ON NL27WZ86USG Dual 2−input exclusive−or gate Datasheet

NL27WZ86
Dual 2−Input Exclusive−OR
Gate
The NL27WZ86 is a high performance dual 2−input Exclusive−OR
Gate operating from a 1.65 V to 5.5 V supply.
Features
•
•
•
•
•
•
•
•
•
http://onsemi.com
Extremely High Speed: tPD 2.4 ns (typical) at VCC = 5.0 V
Designed for 1.65 V to 5.5 V VCC Operation
Over Voltage Tolerant Inputs and Outputs
LVTTL Compatible − Interface Capability With 5.0 V TTL Logic
with VCC = 3.0 V
LVCMOS Compatible
24 mA Balanced Output Sink and Source Capability
Near Zero Static Supply Current Substantially Reduces System
Power Requirements
Replacement for NC7WZ86
Pb−Free Package is Available
A1
1
8
VCC
B1
2
7
Y1
Y2
3
6
B2
MARKING
DIAGRAM
8
8
1
1
L8
= Device Code
M
= Date Code*
G
= Pb−Free Package
(Note: Microdot may be in either location)
*Date Code orientation may vary depending
upon manufacturing location.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
A1
GND
5
4
L8 M G
G
US8
US SUFFIX
CASE 493
=1
Y1
B1
A2
A2
Y2
B2
Figure 2. Logic Symbol
Figure 1. Pinout (Top View)
PIN ASSIGNMENT
Pin
Function
1
A1
2
B1
3
Y2
4
GND
A
B
Y
5
A2
L
L
L
6
B2
L
H
H
7
Y1
H
L
H
8
VCC
H
H
L
© Semiconductor Components Industries, LLC, 2005
September, 2005 − Rev. 3
FUNCTION TABLE
Input
Output
Y=A+B
1
Publication Order Number:
NL27WZ86/D
NL27WZ86
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
DC Supply Voltage
*0.5 to )7.0
V
VI
DC Input Voltage
*0.5 to )7.0
V
VO
DC Output Voltage
*0.5 to )7.0
V
IIK
DC Input Diode Current
VI < GND
*50
mA
IOK
DC Output Diode Current
VO < GND
*50
mA
IO
DC Output Sink Current
$50
mA
ICC
DC Supply Current per Supply Pin
$100
mA
IGND
DC Ground Current per Ground Pin
$100
mA
TSTG
Storage Temperature Range
*65 to )150
_C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
TJ
Junction Temperature under Bias
qJA
Thermal Resistance
PD
Power Dissipation in Still Air at 85_C
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ESD Withstand Voltage
(Note 1)
260
_C
)150
_C
250
_C/W
250
mW
Level 1
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Human Body Model (Note 2)
Machine Model (Note 3)
Charged Device Model (Note 4)
> 2000
> 200
N/A
V
Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those
indicated may adversely affect device reliability. Functional operation under absolute maximum−rated conditions is not implied. Functional
operation should be restricted to the Recommended Operating Conditions.
1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace with no air flow.
2. Tested to EIA/JESD22−A114−A.
3. Tested to EIA/JESD22−A115−A.
4. Tested to JESD22−C101−A.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
VCC
Supply Voltage
VI
Input Voltage
VO
Output Voltage
TA
Operating Free−Air Temperature
Dt/DV
Input Transition Rise or Fall Rate
Min
Max
Unit
1.65
1.5
5.5
5.5
V
(Note 5)
0
5.5
V
(HIGH or LOW State)
