PD - 94436C
IRF2804
IRF2804S
IRF2804L
AUTOMOTIVE MOSFET
HEXFET® Power MOSFET
Features
l
l
l
l
l
Advanced Process Technology
Ultra Low On-Resistance
175°C Operating Temperature
Fast Switching
Repetitive Avalanche Allowed up to Tjmax
D
VDSS = 40V
RDS(on) = 2.0mΩ
G
Description
ID = 75A
S
Specifically designed for Automotive applications,
this HEXFET® Power MOSFET utilizes the latest
processing techniques to achieve extremely low
on-resistance per silicon area. Additional features
of this design are a 175°C junction operating
temperature, fast switching speed and improved
repetitive avalanche rating . These features combine to make this design an extremely efficient
and reliable device for use in Automotive applications and a wide variety of other applications.
D2Pak
IRF2804S
TO-220AB
IRF2804
TO-262
IRF2804L
Absolute Maximum Ratings
Parameter
Max.
Units
ID @ TC = 25°C
Continuous Drain Current, VGS @ 10V (Silicon Limited)
280
A
ID @ TC = 100°C
Continuous Drain Current, VGS @ 10V (See Fig. 9)
200
ID @ TC = 25°C
Continuous Drain Current, VGS @ 10V (Package Limited)
IDM
Pulsed Drain Current
PD @TC = 25°C
Maximum Power Dissipation
330
W
VGS
Linear Derating Factor
Gate-to-Source Voltage
2.2
± 20
W/°C
V
670
mJ
EAS
75
c
1080
EAS (tested)
Single Pulse Avalanche Energy (Thermally Limited)
Single Pulse Avalanche Energy Tested Value
IAR
Avalanche Current
EAR
Repetitive Avalanche Energy
TJ
Operating Junction and
TSTG
Storage Temperature Range
i
c
d
1160
See Fig.12a,12b,15,16
h
A
mJ
°C
-55 to + 175
Soldering Temperature, for 10 seconds
300 (1.6mm from case )
Mounting torque, 6-32 or M3 screw
10 lbf•in (1.1N•m)
Thermal Resistance
Parameter
RθJC
RθCS
Junction-to-Case
Case-to-Sink, Flat, Greased Surface
RθJA
Junction-to-Ambient
RθJA
Junction-to-Ambient (PCB Mount, steady state)
j
Typ.
Max.
Units
–––
0.45
°C/W
0.50
–––
–––
62
–––
40
HEXFET® is a registered trademark of International Rectifier.
www.irf.com
1
08/27/03
IRF2804/S/L
Static @ TJ = 25°C (unless otherwise specified)
Parameter
V(BR)DSS
∆ΒVDSS/∆TJ
Drain-to-Source Breakdown Voltage
RDS(on) SMD
RDS(on) TO-220 Static Drain-to-Source On-Resistance
VGS(th)
Gate Threshold Voltage
gfs
IDSS
IGSS
Min. Typ. Max. Units
V
Conditions
40
–––
–––
VGS = 0V, ID = 250µA
Breakdown Voltage Temp. Coefficient
–––
0.031
–––
V/°C Reference to 25°C, ID = 1mA
Static Drain-to-Source On-Resistance
–––
1.5
2.0
mΩ
–––
1.8
2.3
2.0
–––
4.0
f
= 75A f
VGS = 10V, ID = 75A
VGS = 10V, ID
V
VDS = VGS, ID = 250µA
Forward Transconductance
130
–––
–––
S
VDS = 10V, ID = 75A
Drain-to-Source Leakage Current
–––
–––
20
µA
VDS = 40V, VGS = 0V
–––
–––
250
Gate-to-Source Forward Leakage
–––
–––
200
nA
VGS = 20V
nC
ID = 75A
VDS = 40V, VGS = 0V, TJ = 125°C
Gate-to-Source Reverse Leakage
–––
–––
-200
Qg
Total Gate Charge
–––
160
240
VGS = -20V
Qgs
Gate-to-Source Charge
–––
41
62
VDS = 32V
Qgd
Gate-to-Drain ("Miller") Charge
–––
66
99
VGS = 10V
td(on)
Turn-On Delay Time
–––
13
–––
tr
Rise Time
–––
120
–––
ID = 75A
td(off)
Turn-Off Delay Time
–––
130
–––
RG = 2.5Ω
tf
Fall Time
–––
130
–––
LD
Internal Drain Inductance
–––
4.5
–––
LS
Internal Source Inductance
–––
7.5
–––
6mm (0.25in.)
