Series JW High Inrush 10 & 16 Amp Rockers Toggles General Specifications Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical Capacity (Resistive Load) B Power Level: 10A @ 125/250V AC for JWM & JWMW models; 10A @ 30V DC for JWMW; 16A @ 125/250V AC for JWL & JWLW models; 5A @ 72V DC for telecommunication applications Other Ratings Contact Resistance: 10 milliohms maximum for JWM & JWMW; 20 milliohms maximum for JWL & JWLW Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 25,000 operations minimum Electrical Life: 25,000 operations minimum Nominal Operating Force: JWM & JWMW Single Pole 3.92N & Double Pole 7.84N JWL Single Pole 5.00N & Double Pole 10.00N; JWLW Double Pole 10.00N Angle of Throw: 26° Materials & Finishes Rocker: Housing/Frame & Barrier: Interior Seal for JWM & JWL: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Installation Soldering Time & Temperature: Polyphenylene ether (UL94V-0) Polyamide (UL94V-0) Polyphenylene sulfide (UL94V-0) Case/Base: Contacts: Terminals: Melamine (UL94V-0) Silver alloy with silver plating Brass with silver plating –25°C through +70°C (–13°F through +158°F) for JWM & JWL; –25°C through +85°C (–13°F through +185°F) for panel seal JWMW & JWLW models 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) IP67 of IEC60529 standard for panel seal JWMW & JWLW models; dust resistant inner seal for others Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 for rocker, housing, seal & case/base of JWL, JWM, JWMW & JWLW models TV Ratings for UL & CSA: JWM (TV-5) Overload Test @ 120V AC for 50 operations: Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A. JWM (TV-5) Endurance Test @ 120V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A. JWL (TV-8) Overload Test @ 120V AC for 50 operations: Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A. JWL (TV-8) Endurance Test @ 120V AC for 25,000 operations: Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A. UL: File No. E44145 JWM & JWMW models recognized at 10A @ 250V AC. JWMW recognized at 10A @ 30V DC. JWL & JWLW models recognized at 16A @ 250V AC; JWL at 5A @ 72V DC. Models below recognized only when ordered with marking on switch. JWMW: add “/U” to end of part number to order UL mark on switch; add “/CUL” to end of part number to order cULus mark on switch. JWL: add “/U-DC” to end of part number to request UL rating on DC rated switch. CSA: File No. 023535_0_000 JWM & JWMW models certified at 10A @ 250V AC; JWL models certified at 16A @ 250V AC . VDE: B40 License No. 115637 JWM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC; JWL models approved at steady state inrush 128A, resistive 16A, & motor load 8A all at 250V AC. Note: JWM & JWL Double Pole, Single Throw models approved only with the international ON-OFF symbols on the actuator. www.nkk.com Series JW Toggles Distinctive Characteristics B Pushbuttons Industry’s first molded rocker with TV rating. Designed to handle large inrush current, with high electrical capacity of 10 and 16 Amps. JWM models certified for TV-5 rating and JWL models for TV-8 rating. Rockers High Inrush 10 & 16 Amp Rockers Programmable Illuminated PB JWMW and JWLW panel seal versions meet IP67 of IEC60529 Standards (similar to NEMA 4 and 6). Prominent external insulating barriers increase insulation resistance and dielectric strength. Keylocks Uniquely constructed to break light contact