 0.245 0.200 0.146 0.140 0.126 0.110 0.089 0.086 0.080 0.067 0.059 2.10 2.00 1.90 1.60 1.40 1.30 1.25 1.20 1.10 1.00 0.95 0.92 0.90 0.88 0.85 0.75 0.65 0.60 0.55 0.45 0.42 0.36 0.32 0.28 0.23 0.20 0.18 0.15 0.13 0.10 0.090 0.080 2.80 2.65 2.50 2.15 1.80 1.75 1.65 1.60 1.55 1.50 1.40 1.40 1.30 1.25 1.20 1.00 0.900 0.830 0.750 0.660 0.570 0.500 0.420 0.370 0.320 0.290 0.250 0.210 0.170 0.150 0.125 0.110 1. Please specify termination and packaging codes: LPS5030-105MRC Termination: R = RoHS compliant matte tin over nickel over silver. Special order, added cost: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (750 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP 4192A impedance analyzer or equivalent. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information. 6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 581-1 Revised 09/02/15 Document 581-2 Shielded Power Inductors – LPS5030 Series Typical L vs Frequency Typical L vs Current 10000 10000 3300 µH 3300 µH 1000 µH 330 µH 100 µH 100 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 33 µH 10 µH 10 330 µH 100 µH 100 33 µH 10 µH 10 3.3 µH 3.3 µH 1 0.01 1 0.1 10 Frequency (MHz) 0.1 Current (A) 1 10 NOTE NEW PART ORIENTATION Parts are rotated 90° in the packaging tape compared to previous versions of this product. 0.189 ±0.003* 4,80 ±0,076 Winding direction NEW 0.114 ±0.004 * 2,9 ±0,1 OLD 123 Internal code 123 123 Dash number 0.01 Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide, 0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth 0.189 ±0.003* 4,80 ±0,076 XXX X 1 123 123 123 Recommended Land Pattern 0.060 1,50 0.134 3,40 0.039 typ 1,00 0.217 5,51 0.0665 1,689 0.039 typ 1,00 are of the case not including * Dimensions the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch / 0,13 mm). 0.134 3,40 0.134 3,40 0.060 1,52 0.134 3,40 0.217 5,51 Dimensions are in inches mm Document 581-2 Revised 09/02/15