from package
and center of die contact
VGS = 0V
ns
VGS = 10V
nH
f
VDD = 20V
f
Between lead,
D
G
S
Ciss
Input Capacitance
–––
6450
–––
Coss
Output Capacitance
–––
1690
–––
Crss
Reverse Transfer Capacitance
–––
840
–––
ƒ = 1.0MHz, See Fig. 5
Coss
Output Capacitance
–––
5350
–––
VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz
Coss
Output Capacitance
–––
1520
–––
VGS = 0V, VDS = 32V, ƒ = 1.0MHz
Coss eff.
Effective Output Capacitance
–––
2210
–––
VGS = 0V, VDS = 0V to 32V
pF
VDS = 25V
Diode Characteristics
Parameter
Min. Typ. Max. Units
Conditions
IS
Continuous Source Current
–––
–––
280
ISM
(Body Diode)
Pulsed Source Current
–––
–––
1080
VSD
(Body Diode)
Diode Forward Voltage
–––
–––
1.3
V
p-n junction diode.
TJ = 25°C, IS = 75A, VGS = 0V
trr
Qrr
Reverse Recovery Time
Reverse Recovery Charge
–––
–––
56
67
84
100
ns
nC
TJ = 25°C, IF = 75A, VDD = 20V
di/dt = 100A/µs
ton
Forward Turn-On Time
c
A
D
showing the
integral reverse
G
S
f
f
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11).
Limited by TJmax, starting TJ = 25°C,
L=0.24mH, RG = 25Ω, IAS = 75A, VGS =10V.
Part not recommended for use above this value.
ISD ≤ 75A, di/dt ≤ 220A/µs, VDD ≤ V(BR)DSS,
TJ ≤ 175°C.
Pulse width ≤ 1.0ms; duty cycle ≤ 2%.
Coss eff. is a fixed capacitance that gives the same
charging time as Coss while VDS is rising from 0 to 80%
VDSS.
2
MOSFET symbol
Limited by T Jmax , see Fig.12a, 12b, 15, 16 for typical repetitive
avalanche performance.
This value determined from sample failure population. 100%
tested to this value in production.
This is applied to D 2Pak, when mounted on 1" square PCB
( FR-4 or G-10 Material ). For recommended footprint and
soldering techniques refer to application note #AN-994.
Max R DS(on) for D2Pak and TO-262 (SMD) devices.
www.irf.com
IRF2804/S/L
10000
10000
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM 4.5V
1000
TOP
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
100
10
4.5V
1000
VGS
V
GS
15V
15V
10V
10V
8.0V
8.0V
7.0V
7.0V
6.0V
6.0V
5.5V
5.5V
5.0V
BOTTOM 5.0V
4.5V
BOTTOM 4.5V
100
4.5V
20µs PULSE WIDTH
Tj = 25°C
20µs PULSE WIDTH
Tj = 175°C
1
10
0.1
1
10
100
0.1
VDS, Drain-to-Source Voltage (V)
10
100
VDS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
Fig 2. Typical Output Characteristics
1000
300
G fs , Forward Transconductance ( S)
ID, Drain-to-Source Current (Α)
1
T J = 175°C
100
T J = 25°C
10
VDS = 10V
20µs PULSE WIDTH
1
250
T J = 25°C
200
T J = 175°C
150
100
50
VDS = 10V
20µs PULSE WIDTH
0
4.0
5.0
6.0
7.0
8.0
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
www.irf.com
9.0
0
40
80
120
160
200
ID, Drain-to-Source Current (A)
Fig 4. Typical Forward Transconductance
vs. Drain Current
3
IRF2804/S/L
12000
20
10000
VGS , Gate-to-Source Voltage (V)
VGS = 0V,
f = 1 MHZ
Ciss = Cgs + Cgd, Cds SHORTED
Crss = Cgd
C, Capacitance (pF)
Coss = Cds + Cgd
8000
Ciss
6000
4000
Coss
2000
Crss
VDS= 32V
VDS= 20V
VDS= 8.0V
16
12
8
4
0
0
1
ID= 75A
10
0
100
120
160
200
240
Fig 6. Typical Gate Charge vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance vs.
