Keysight N9030A Pxa x-series signal analyzer Datasheet

Keysight Technologies
PXA X-Series Signal Analyzer
N9030A
3 Hz to 3.6, 8.4, 13.6, 26.5, 43, 44, or 50 GHz
Data Sheet
2 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Table of Contents
Definitions and Conditions........................................................................................ 3
Frequency and Time Specifications ......................................................................... 4
Amplitude Accuracy and Range Specifications ...................................................... 6
Dynamic Range Specifications.................................................................................. 9
PowerSuite Measurement Specifications ...............................................................16
General Specifications .............................................................................................17
Inputs and Outputs ..................................................................................................18
Other Optional Outputs........................................................................................... 21
I/Q Analyzer.............................................................................................................. 22
I/Q Analyzer – Option B25....................................................................................... 24
I/Q Analyzer – Option B40...................................................................................... 25
I/Q Analyzer – Option B85 or B1X.......................................................................... 26
Real-time spectrum analyzer (RTSA)..................................................................... 27
Related Literature ................................................................................................... 28
This data sheet is a summary of the specifications and conditions for PXA signal
analyzers. For the complete specifications guide, visit:
www.keysight.com/find/pxa_specifications
Drive your evolution
The Keysight Technologies, Inc.
future-ready PXA signal analyzer
is the evolutionary replacement
for your current high-performance
analyzer. It helps you sustain past
achievements, enhance current
designs and accelerate future innovations.
Its performance, flexibility, capability and compatibility enable
you to address demanding applications in aerospace, defense,
commercial communications and
more.
–– Reveal new levels of signal
detail with outstanding
RF performance
–– Increase test throughput
and protect your system
investments
–– Refresh legacy systems
with a highly compatible
replacement
3 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Definitions and Conditions
Specifications describe the performance of parameters covered by the product
warranty and apply to temperature ranges 0 to 55 °C, unless otherwise noted.
95th percentile values indicate the breadth of the population (approx. 2σ) of
performance tolerances expected to be met in 95 percent of the cases with
a 95 percent confidence, for any ambient temperature in the range of 20 to
30 °C. In addition to the statistical observations of a sample of instruments,
these values include the effects of the uncertainties of external calibration
references. These values are not warranted. These values are updated
occasionally if a significant change in the statistically observed behavior of
production instruments is observed.
Typical describes additional product performance information that is not
covered by the product warranty. It is performance beyond specifications that
80 percent of the units exhibit with a 95 percent confidence level over the
temperature range 20 to 30 °C. Typical performance does not include measurement uncertainty.
Nominal values indicate expected performance, or describe product performance that is useful in the application of the product, but is not covered by the
product warranty.
The analyzer will meet its specifications when:
–– The analyzer is within its calibration cycle.
–– Under auto couple control, except that Auto Sweep Time Rules = Accy.
–– For signal frequencies < 10 MHz, DC coupling applied.
–– The analyzer has been stored at an ambient temperature within the allowed
operating range for at least two hours before being turned on, if it had
previously been stored at a temperature range inside the allowed storage
range but outside the allowed operating range.
–– The analyzer has been turned on at least 30 minutes with Auto Align set
to normal, or if Auto Align is set to off or partial, alignments must have
been run recently enough to prevent an Alert message. If the Alert condition is changed from Time and Temperature to one of the disabled duration
choices, the analyzer may fail to meet specifications without informing the
user.
For the complete specifications guide, visit:
www.keysight.com/find/pxa_specifications
4 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Frequency and Time Specifications
Frequency range
DC coupled
AC coupled
Option 503
3 Hz to 3.6 GHz
10 MHz to 3.6 GHz
Option 508
3 Hz to 8.4 GHz
10 MHz to 8.4 GHz
Option 513
3 Hz to 13.6 GHz
10 MHz to 13.6 GHz
Option 526
3 Hz to 26.5 GHz
10 MHz to 26.5 GHz
Option 543
3 Hz to 43 GHz
NA
Option 544
3 Hz to 44 GHz
NA
Option 550
3 Hz to 50 GHz
NA
Band
LO multiple (N)
0
1
3 Hz to 3.6 GHz
1
1
3.5 to 8.4 GHz
2
2
8.3 to 13.6 GHz
3
2
13.5 to 17.1 GHz
4
4
17 to 26.5 GHz
5
4
26.4 to 34.5 GHz
6
8
34.4 to 50 GHz
Precision frequency reference
Accuracy
± [(time since last adjustment x aging rate) + temperature stability + calibration accuracy]
Aging rate
± 1 x 10–7 / year
± 1.5 x 10–7 / 2 years
Temperature stability
20 to 30 °C
Full temperature range
± 1.5 x 10–8
± 5 x 10–8
Achievable initial calibration accuracy
± 4 x 10–8
Example frequency reference accuracy
1 year after last adjustment 20 to 30 °C
= ± (1 x 1 x 10–7 + 1.5 x 10–8 + 4 x 10–8)
= ± 1.55 x 10–7
Residual FM
Center frequency = 1 GHz
10 Hz RBW, 10 Hz VBW
≤ (0.25 Hz x N) p-p in 20 ms nominal
See band table above for N (LO multiple)
Frequency readout accuracy (start, stop, center, marker)
± (marker frequency x frequency reference accuracy + 0.10% x span + 5% x RBW + 2 Hz + 0.5 x horizontal resolution 1)
Marker frequency counter
Accuracy
± (marker frequency x frequency reference accuracy + 0.100 Hz)
Delta counter accuracy
± (delta frequency x frequency reference accuracy + 0.141 Hz)
Counter resolution
0.001 Hz
Frequency span (FFT and swept mode)
Range
0 Hz (zero span), 10 Hz to maximum frequency of instrument
Resolution
2 Hz
Accuracy
Swept
FFT
± (0.1% x span + horizontal resolution)
± (0.1% x span + horizontal resolution)
1.
