Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: Date: B32921 ... B32926 May 2005 © EPCOS AG 2006. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. Please read "Important notes" on page 9. EMI suppression capacitors (MKP) B32921 ... B32926 X2 / 305 VAC Typical applications X2 class for interference suppression "Across the line" applications Dimensional drawing Climatic Max. operating temperature: 125 °C Climatic category (IEC 60068-1): 40/105/56 Construction Dielectric: polypropylene (MKP) Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) Dimensions in mm Features Very small dimensions Self-healing properties Terminals Parallel wire leads, lead-free tinned Standard lead lengths: 6 1 mm Special lead lengths available on request Marking Manufacturer's logo, lot number, date code, rated capacitance (coded), cap. tolerance (code letter), rated AC voltage, series number, sub-class (X2), dielectric code (MKP), climatic category, passive flammability category, approvals. Lead spacing ±0.4 Lead diameter Type d1 10 15 22.5 27.5 37.5 0.6 0.8 0.8 0.8 1.0 Marking examples = 10 mm Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For taping details, refer to chapter "Taping and packing". B32921 B32922 B32923 B32924 B32926 ≥15 mm/CR≤1 µF = 22.5, 27.5, 37.5 mm/CR>1 µF Approvals Marks of conformity Standards EN 132400, IEC 60384-14 Certificate 40005536/40010694 UL 1414 / UL 1283 CSA C22.2 No.1 / No. 8 CQC (GB/T 14472-1998) E97863 / E157153 E97863 / E157153 (approved by UL) CQC001007-14859 2 B32921 ... B32926 X2 / 305 VAC Overview of available types Lead spacing 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm Type B32922 B32923 B32924 B32926 B32921 CR (µF) 0.010 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.56 0.68 0.82 1.0 1.5 2.2 3.3 4.7 5.6 6.8 8.2 10 3 B32921 ... B32926 X2 / 305 VAC Ordering codes and packing units Lead spacing CR mm 10 15 µF 0.010 0.022 0.033 0.047 0.047 0.068 0.068 0.10 0.10 0.033 0.047 0.068 0.068 0.10 0.10 0.15 0.15 0.22 0.22 0.22 0.22 0.33 0.33 0.33 0.33 0.33 0.47 0.56 0.68 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 5.0 × 10.5 × 18.0 7.0 × 12.5 × 18.0 6.0 × 12.0 × 18.0 8.5 × 14.5 × 18.0 8.0 × 14.0 × 18.0 7.0 × 12.5 × 18.0 8.0 × 14.0 × 18.0 9.0 × 17.5 × 18.0 13.0 × 14.0 × 18.0 8.0 × 14.0 × 18.0 8.5 × 14.5 × 18.0 13.0 × 14.0 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% Ordering code (composition see below) B32921C3103+*** B32921C3223+*** B32921C3333+*** B32921C3473+*** B32921A2473+*** B32921A2683M*** B32921C3683+*** B32921A2104M*** B32921C3104M*** B32922C3333+*** B32922C3473+*** B32922A2683+*** B32922C3683+*** B32922A2104+*** B32922C3104+*** B32922A2154+*** B32922C3154+*** B32922A2224+*** B32922T2224+*** B32922C3224+*** B32922T3224+*** B32922A2334+*** B32922T2334+*** B32922C3334M*** B32922D3334+*** B32922T3334+*** B32922C3474+*** B32922C3564+*** B32922C3684M*** Ammo Reel Untaped pack pcs./unit pcs./unit pcs./unit 1000 1000 1000 830 680 680 680 680 680 1170 1170 960 1170 960 1170 830 960 680 730 830 730 640 730 680 640 1700 1700 1700 1300 1100 1100 1100 1100 1100 1300 1300 1100 1300 1100 1300 900 1100 700 750 900 750 700 500 750 700 500 700 550 550 *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Preferred types (Closer tolerances on request) 4 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 500 1000 500 500 300 500 500 300 500 250 250 B32921 ... B32926 X2 / 305 VAC Ordering codes and packing units Lead spacing CR mm 22.5 µF 0.33 0.33 0.33 0.33 0.47 0.47 0.47 0.56 0.68 0.68 0.68 0.82 1.0 1.0 1.5 1.5 2.2 Max. dimensions w×h×l mm 8.5 × 16.5 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 7.5 × 14.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 8.5 × 16.5 × 26.5 8.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 10.5 × 20.