IDT ICS9DB202CF Pci express jitter attenuator Datasheet

ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
GENERAL DESCRIPTION
FEATURES
The ICS9DB202 is a high perfromance 1-to-2
Differential-to-HCSL Jitter Attenuator designed for
use in PCI Express™ systems. In some PCI
Express™ systems, such as those found in desktop
PCs, the PCI Express™ clocks are generated from
a low bandwidth, high phase noise PLL frequency synthesizer.
In these systems, a jitter-attenuating device may be necessary
in order to reduce high frequency random and deterministic
jitter components from the PLL synthesizer and from the system
board. The ICS9DB202 has two PLL bandwidth modes. In low
bandwidth mode, the PLL loop bandwidth is 500kHz. This setting
offers the best jitter attenuation and is still high enough to pass
a triangular input spread spectrum profile. In high bandwidth
mode, the PLL bandwidth is at 1MHz and allows the PLL to
pass more spread spectrum modulation.
• Two 0.7V current mode differential HCSL output pairs
For serdes which have x10 reference multipliers instead of x12.5
multipliers, each of the two PCI Express™ outputs (PCIEX0:1)
can be set for 125MHz instead of 100MHz by configuring the
appropriate frequency select pins (FS0:1).
• 3.3V operating supply
ICS
• One differential clock input
HiPerClockS™
• CLK and nCLK supports the following input types:
LVPECL, LVDS, LVHSTL, SSTL, HCSL
• Maximum output frequency: 140MHz
• Input frequency range: 90MHz - 140MHz
• VCO range: 450MHz - 700MHz
• Output skew: 110ps (maximum)
• Cycle-to-cycle jitter: 110ps (maximum)
• RMS phase jitter @ 100MHz, (1.5MHz - 22MHz):
2.42ps (typical)
• 0°C to 70°C ambient operating temperature
• Available in both standard and lead-free RoHS compliant
packages
BLOCK DIAGRAM
IREF
• Industrial temperature information available upon request
1 HiZ
0 Enabled
nOE0
nCLK
CLK
PIN ASSIGNMENT
Current
Set
+
Phase
Detector
0
Loop
Filter
VCO
0 ÷4
1 ÷5
PCIEXT0
nPCIEXC0
1
0
FS1
20
19
18
17
16
15
14
13
12
11
VDDA
BYPASS
IREF
FS1
VDD
GND
PCIEXT1
PCIEXC1
VDD
nOE1
ICS9DB202
Internal Feedback
0 ÷5
1 ÷4
1
2
3
4
5
6
7
8
9
10
20-Lead TSSOP
6.50mm x 4.40mm x 0.92
package body
G Package
Top View
FS0
÷5
PLL_BW
CLK
nCLK
FS0
VDD
GND
PCIEXT0
PCIEXC0
VDD
nOE0
1
PCIEXT1
nPCIEXC1
ICS9DB202
20-Lead, 209-MIL SSOP
5.30mm x 7.20mm x 1.75mm
body package
F Package
Top View
BYPASS
nOE1
1 HiZ
0 Enabled
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
1
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
TABLE 1. PIN DESCRIPTIONS
Number
Name
1
PLL_BW
Input
Type
2
CLK
Input
3
nCLK
Input
Pullup
Description
Selects PLL Bandwidth input. LVCMOS/LVTTL interface levels.
Pulldown Non-inver ting differential clock input.
Pullup/
Inver ting differential clock input. VDD/2 default when left floating.
Pulldown
Pullup Frequency select pin. LVCMOS/LVTTL interface levels.
4
FS0
Input
5, 9, 12, 16
VDD
Power
Core supply pins.
6, 15
GND
PCIEXT0,
PCIEXC0
Power
Power supply ground.
Output
Differential output pairs. HCSL interface levels.
7, 8
10, 11
nOE0, nOE1
Input
17
PCIEXC1,
PCIEXT1
FS1
18
IREF
Input
19
BYPASS
Power
20
VDDA
Power
13, 14
Pulldown
Output
Input
Output enable. When HIGH, forces outputs to HiZ state.
When LOW, enables outputs. LVCMOS/LVTTL interface levels.