Horizontal resolution is span/(sweep points –1).
5 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Sweep time and triggering
Range
Span = 0 Hz
Span ≥ 10 Hz
1 μs to 6000 s
1 ms to 4000 s
Accuracy
Span ≥ 10 Hz, swept
Span ≥ 10 Hz, FFT
Span = 0 Hz
± 0.01% nominal
± 40% nominal
± 0.01% nominal
Sweep trigger
Free run, line, video, external 1, external 2, RF burst, periodic timer
Trigger Delay
Span = 0 Hz or FFT
Span ≥ 10 Hz, swept
Resolution
–150 to +500 ms
0 to 500 ms
0.1 μs
Time gating
Gate methods
Gate length range (except method = FFT)
Gate delay range
Gate delay jitter
Gated LO; gated video; gated FFT
1 μs to 5.0 s
0 to 100.0 s
33.3 ns p-p nominal
Sweep (trace) point range
All spans
1 to 40001
Resolution bandwidth (RBW)
Range (–3.01 dB bandwidth)
1 Hz to 3 MHz (10% steps), 4, 5, 6, 8 MHz
Bandwidth accuracy (power)
RBW range
1 Hz to 100 kHz
110 kHz to 1.0 MHz (< 3.6 GHz CF)
1.1 to 2 MHz (< 3.6 GHz CF)
2.2 to 3 MHz (< 3.6 GHz CF)
4 to 8 MHz (< 3.6 GHz CF)
± 0.5% (± 0.022 dB)
± 1.0% (± 0.044 dB)
± 0.07 dB nominal
± 0.10 dB nominal
± 0.20 dB nominal
1 Hz to 1.3 MHz
± 2% nominal
Bandwidth accuracy (–3.01 dB)
RBW range
Selectivity (–60 dB/–3 dB)
4.1:1 nominal
EMI bandwidth (CISPR compliant)
200 Hz, 9 kHz, 120 kHz, 1 MHz
(Option EMC required)
EMI bandwidth (MIL STD 461E compliant)
10 Hz, 100 Hz, 1 kHz, 10 kHz,
100 kHz, 1 MHz
(Option EMC required)
Standard
Option B25
Option B40
Option B85
Option B1X
10 MHz
25 MHz
40 MHz
85 MHz
160 MHz
Analysis bandwidth 1
Maximum bandwidth
Video bandwidth (VBW)
Range
1 Hz to 3 MHz (10% steps), 4, 5, 6, 8 MHz, and wide open (labeled 50 MHz)
Accuracy
Measurement speed
± 6% nominal (in swept mode and zero span)
2
Standard
Local measurement and display update rate
10 ms (100/s) nominal
Remote measurement and LAN transfer rate
10 ms (100/s) nominal
Marker peak search
2.5 ms nominal
Center frequency tune and transfer (RF)
43 ms nominal
Center frequency tune and transfer (μW)
69 ms nominal
Measurement/mode switching
40 ms nominal
1.
Analysis bandwidth is the instantaneous bandwidth available around a center frequency over which the input signal can be digitized for further analysis or processing in the time, frequency, or modulation domain.
2. Sweep points = 101.
6 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Amplitude Accuracy and Range Specifications
Amplitude range
Measurement range
Preamp Off
Preamp On
RF (Opt 503)
Microwave (Opt 508, 513, 526)
Millimeter-wave (Opt 543, 544, 550)
Input attenuator range
(3 Hz to 50 GHz)
Displayed average noise level (DANL) to +30 dBm
Displayed average noise level (DANL) to +30 dBm
Displayed average noise level (DANL) to +24 dBm
Displayed average noise level (DANL) to +20 dBm
0 to 70 dB in 2 dB steps
Electronic attenuator (Option EA3)
Frequency range
3 Hz to 3.6 GHz
Attenuation range
Electronic attenuator range
Full attenuation range
(mechanical + electronic)
0 to 24 dB, 1 dB steps
0 to 94 dB, 1 dB steps
Maximum safe input level
Average total power
(with and without preamp)
+30 dBm (1 W)
Peak pulse power
< 10 μs pulse width, < 1% duty cycle +50 dBm (100 W) and input attenuation ≥ 30 dB
DC volts
DC coupled
AC coupled
± 0.2 Vdc
± 100 Vdc (For frequency Option 503, 508, 513, or 526)
Display range
Log scale
0.1 to 1 dB/division in 0.1 dB steps
1 to 20 dB/division in 1 dB steps (10 display divisions)
Linear scale
10 divisions
Scale units
dBm, dBmV, dBμV, dBmA, dBμA, V, W, A
Frequency response
Specification
95th percentile (≈ 2σ)
(10 dB input attenuation, 20 to 30 °C, preselector centering applied above 3.6 GHz)
RF/MW
(Option 503, 508, 513, 526)
3 Hz to 10 MHz
10 to 20 MHz
20 MHz to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 22.0 GHz
22.0 to 26.5 GHz
± 0.46 dB
± 0.35 dB
± 0.35 dB
± 1.5 dB
± 2.0 dB
± 2.0 dB
± 2.5 dB
± 0.16 dB
± 0.39 dB
± 0.45 dB
± 0.62 dB
± 0.82 dB
Millimeter-Wave
(Option 543, 544, 550)
3 Hz to 20 MHz
20 to 50 MHz
50 MHz to 3.6 GHz
3.5 to 5.2 GHz
5.2 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 22.0 GHz
22.0 to 26.5 GHz
26.4 to 34.5 GHz
34.4 to 50 GHz
± 0.46 dB
± 0.35 dB
± 0.35 dB
