MIC803 3-Pin Microprocessor Supervisor Circuit with Open-Drain Reset Output General Description Features The MIC803 is a single-voltage supervisor with open-drain reset output that provides accurate power supply monitoring and reset generation in microprocessor-based systems. The function of the device is to assert a reset signal if the power supply voltage drops below the reset threshold voltage, and retain this reset for the reset timeout period once the power supply increases above the reset threshold voltage. • • • • The MIC803 consumes only 4.5µA of supply current and offers three reset delay periods of 20ms, 140ms, and 1120ms (minimum). It features factory-programmed reset threshold levels from 2.63V to 4.63V to accommodate 3.0V, 3.3V, and 5.0V power supplies. It is available in the compact 3-pin SC-70 and SOT-23 packages. Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. • • • • • 4.5μA supply current (typical) at 3.6V Open-drain /RESET output /RESET remains valid with VCC as low as 1V 20ms, 140ms, or 1120ms (minimum) reset timeout options 2.63V to 4.63V preset voltage threshold options 2.5% voltage threshold accuracy over temperature 3-pin SC70-3 package (2.0mm × 2.1mm) 3-pin SOT-23 package (2.3mm × 2.9mm) -40˚C to +125˚C junction temperature range Applications • • • • • Critical microcomputer power monitoring Portable equipment Solid state drives Printers/computers Embedded controllers Typical Application VCC VCC VCC 100k MIC803 RESET GND µP RESET GND Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 3, 2015 Revision 1.2 Micrel, Inc. MIC803 Ordering Information(1) Part Number (2) Marking Nominal VTH (V) Minimum (3) tRESET (ms) Junction Temperature Range Package MIC803-46D2VC3 AS 4.63 20 –40° to +125°C SC70-3 MIC803-44D2VC3 AP 4.38 20 –40° to +125°C SC70-3 MIC803-41D2VC3 AK 4.10 20 –40° to +125°C SC70-3 MIC803-40D2VC3 A2 4.00 20 –40° to +125°C SC70-3 MIC803-31D2VC3 AG 3.08 20 –40° to +125°C SC70-3 MIC803-30D2VC3 AV 3.00 20 –40° to +125°C SC70-3 MIC803-29D2VC3 AD 2.93 20 –40° to +125°C SC70-3 MIC803-26D2VC3 AA 2.63 20 –40° to +125°C SC70-3 MIC803-46D3VC3 AT 4.63 140 –40° to +125°C SC70-3 MIC803-44D3VC3 AQ 4.38 140 –40° to +125°C SC70-3 MIC803-41D3VC3 AM 4.10 140 –40° to +125°C SC70-3 MIC803-40D3VC3 A5 4.00 140 –40° to +125°C SC70-3 MIC803-31D3VC3 A4 3.08 140 –40° to +125°C SC70-3 MIC803-30D3VC3 AX 3.00 140 –40° to +125°C SC70-3 MIC803-29D3VC3 AE 2.93 140 –40° to +125°C SC70-3 MIC803-26D3VC3 AB 2.63 140 –40° to +125°C SC70-3 MIC803-46D4VC3 AU 4.63 1120 –40° to +125°C SC70-3 MIC803-44D4VC3 AR 4.38 1120 –40° to +125°C SC70-3 MIC803-41D4VC3 AN 4.10 1120 –40° to +125°C SC70-3 MIC803-40D4VC3 A6 4.00 1120 –40° to +125°C SC70-3 MIC803-31D4VC3 AJ 3.08 1120 –40° to +125°C SC70-3 MIC803-30D4VC3 AZ 3.00 1120 –40° to +125°C SC70-3 MIC803-29D4VC3 A3 2.93 1120 –40° to +125°C SC70-3 MIC803-26D4VC3 AC 2.63 1120 –40° to +125°C SC70-3 MIC803-46D2VM3 AS 4.63 20 –40° to +125°C SOT23-3 MIC803-44D2VM3 AP 4.38 20 –40° to +125°C SOT23-3 MIC803-41D2VM3 AK 4.10 20 –40° to +125°C SOT23-3 MIC803-40D2VM3 A2 