APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS General Description Features • • • • Push-Pull RESET Active Low (APX809) • • • • • • Push-Pull RESET Active High (APX810) 200ms Typ Power-On Reset Pulse Width 30µA Supply Current (Typ.) Guaranteed Reset Valid to VCC = +1V No External Components SOT23 and SOT23R: Available in “Green” Molding Compound (No Br, Sb) Lead Free Finish/RoHS Compliant (Note 1) • The APX809/810 are used for microprocessor (µP) supervisory circuits to monitor the power supplies in µP and digital systems. They provide excellent circuit reliability and low cost by eliminating external components and adjustments when used with +5V, +3.3V, +3.0V powered circuits. Precision Monitoring of +2.5V, +3V, +3.3V, and +5V Power-Supply Voltages Fully Specified Over Temperature Available in three Output Configurations These circuits perform a single function: they assert a reset signal whenever the VCC supply voltage declines below a preset threshold, keeping it asserted for at least 240ms after VCC has risen above the reset threshold. Reset thresholds suitable for operation with a variety of supply voltages are available. The APX809/810 have push pull outputs. The APX809 have an active low RESET output, while the APX810 has an active high RESET output. The reset comparator is designed to ignore fast transients on VCC, and the outputs are guaranteed to be in the correct logic state for VCC down to 1V. Low supply current makes the APX809/810 ideal for use in portable equipment. The APX809/810 is available in a 3-pin SOT23 and SOT23R packages. Applications • • • • • • Computers Controllers Intelligent Instruments Critical µP and µC Power Monitoring Portable/Battery Powered Equipment Automotive Ordering Information APX 8 XX - XX XX G - 7 Enable 09 : Active-Low 10 : Active-High Device APX809-XXSAG-7 APX810-XXSAG-7 APX809-XXSRG-7 APX810-XXSRG-7 Notes: Package Code SA SA SR SR Voltage 46 44 40 31 29 26 23 : 4.63 : 4.38 : 4.00 : 3.08 : 2.93 : 2.63 : 2.25 Package Green Packing SA : SOT23 SR : SOT23R G : Green 7 : Tape & Reel Packaging (Note 2) SOT23 SOT23 SOT23R SOT23R 7” Tape and Reel Quantity Part Number Suffix 3000/Tape & Reel -7 3000/Tape & Reel -7 3000/Tape & Reel -7 3000/Tape & Reel -7 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. APX809/810 Rev. 4 1 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Pin Assignments ( Top View ) GND ( Top View ) 1 RESET (RESET) APX809 APX810 RESET (RESET) 3 1 APX809 APX810 VCC GND 2 3 VCC 2 SOT23 SOT23R Pin Descriptions Pin Name Description GND Ground Reset Output Pin L: for APX809 H: for APX810 RESET (RESET) VCC Operating Voltage Input Absolute Maximum Ratings Symbol ESD HBM ESD MM VCC VRESET ICC IO Parameter Human Body Model ESD Protection Machine Model ESD Protection Supply Voltage RESET, RESET (push-pull) Input Current, VCC Rating Unit 5 KV 500 V -0.3 to +6.0 V -0.3 to (VCC + 0.3) V 20 mA 20 mA 400 mW TOP Output Current, RESET, RESET Continuous Power Dissipation (TA = +70°C), de-rate 4mW/°C above +70°C Operating Junction Temperature Range -40 to +105 °C TST Storage Temperature Range -65 to +150 °C PD APX809/810 Rev. 4 2 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Recommended Operating Conditions Symbol VCC VIN TA TR Parameter Supply Voltage Input Voltage Operating Ambient Temperature Range Vcc Rising Time (Vcc = 0~VT) Electrical Characteristics Max 5.5 (VCC+0.3) 85 100 Unit V V o C V/ uS (TA = 25ºC) TA= -40 to 85 oC unless otherwise note. Typical values are at TA=+25 oC. Symbol Parameter Test Conditions VCC VCC Range TA = 0oC to +70oC ICC Supply Current VTH + 0.2V APX809/810-23 APX809/810-26 APX809/810-29 o o APX809/810-31 TA = 0 C-85 C APX809/810-40 APX809/810-44 APX809/810-46 Reset VTH Threshold APX809/810-23 APX809/810-26 APX809/810-29 APX809/810-31 TA = -40oC-85oC APX809/810-40 APX809/810-44 APX809/810-46 Reset Threshold Tempco TS Set-up Time VCC = VTH to (VTH – 100mV) TDELAY Reset Active Timeout Period TA = 0oC to +85oC VCC = VTH -0.2, ISINK = 1.2mA RESET Output Voltage Low VOL VCC = VTH -0.2, ISINK = 3.2mA (APX809) VCC > 1.0V, ISINK = 50uA VCC > VTH +0.2, ISOURCE = 500uA Output Voltage-High RESE T VOH VCC > VTH +0.2, (APX809) ISOURCE = 800uA VCC = VTH +0.2, ISINK = 1.2mA RESET Output Voltage-Low VOL (APX810) VCC = VTH +0.2, ISINK = 3.2mA RESET Output Voltage-High 1.8V < VCC < VTH -0.2, VOH (APX810) ISOURCE = 150uA Thermal Resistance θJA SOT23/SOT23R (Note 3) Junction-to-Ambient Thermal Resistance θJC SOT23/SOT23R (Note 3) Junction-to-Case Notes: Min 1.1 0 -40 Min 1.0 2.21 2.59 2.88 3.02 3.93 4.31 4.56 2.20 2.57 2.86 3.00 3.92 4.29 4.54 140 Typ. 30 2.25 2.63 2.93 3.08 4.00 4.38 4.63 2.25 2.63 2.93 3.08 4.00 4.38 4.63 30 20 200 Max 5.5 40 2.30 2.69 3.00 3.15 4.08 4.47 4.72 2.30 2.69 3.00 3.15 4.08 4.47 4.72 280 0.3 