± 1.7 dB
± 1.5 dB
± 2.0 dB
± 2.0 dB
± 2.0 dB
± 2.5 dB
± 2.5 dB
± 3.2 dB
± 0.19 dB
± 0.15 dB
± 0.70 dB
± 0.57 dB
± 0.54 dB
± 0.64 dB
± 0.72 dB
± 0.71 dB
± 0.93 dB
± 1.24 dB
± 0.68 dB
± 0.55 dB
± 2.0 dB
± 2.3 dB
± 2.5 dB
± 3.0 dB
± 3.5 dB
± 0.36 dB
± 0.26 dB
± 0.28 dB
± 0.64 dB
± 0.76 dB
± 0.95 dB
± 1.41 dB
± 1.61 dB
Preamp on (0 dB attenuation) (Option P03, P08, P13, P26, P43, P44, P50)
RF/MW
(Option 503, 508, 513, 526)
9 to 100 kHz
100 kHz to 50 MHz
50 MHz to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 22.0 GHz
22.0 to 26.5 GHz
7 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Millimeter-Wave
(Option 543, 544, 550)
9 to 100 kHz
100 kHz to 50 MHz
50 MHz to 3.6 GHz
3.5 to 5.2 GHz
5.2 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 22.0 GHz
22.0 to 26.5 GHz
26.4 to 34.5 GHz
34.4 to 50 GHz
Input attenuation switching uncertainty
± 0.68 dB
± 0.60 dB
± 2.0 dB
± 2.0 dB
± 2.3 dB
± 2.5 dB
± 3.0 dB
± 3.5 dB
± 3.0 dB
± 4.1 dB
± 0.40 dB
± 0.34 dB
± 0.31 dB
± 0.81 dB
± 0.70 dB
± 0.79 dB
± 0.88 dB
± 1.07 dB
± 1.03 dB
± 1.35 dB
± 1.69 dB
Specifications
Additional information
± 0.14 dB
± 0.18 dB
± 0.03 dB typical
± 0.05 dB typical
± 0.05 dB nominal
Relative to 10 dB and preamp off
At 50 MHz (reference frequency)
attenuation 12 to 40 dB
attenuation 2 to 8 dB
attenuation 0 dB
attenuation > 2 dB
3 Hz to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 26.5 GHz
26.4 to 50 GHz
± 0.3 dB nominal
± 0.5 dB nominal
± 0.7 dB nominal
± 0.7 dB nominal
± 1.0 dB nominal
Total absolute amplitude accuracy
(10 dB attenuation, 20 to 30 °C, 1 Hz ≤ RBW ≤ 1 MHz, input signal –10 to –50 dBm, all settings auto-coupled except
Auto Swp Time = Accy, any reference level, any scale, σ = nominal standard deviation)
Preamp on
(Option P03, P08, P13, P26, P43, P44
and P50)
At 50 MHz
At all frequencies
10 Hz to 3.6 GHz
± 0.24 dB
± (0.24 dB + frequency response)
± 0.19 dB (95th Percentile approx. 2σ)
At all frequencies
± (0.36 dB + frequency response)
Input voltage standing wave ratio (VSWR)
Freq Opt 503, 508, 513, 526
Freq Opt 543, 544, 550
(10 dB input attenuation)
50 MHz
10 MHz to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 26.5 GHz
26.4 to 34.5 GHz
34.4 to 50 GHz
1.07:1 nominal
1.139 (95th percentile)
1.290 (95th percentile)
1.388 (95th percentile)
1.403 (95th percentile)
1.475 (95th percentile)
NA
NA
1.025:1 nominal
1.134 (95th percentile)
1.152 (95th percentile)
1.178 (95th percentile)
1.204 (95th percentile)
1.331 (95th percentile)
1.321 (95th percentile)
1.378 (95th percentile)
Preamp on (0 dB input attenuation)
(Option P03. P08, P13, P26, P43, P44,
and P50)
10 MHz to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 26.5 GHz
26.4 to 34.5 GHz
34.4 to 50 GHz
1.45 (95th percentile)
1.54 (95th percentile)
1.57 (95th percentile)
1.48 (95th percentile)
1.54 (95th percentile)
NA
NA
1.393 nominal
1.50 (95th percentile)
1.310 (95th percentile)
1.330 (95th percentile)
1.339 (95th percentile)
1.41 (95th percentile)
1.42 (95th percentile)
8 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Resolution bandwidth switching uncertainty (referenced to 30 kHz RBW)
1 Hz to 1.5 MHz RBW
± 0.03 dB
1.6 MHz to 2.7 MHz RBW
± 0.05 dB
3 MHz RBW
± 0.10 dB
4, 5, 6, 8 MHz RBW
± 0.30 dB
Reference level
Range
Log scale
Linear scale
–170 to +30 dBm in 0.01 dB steps
707 pV to 7.07 V with 0.11% (0.01 dB) resolution
Accuracy
0 dB
Display scale switching uncertainty
Switching between linear and log
0 dB
Log scale/div switching
0 dB
Display scale fidelity
Between –10 dBm and –80 dBm input mixer level
± 0.10 dB total
± 0.04 dB typical
Below –18 dBm input mixer level
± 0.07 dB
± 0.02 dB typical
Trace detectors
Normal, peak, sample, negative peak, log power average, RMS average, and voltage average
Preamplifier
Frequency range 1
Option P03
Option P08
Option P13
Option P26
Option P43
Option P44
Option P50
9 kHz to 3.6 GHz
9 kHz to 8.4 GHz
9 kHz to 13.6 GHz
9 kHz to 26.5 GHz
9 kHz to 43 GHz
9 kHz to 44 GHz
9 kHz to 50 GHz
Gain
9 kHz to 3.6 GHz
3.6 to 26.5 GHz
26.5 to 50 GHz
+20 dB nominal
+35 dB nominal
+40 dB nominal
1.
