E32D1 Series E32D1 • RoHS Compliant (Pb-Free) • PECL Output Oscillators • 3.3V supply voltage • Ceramic 6-pad SMD Package • Stability to ±25ppm • Tri-State Output • Complementary Output • Available on Tape and Reel H L W 2.0 7.0 5.0 OSCILLATOR ELECTRICAL SPECIFICATIONS 50, 51.84, 52, 52.08, 54, 57.1429, 61.44, 63.36, 65.536, 76.8, 77.76, 100, 104, 106.25, 125, 126.72, 128, 153.6, 155.52, 156.25, 159.375, 161.1328, 166.6286, 167.3315, 184.32, 186.666MHz Operating Temperature Range 0°C to 70°C -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 3.3VDC ±5% Input Current 100mA Maximum With Load Frequency Tolerance / Stability Inclusive of all conditions: Calibration Tolerance at 25°C, ±50ppm or ±25ppm Maximum Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, 1st Year Aging, Shock, and Vibration Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 1.5 nSeconds Maximum 20% to 80% of waveform Duty Cycle 50 ±10(%) at 50% of waveform 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Control Voltage (VC) 1.65VDC ±1.65VDC Test Conditions for Frequency Deviation Control Voltage Range (VCR) 0.0VDC to VCC +0.5VDC Frequency Deviation ±75ppm Minimum Inclusive of Operating Temperature Range, Supply Voltage Change, and Output Load Change Linearity 20%, 15%, or 10% Maximum Transfer Function Positive Transfer Characteristic Modulation Bandwidth (MBW) 10kHz Minimum Measured at -3dB with Contol Voltage of +1.65VDC Input Impedance (ZI) 50kOhms Typical Typical Phase Noise (Fo = 155.520MHz) at 10Hz Offset -55dBc/Hz -90dBc/Hz at 100Hz Offset -120dBc/Hz at 1kHz Offset -140dBc/Hz at 10kHz Offset -145dBc/Hz at 100kHz Offset -148dBc/Hz at 1MHz Offset Logic Control/Additional Output Tri-State Enable Low / Complementary Output Tri-State Input Voltage Disables Outputs: High Impedance VIH of 70% of VCC Minimum Enables Output No Connection Enables Output VIL of 30% of VCC Maximum RMS Phase Jitter 0.4pSec Typical, 1pSec Maximum FJ = 12kHz to 20MHz Accumulated Period Jitter (tacc) 4pSec Typical, 5pSec Maximum Sigma of Total Jitter Distribution Period Jitter (trj) 3pSec Typical, 5pSec Maximum Sigma of Random Jitter Period Jitter (trms) 3pSec Typical, 5pSec Maximum Sigma of Total Jitter Distribution Period Jitter (tdj) 4pSec Typical, 10pSec Maximum Deterministic Jitter Period Jitter (tp-p) 27pSec Typical, 40pSec Maximum Peak to Peak of Jitter Distribution Start Up Time 10 mSeconds Maximum Frequency Range (MHz) MANUFACTURER CATEGORY ECLIPTEK CORP. OSCILLATOR SERIES PACKAGE VOLTAGE CLASS REV.DATE E32D1 CERAMIC 3.3V OS3Y 01/09 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice. PART NUMBERING GUIDE E32D1 E E A 2 K - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Bulk TR=Tape and Reel (Standard) FREQUENCY DEVIATION E=±75ppm Minimum LOGIC CONTROL / ADDITIONAL OUTPUT K=Tri-State (Enable Low) / Complementary Output LINEARITY A=20% Maximum B=15% Maximum C=10% Maximum DUTY CYCLE 1=50% ±10% 2=50% ±5% FREQUENCY MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Pin 1: Voltage Control Pin 2: Tri-State Pin 3: Case Ground Pin 4: Output Pin 5: Complementary Output Pin 6: Supply Voltage Tolerances= +0.1 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE A B C D E 16±.3-.1 7.5±.1 6.75±.1 4 ±.1 2±.1 F G H J K 8±.1 B0* 1.5 +.1-0 A0* .3 ±.05 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1,000 REEL L K0* R S T U V 2.5 MIN 10 MIN 22.4 MAX 360 MAX 16.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Line 1: ECLIPTEK Characteristic Specification Fine Leak Test Gross Leak Test Mechanical Shock Vibration Solderability Temperature Cycling Resistance to Soldering Heat Resistance to Solvents MIL-STD-883, Method 1014, Condition A MIL-STD-883, Method 1014, Condition C MIL-STD-202, Method 213, Condition C MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS ECLIPTEK CORP. OSCILLATOR E32D1 CERAMIC 3.3V OS3Y 800-ECLIPTEK www.ecliptek.com for latest revision REV.DATE 01/09 Specifications subject to change without notice.