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 12.0 × 22.0 × 26.5 11.0 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% Ordering code (composition see below) B32923A2334+*** B32923C3334M*** B32923D3334+*** B32923T3334+*** B32923A2474M*** B32923B2474+*** B32923C3474+*** B32923C3564M*** B32923A2684M*** B32923B2684+*** B32923C3684+*** B32923C3824M*** B32923A2105M*** B32923C3105+*** B32923C3155M*** B32923D3155+*** B32923C3225+*** Ammo Reel Untaped pack pcs./unit pcs./unit pcs./unit 480 500 510 680 700 720 580 600 630 550 500 570 480 500 510 390 400 540 480 500 510 480 500 510 390 400 540 390 400 540 390 400 540 390 400 540 450 370 350 510 450 260 260 *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Preferred types (Closer tolerances on request) 5 B32921 ... B32926 X2 / 305 VAC Ordering codes and packing units Lead spacing CR mm 27.5 37.5 µF 0.68 0.82 1.0 1.0 1.5 1.5 1.5 2.2 2.2 3.3 3.3 3.3 4.7 4.7 4.7 5.6 2.2 3.3 3.3 4.7 4.7 5.6 5.6 6.8 6.8 8.2 8.2 10.0 Max. dimensions w×h×l mm 11.0 × 19.0 × 31.5 11.0 × 19.0 × 31.5 11.0 × 21.0 × 31.5 11.0 × 19.0 × 31.5 13.5 × 23.0 × 31.5 14.0 × 24.5 × 31.5 12.5 × 21.5 × 31.5 18.0 × 27.5 × 31.5 14.0 × 24.5 × 31.5 21.0 × 31.0 × 31.5 18.0 × 27.5 × 31.5 16.0 × 32.0 × 31.5 22.0 × 36.5 × 31.5 18.0 × 33.0 × 31.5 21.0 × 31.0 × 31.5 22.0 × 36.5 × 31.5 14.0 × 25.0 × 41.5 18.0 × 32.5 × 41.5 16.0 × 28.5 × 41.5 20.0 × 39.5 × 41.5 18.0 × 32.5 × 41.5 20.0 × 39.5 × 41.5 18.0 × 32.5 × 41.5 28.0 × 42.5 × 41.5 20.0 × 39.5 × 41.5 28.0 × 42.5 × 41.5 20.0 × 39.5 × 41.5 28.0 × 42.5 × 41.5 Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% (Closer tolerances on request) Ordering code (composition see below) B32924C3684+*** B32924C3824+*** B32924A2105+*** B32924C3105+*** B32924A2155M*** B32924B2155+*** B32924C3155+*** B32924A2225+*** B32924C3225+*** B32924A2335M*** B32924C3335M*** B32924D3335+*** B32924A2475M*** B32924C3475M*** B32924D3475M*** B32924C3565+*** B32926C3225+*** B32926A2335+*** B32926C3335+*** B32926A2475M*** B32926C3475+*** B32926A2565M*** B32926C3565+*** B32926A2685M*** B32926C3685+*** B32926A2825M*** B32926C3825+*** B32926C3106+*** Ammo Reel Untaped pack pcs./unit pcs./unit pcs./unit 350 320 350 320 350 320 350 320 250 260 260 300 280 200 260 180 200 220 160 200 180 160 115 90 100 75 90 75 90 55 75 55 55 55 *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Preferred types 6 B32921 ... B32926 X2 / 305 VAC Technical data Standard version (A/B/T): Miniaturized version (C/D): B3292*A.... / B3292*B.... / B3292*T.... B3292*C.... / B3292*D.... (preferred types) Max. operating temperature Top,max Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Passive flammability category to IEC 40 (CO) 752 Maximum continuous AC voltage V AC Rated AC voltage (IEC 60384-14) Maximum continuous DC voltage V DC Operating AC voltage V op at high temperature Damp heat test Limit values after damp heat test +125 °C (for C R ≤1 µF with A/B/T version) +110 °C (for C R >1 µF or C/D version) CR≤0.1 µF 0.1µF<CR ≤2.2 µF CR >2.2 µF at 1 kHz 1.0 1.0 2.0 100 kHz 5.0 CR≤0.33 µF CR>0.33 µF 100 000 MΩ 30 000 s 2121 V, 2 s B 310 V (50/60 Hz) 305 V (50/60 Hz) 760 V (630 V for C/D version) TA ≤ 110 °C Vop = VAC (continuously) TA ≤ 110 °C Vop = 1.25 VAC (1000 h) 110 °C <TA ≤ 125 °C Vop = VAC (1000 h) (only for A/B/T version) 56 days / 40 °C / 93% relative humidity Capacitance change ∆C/C ≤ 5% Dissipation factor change ∆ tan δ ≤ 0.5 10-3 (at 1 kHz) Insulation resistance Rins ≤ 1.0 10-3 (at 10 kHz) or time constant τ = CR Rins ≥ 50% of minimum as-delivered values 7 B32921 ... B32926 X2 / 305 VAC Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V 2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values Lead 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm spacing Version A/B/T C/D A/B/T C/D A/B/T C/D A/B/T C/D A/B/T C/D dV/dt in 550 475 400 340 200 170 150 120 100 80 V/µs k0 in 473000 408500 344000 292400 172000 146200 129000 103200 86000 68800 V2/µs Impedance Z versus frequency f (typical values) 8 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, Baoke, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 9 of 9