Below 100 kHz, only 95th percentile (approx. 2σ) value for frequency response is provided.
9 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Dynamic Range Specifications
1 dB gain compression (two-tone)
Maximum power at input mixer
(At 1 kHz RBW with 100 kHz tone spacing, 20 to 30 °C)
20 to 40 MHz
–3 dBm
40 to 200 MHz
+1 dBm
200 MHz to 3.6 GHz
+3 dBm
3.6 to 16 GHz
+1 dBm
16 to 26.5 GHz
–1 dBm
26.5 to 50 GHz
Preamp on
10 MHz to 3.6 GHz
(Option P03, P08, P13, P26, P43,
3.6 to 26.5 GHz
P44, and P50)
Tone spacing 100 kHz to 20 MHz
Tone spacing > 70 MHz
Freq Option ≤ 526
Freq Option > 526
26.5 to 50 GHz
Displayed average noise level (DANL)
Specification
0 dBm typical
+3 dBm typical
+5 dBm typical
+4 dBm typical
+2 dBm typical
0 dBm nominal
–14 dBm nominal
–28 dBm nominal
–10 dBm nominal
–20 dBm nominal
–30 dBm nominal
Typical
(Input terminated, sample or average detector, averaging type = Log, 0 dB input attenuation, IF Gain = High, 1 Hz RBW, 20 to 30 °C)
RF/MW (Option 503, 508, 513, 526)
Preamp off
Preamp on
Option P03, P08, P13, P26
Normal 1/LNP enabled 2
3 Hz to 9 kHz
9 to 100 kHz
100 kHz to1 MHz
1 to 10 MHz
10 MHz to 1.2 GHz
1.2 to 2.1 GHz
2.1 to 3.0 GHz
3.0 to 3.6 GHz
3.5 to 4.2 GHz
4.2 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 16.9 GHz
16.9 to 20.0 GHz
20.0 to 26.5 GHz
100 to 200 kHz
200 to 500 kHz
0.5 to 1 MHz
1 to 10 MHz
Option P03, P08, P13, P26
10 MHz to 2.1 GHz
Option P03, P08, P13, P26
2.1 to 3.6 GHz
Option P03, P08, P13, P26
3.5 to 8.4 GHz
Option P08, P13, P26 3
Option P13, P26 3
8.3 to 13.6 GHz
3
Option P26
13.5 to 16.9 GHz
Option P26 3
16.9 to 20.0 GHz
Option P26 3
20.0 to 26.5 GHz
DANL with Noise Floor Extension (NFE) on 4
RF/MW (Option 503, 508, 513, 526)
Band 0, f > 20 MHz
Band 1
Band 2
Band 3
Band 4
Examples of effective DANL
Preamp Off
Preamp On
Frequency 20 to 30 °C
Mid-Band 0 (1.8 GHz)
–161 dBm
–171 dBm
Mid-Band 1 (5.95 GHz)
–158 dBm
–172 dBm
Mid-Band 2 (10.95 GHz)
–159 dBm
–168 dBm
Mid-Band 3 (15.3 GHz)
–152 dBm
–165 dBm
Mid-Band 4 (21.75 GHz)
–149 dBm
–160 dBm
1.
2.
3.
4.
–146 dBm/NA
–150 dBm/NA
–155 dBm/NA
–155 dBm/NA
–153 dBm/NA
–152 dBm/NA
–151 dBm/NA
–147 dBm/–153 dBm
–150 dBm/–155 dBm
–149 dBm/–155 dBm
–145 dBm/–152 dBm
–143 dBm/–151 dBm
–137 dBm/–150 dBm
–157 dBm/NA
–160 dBm/NA
–164 dBm/NA
–164 dBm/NA
–165 dBm/NA
–163 dBm/NA
–164 dBm/NA
–163 dBm/NA
–161 dBm/NA
–159 dBm/NA
–155 dBm/NA
Normal 1/LNP enabled 2
–100 dBm/NA typical
–152 dBm/NA typical
–156 dBm/NA typical
–158 dBm/NA typical
–157 dBm/NA typical
–155 dBm/NA typical
–154 dBm/NA typical
–153 dBm/NA typical
–150 dBm/–156 dBm typical
–152 dBm/–157 dBm typical
–151 dBm/–157 dBm typical
–147 dBm/–155 dBm typical
–145 dBm/–153 dBm typical
–140 dBm/–152 dBm typical
–160 dBm/NA typical
–163 dBm/NA typical
–166 dBm/NA typical
–167 dBm/NA typical
–166 dBm/NA typical
–164 dBm/NA typical
–166 dBm/NA typical
–165 dBm/NA typical
–162 dBm/NA typical
–161 dBm/NA typical
–157 dBm/NA typical
Improvement @ 95th percentile
Preamp Off
Preamp On
LNP enabled 2, 3
9 dB
10 dB
NA
10 dB
9 dB
10 dB
10 dB
10 dB
10 dB
9 dB
10 dB
10 dB
10 dB
8 dB
10 dB
LNP enabled 2, 3
NA
–162 dBm
–162 dBm
–160 dBm
–160 dBm
With the NFE (Noise Floor Extension) “Off”.
LNP (Low Noise Path) requires option LNP.
At higher frequency bands (beyond 3.6 GHz), Preamp “On” supersedes “LNP enabled”. LNP cannot operate simultaneously with preamp.
Beginning January 2015, all PXAs ship standard with the second-generation of NFE (instrument alignment based) installed as N9030A-NF2.