Drain-to-Source Voltage
10000
1000.0
OPERATION IN THIS AREA
LIMITED BY RDS(on)
ID, Drain-to-Source Current (A)
ISD, Reverse Drain Current (A)
80
Q G Total Gate Charge (nC)
VDS, Drain-to-Source Voltage (V)
T J = 175°C
100.0
10.0
1.0
T J = 25°C
VGS = 0V
0.1
0.2
0.6
1.0
1.4
1.8
VSD, Source-toDrain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
40
1000
100
1msec
10
1
2.2
100µsec
Tc = 25°C
Tj = 175°C
Single Pulse
0
1
10msec
10
100
1000
VDS , Drain-toSource Voltage (V)
Fig 8. Maximum Safe Operating Area
www.irf.com
IRF2804/S/L
2.0
LIMITED BY PACKAGE
ID , Drain Current (A)
250
200
150
100
50
0
ID = 75A
VGS = 10V
1.5
(Normalized)
RDS(on) , Drain-to-Source On Resistance
300
1.0
0.5
25
50
75
100
125
150
175
-60 -40 -20
T C , Case Temperature (°C)
0
20 40 60 80 100 120 140 160 180
TJ , Junction Temperature (°C)
Fig 10. Normalized On-Resistance
vs. Temperature
Fig 9. Maximum Drain Current vs.
Case Temperature
Thermal Response ( Z thJC )
1
D = 0.50
0.20
0.1
0.10
0.05
0.02
0.01
0.01
SINGLE PULSE
( THERMAL RESPONSE )
0.001
1E-006
1E-005
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
IRF2804/S/L
1600
DRIVER
L
VDS
D.U.T
RG
+
V
- DD
IAS
VGS
20V
A
0.01Ω
tp
Fig 12a. Unclamped Inductive Test Circuit
V(BR)DSS
tp
EAS, Single Pulse Avalanche Energy (mJ)
15V
ID
31A
53A
BOTTOM 75A
TOP
1200
800
400
0
25
50
75
100
125
150
175
Starting TJ , Junction Temperature (°C)
I AS
Fig 12c. Maximum Avalanche Energy
vs. Drain Current
Fig 12b. Unclamped Inductive Waveforms
QG
10 V
QGS
QGD
VG
Charge
Fig 13a. Basic Gate Charge Waveform
Current Regulator
Same Type as D.U.T.
50KΩ
12V
.2µF
.3µF
D.U.T.
+
V
- DS
VGS(th) Gate threshold Voltage (V)
4.0
ID = 250µA
3.0
2.0
1.0
-75 -50 -25
VGS
0
25
50
75
100 125 150 175
T J , Temperature ( °C )
3mA
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
6
Fig 14. Threshold Voltage vs. Temperature
www.irf.com
IRF2804/S/L
10000
Avalanche Current (A)
Duty Cycle = Single Pulse
1000
Allowed avalanche Current vs
avalanche pulsewidth, tav
assuming ∆ Tj = 25°C due to
avalanche losses. Note: In no
case should Tj be allowed to
exceed Tjmax
0.01
100
0.05
0.10
10
1
1.0E-07
1.0E-06
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
tav (sec)
Fig 15. Typical Avalanche Current Vs.Pulsewidth
EAR , Avalanche Energy (mJ)
800
TOP
Single Pulse
BOTTOM 10% Duty Cycle
ID = 75A
600
400
200
0
25
50
75
100
125
150
Starting T J , Junction Temperature (°C)
Fig 16. Maximum Avalanche Energy
vs. Temperature
www.irf.com
Notes on Repetitive Avalanche Curves , Figures 15, 16:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a
temperature far in excess of T jmax. This is validated for
every part type.
2. Safe operation in Avalanche is allowed as long asT jmax is
not exceeded.
3. Equation below based on circuit and waveforms shown in
Figures 12a, 12b.
4. PD (ave) = Average power dissipation per single
avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for
voltage increase during avalanche).
6. Iav = Allowable avalanche current.
7. ∆T = Allowable rise in junction temperature, not to exceed
Tjmax (assumed as 25°C in Figure 15, 16).
tav = Average time in avalanche.
175
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav ) = Transient thermal resistance, see figure 11)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
7
IRF2804/S/L
D.U.T
Driver Gate Drive
+
+
-
P.W.
D.U.T. ISD Waveform
Reverse
Recovery
Current
+
V DD
• dv/dt controlled by RG
• Driver same type as D.U.T.