Differential output pairs. HCSL interface levels.
Pulldown Frequency select pin. LVCMOS/LVTTL interface levels.
A fixed precision resistor (475Ω) from this pin to ground provides a
reference current used for differential current-mode PCIEX clock outputs.
BYPASS pin. When HIGH. bypass mode, when LOW, PLL mode.
Pulldown
LVCMOS/LVTTL interface levels.
Analog supply pin. Requires 24Ω series resistor.
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
TABLE 2. PIN CHARACTERISTICS
Symbol
Parameter
Test Conditions
Minimum
Typical
Maximum
Units
CIN
Input Capacitance
4
pF
RPULLUP
Input Pullup Resistor
51
kΩ
RPULLDOWN
Input Pulldown Resistor
51
kΩ
TABLE 3A. RATIO OF OUTPUT FREQUENCY TO
INPUT FREQUENCY FUNCTION TABLE, FS0
TABLE 3B. RATIO OF OUTPUT FREQUENCY TO
INPUT FREQUENCY FUNCTION TABLE, FS1
Inputs
Outputs
Inputs
Outputs
FS0
PCIEX0
FS1
PCIEX1
0
5/4
0
1
1
1
1
5/4
TABLE 3D. OUTPUT ENABLE
FUNCTION TABLE, NOE0
TABLE 3E. OUTPUT ENABLE
FUNCTION TABLE, NOE1
TABLE 3C. BYPASS TABLE
Inputs
BYPASS
0
1
Mode
PLL Mode
Bypass Mode
(output = inputs)
TABLE 3F. PLL BANDWIDTH TABLE
Inputs
Outputs
Inputs
Outputs
Inputs
nOE0
PCIEX0
nOE1
PCIEX1
PLL_BW
0
Enabled
0
Enabled
0
500kHz
1
HiZ
1
HiZ
1
1MHz
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
2
Bandwidth
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VDD
4.6V
Inputs, VI
-0.5V to VDD + 0.5 V
Outputs, VO
-0.5V to VDD + 0.5V
NOTE: Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the
device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond
those listed in the DC Characteristics or AC Characteristics is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
Package Thermal Impedance, θJA
20 Lead TSSOP
73.2°C/W (0 lfpm)
20 Lead SSOP
80.8°C/W (0 lfpm)
-65°C to 150°C
Storage Temperature, TSTG
TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDA = 3.3V±5%, TA = 0°C TO 70°C, RREF = 475Ω
Symbol
Parameter
Minimum
Typical
Maximum
Units
VDD
Core Supply Voltage
Test Conditions
3.135
3. 3
3.465
V
3.135
3. 3
VDDA
Analog Supply Voltage
3.465
V
IDD
Power Supply Current
112
mA
IDDA
Analog Supply Current
22
mA
TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VDD = VDDA = 3.3V±5%, TA = 0°C TO 70°C
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIH
IIL
Input High Current
Input Low Current
Test Conditions
BYPASS,
nOE0, nOE1, FS1
FS0, PLL_BW
BYPASS,
nOE0, nOE1, FS1
FS0, PLL_BW
Minimum
Maximum
Units
2
Typical
VDD + 0.3
mV
-0.3
0.8
mV
150
µA
VDD = VIN = 3.465V
5
VDD = 3.465V, VIN = 0V
-5
µA
-150
TABLE 4C. DIFFERENTIAL DC CHARACTERISTICS, VDD = VDDA = 3.3V±5%, TA = 0°C TO 70°C, RREF = 475Ω
Symbol
Parameter
IIH
Input High Current
CLK, nCLK
VDD = VIN = 3.465V
Test Conditions
IIL
Input Low Current
CLK, nCLK
VDD = 3.465V, VIN = 0V
VPP
Peak-to-Peak Input Voltage
Minimum
Typical
0.15
VCMR
Common Mode Input Voltage; NOTE 1, 2
GND + 0.5
NOTE 1: Common mode voltage is defined as VIH.
NOTE 2: For single ended applications, the maximum input voltage for CLK, nCLK is VDD + 0.3V.