10 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Millimeter-Wave (Option 543, 544, 550)
Normal 1/LNP enabled 2
Normal 1/LNP enabled 2
3 Hz to 9 kHz
9 to 100 kHz
100 kHz to 1 MHz
1 to 10 MHz
10 MHz to 1.2 GHz
1.2 to 2.1 GHz
2.1 to 3 GHz
3 to 3.6 GHZ
3.5 to 4.2 GHz
4.2 to 6.6 GHz
6.6 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 14 GHz
14 to 17 GHz
17 to 22.5 GHz
22.5 to 26.5 GHz
26.4 to 34 GHz
33.9 to 37 GHz
37 to 40 GHz
40 to 46 GHz
46 to 49 GHz
49 to 50 GHz
–146 dBm/NA
–150 dBm/NA
–155 dBm/NA
–155 dBm/NA
–153 dBm/NA
–152 dBm/NA
–151 dBm/NA
–143 dBm/–150 dBm
–144 dBm/–152 dBm
–147 dBm/–154 dBm
–147 dBm/–153 dBm
–143 dBm/–150 dBm
–145 dBm/–151 dBm
–141 dBm/–149 dBm
–139 dBm/–146 dBm
–138 dBm/–146 dBm
–134 dBm/–141 dBm
–132 dBm/–140 dBm
–130 dBm/–140 dBm
–130 dBm/–138 dBm
–128 dBm/–138 dBm
–100 dBm/NA nominal
–152 dBm/NA typical
–156 dBm/NA typical
–158 dBm/NA typical
–157 dBm/NA typical
–155 dBm/NA typical
–154 dBm/NA typical
–153 dBm/NA typical
–153 dBm/NA typical
–147 dBm/–154 dBm typical
–148 dBm/–155 dBm typical
–149 dBm/–156 dBm typical
–149 dBm/–152 dBm typical
–146 dBm/–153 dBm typical
–148 dBm/–152 dBm typical
–146 dBm/–150 dBm typical
–142 dBm/–149 dBm typical
–139 dBm/–147 dBm typical
–138 dBm/–145 dBm typical
–135 dBm/–145 dBm typical
–135 dBm/–142 dBm typical
–133 dBm/–142 dBm typical
100 to 200 kHz
200 to 500 kHz
500 kHz to 1 MHz
1 to 10 MHz
10 MHz to 2.1 GHz
2.1 to 3.6 GHz
–157 dBm/NA
–160 dBm/NA
–162 dBm/NA
–164 dBm/NA
–164 dBm/NA
–163 dBm/NA
–160 dBm/NA typical
–163 dBm/NA typical
–165 dBm/NA typical
–167 dBm/NA typical
–166 dBm/NA typical
–164 dBm/NA typical
Option P08, P13, P26, P43, P44, P50 3
Option P13, P26, P43, P44, P50 3
Option P26, P43, P44, P50 3
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17 GHz
17 to 20 GHz
20 to 26.5 GHz
–161 dBm/NA
–161 dBm/NA
–161 dBm/NA
–160 dBm/NA
–158 dBm/NA
–163 dBm/NA typical
–163 dBm/NA typical
–163 dBm/NA typical
–163 dBm/NA typical
–161 dBm/NA typical
Option P43, P44, P50 3
26.4 to 30 GHz
30 to 34 GHz
33.9 to 37 GHz
37 to 40 GHz
40 to 43 GHz
–157 dBm/NA
–155 dBm/NA
–153 dBm/NA
–152 dBm/NA
–149 dBm/NA
–159 dBm/NA typical
–158 dBm/NA typical
–157 dBm/NA typical
–156 dBm/NA typical
–154 dBm/NA typical
Option P44, P50 3
43 to 44 GHz
–149 dBm/NA
–154 dBm/NA typical
Option P50 3
44 to 46 GHz
46 to 50 GHz
–149 dBm/NA
–146 dBm/NA
–154 dBm/NA typical
–150 dBm/NA typical
Preamp off
Preamp on
Option P03, P08, P13, P26, P43, P44, P50 3
1. With the NFE (Noise Floor Extension) “Off”.
2. LNP (Low Noise Path) requires option LNP.
3. At higher frequency bands (beyond 3.6 GHz), Preamp “On” supersedes “LNP enabled”. LNP cannot operate simultaneously with preamp.
11 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
DANL with Noise Floor Extension (NFE) on
Improvement @ 95th percentile
Millimeter-Wave
(Option 543, 544, 550)
Band 0, f > 20 MHz
Band 1
Band 2
Band 3
Band 4
Band 5
Band 6
Example of effective DANL
Frequency 20 to 30 °C
Preamp Off
Preamp On
LNP enabled 1, 2
Mid-Band 0 (1.8 GHz)
Mid-Band 1 (5.95 GHz)
Mid-Band 2 (10.95 GHz)
Mid-Band 3 (15.3 GHz)
Mid-Band 4 (21.75 GHz)
Mid-Band 5 (30.4 GHz)
Mid-Band 6 (42.7 GHz)
–160 dBm
–154 dBm
–155 dBm
–154 dBm
–152 dBm
–148 dBm
–143 dBm
–172 dBm
–164 dBm
–167 dBm
–167 dBm
–165 dBm
–160 dBm
–156 dBm
N/A
–157 dBm
–157 dBm
–157 dBm
–157 dBm
–157 dBm
–150 dBm
Preamp Off
Preamp On
LNP enabled 1, 2
10 dB
9 dB
9 dB
9 dB
10 dB
11 dB
11 dB
9 dB
9 dB
8 dB
8 dB
9 dB
9 dB
8 dB
N/A
10 dB
9 dB
10 dB
11 dB
12 dB
11 dB
1. LNP (Low Noise Path) requires option LNP.
2. At higher frequency bands (beyond 3.6 GHz), Preamp “On” supersedes “LNP enabled”. LNP cannot operate simultaneously with preamp.