welds. Increased electrical life with specially designed plate to minimize contact bounce. Rotaries Constructed for dust resistance with interior cover between actuator and contact area. Slides Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Tactiles Solder lug/quick connect terminals can be used with connector. Tilt Housing and case of heat resistant resin meet UL94V-0 standard. Supplement Accessories Indicators Touch Actual Size JWM www.nkk.com B41 High Inrush 10 & 16 Amp Rockers TYPICAL SWITCH ORDERING EXAMPLE JW B LW 2 1 R A 1 Ratings A Housing Colors Barrier Types M 10A @ 125/250V AC MW Panel Seal 10A @ 125/250V AC R L 16A @ 125/250V AC B LW Panel Seal 16A @ 125/250V AC Note: JWMW & JWLW combine with code R only. Note: JWMW & JWLW available with black only. Cap Colors Barrier Colors Poles 1 SPST SPDT 2 DPST DPDT OFF 2 ON NONE ON B Ivory With Barrier H Gray Black A Black B Ivory B Ivory C Red H Gray H Gray Note: Wire harness & cable assemblies offered only in Americas Inscription Orientation Circuits NONE No Barrier A No Code ON Black Note: JWMW & JWLW available with black or red caps only. Notes: DPST must have international ON-OFF symbols for VDE approval. JWLW available in DPST & DPDT only. 1 A IMPORTANT: No Inscription 1 Horizontal 2 Vertical Standard markings for JWM & JWL: TV Rating, UL, CSA & VDE. Standard marking for JWLW: cULus. Specific models, ratings, & ordering instructions for international approvals are noted on General Specifications page. These are inscriptions for Single Throw models only. Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series JW Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE JWLW21RA1A Accessories Indicators Black Rocker Cap with International ON-OFF Symbols in Horizontal Orientation Black Housing Supplement DPST ON-NONE-OFF Circuit B42 16A @ 125/250V AC www.nkk.com Series JW Power Level 10A @ 125/250V AC MW Panel Seal Power Level 10A @ 125/250V AC L Power Level 16A @ 125/250V AC LW Panel Seal Power Level 16A @ 125/250V AC POLES & CIRCUITS Rocker Position Connected Terminals Throw & Schematics Note: Terminal numbers are not actually on the switch. Actuator positions oriented with switch part number facing front. Down Center Up Down Center Up JWM11 JWMW11 JWL11 ON NONE OFF 1-1b OPEN OPEN SP JWM12 JWMW12 JWL12 ON NONE ON 1-1b OPEN 1-1a SPDT DP JWM21 JWMW21 JWL21 JWLW21 ON NONE OFF 1-1b 2-2b OPEN OPEN DPST JWM22 JWMW22 JWL22 JWLW22 ON 1-1b 2-2b OPEN SP DP 1 (COM) SPST 1b 1 (COM) NONE ON 1a 1 1b (COM) 2 1b 1-1a 2-2a 1 DPDT Keylocks Model 2b (COM) 1a 1b 2 2a Rotaries Pole B Pushbuttons M Programmable Illuminated PB RATINGS Rockers Toggles High Inrush 10 & 16 Amp Rockers 2b B No Barrier With Barrier Tactiles R Slides BARRIER TYPES & COLORS Tilt Barrier type designates that either AT217 (for JWM) or AT218 (for JWL) is factory assembled. Dimensions for barriers are shown in the Accessories section. Barrier Colors Available: JWMW and JWLW panel seal devices have exterior seal of acrylonitrile butadiene rubber covering the flange. Finish: Matte A B Black Barrier Material: Polyamide H Ivory Gray Indicators No-barrier type has a flat flange which is an integral part of the switch. Flange/Housing Material: Polyamide JWL Finish: Matte CAP COLORS Cap Colors Available: Cap Material: Polyphenelene Oxide Finish: Matte A Black B Ivory C Red H Gray Rocker cap is an integral part of the switch