0.4 0.3 Unit V μA V V ppm/ oC μs ms V 0.8VCC V VCC –1.5 0.3 0.4 V V 0.8 VCC 201 o C/W 56 o C/W 3. Test condition for SOT23/ SOT23R: Devices mounted on FR-4 substrate PC board, 2oz copper, with minimum recommended pad layout. APX809/810 Rev. 4 3 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Typical Application Circuit V CC CIN 100nF V CC V CC APX8XX Microprocessor RESET INPUT RESET (RESET) GND GND Functional Description A microprocessor’s (µP’s) reset input starts the µP in a known state. The APX809/810 assert reset to prevent code-execution errors during power-up, power-down, or brownout conditions. They assert a reset signal whenever the VCC supply voltage declines below a preset threshold, keeping it asserted for at least 240ms after VCC has risen above the reset threshold. The APX809/810 have a push-pull output stage. high-impedance CMOS logic inputs connected to RESET can drift to undetermined voltages. This presents no problem in most applications since most µP and other circuitry is inoperative with VCC below 1V. However, in applications where RESET must be valid down to 0V, adding a pull down resistor to RESET causes any stray leakage Ensuring a Valid Reset Output Down to VCC = 0 currents to flow to ground, holding RESET not critical; 100k are large enough not to load is guaranteed to be a logic low for VCC > 1V. Once VCC exceeds the reset threshold, an internal timer keeps RESET low for the reset timeout period; after this interval, RESET goes high. If a brownout condition occurs (VCC dips below the RESET reset threshold), RESET goes low. Any time VCC goes below the reset threshold, the internal timer resets to zero, and RESET goes low. The internal timer starts after VCC returns above the reset threshold, and low for the reset timeout period. RESET remains RESET low. R1’s value is RESET small enough to pull RESET to ground. For the RESET is required to remain valid for VCC < 1V. and APX810 if Benefits of Highly Accurate Reset Threshold Most µP supervisor ICs has reset threshold voltages between 5% and 10% below the value of nominal supply voltages. This ensures a reset will not occur within 5% of the nominal supply, but will occur when the supply is 10% below nominal. When using ICs rated at only the nominal supply ±5%, this leaves a zone of uncertainty where the supply is between 5% and 10% low, and where the reset may or may not be asserted. When VCC falls below 1V, the APX809 RESET output no longer sinks current—it becomes an open circuit. Therefore, APX809/810 Rev. 4 4 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Block Diagram Driver Delay Circuit RESET / RESET VREF APX809/810 Rev. 4 5 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Performance Characteristics RESET Threshold Voltage vs. Temperature RESET Timeout Period vs. Temperature 3.2 RESET Thershold Voltage (V) RESET Timeout Period (mS) 250 240 230 220 210 200 190 180 170 160 150 -40℃ -25℃ 0℃ 25℃ 50℃ 3.15 3.1 3.05 3 2.95 2.9 2.85 2.8 85℃ 105℃ 125℃ -40℃ -25℃ Temperature 0℃ Figure 1 50℃ 85℃ 105℃ 125℃ Figure 2 Supply Current vs. Vcc Vcc Supply Current vs. Temperature (Vcc=3.3V Vth=2.93V) 35 40 34 35 Supply Current (uA) Vcc Supply Current (uA) 25℃ Temperature 33 32 31 30 29 28 27 30 25 20 15 10 5 26 25 0 -40℃ -25℃ 0℃ 25℃ 50℃ 85℃ 105℃ 125℃ Temperature 2.5V 3.3V 4.0V 5.0V 5.5V Vcc Figure 3 APX809/810 Rev. 4 1.5V Figure 4 6 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Timing Diagram Vth Vcc Vth TDelay TDelay TDelay TDelay /RESET Vth RESET APX809/810 Rev. 4 7 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Marking Information (1) SOT23/SOT23R ( Top View ) 3 XX Y W X 1 Device APX809-46SA APX809-44SA APX809-40SA APX809-31SA APX809-29SA APX809-26SA APX809-23SA APX810-46SA APX810-44SA APX810-40SA APX810-31SA APX810-29SA APX810-26SA APX810-23SA APX809-46SR APX809-44SR APX809-40SR APX809-31SR APX809-29SR APX809-26SR APX809-23SR APX810-46SR APX810-44SR APX810-40SR APX810-31SR APX810-29SR APX810-26SR APX810-23SR APX809/810 Rev. 4 2 XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green Package SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23 SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R SOT23R 8 of 9 www.diodes.com Identification Code X2 X3 X4 X5 X6 X7 X8 XA XB XC XD XE XF XG Y2 Y3 Y4 Y5 Y6 Y7 Y8 YA YB YC YD YE YF YG FEBRUARY 2009 © Diodes Incorporated APX809/810 3-PIN MICROPROCESSOR RESET CIRCUITS Package Information (All Dimensions in mm) (1) Package Type: SOT23/SOT23R Notes: 4. Package outline dimensions as shown on Diodes Inc. package outline dimensions document AP02002, which can be found on our website at http://www.diodes.com/datasheets/ap02002.pdf IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. APX809/810 Rev. 4 9 of 9 www.diodes.com FEBRUARY 2009 © Diodes Incorporated