12 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Residues, images, and spurious responses
Residual responses
(Input terminated and 0 dB
attenuation)
Image responses
(Mixer level at –10 dBm)
(Mixer level at –30 dBm)
Other spurious responses
Carrier frequency ≤ 26.5 GHz
First RF order
(f ≥ 10 MHz from carrier)
Higher RF order
(f ≥ 10 MHz from carrier)
Carrier frequency > 26.5 GHz
First RF order
(f ≥ 10 MHz from carrier)
Higher RF order
(f ≥ 10 MHz from carrier)
LO-related spurious responses
(200 Hz ≤ f < 10 MHz from carrier),
Mixer level at –10 dBm
Line-related spurious responses
Second harmonic distortion (SHI)
RF/MW
(Option 503, 508, 513, 526)
Preamp on
(Option P03, P08, P13, P26)
Millimeter-Wave
(Option 543, 544, 550)
200 kHz to 8.4 GHz
Zero span or FFT or other frequencies
Tuned Freq (f)
10 MHz to 26.5 GHz
10 MHz to 3.6 GHz
10 MHz to 3.6 GHz
3.5 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 22 GHz
22 to 26.5 GHz
26.5 to 34.5 GHz
34.4 to 44 GHz
44 to 50 GHz
Mixer level
–100 dBm
–100 dBm nominal
Excitation Freq
f+45 MHz
f+10,245 MHz
f+645 MHz
f+645 MHz
f+645 MHz
f+645 MHz
f+645 MHz
f+645 MHz
f+645 MHz
f+645 MHz
Response
–80 dBc –118 dBc typical
–80 dBc –112 dBc typical
–80 dBc –101 dBc typical
–78 dBc –87 dBc typical
–74 dBc –84 dBc typical
–70 dBc –82 dBc typical
–68 dBc –79 dBc typical
–68 dBc –84 dBc typical
–57 dBc –79 dBc typical
–75 dBc nominal
Response
–10 dBm
–80 dBc + 20log(N 1) Including IF feedthrough, LO harmonic mixing responses
–40 dBm
–80 dBc + 20log(N 1) Including higher order mixer responses
–30 dBm
–90 dBc nominal
–30 dBm
–90 dBc nominal
–68 dBc 2 + 20log(N 1)
–73 dBc 2 + 20log(N 1) (nominal)
10 to 100MHz
100 M to 1.8 GHz
1.8 to 2.5 GHz
2.5 to 3 GHz
3 to 5 GHz
5 to 6.5 GHz
6.5 to 10 GHz
10 to 13.25 GHz
13.25 to 25 GHz
Mixer level
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
Preamp level
–45 dBm
–50 dBm
Mixer level
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
–15 dBm
Distortion 3
–57 dBc/NA
–60 dBc/NA
–77 dBc/–95 dBc
–77 dBc/–101 dBc
–77 dBc/–105 dBc
–70 dBc/–105 dBc
–62 dBc/–105 dBc
Distortion
–78 dBc nominal
–60 dBc nominal
Distortion 3
–57 dBc/NA
–60 dBc/NA
–72 dBc/–95 dBc
–72 dBc/–99 dBc
–77 dBc/–99 dBc
–77 dBc/–105 dBc
–70 dBc/–105 dBc
–62 dBc/–105 dBc
–65 dBc/–105 dBc (nom.)
SHI 3
+42 dBm/NA
+45 dBm/NA
+62 dBm/+80 dBm
+62 dBm/+86 dBm
+62 dBm/+90 dBm
+55 dBm/+90 dBm
+47 dBm/+90 dBm
SHI
+33 dBm nominal
+10 dBm nominal
SHI 3
+42 dBm/NA
+45 dBm/NA
+57 dBm/+80 dBm
+57 dBm/+84 dBm
+62 dBm/+84 dBm
+62 dBm/+90 dBm
+55 dBm/+90 dBm
+47 dBm/+90 dBm
+50 dBm/+90 dBm (nom.)
10 MHz to 1.8 GHz
1.8 to 13.25 GHz
13.25 to 25 GHz
Preamp level
–45 dBm
–50 dBm
–50 dBm
Distortion
–78 dBc (nominal)
–60 dBm (nominal)
–50 dBm (nominal)
SHI
+33 dBm (nominal)
+10 dBm (nominal)
0 dBm (nominal)
Source frequency
10 to 100 MHz
0.1 to 1.8 GHz
1.75 to 2.5 GHz
2.5 to 4 GHz
4 to 6.5 GHz
6.5 to 10 GHz
10 to 13.25 GHz
10 MHz to 1.8 GHz
1.8 to 13.25 GHz
Preamp on (Option P03, P08, P13,
P26, P43, P44, P50)
