ZETTLER AZ940-1C-18D 10 amp miniature power relay Datasheet

AZ940
10 AMP MINIATURE
POWER RELAY
FEATURES
•
•
•
•
•
10 Amp switching capability
4 kV dielectric strength
Epoxy sealed version available
UL, CUR file E44211
VDE file 134326
CONTACTS
GENERAL DATA
Arrangement
SPST (1 Form A)
SPDT (1 Form C)
Ratings
Resistive load:
Max. switched power: 150 W or 1250 VA (N.O.)
90 W or 750 VA (N.C.)
Max. switched current: 10 A (N.O.), 3 A (N.C.)
Max. switched voltage: 150 VDC* or 400 VAC
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL, CUR
(N.O.)
10 A at 125 VAC general use, 100K cycles [1] [2]
10 A at 277 VAC cos phi 0.4, 10K cycles [1] [2]
5 A at 250 VAC general use, 100K cycles [1] [2]
5 A at 30 VDC [1] [2]
1/ HP at 125 VAC, 100K cycles [1] [2]
10
1/
6
UL, CUR
(N.C.)
HP at 250 VAC, 100K cycles [1] [2]
3 A at 250 VAC general use, 100 K cycles [1] [2]
3 A at 30 VDC resistive, 100K cycles [1] [2]
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 107
1 x 105 at 10 A 250 VAC Res.
Operate Time (max.)
8 ms at nominal coil voltage
Release Time (max.)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
1000 Vrms contact to contact
(at sea level for 1 min.) 4000 Vrms contact to coil
Insulation Resistance
1 x 109 ohms minimum at 500 VDC
Dropout
Greater than 5% of nominal coil voltage
Ambient Temperature
Operating
At nominal coil voltage
-40°C (-40°F) to 70°C (158°F) standard
-40°C (-40°F) to 85°C (185°F) sensitive
-40°C (-40°F) to 105°C (221°F)
Storage
Vibration
Shock
Operating
VDE
Material
Resistance
Form A N.O.: 5 A 250 VAC [1] [2]
Form C N.O.: 5 A 250 VAC [1] [2]
Form C N.C.: 3 A 250 VAC [1] [2]
Silver cadmium oxide [1] or silver nickel [2].
Gold plating available.
<100 milliohms initially
COIL
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
Temperature
253 mW (Standard Coil)
113 mW (Sensitive Coil)
1.1 W at 20°C (68°F)
0.062" (1.5 mm) DA at 10–55 Hz
Mechanical
10 g for 11 ms 1/2 sine pulse
(no contact opening >100 usec)
100 g for 11 ms 1/2 sine pulse
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
7 grams
Packing unit in pcs
100 per styropor tray / 1000 per carton box
NOTES
40°C (72°F) standard coil
20°C (36°F) sensitive coil
1. All values at 20°C (68°F).
Max. 105°C (221°F)
3. Specifications subject to change without notice.
ZETTLER
2. Relay may pull in with less than “Must Operate” value.
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-09-21
AZ940
RELAY ORDERING DATA
COIL SPECIFICATIONS – Standard Coil (SPDT and SPST)
Nominal Coil
VDC
3
ORDER NUMBER*
Must Operate
VDC
2.3
Max. Continuous
VDC
4.7
Coil Resistance
Ohm ± 10%
20
5
3.8
7.7
55
AZ940–1C–5D
6
4.5
9.4
80
AZ940–1C–6D
AZ940–1C–3D
9
6.8
14.0
180
AZ940–1C–9D
12
9.0
18.7
320
AZ940–1C–12D
18
13.5
28.1
720
AZ940–1C–18D
24
18.0
37.5
1,280
AZ940–1C–24D
* Substitute “1A” for “1C” to indicate 1 Form A contacts. Add suffix “B” to “1A” or “1C” for silver nickel contacts.
Add suffix “E” at the end of order number for sealed version. Add suffix “G” for gold plated contacts.
COIL SPECIFICATIONS – Sensitive Coil (SPST)
Nominal Coil
VDC
3
ORDER NUMBER**
Must Operate
VDC
2.3
Max. Continuous
VDC
7.0
Coil Resistance
Ohm ± 10%
45
5
3.8
11.7
125
AZ940–1A–5DS
6
4.5
14.0
180
AZ940–1A–6DS
9
6.8
20.9
400
AZ940–1A–9DS
12
9.0
28.1
720
AZ940–1A–12DS
18
13.5
41.9
1,600
AZ940–1A–18DS
24
18.0
55.5
2,800
AZ940–1A–24DS
AZ940–1A–3DS
** Add suffix “B” to “1A” for silver nickel contacts.
Add suffix “E” at the end of order number for sealed version. Add suffix “G” for gold plated contacts.
MECHANICAL DATA
PC BOARD LAYOUT
.807
[20.50]
.400
[10.16]
.054
[1.36]
.417
[10.59]
.300
[7.62]
.058
[1.49]
.300
[7.62]
.622
[15.80]
.020
[0.51]
5 x ø .051
[ø 1.3]
.100
[2.54]
5 x.157
[4.0]
WIRING DIAGRAM
1
5
8
2 x.014±.005
[0.35±0.12]
5 x.028±.005
[0.76±0.12]
1
FORM A
5
16
FORM C
8
3 x.012±.005
[0.31±0.12]
10
VIEWED TOWARD TERMINALS
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
ZETTLER
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2005-09-21
Similar pages