ETC1 MP9100-2.00-1 To-247 kool-pak power film resistor Datasheet

MP9100 TO-247 Kool-Pak® Power Film Resistor
TO-247 Style Power Package 100 Watt Non-Inductive Design
•
•
•
•
•
•
•
100 watt continuous power at +25°C case temperature
TO-247 package utilizes proven power semiconductor thermal solutions
Equivalent to UL94 V-O flammability rating
Excellent pulse/surge performance
Non-inductive design for high speed switching, snubbers and rf applications
Safe and reliable operation up to +175°C case temperature
Electrically isolated case
Maximum Ratings
Rating
Power Dissipation: With heat sink TC=25°C
Free Air at 25°C without heat sink
Thermal Resistance: Resistance film (J) to Case (C)
Operating and Storage Temperature Range
Single Pulse/Surge Ratings: (1)
TC = 25°C with no continuous power
applied, derate per Fig. 1
Symbol
Value
Unit
PD
100
Watts
PD
3.5
Watts
RθJC
TC,TJ, TSTG
1.5
˚C/W
-55 to +175
˚C
These products are covered by one or more
patents, also patents pending.
Derating Using Case Temperature (TC):
Duration
Energy
Units
10 µsec
0.07
Joules
100 µsec
0.25
Joules
Electrical Specifications:
All power and overload ratings are derated based
upon case temperature using the derating curve.
The case temperature is measured at the center of
the ceramic mounting surface, with the part properly
mounted and under electrical load
Temperature Coefficient:
TC referenced to +25°C, ∆R taken at +175°C
0.50 ohm and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohm, 0 to +150 ppm/°C
Derating Curve
(Fig. 1)
Inductance: 10 nH typical in series when measured at the shoulder of the lead
100
1 msec
0.9
Joules
10 msec
3.5
Joules
100 msec
15
Joules
250 msec
38
Joules
V maximum
600
volts peak
80
Capacitance: <1 pf typical without heat sink
60
DWV: 1500 V RMSAC isolation to the mounting
surface or a clip in contact with the top surface
RATED POWER OR
PULSE ENERGY, %
40
Insulation Resistance: 10,000 Megohms, min.
The resistor element is electrically isolated from
the mounting surface.
20
0
(1) For multiple pulses/surge ratings please
contact applications engineering for assistance
25
100
175
Momentary Overload: 1.5 times rated power for
5 seconds, ∆R ±(0.5 percent + 0.0005 ohm) max.,
based on a case temperature of +175°C max.
o
CASE TEMPERATURE, C
Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material,
such as thermal grease. The entire exposed ceramic portion must be in contact with the heat sink.
When screw mounting, use a Belleville washer which provides a mounting force of 150 to 300 pounds
(665 to 1330 N). Mounting torque to avoid package damage is 8 in-lbs. (0.90 N-m). If a spring clip is
used, a clip force of 4.5 to 35 pounds (20 to 155 N) is recommended
Environmental Specifications:
Standard Resistance Values:
Tolerance: 1% Standard
0.620 ± 0.010
(15.75 ± 0.26)
0.143 ± 0.004
(3.63 ± 0.10) Dia.
0.195 ± 0.010
(4.95 ± 0.26)
C
L
0.210 ± 0.010
(5.33 ± 0.26)
0.815 ± 0.010
(20.70 ± 0.26)
0.110 ± 0.030
(2.79 ± 0.76)
MP9100
50.0
1%
0.143 ± 0.015
(3.63 ± 0.38)
0.570 ± 0.050
(14.48 ± 1.27)
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
0.50
0.75
1.00
1.50
2.00
2.20
2.50
3.00
3.30
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
3.90
5.00
8.00
10.0
12.0
15.0
18.0
20.0
22.0
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
25.0
27.0
33.0
39.0
47.0
50.0
56.0
75.0
100
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
For custom values and tolerances contact
applications engineering
0.060 ± 0.004
(1.52 ± 0.10)
0.400 ± 0.010
(10.16 ± 0.26)
0.050
0.10
0.12
0.15
0.20
0.25
0.30
0.33
0.39
0.032 +0.004 / -0.010
(0.81 +0.10 / -0.026)
0.095 ± 0.010
(2.41 ± 0.26)
Ordering Information:
Parts shipped 25 per anti static plastic tube
MP9100 - 0.050 - 1%
DIMENSIONS IN INCHES AND (MILLIMETERS)
RHOPOINT COMPONENTS LTD.
Holland Road
Hurst Green
Oxted, Surrey, RH8 9AX
© 2000 Caddock Electronics, Inc.
Model Number:
Resistor Value:
(see table)
Tolerance
(1% Std)
CADDOCK
www.caddock.com
Load Stability: 2000 hours at rated power
∆R less than ±(1% +0.0005Ω)
Moisture Resistance: Mil-Std-202, Method 106,
∆R ±(0.5 percent + 0.0005 ohm) max.
Thermal Shock: Mil-Std-202, Method 107, Cond.
F, ∆R ±(0.5 percent + 0.00005 ohm) max.
Shock: 100G, Mil-Std-202, Method 213,
Cond. I, ∆R ±(0.4 percent + 0.0005 ohm) max.
Vibration, High Frequency: Mil-Std 202, Method
204, Condition D, ∆R±(0.4% +0.0005Ω) max.
Terminal Strength: Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs.,
∆R ±(0.2 percent + 0.0005 ohm) max.
Measurement Note: Resistance measurements
shall be made at 0.2 inch (5.08 mm) from the
resistor body
For more information please see our website:
Application Note: CAD-9100-1
Tel: +44 (0)1883 717988
Fax: +44 (0)1883 712938
Email: [email protected]
Website: www.rhopoint.co.uk/components/
IL-127.010
Similar pages