1. N is the LO multiplication factor. Refer to page 4 for the N value verses frequency ranges.
2. Nominally –40 dBc under large magnetic (0.38 Gauss rms) or vibrational (0.21 g rms) environmental stimuli.
3. Normal path/LNP enabled (requires Option LNP).
13 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Third-order intermodulation distortion (TOI)
(two –16 dBm tones at input mixer with tone separation > 5 times IF prefilter bandwidth, 20 to 30 °C)
For all frequency options
(Option 503, 508, 513, 526, 543,
544, and 550)
10 to 150 MHz
150 to 600 MHz
0.6 to 1.1 GHz
1.1 to 3.6 GHz
+13 dBm
+18 dBm
+20 dBm
+21 dBm
+16 dBm typical
+21 dBm typical
+22 dBm typical
+23 dBm typical
For RF/MW only
(Option 503, 508, 513, and 526)
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 26.5 GHz
+17 dBm
+17 dBm
+15 dBm
+16 dBm
+23 dBm typical
+23 dBm typical
+20 dBm typical
+22 dBm typical
For Millimeter-Wave only
(Option 543, 544, and 550)
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 26.5 GHz
26.5 to 50 GHz
+16 dBm
+16 dBm
+13 dBm
+13 dBm
+23 dBm typical
+23 dBm typical
+17 dBm typical
+20 dBm typical
+13 dBm nominal
Preamp on
(Option P03, P08, P13, P26, P43,
P44, and P50)
Tones at preamp input
(two –45 dBm)
(two –45 dBm)
(two –50 dBm)
10 to 500 MHz
500 MHz to 3.6 GHz
3.6 to 26.5 GHz
+4 dBm nominal
+4.5 dBm nominal
–15 dBm nominal
Figure 1. Nominal TOI performance versus frequency and tone separation
14 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Nominal Dynamic Range at 13 GHz
DANL and distortion relative mixer level (dB)
DANL and distortion relative mixer level (dB)
Nominal Dynamic Range at 1 GHz
-60
-70
-80
-90
-100
-110
-120
-130
-80
-70
-60
-50
-40
-30
-20
-60
-70
-80
-90
-100
-110
-120
-130
-80
-10
-70
Mixer Level (dBm)
-70
-80
-90
-100
-110
-120
-130
-60
-50
-40
-30
Mixer Level (dBm)
Figure 2a. Third-order dynamic range plots
-40
-30
-20
-10
Nominal Dynamic Range at 50 GHz
DANL and distortion relative mixer level (dB)
DANL and distortion relative mixer level (dB)
Nominal Dynamic Range at 26.5 GHz
-70
-50
Mixer Level (dBm)
-60
-80
-60
-20
-10
-60
-70
-80
-90
-100
-110
-120
-130
-80
-70
-60
-50
-40
-30
-20
-10
Mixer Level (dBm)
Figure 2b. Third-order dynamic range plots
––– DANL (30 kHz RBW)
––– DANL (1 Hz RBW)
– – 2nd Harmonic Distortion
––– 3rd Order Intermodulation
15 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Offset
Specification
Typical
Noise sidebands
(20 to 30 °C, CF = 1 GHz)
10 Hz
100 Hz
1 kHz
10 kHz
30 kHz
100 kHz
1 MHz
10 MHz
–94 dBc/Hz
–121 dBc/Hz
–129 dBc/Hz
–130 dBc/Hz
–129 dBc/Hz
–145 dBc/Hz
–155 dBc/Hz
–80 dBc/Hz nominal
–100 dBc/Hz typical
–125 dBc/Hz typical
–132 dBc/Hz typical
–132 dBc/Hz typical
–131 dBc/Hz typical
–146 dBc/Hz typical
–158 dBc/Hz typical
SSB Phase Noise (dBc/Hz)
Phase noise
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
Nominal Phase Noise at Different Center Frequencies
with RBW Selectivity Curves, Optimized Phase Noise, Versus Offset Frequency
RBW=100 Hz
RBW=1 kHz
RBW=10 kHz
RBW=100 kHz
CF=25.2 GHz
CF=50 GHz
CF=1 GHz
CF=10.2 GHz
0.1
1
10
100
1000
10000
Frequency (kHz)
Figure 3. Nominal PXA phase noise at various center frequencies
Option MPB, microwave preselector bypass 1
Frequency range
N9030A-508
N9030A-513
N9030A-526
N9030A-543
N9030A-544
N9030A-550
1.
3.6 to 8.4 GHz
3.6 to 13.6 GHz
3.6 to 26.5 GHz
3.6 to 43 GHz
3.6 to 44 GHz
3.6 to 50 GHz
When Option MPB is installed and enabled, some aspects of the analyzer performance change. Please refer to the PXA specification guide for
more details.
16 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
PowerSuite Measurement Specifications
Channel power
Amplitude accuracy, W-CDMA or IS95
(20 to 30 °C, attenuation = 10 dB)
± 0.61 dB (± 0.19 dB 95th percentile)
Occupied bandwidth
Frequency accuracy
± [span/1000] nominal
Adjacent channel power
Accuracy, 3GPP W-CDMA (ACLR)
(at specific mixer levels and ACLR ranges)
Adjacent
Alternate
± 0.09 dB
± 0.18 dB
± 0.16 dB
± 0.31 dB
Dynamic range (typical)
Without noise correction
With noise correction
–81.5 dB
–82.5 dB
–87 dB
–88 dB
Offset channel pairs measured
1 to 6
MS (UE)
BTS
Multi-carrier ACP
Accuracy, 3GPP W-CDMA (ACPR)
(4 carriers, 5 MHz offset, BTS, UUT ACPR
range at –42 to –48 dB, optimal mixer level
at –21 dBm)
± 0.13 dB
Multiple number of carriers measured
Up to 12
Power statistics CCDF
Histogram resolution
0.01 dB
Harmonic distortion
Maximum harmonic number
10th
Result
Fundamental power (dBm), relative harmonics power (dBc), total harmonic distortion in %
Intermod (TOI)
Measure the third-order products and intercepts from two tones
Burst power
Methods
Power above threshold, power within burst width
Results
Single burst output power, average output power, maximum power, minimum power within
burst, burst width
Spurious emission
3GPP W-CDMA table-driven spurious signals; search across regions
Dynamic range (1 to 3.6 GHz)
Absolute sensitivity (1 to 3.6 GHz)
97.1 dB
–86.4 dBm
(101.9 dB typical)
(–90.4 dBm typical)
cdma2000 ® (750 kHz offset)
Relative dynamic range
Absolute sensitivity
Relative accuracy
81.6 dB
–101.7 dBm
± 0.08 dB
(86.4 dB typical)
(–105.7 dBm typical)