4.00 20 –40° to +125°C SOT23-3 MIC803-31D2VM3 AG 3.08 20 –40° to +125°C SOT23-3 MIC803-30D2VM3 AV 3.00 20 –40° to +125°C SOT23-3 MIC803-29D2VM3 AD 2.93 20 –40° to +125°C SOT23-3 MIC803-26D2VM3 AA 2.63 20 –40° to +125°C SOT23-3 MIC803-46D3VM3 AT 4.63 140 –40° to +125°C SOT23-3 Note: 1. All devices available in tape and reel only. (Order entry PN, add TR. Example: MIC803-26D4VM3 TR) Standard/full reel quantity is 3,000 pieces. Reel diameter is 7 inches. Hub diameter is 2 inches. Width is 8mm. 2. Underbar symbol (_) may not be to scale. 3. –40° to +85°C temperature range. August 3, 2015 2 Revision 1.2 Micrel, Inc. MIC803 Ordering Information(1) (Continued) Part Number (2) Marking Nominal VTH (V) Minimum (3) tRESET (ms) Junction Temperature Range Package MIC803-44D3VM3 AQ 4.38 140 –40° to +125°C SOT23-3 MIC803-41D3VM3 AM 4.10 140 –40° to +125°C SOT23-3 MIC803-40D3VM3 A5 4.00 140 –40° to +125°C SOT23-3 MIC803-31D3VM3 A4 3.08 140 –40° to +125°C SOT23-3 MIC803-30D3VM3 AX 3.00 140 –40° to +125°C SOT23-3 MIC803-29D3VM3 AE 2.93 140 –40° to +125°C SOT23-3 MIC803-26D3VM3 AB 2.63 140 –40° to +125°C SOT23-3 MIC803-46D4VM3 AU 4.63 1120 –40° to +125°C SOT23-3 MIC803-44D4VM3 AR 4.38 1120 –40° to +125°C SOT23-3 MIC803-41D4VM3 AN 4.10 1120 –40° to +125°C SOT23-3 MIC803-40D4VM3 A6 4.00 1120 –40° to +125°C SOT23-3 MIC803-31D4VM3 AJ 3.08 1120 –40° to +125°C SOT23-3 MIC803-30D4VM3 AZ 3.00 1120 –40° to +125°C SOT23-3 MIC803-29D4VM3 A3 2.93 1120 –40° to +125°C SOT23-3 MIC803-26D4VM3 AC 2.63 1120 –40° to +125°C SOT23-3 Part Numbering Convention August 3, 2015 3 Revision 1.2 Micrel, Inc. MIC803 Pin Configuration 3-Pin SC70 (Top View) 3-Pin SOT-23 (Top View) Pin Description Pin Number Pin Name 1 GND 2 /RESET 3 VCC August 3, 2015 Pin Function Ground Pin. /RESET goes low if VCC falls below the reset threshold (VTH), and remains asserted for one timeout period after VCC exceeds VTH. Power Supply Input and Monitored Voltage. 4 Revision 1.2 Micrel, Inc. MIC803 Absolute Maximum Ratings(4) Operating Ratings(5) Supply Voltage (VCC) ...................................... –0.3V to 6.0V Reset Output (/RESET).................................. –0.3V to 6.0V Input Current (VCC) ...................................................... 20mA Output Current (/RESET) ............................................ 20mA Rate of Rise (VCC) ................................................... 100V/µs Junction Temperature (TJ)…………………………....+150°C Lead Temperature (soldering, 10s) ............................ 260°C Storage Temperature (TS) ......................... –65°C to +150°C (6) ESD Rating .................................................................. 3kV Supply Voltage (VCC) ........................................ 1.0V to 5.5V Reset Output Voltage (/RESET) ...................... 0.0V to 5.5V Junction Temperature (TJ) ........................ –40°C to +125°C Junction Thermal Resistance 3-Pin SC70 (θJA) .............................................. 260°C/W 3-Pin SOT-23 (θJA) ........................................... 