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
3
Maximum
Units
150
µA
150
µA
1.3
V
VDD - 0.85
V
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
TABLE 4D. HCSL DC CHARACTERISTICS, VDD = VDDA = 3.3V±5%, TA = 0°C TO 70°C, RREF = 475Ω
Symbol
Parameter
IOH
Output Current
Test Conditions
VOH
Output High Voltage
VOL
Output Low Voltage
IOZ
High Impedance Leakage Current
VOX
Output Crossover Voltage
Minimum
Typical
Maximum
Units
12
14
16
mA
780
mV
65
mV
-10
10
µA
250
550
mV
Maximum
Units
140
MHz
610
TABLE 5. AC CHARACTERISTICS, VDD = VDDA = 3.3V±5%, TA = 0°C TO 70°C, RREF = 475Ω
Symbol
Parameter
fMAX
Output Frequency
tsk(o)
Output Skew; NOTE 1, 2
tjit(cc)
tjit(Ø)
tR / tF
Cycle-to-Cycle Jitter
RMS Phase Jitter
(Random); NOTE 3
Output Rise/Fall Time
Test Conditions
Minimum
Typical
110
ps
Outputs @ Different Frequencies
50
110
ps
Outputs @ Same Frequencies
50
ps
Integration Range: 1.5MHz - 22MHz
20% to 80%
2.42
300
o dc
Output Duty Cycle
48
NOTE 1: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Please refer to the Phase Noise Plot following this section.
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
4
ps
1100
ps
52
%
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
TYPICAL PHASE NOISE AT 100MHZ
➤
0
-10
PCI Express™ Filter
-20
-30
100MHz
-40
RMS Phase Jitter (Random)
1.5MHz to 22MHz = 2.42ps (typical)
-70
-80
-90
-100
Raw Phase Noise Data
-110
-120
➤
NOISE POWER dBc
Hz
-50
-60
-130
-140
➤
-150
-160
Phase Noise Result by adding
PCI Express™ Filter to raw data
-170
-180
-190
1k
10k
100k
1M
10M
100M
OFFSET FREQUENCY (HZ)
The illustrated phase noise plot was taken using a low phase
noise signal generator, the noise floor of the signal generator is
less than that of the device under test.
Due to the tracking ability of a PLL, it will track the input signal up
to its loop bandwidth. Therefore, if the input phase noise is greater
than that of the PLL, it will increase the output phase noise
performance of the device. It is recommended that the phase
noise performance of the input is verified in order to achieve the
above phase noise performance.
Using this configuration allows one to see the true spectral purity
or phase noise performance of the PLL in the device under test.
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
5
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
PARAMETER MEASUREMENT INFORMATION
3.3V±5%
VDD
3.3V±5%
nCLK
VDD
SCOPE
Qx
V
V
Cross Points
PP
VDDA
CMR
CLK
HCSL
GND
nQx
GND
0V
3.3V HCSL OUTPUT LOAD AC TEST CIRCUIT
DIFFERENTIAL INPUT LEVEL
PCIEXC0,
PCIEXC1
PCIEXCx
PCIEXTy
PCIEXT0,
PCIEXT1
➤
➤
PCIEXCx
➤
tcycle n
tcycle n+1
➤
t jit(cc) = tcycle n –tcycle n+1
PCIEXTy
1000 Cycles
t sk(o)
OUTPUT SKEW
CYCLE-TO-CYCLE JITTER
PCIEXC0,
PCIEXC1
80%
80%
PCIEXT0,
PCIEXT1
VSW I N G
Clock
Outputs
20%
20%
tR
t PW
t
PERIOD
tF
odc =
t PW
x 100%
t PERIOD
HCSL OUTPUT RISE/FALL TIME
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD
6
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
APPLICATION INFORMATION
POWER SUPPLY FILTERING TECHNIQUES
As in any high speed analog circuitry, the power supply pins are
vulnerable to random noise. The ICS9DB202 provides separate
power supplies to isolate any high switching noise from the outputs to the internal PLL. VDD and VDDA should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter
performance, power supply isolation is required. Figure 1 illustrates how a 24Ω resistor along with a 10µF and a .01µF bypass
capacitor should be connected to each VDDA pin. The 10Ω resistor can also be replaced by a ferrite bead.
