MEDICAL & MILITARY Medline 300 Series 2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Features • EN61000-3-2 class A and D compliant. • Power factor 0.98 typical. • Remote sense on output 1 and output 2. • Overvoltage protection. • Overcurrent protection. • Power fail detection (PFD) signal. • 100% burn-in at full rated load. • Remote inhibit - TTL high disables output. • Short curcuit protection Specifications OPERATING INPUT Input Voltage 90-264Vac Frequency 47Hz–63Hz Input Current 4.7A (rms) for 115Vac 2.2A (rms) for 230Vac Leakage current Isolation Inrush Current MTBF 350,000 hrs @ 25°C Efficiency 70% minimum. ENVIRONMENTAL Operating Temperature 0°C to 70°C 90µA max. at 115Vac. 60Hz 150µA max. at 230Vac. 50Hz Derating Derate from 100% at +50°C linearly to 50% at 70°C Input – Output: 4000VAC Input – Ground: 1500VAC Output – Ground: 500VAC Storage Temperature -40°C to 85°C Humidity 5%–95% non-condensing 30A at 115V or 80A at 230V at 25°C and cold start Cooling 35 CFM forced air, provided on “C” version, to be provided for “B” version by user STANDARDS AND APPROVALS OUTPUT Power See table Safety standards UL60601-1, TUV EN60601-1 Voltage See table C-Tick AS/NZS CISPR11 Group 1, Class A Ripple & Noise 2% peak to peak max EMC standards EN55011 Class B, FCC Class B, EN61000-3-2, -3, EN61000-4-2, -3, -4, -5, -6, -8, -11 Overvoltage Protection Provided on output #1 only. Set at 115%–140% of nominal output voltage MECHANICAL Overcurrent Protection All outputs protected for short circuit conditions Dimensions 177.8x101.6x38.1mm Weight 0.82Kgs for “B” version. 0.96Kgs for “C” version. Temperature Coefficient All outputs ±0.04% per °C Transient Response Max. excursion of 4%or better on all models, recovering to 1% of final value within 500µs after a 25% step load change PFD Signal TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation Remote inhibit Requires an external TTL high level signal to inhibit outputs for standard models Line Regulation ±0.2% maximum at full load Holdup Time Typically 12ms at 110VAC Your dependable power partner – www.powerbox.com.au 347 MEDICAL & MILITARY Medline 300 Series 2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Selection Table MAX. MODEL OUTPUT #1 OUTPUT #2 VNOM IMIN IMAX OUTPUT #3 TOL VNOM OUTPUT #4 IMIN IMAX TOL VNOM IMIN OUTPUT NUMBER VNOM IMIN IMAX TOL OBP02013 3.3V 0A 60A 3% IMAX TOL POWER 200W OBP02016 5.1V 0A 60A 2% 300W OBP02031 12V 0A 25A 2% 300W OBP02037 15V 0A 20A 2% 300W OBP02046 24V 0A 12.5A 2% 300W OBP02055 30V 0A 10A 2% 300W OBP02170 48V 0A 6.3A 2% OBP02403 +3.3V 3.0A 35A 3% 5.1V 2.0A 22A 2% 12V 0A 4A 4% 12V 0A 4A 4% 300W 250W OBP02404 +5.1V 2.0A 35A 2% 12V 1.0A 10A 2% 12V 0A 4A 4% 5.1V 0A 4A 4% 300W OBP02407 +5.1V 2.0A 35A 2% 15V 0.8A 8A 2% 15V 0A 4A 4% 24V 0A 2.5A 4% 300W OBP02410 +5.1V 2.0A 35A 2% 12V 1.0A 10A 2% 12V 0A 4A 4% 12V 0A 4A 4% 300W OBP02413 +5.1V 2.0A 35A 2% 12V 1.0A 10A 2% 12V 0A 4A 4% 24V 0A 2.5A 4% 300W OBP02418 +5.1V 2.0A 35A 2% 12V 1.0A 10A 2% 12V 0A 4A 4% 15V 0A 4A 4% 300W OBP02419 +5.1V 2.0A 35A 3% 24V 0.5A 5A 2% 12V 0A 4A 4% 12V 0A 4A 4% 300W OBP02424 +5.1V 2.0A 35A 2% 24V 0.5A 5A 2% 5.1V 0A 4A 4% 15V 0A 4A 4% 300W OBP02427 +5.1V 2.0A 35A 2% 12V 1.0A 10A 2% 5.1V 0A 4A 4% 24V 0A 2.5A 4% 300W OBP02430 24V 0.5A 6.3A 2% 12V 1.0A 10A 2% 5.1V 0A 4A 4% 12V 0A 4A 4% 300W OBP02433 24V 0.5A 6.3A 2% 12V 1.0A 10A 2% 5.1V 0A 4A 4% 24V 0A 2.5A 4% 300W OBP02436 24V 0.5A 6.3A 2% 12V 1.0A 10A 2% 12V 0A 4A 4% 12V 0A 4A 4% 300W OBP02439 24V 0.5A 6.3A 3% 24V 0.5A 5A 2% 5.1V 0A 4A 4% 15V 0A 4A 4% 300W OBP02442 24V 0.5A 6.3A 2% 24V 0.5A 5A 2% 12V 0A 4A 4% 12V 0A 4A 4% 300W NOTES: (1) Add suffix “B” for U-bracket format and “C” for enclosed format. (2) All outputs are floating. It can be connected externally for postive or negative output. (3) Output 1 and 2 can be adjusted within ±5% of their nominal voltage. (4) Output 3 and 4 can be adjusted within ±15% of their nominal voltage. (5) 300 watts for “C” version with a cover and fan assembly 150 watts for “B” version without moving air (maximum current of ouput #1 & #2 derated to 50%), or 300 watts with 25 CFM forced air provided by user. (6) PM300-10-3 is rated 200 watts with 35 CFM forced air cooling or 100 watts convectional cooled. PM300-40-3 is rated 250 watts with 35 CFM forced air cooling (maximum current of output 1 & 2 derated to 50%) or 125 watts convection cooled. (7) Single output models may be operated at no-load. At no-load, output voltage tolerance increases to 10%. Pin Connection CONNECTOR P1(AC) MODEL/PIN OBP02013 OBP02031 OBP02046 OBP02070 OBP02016 OBP02037 OBP02055 1 2 3 Live Neutral Ground P2 P3 P4 OUTPUT OUTPUT #1 OUTPUT #1 P5 P6 OUTPUT #1 OUTPUT #1 #1 RET CONNECTOR P4 MODEL/PIN OBP02013 OBP02031 OBP02046 OBP02070 348 OBP02016 OBP02037 OBP02055 1 2 3 4 5 6 7 8 9 10 SIGNAL GROUND +S (Vo1) -S (Vo1) PFD INHIBIT N.C. N.C. N.C. OV (FAN) 12V (FAN) MEDICAL & MILITARY Medline 300 Series 2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Pin Connection ctnd P1(AC) MODEL/PIN OBP02403 OBP02407 OBP02413 OBP02419 OBP02427 OBP02433 OBP02439 OBP02404 OBP02410 OBP02418 OBP02424 OBP02430 OBP02436 OBP02442 P2 1 2 3 Live Neutral Ground P3 OUTPUT #1 P5 OUTPUT #1 RET P7 P6 OUTPUT #2 OUTPUT #2 RET 1 2 3 4 OUTPUT #3 OUTPUT #3 RET OUTPUT #4 OUTPUT #4 RET CONNECTOR P4 MODEL/PIN OBP02403 OBP02407 OBP02413 OBP02419 OBP02427 OBP02433 OBP02439 OBP02404 OBP02410 OBP02418 OBP02424 OBP02430 OBP02436 OBP02442 1 2 3 4 5 6 7 8 9 10 SIGNAL GROUND +S (Vo1) -S (Vo1) PFD INHIBIT N.C. N.C. N.C. OV (FAN) 12V (FAN) Technical Illustration MULTIPLE SINGLE Note: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum Input connector P1 is DT-35-B01W-03 screws are M3, Nickel plated 3. Connector P4 mates with Molex housing 50-37-5103 and pins 5263 4. Connectors P2, P3, P5 and P6: M3*0.5 screw connections 5. 12V (P4) is for DC fan rated 12V/0.1A 6. Weight 1.20 Kgs approx Note: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector P1 Dinkle is DT-35-B01W-03 screws are M3, Nickel plated 4. Connector P4 mates with Molex housing 50-37-5103 and pins 5263 5. Connectors P2, P3, P5 and P6: M3*0.5 screw connections 6. Output connector P7 mates Molex housing 09-50-3041 and Molex 2878 series crimp terminal 7. 12V (P4) is for DC fan rated 12V/0.1A 8. Weight 1.20 Kgs approx Your dependable power partner – www.powerbox.com.au 349