and not available separately. JWMW and JWLW available with black or red caps only. www.nkk.com Touch JWM B43 Accessories JWL Supplement JWM Series JW INSCRIPTIONS No Code B 1 No Inscription Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles High Inrush 10 & 16 Amp Rockers DPST models without inscriptions do not have VDE approval. Inscription for Horizontal Mounting 2 Inscription for Vertical Mounting The IEC symbols for On-Off are supplied with Single Throw models only. Orientation of inscription must be selected. Inscription Colors: Black ink on Ivory or Gray cap. White ink on Black or Red cap. Contact factory for other inscriptions. HOUSING Material: Polyamide Colors Available: Finish: Matte JWMW and JWLW panel seal models available with black housing only. A B Black Ivory H Gray Rotaries TERMINALS Solder Lug/Quick Connect .110” (2.8mm) Slides Epoxy Seal (3.2) .126 (7.5) .295 Epoxy Seal JWL & JWLW (0.6) R (2.8) .024 .110 (1.6) .063 Thk = (0.5) .020 Tactiles JWM & JWMW Solder Lug/Quick Connect .187” (4.75mm) (7.5) .295 (1.5) R .059 (0.65) R .026 Thk = (0.8) .031 (4.75) .187 PANEL CUTOUTS Touch Tilt Panel Thickness Range Without Barrier (JWM & JWMW): .039” ~ .157” (1.0mm ~ 4.0mm) With Barrier (JWM): .024” ~ .126” (0.6mm ~ 3.2mm) (25.0) .984 (24.0) .945 JWM JWMW (15.4) .606 Panel Thickness Range Without Barrier (JWL & JWLW): .039” ~ .157” (1.0mm ~ 4.0mm) With Barrier (JWL): .024” ~ .126” (0.6mm ~ 3.2mm) JWL JWLW (20.5) .807 B44 (30.7) 1.209 (29.5) 1.161 Supplement Accessories Indicators (15.4) .606 www.nkk.com (20.5) .807 Toggles Series JW High Inrush 10 & 16 Amp Rockers TYPICAL SWITCH DIMENSIONS FOR JWM & JWMW No Barrier • 10 Amp B (16.4) .646 COM 2a (0.5) Typ .020 (2.0) .079 (21.5) .846 (27.0) 1.063 1a (2.8) Typ .110 (6.2) .244 (15.4) .606 (7.5) .295 JWM11RC1A Single & Double Pole With Barrier • 10 Amp 2b 1b 2 1 COM COM 1a 2a (0.5) Typ .020 (13.6) .535 (18.0) .709 (22.2) .874 (7.2) .283 (18.9) .744 (2.8) Typ .110 (6.2) .244 (15.4) .606 (7.5) .295 (30.0) 1.181 JWM11BCA-H Single & Double Pole Panel Seal • No Barrier • 10 Amp (15.0) .591 (7.0) .276 Touch Part No. Slides (7.7) Typ .303 (22.6) .890 (25.0) .984 Rotaries (15.0) .591 Part No. (19.6) .772 Pushbuttons 1 COM Tactiles (13.6) .535 (18.0) .709 1b Programmable Illuminated PB 26° 2b 2 Keylocks (7.7) Typ .303 (22.6) .890 Tilt (19.6) .772 (15.0) .591 (6.0) .236 Part No. Rockers Single & Double Pole (16.4) .646 1b 1 COM COM 2a 1a (0.5) Typ .020 (13.6) .535 (21.0) .827 (3.0) .118 (21.5) .846 (6.2) .244 (15.4) .606 (7.5) .295 (29.6) 1.165 Indicators 26° 2b 2 (2.8) Typ .110 Accessories (7.7) Typ .303 (22.6) .890 JWMW22RCA Supplement (19.6) .772 Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. www.nkk.com B45 Toggles Series JW High Inrush 10 & 16 Amp Rockers TYPICAL SWITCH DIMENSIONS FOR JWL & JWLW Single & Double Pole B (24.4) .961 (20.0) .787 (9.8) Typ .386 (28.0) 1.102 26° 2b 1b 2 1 COM (20.2) .795 Programmable Illuminated PB Keylocks (7.0) .276 Part No. Pushbuttons Rockers No Barrier • 16 Amp (32.0) 1.260 COM 2a 1a (0.8) Typ .031 (17.6) .693 JWL21RC2A (4.75) Typ .187 (2.0) .079 (23.0) .906 (24.0) .945 (9.0) .354 (20.5) .807 (7.5) .295 Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. With Barrier • 16 Amp Single & Double Pole (20.0) .787 Rotaries Part No. (24.4) .961 (9.8) Typ .386 (28.0) 1.102 (29.0) 1.142 2b 1b 2 1 Slides 2a (0.8) Typ .031 (17.6) .693 