0
5.5
V
*40
)125
_C
0
0
0
0
20
20
10
5
ns/V
Operating
Data Retention Only
VCC = 1.8 V $0.15 V
VCC = 2.5 V $0.2 V
VCC = 3.0 V $0.3 V
VCC = 5.0 V $0.5 V
5. Unused inputs may not be left open. All inputs must be tied to a high− or low−logic input voltage level.
http://onsemi.com
2
NL27WZ86
DC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
TA = 255C
VCC
(V)
Min
0.75 VCC
0.7 VCC
VIH
High−Level Input
Voltage
1.65 to 1.95
2.3 to 5.5
VIL
Low−Level Input
Voltage
1.65 to 1.95
2.3 to 5.5
VOH
High−Level Output
Voltage
VIN = VIH
VOL
Low−Level Output
Voltage
VIN = VIL
IIN
Input Leakage Current
IOFF
Power Off Leakage
Current
ICC
Quiescent Supply
Current
Typ
*405C v TA v 855C
Max
Min
Max
Unit
0.75 VCC
0.7 VCC
0.25 VCC
0.3 VCC
Condition
V
0.25 VCC
0.3 VCC
V
1.65
1.8
2.3
3.0
4.5
1.55
1.7
2.2
2.9
4.4
1.65
1.8
2.3
3.0
4.5
1.55
1.7
2.2
2.9
4.4
V
IOH = −100 mA
1.65
2.3
3.0
3.0
4.5
1.29
1.9
2.4
2.3
3.8
1.52
2.15
2.80
2.68
4.20
1.29
1.9
2.4
2.3
3.8
V
IOH = −4 mA
IOH = −8 mA
IOH = −16 mA
IOH = −24 mA
IOH = −32 mA
1.65
1.8
2.3
3.0
4.5
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
V
IOL = 100 mA
1.65
2.3
3.0
3.0
4.5
0.08
0.10
0.15
0.22
0.22
0.24
0.30
0.40
0.55
0.55
0.24
0.30
0.40
0.55
0.55
V
IOL = 4 mA
IOL = 8 mA
IOL = 16 mA
IOL = 24 mA
IOL = 32 mA
0 to 5.5
$1.0
$1.0
mA
0 V v VIN v 5.5 V
0.0
1.0
10
mA
VIN or VOUT = 5.5 V
1.65 to 5.5
1.0
10
mA
VIN = 5.5 V, GND
AC ELECTRICAL CHARACTERISTICS tR = tF = 3.0 ns
VCC
Symbol
tPLH
tPHL
Parameter
Propagation Delay
(Figure 3 and 4)
TA = 25_C
*40_C v TA v 125_C
Condition
(V)
Min
Typ
Max
Min
Max
Unit
RL = 1 MW, CL = 15 pF
1.8 $ 0.15
2.0
7.9
9.0
2.0
10.5
ns
RL = 1 MW, CL = 15 pF
2.5 $ 0.2
1.2
4.1
7.0
1.2
7.5
RL = 1 MW, CL = 15 pF
3.3 $ 0.3
0.8
3.0
4.8
0.8
5.2
1.2
3.8
5.4
1.2
5.9
0.5
2.2
3.5
0.5
3.8
0.8
2.9
4.2
1.0
4.6
RL = 500 W, CL = 50 pF
RL = 1 MW, CL = 15 pF
5.0 $ 0.5
RL = 500 W, CL = 50 pF
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
Condition
Typical
Unit
2.5
pF
pF
CIN
Input Capacitance
VCC = 5.5 V, VI = 0 V or VCC
CPD
Power Dissipation Capacitance
(Note 6)
10 MHz, VCC = 3.3 V, VI = 0 V or VCC
9
10 MHz, VCC = 5.5 V, VI = 0 V or VCC
11
6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic
power consumption; PD = CPD VCC2 fin + ICC VCC.
http://onsemi.com
3
NL27WZ86
tf = 3 ns
tf = 3 ns
90%
INPUT
A and B
50%
VCC or GND
VCC
90%
50%
10%
10%
tPHL
OUTPUT
INPUT
GND
RL
CL
tPLH
VOH
OUTPUT Y
50%
A 1−MHz square input wave is recommended for
propagation delay tests.
50%
VOL
Figure 3. Switching Waveform
Figure 4. Test Circuit
DEVICE ORDERING INFORMATION
Device Order Number
NL27WZ86US
NL27WZ86USG
Package Type
Tape and Reel Size†
US8
178 mm, 3000 Units / Tape & Reel
US8
(Pb−Free)
178 mm, 3000 Units / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
4
NL27WZ86
PACKAGE DIMENSIONS
US8
US SUFFIX
CASE 493−02
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION “A” DOES NOT INCLUDE MOLD
FLASH, PROTRUSION OR GATE BURR.
MOLD FLASH. PROTRUSION AND GATE
BURR SHALL NOT EXCEED 0.140 MM
(0.0055”) PER SIDE.
4. DIMENSION “B” DOES NOT INCLUDE
INTER−LEAD FLASH OR PROTRUSION.
INTER−LEAD FLASH AND PROTRUSION
SHALL NOT E3XCEED 0.140 (0.0055”) PER
SIDE.
5. LEAD FINISH IS SOLDER PLATING WITH
THICKNESS OF 0.0076−0.0203 MM.
(300−800 “).
6. ALL TOLERANCE UNLESS OTHERWISE
SPECIFIED ±0.0508 (0.0002 “).
−X−
A
8
J
−Y−
5
DETAIL E
B
L
1
4
R
S
G
P
U
C
−T−
SEATING
PLANE
K
D
H
0.10 (0.004) T
N
R 0.10 TYP
0.10 (0.004)
M
T X Y
V
M
DETAIL E
F
SOLDERING FOOTPRINT*
3.8
0.5 TYP
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
1.8 TYP
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
1.0
0.3 TYP
(mm)
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
5
DIM
A
B
C
D
F
G
H
J
K
L
M
N
P
R
S
U
V
MILLIMETERS
MIN
MAX
1.90
2.10
2.20
2.40
0.60
0.90
0.17
0.25
0.20
0.35
0.50 BSC
0.40 REF
0.10
0.18
0.00
0.10
3.00
3.20
0_
6_
5_
10 _
0.23
0.34
0.23
0.33
0.37
0.47
0.60
0.80
0.12 BSC
INCHES
MIN
MAX
0.075
0.083
0.087
0.094
0.024
0.035
0.007
0.010
0.008
0.014
0.020 BSC
0.016 REF
0.004
0.007
0.000
0.004
0.118
0.126
0_
6_
5_
10 _
0.010
0.013
0.009
0.013
0.015
0.019
0.024
0.031
0.005 BSC
NL27WZ86
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
6
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
NL27WZ86/D
Similar pages