203°C/W Electrical Characteristics(7) For typical values, VCC = 5.0V for MIC803-46/44/41/40, VCC = 3.3V for MIC803-31/30/29, VCC = 3.0V for MIC803-26; TJ = 25°C, Bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Parameter Conditions Min. Typ. Max. Units Power Supply Input Operating Voltage Range (VCC) TJ = –40˚C to +85˚C 1.0 5.5 TJ = –40˚C to +125˚C 1.2 5.5 TJ = –40˚C to +85˚C Supply Current (ICC) TJ = +85˚C to +125˚C VCC = 5.5V, No Load 5.5 15 VCC = 3.6V, No Load 4.5 10 VCC = 5.5V, No Load 18 VCC = 3.6V, No Load 13 V µA Voltage Threshold MIC803-46 MIC803-44 Reset Threshold (VTH) MIC803-41 MIC803-40 MIC803-31 TJ = –40˚C to +85˚C 4.50 TJ = –40˚C to +125˚C 4.44 TJ = –40˚C to +85˚C 4.25 TJ = –40˚C to +125˚C 4.20 TJ = –40˚C to +85˚C 4.00 TJ = -40˚C to +125˚C 3.97 TJ = –40˚C to +85˚C 3.89 TJ = –40˚C to +125˚C 3.80 TJ = –40˚C to +85˚C 3.00 TJ = –40˚C to +125˚C 2.95 4.63 4.75 4.82 4.38 4.50 4.56 4.10 4.20 V 4.24 4.00 4.10 4.20 3.08 3.15 3.21 Notes: 4. Exceeding the absolute maximum ratings may damage the device. 5. The device is not guaranteed to function outside its operating ratings. 6. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5kΩ in series with 100pF. 7. Specification for packaged product only. August 3, 2015 5 Revision 1.2 Micrel, Inc. MIC803 Electrical Characteristics(7) (Continued) For typical values, VCC = 5.0V for MIC803-46/44/41/40, VCC = 3.3V for MIC803-31/30/29, VCC = 3.0V for MIC803-26; TJ = 25°C, Bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Parameter Conditions Min. Typ. Max. TJ = –40˚C to +85˚C 2.93 3.00 3.08 TJ = –40˚C to +125˚C 2.90 TJ = –40˚C to +85˚C 2.82 TJ = –40˚C to +125˚C 2.81 TJ = –40˚C to +85˚C 2.55 TJ = –40˚C to +125˚C 2.50 Units Voltage Threshold (Continued) MIC803-30 Reset Threshold (VTH) MIC803-29 MIC803-26 3.11 2.93 3.00 3.05 2.63 V 2.70 2.76 Reset Time VCC to /RESET Delay (tD) VCC = VTH to (VTH – 100mV) D2 Reset Timeout Period (tRESET) D3 D4 15 TJ = –40˚C to +85˚C 20 TJ = –40˚C to +125˚C 16 TJ = –40˚C to +85˚C 140 TJ = –40˚C to +125˚C 112 TJ = –40˚C to +85˚C 1120 TJ = –40˚C to +125˚C 900 35 µs 44 48 230 360 420 1800 ms 2400 3200 Reset Output /RESET Output Voltage (VOL) /RESET Output Leakage August 3, 2015 VCC ≥ 4.0V, ISINK = 3.2mA 0.4 V VCC > 2.5V, ISINK = 1.2mA 0.3 V VCC ≥ 1.0V, ISINK = 50µA 0.3 V 1 μA VCC > VTH, /RESET Deasserted 6 Revision 1.2 Micrel, Inc. MIC803 Typical Characteristics 30 6 5 4 3 300 RESET TIMEOUT PERIOD (ms) VCC = 3.6V VCC to /RESET DELAY (µs) SUPPLY CURRENT (µA) 7 VCC = VTH to VTH -100mV 25 20 15 10 5 0 -50 -20 10 40 70 100 130 VCC = 5.5V 280 260 240 220 200 -50 -20 TEMPERATURE (°C) 10 40 70 100 130 -50 TEMPERATURE (°C) Normalized Reset Threshold vs. Temperature 0.992 0.988 -20 10 40 70 TEMPERATURE (°C) August 3, 2015 100 130 70 100 130 VTH = 2.93V 6 4 2 0 -50 40 50 VTH = 2.93V MAXIMUM TRANSIENT DURATION (µs) SUPPLY CURRENT (µA) 0.996 10 Maximum Transient Duration vs Overdrive 8 1.000 -20 TEMPERATURE (°C) VCC Operating Supply Current vs. Supply Voltage 1.004 NORMALIZED RESET THRESHOLD (V) Reset Timeout Period (D3) vs. Temperature VCC to /RESET Delay