3.3V
VDD
.01µF
24Ω
VDDA
.01µF
10µF
FIGURE 1. POWER SUPPLY FILTERING
WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LEVELS
Figure 2 shows how the differential input can be wired to accept
single ended levels. The reference voltage V_REF = VDD/2 is
generated by the bias resistors R1, R2 and C1. This bias circuit
should be located as close as possible to the input pin. The ratio
of R1 and R2 might need to be adjusted to position the V_REF in
the center of the input voltage swing. For example, if the input
clock swing is only 2.5V and VDD = 3.3V, V_REF should be 1.25V
and R2/R1 = 0.609.
VDD
R1
1K
Single Ended Clock Input
CLK
V_REF
nCLK
C1
0.1u
R2
1K
FIGURE 2. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
7
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
DIFFERENTIAL CLOCK INPUT INTERFACE
The CLK /nCLK accepts LVDS, LVPECL, LVHSTL, SSTL, HCSL
and other differential signals. Both VSWING and VOH must meet the
VPP and VCMR input requirements. Figures 3A to 3D show interface
examples for the HiPerClockS CLK/nCLK input driven by the most
common driver types. The input interfaces suggested here are
examples only. Please consult with the vendor of the driver
component to confirm the driver termination requirements. For
example in Figure 3A, the input termination applies for ICS
HiPerClockS LVHSTL drivers. If you are using an LVHSTL driver
from another vendor, use their termination recommendation.
3.3V
3.3V
3.3V
1.8V
Zo = 50 Ohm
CLK
Zo = 50 Ohm
CLK
Zo = 50 Ohm
nCLK
Zo = 50 Ohm
LVPECL
nCLK
HiPerClockS
Input
LVHSTL
ICS
HiPerClockS
LVHSTL Driver
R1
50
R1
50
HiPerClockS
Input
R2
50
R2
50
R3
50
FIGURE 3A. HIPERCLOCKS CLK/NCLK INPUT DRIVEN BY
ICS HIPERCLOCKS LVHSTL DRIVER
FIGURE 3B. HIPERCLOCKS CLK/NCLK INPUT DRIVEN BY
3.3V LVPECL DRIVER
3.3V
3.3V
3.3V
3.3V
3.3V
R3
125
R4
125
Zo = 50 Ohm
LVDS_Driv er
Zo = 50 Ohm
CLK
CLK
R1
100
Zo = 50 Ohm
nCLK
LVPECL
R1
84
HiPerClockS
Input
nCLK
Receiv er
Zo = 50 Ohm
R2
84
FIGURE 3C. HIPERCLOCKS CLK/NCLK INPUT DRIVEN BY
3.3V LVPECL DRIVER
FIGURE 3D. HIPERCLOCKS CLK/NCLK INPUT DRIVEN
3.3V LVDS DRIVER
RECOMMENDATIONS FOR UNUSED INPUT AND OUTPUT PINS
INPUTS:
OUTPUTS:
LVCMOS CONTROL PINS:
All control pins have internal pull-ups or pull-downs; additional
resistance is not required but can be added for additional
protection. A 1kW resistor can be used.
HCSL OUTPUT
All unused HCSL outputs can be left floating. We recommend
that there is no trace attached. Both sides of the differential output
pair should either be left floating or terminated.