Tactiles (23.0) .906 (27.2) 1.071 (21.4) .843 1a (4.75) Typ .187 (9.0) .354 (20.5) .807 (7.5) .295 Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a. Tilt JWL11BCA-H (8.15) .321 (35.0) 1.378 COM COM Double Pole Single Throw Touch Panel Seal • 16 Amp • Inscription (7.9) .311 Part No. (4.75) Typ .187 Indicators (0.8) Typ .031 (9.8) .386 (24.4) .961 2b 1b 2 1 (28.0) 1.102 26° (37.3) 1.469 COM Accessories (20.2) .795 2a Supplement (17.6) .693 (27.0) 1.063 (2.7) .106 JWLW21RA1A B46 www.nkk.com COM (21.3) .839 (7.5) .295 1a (9.0) .354 (20.0) .787 Series JW Toggles High Inrush 10 & 16 Amp Rockers TYPICAL SWITCH DIMENSIONS FOR JWLW Panel Seal • 16 Amp • No Inscription (7.9) .311 Part No. B (4.75) Typ .187 26° 2b 1b 2 1 (37.3) 1.469 COM (20.2) .795 2a 1a (9.0) .354 (20.0) .787 (17.6) .693 (27.0) 1.063 COM (2.7) .106 (21.3) .839 Programmable Illuminated PB (24.4) .961 (9.8) Typ .386 (28.0) 1.102 Pushbuttons (0.8) Typ .031 (7.5) .295 JWLW22RAA Keylocks OPTIONAL DUST COVER AT4126 Dust Cover for JWL Rocker –10° ~ +70°C (+14°F ~ +158°F) Loses pliability below 0°C (+32°F) Slides Recommended Temperature Range: Lid: Clear Polyvinyl Chloride Base: Black Polyamide Rotaries When installed, the Dust Cover protects the switch from an environment containing small particles and dust. The switch is operable with the Dust Cover in place. Materials: Rockers Double Pole Double Throw Tactiles Recommended Panel Thickness: .031” ~ .134” (0.8mm ~ 3.4mm) Tilt Assembly Instructions: 1. Insert bottom of switch through the base until the tabs lock into place. Touch 2. Snap the switch into the panel. (22.2) .874 Top (8.6) .339 (2.6) .102 Side Indicators 3. Seat the lid into the grooves of the base. Groove (33.0) 1.299 Bottom Lid Base Switch Notes Supplement 1. The dust cover is not for use with JWLW. Groove 2. The dust cover cannot be used with the barrier option. www.nkk.com Accessories (42.0) 1.654 B47 Toggles Series JW High Inrush 10 & 16 Amp Rockers PRECAUTIONS FOR HANDLING & STORAGE FOR JWMW/LW (PANEL SEAL TYPES) B • Do not install switch where heavy dust collection occurs. Dust build-up under rocker may affect switch actuation. • Do not actuate switch if submerged in water or oil. 30° • Installation is not recommended on horizontal surface in an environment where frequent splashing of water may occur. In such an environment, a minimum 30° angle installation is advisable. If there is a possibility of freezing, install vertically so no moisture will be retained within switch housing. Panel Mounting Incorrect Correct • Before snapping a switch into the panel, align the gasket evenly under bezel of the switch. • When mounting into a panel, apply equal pressure to sides of bezel and insert parallel to panel. • After mounting a switch, be sure there are no gaps between switch and panel. Lightly push into panel. • After installing into panel, do not apply excessive force. • After panel installation and wiring is completed, do not apply force horizontally or vertically from behind panel. • Behind the panel, cut area should be squared. If front of panel is painted, do not allow any paint to collect in corners of cutout to prevent level mounting. • Avoid reinstalling a switch once it has been mounted in a panel. This may cause deterioration of panel sealability. Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Operating Environment B48 www.nkk.com Clean Edges