• I SD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
P.W.
Period
*
RG
D=
VGS=10V
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
-
Period
+
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
-
Body Diode
VDD
Forward Drop
Inductor Curent
ISD
Ripple ≤ 5%
*
VGS = 5V for Logic Level Devices
Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
V DS
V GS
RG
RD
D.U.T.
+
-V DD
10V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
Fig 18a. Switching Time Test Circuit
VDS
90%
10%
VGS
td(on)
tr
t d(off)
tf
Fig 18b. Switching Time Waveforms
8
www.irf.com
IRF2804/S/L
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
2.87 (.113)
2.62 (.103)
10.54 (.415)
10.29 (.405)
-B-
3.78 (.149)
3.54 (.139)
4.69 (.185)
4.20 (.165)
-A-
1.32 (.052)
1.22 (.048)
6.47 (.255)
6.10 (.240)
4
15.24 (.600)
14.84 (.584)
1.15 (.045)
MIN
1
2
3
14.09 (.555)
13.47 (.530)
4.06 (.160)
3.55 (.140)
3X
1.40 (.055)
3X
1.15 (.045)
LEAD ASSIGNMENTS
1 - GATE
2 - DRAIN
3 - SOURCE
4 - DRAIN
0.93 (.037)
0.69 (.027)
0.36 (.014)
3X
M
B A M
0.55 (.022)
0.46 (.018)
2.92 (.115)
2.64 (.104)
2.54 (.100)
2X
NOTES:
1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982.
2 CONTROLLING DIMENSION : INCH
3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB.
4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS.
TO-220AB Part Marking Information
EXAMPLE : THIS IS AN IRF1010
WITH ASSEMBLY
LOT CODE 9B1M
A
INTERNATIONAL
RECTIFIER
LOGO
ASSEMBLY
LOT CODE
www.irf.com
PART NUMBER
IRF1010
9246
9B 1M
DATE CODE
(YYWW)
YY = YEAR
WW = WEEK
9
IRF2804/S/L
D2Pak Package Outline
Dimensions are shown in millimeters (inches)
D2Pak Part Marking Information
T HIS IS AN IRF530S WIT H
LOT CODE 8024
ASS EMBLED ON WW 02, 2000
IN T HE ASS EMBLY LINE "L"
INT ERNAT IONAL
RECT IFIER
LOGO
ASS EMBLY
LOT CODE
10
PART NUMBER
F 530S
DAT E CODE
YEAR 0 = 2000
WEEK 02
LINE L
www.irf.com
IRF2804/S/L
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
IGBT
1- GATE
2- COLLECTOR
3- EMITTER
TO-262 Part Marking Information
EXAMPLE: T HIS IS AN IRL3103L
LOT CODE 1789
ASS EMBLED ON WW 19, 1997
IN THE ASS EMBLY LINE "C"
INT ERNATIONAL
RECTIFIER
LOGO
AS SEMBLY
LOT CODE
www.irf.com
PART NUMBER
DATE CODE
YEAR 7 = 1997
WEEK 19
LINE C
11
IRF2804/S/L
D2Pak Tape & Reel Information
Dimensions are shown in millimeters (inches)
TRR
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
FEED DIRECTION 1.85 (.073)
1.65 (.065)
1.60 (.063)
1.50 (.059)
11.60 (.457)
11.40 (.449)
0.368 (.0145)
0.342 (.0135)
15.42 (.609)
15.22 (.601)
24.30 (.957)
23.90 (.941)
TRL
10.90 (.429)
10.70 (.421)
1.75 (.069)
1.25 (.049)
4.72 (.136)
4.52 (.178)
16.10 (.634)
15.90 (.626)
FEED DIRECTION
13.50 (.532)
12.80 (.504)
27.40 (1.079)
23.90 (.941)
4
330.00
(14.173)
MAX.
NOTES :
1. COMFORMS TO EIA-418.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION MEASURED @ HUB.
4. INCLUDES FLANGE DISTORTION @ OUTER EDGE.
60.00 (2.362)
MIN.
26.40 (1.039)
24.40 (.961)
3
30.40 (1.197)
MAX.
4
TO-220AB package is not recommended for Surface Mount Application.
Data and specifications subject to change without notice.
This product has been designed and qualified for the Automotive [Q101] market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 08/03
12
www.irf.com
Note: For the most current drawings please refer to the IR website at:
http://www.irf.com/package/