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
8
BY
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
RELIABILITY INFORMATION
TABLE 6A. θJAVS. AIR FLOW TABLE FOR 20 LEAD TSSOP PACKAGE
θJA by Velocity (Linear Feet per Minute)
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
0
200
500
114.5°C/W
73.2°C/W
98°C/W
66.6°C/W
88°C/W
63.5°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
TABLE 6B. θJAVS. AIR FLOW TABLE FOR 20 LEAD SSOP PACKAGE
θJA by Velocity (Linear Feet per Minute)
0
Multi-Layer PCB, JEDEC Standard Test Boards
80.8°C/W
200
73.2°C/W
500
69.2°C/W
TRANSISTOR COUNT
The transistor count for ICS9DB202 is: 2471
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
9
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
PACKAGE OUTLINE - G SUFFIX
FOR
20 LEAD TSSOP
PACKAGE OUTLINE - F SUFFIX FOR 20 LEAD SSOP
TABLE 6A. PACKAGE DIMENSIONS
SYMBOL
TABLE 6B. PACKAGE DIMENSIONS
Millimeters
Millimeters
Minimum
N
SYMBOL
Maximum
Minimum
20
N
Maximum
20
A
--
1.20
A
--
2.0
A1
0.05
0.15
A1
0.05
--
A2
0.80
1.05
A2
1.65
1.85
b
0.19
0.30
b
0.22
0.38
c
0.09
0.20
D
6.40
6.60
c
0.09
0.25
D
6.90
7.50
E
7.40
8.20
E1
5.0
5.60
E
E1
6.40 BASIC
4.30
e
4.50
0.65 BASIC
e
0.65 BASIC
L
0.45
0.75
α
0°
8°
L
0.55
0.95
0.10
α
0°
8°
aaa
--
Reference Document: JEDEC Publication 95, MO-153
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
Reference Document: JEDEC Publication 95, MO-150
10
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
TABLE 7. ORDERING INFORMATION
Part/Order Number
Marking
Package
Shipping Packaging
Temperature
ICS9DB202CG
ICS9DB202CG
20 Lead TSSOP
Tube
0°C to 70°C
ICS9DB202CGT
ICS9DB202CG
20 Lead TSSOP
2500 Tape & Reel
0°C to 70°C
ICS9DB202CGLF
ICS9DB202CGL
20 Lead "Lead-Free" TSSOP
Tube
0°C to 70°C
ICS9DB202CGLFT
ICS9DB202CGL
20 Lead "Lead-Free" TSSOP
2500 Tape & Reel
0°C to 70°C
ICS9DB202CF
ICS9DB202CF
20 Lead SSOP
Tube
0°C to 70°C
ICS9DB202CFT
ICS9DB202CF
20 Lead SSOP
1000 Tape & Reel
0°C to 70°C
ICS9DB202CFLF
ICS9DB202CFLF
20 Lead "Lead-Free" SSOP
Tube
0°C to 70°C
ICS9DB202CFLFT
ICS9DB202CFLF
20 Lead "Lead-Free" SSOP
1000 Tape & Reel
0°C to 70°C
NOTE: Par ts that are ordered with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology, Incorporated (IDT) assumes no responsibility for either its use or for
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial and
industrial applications. Any other applications such as those requiring high reliability or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT
reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
11
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
REVISION HISTORY SHEET
Rev
Table
Page
B
T4D
4
6
8
B
B
B
T7
T4 D
Description of Change
Date
12/21/04
11
4
HCSL Table -adjusted VOH min from 680mV to 610mV and added VOH max.
Updated HCSL Output Load AC Test Circuit Diagram.
Application Information - added Recommendations for Unused Input and
Output Pins.
Ordering Information Table - added lead-free note.
HCSL DC Characteristics - corrected units for VOH & VOL from V to mV.
1
Feature Section - added Input Frequency Range and VCO Range.
7/14/06
IDT ™ / ICS™ PCI EXPRESS JITTER ATTENUATOR
12
3/8/06
5/26/06
ICS9DB202CG REV B JULY 14, 2006
ICS9DB202
PCI EXPRESS JITTER ATTENUATOR
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
[email protected]
480-763-2056
Corporate Headquarters
Asia Pacific and Japan
Europe
Integrated Device Technology, Inc.
6024 Silver Creek Valley Road
San Jose, CA 95138
United States
800 345 7015
+408 284 8200 (outside U.S.)
Integrated Device Technology
Singapore (1997) Pte. Ltd.
Reg. No. 199707558G
435 Orchard Road
#20-03 Wisma Atria
Singapore 238877
+65 6 887 5505
IDT Europe, Limited
321 Kingston Road
Leatherhead, Surrey
KT22 7TU
England
+44 (0) 1372 363 339
Fax: +44 (0) 1372 378851
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, the IDT logo and HiPerClockS are trademarks of
Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be
trademarks or registered trademarks used to identify products or services of their respective owners.
Printed in USA
Similar pages