vs. Temperature VCC Operating Supply Current vs. Temperature 40 30 20 10 0 0 1 2 3 4 SUPPLY VOLTAGE (V) 7 5 6 0 200 400 600 800 1000 OVERDRIVE VOLTAGE, VTH - VCC (mV) Revision 1.2 Micrel, Inc. MIC803 Timing Diagram VTH VCC 0V RESET VOL tRESET tD tRESET Functional Diagram MIC803 RESET (2) VCC (3) RESET GENERATOR + - VTH GND (1) August 3, 2015 8 Revision 1.2 Micrel, Inc. MIC803 Application Information Microprocessor Reset The /RESET pin is asserted whenever VCC falls below the reset threshold voltage, VTH. The /RESET pin remains asserted for the duration of the reset timeout period (tRESET) after VCC has risen above the reset threshold voltage. The reset function ensures the microprocessor is properly reset and powers up in a known condition after a power failure. /RESET will remain valid with VCC as low as 1.0V. /RESET Valid at Low Voltage As VCC drops to 0V, the MIC803 will no longer be able to pull the /RESET output low, and the pull-up resistor will pull the output high. The value of the pull-up resistor and the voltage it is connected to will affect the point at which this happens. The /RESET output is a simple open-drain N-channel MOSFET structure. A pull-up resistor must be used to pull this output up to some voltage. For most applications, this voltage will be the same power supply that supplies VCC to the MIC803. As shown in Figure 1, it is possible, however, to tie this resistor to some other voltage. This will allow the MIC803 to monitor one voltage while levelshifting the /RESET output to some other voltage. The pull-up voltage must be limited to 5.5V. The resistor must be small enough to supply current to the inputs and leakage paths that are driven by the /RESET output. Figure 2. /RESET at Falling VCC +5V +3.3V Wire ORing the /RESET Output Since the /RESET output is open-drain, several reset sources can be wire-ORed, in parallel, to allow resets from multiple sources. VCC VCC 100k µP MIC803 RESET GND VCC Transients The MIC803 is relatively immune to negative-going VCC glitches below the reset threshold (see Typical Characteristics, graph titled “Maximum Transient Duration vs. Overdrive”). As shown in Figure 3, the overdrive voltage is the difference between the threshold voltage and the minimum point of the VCC glitch. Typically, an overdrive of 100mV, with duration of 15μs or less will not cause a reset. If additional transient immunity is needed, a 0.1μF bypass capacitor can be placed as close as possible to the MIC803 on the VCC pin. RESET GND Figure 1. MIC803 Used in a Multiple Supply System Figure 3. VCC Threshold August 3, 2015 9 Revision 1.2 Micrel, Inc. MIC803 Package Information and Recommended Landing Pattern(8) 3-Pin SC70 (MM) Note: 8. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. August 3, 2015 10 Revision 1.2 Micrel, Inc. MIC803 Package Information and Recommended Landing Pattern(8) 3-Pin SOT-23 (MM) August 3, 2015 11 Revision 1.2 Micrel, Inc. MIC803 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2010 Micrel, Incorporated. August 3, 2015 12 Revision 1.2