3GPP W-CDMA (2.515 MHz offset)
Relative dynamic range
Absolute sensitivity
Relative accuracy
85.4 dB
–101.7 dBm
± 0.08 dB
(89.8 dB typical)
(–105.7 dBm typical)
Spectrum emission mask (SEM)
17 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
General Specifications
Temperature range
Operating
Storage
0 to 55 °C
–40 to +70 °C
Altitude
4,500 meters (approx 15,000 feet)
EMC
Complies with European EMC Directive 2004/108/EC
– IEC/EN 61326-1 or IEC/EN 61326-2-1
– CISPR Pub 11 Group 1, class A 1
– AS/NZS CISPR 11:2002
– ICES/NMB-001
This ISM device complies with Canadian ICES-001
Cet appareil ISM est conforme à la norme NMB-001 du Canada
Safety
Complies with European Low Voltage Directive 2006/95/EC
– IEC/EN 61010-1 3rd Edition
– Canada: CSA C22.2 No. 61010-1-12
– USA: UL 61010-1 3rd Edition
Acoustic statement (European Machinery Directive 2002/42/EC, 1.7.4.2u)
Acoustic noise emission
LpA < 70 dB
Operator position
Normal position
Per ISO 7779
Acoustic noise - more information
(Values given are per ISO 7779 standard in the “Operator Sitting” position)
Ambient temperature
< 40 °C
≥ 40 °C
Nominally under 55 dBA Sound Pressure. 55 dBA is generally considered suitable for use in
quiet office environment
Nominally under 65 dBA Sound Pressure. 65 dBA is generally considered suitable for use in
noisy office environment
Environmental stress
Samples of this product have been type tested in accordance with the Keysight Environmental Test Manual and verified to be robust
against the environmental stresses of storage, transportation, and end-use; those stresses include, but are not limited to, temperature, humidity, shock, vibration, altitude, and power line conditions; test methods are aligned with IEC 60068-2 and levels are similar to
MILPRF-28800F Class 3.
Power requirements
Voltage and frequency
Power consumption
On
Stanby
1.
100 to 120 V, 50/60/400 Hz
220 to 240 V, 50/60 Hz
630 W (Maximum)
40 W
The N9030A is in full compliance with CISPR 11, Class A emissions and is declared as such. In addition, the N9030A has been type tested and
shown to meet CISPR 11, Class B emissions limits. Information regarding the Class B emission performance of the N9030A is provided as a
convenience to the user and is not intended to be a regulatory declaration.
18 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Display
Resolution
Size
1024 x 768, XGA
213 mm (8.4 in.) diagonal (nominal)
Data storage
Internal
Removable solid state drive (80 GB)
External
Supports USB 2.0 compatible memory devices
Weight (without options)
Net
Shipping
22 kg (48 lbs) nominal
34 kg (75 lbs) nominal
Dimensions
Height
Width
Length
177 mm (7.0 in)
426 mm (16.8 in)
556 mm (21.9 in)
Warranty
The PXA signal analyzer is supplied with a 3-year standard warranty
Calibration cycle
The recommended calibration cycle is one year. Calibration services are available through Keysight service centers
Inputs and Outputs
Front panel
RF input Connector
Standard (Option 503, 508, 513, 526)
Option C35 (with Option 526 only)
Standard (Option 543, 544, 550)
Analog baseband IQ inputs (Option BBA) 1
Connectors (I, Q, I-Bar, Q-Bar, and Cal Out)
Cal Out
Signal
Frequency
Input impedance (4 connectors: I, Q, I-, Q-)
Probes supported 2
Active probe
Passive probe
Input return loss
50 Ω impedance only selected
Probe power
Voltage/current
USB 2.0 ports
Master (2 ports)
Standard
Connector
Output current
Headphone jack
Type-N female, 50 Ω nominal
APC 3.5 mm male, 50 Ω nominal
2.4 mm male, 50 Ω nominal
BNC female
AC coupled square wave
Selectable between 1 kHz and 250 kHz
50 Ω, 1 MΩ (selectable, nominal)
1130A, 1131A, 1132A, 1134A
1161A
–5 dB (0 to 10 MHz, nominal)
–0 dB (10 to 40 MHz. nominal)
+15 Vdc, ± 7% at 150 mA max nominal
–12.6 Vdc, ± 10% at 150 mA max nominal
Compatible with USB 2.0
USB Type-A female
0.5 A nominal
Miniature stereo audio jack (3.5 mm, also known as “1/8 inch”)
1. For additional specifications, please refer to Chapter BAA in the PXA Signal Analyzer specification guide
2. For more details, please refer to the Keysight Probe Configuration Guides, literature numbers 5968-7141EN and 5989-6162EN; probe heads
are necessary to attach to your device properly and probe connectivity kits such as E2668B, E2669A. or E2675A are required.
19 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
External mixing, Option EXM
Connection port
Connector
Impedance
Functions
Mixer bias range
IF input center frequency
Narrowband IF path
40 MHz BW IF path
85 or 160 MHz BW IF path
LO output frequency range
Rear panel
10 MHz out
Connector
Output amplitude
Frequency
Ext Ref In
Connector
Input amplitude range
Input frequency
Frequency lock range
Trigger 1 and 2 inputs
Connector
Impedance
Trigger level range
Trigger 1 and 2 outputs
Connector
Impedance
Level
Sync (reserved for future use)
Connector
Monitor output
Connector
Format
Resolution
Noise source drive +28 V (pulsed)
Connector
Output voltage
SMA, female
50 Ω nominal
Triplexed for mixer bias, IF input and LO output
± 10 mA in 10 uA step
322.5 MHz
250.0 MHz
300 MHz
3.75 to 14.0 GHz
BNC female, 50 Ω nominal
≥ 0 dBm nominal
10 MHz + (10 MHz x frequency reference accuracy)
BNC female, 50 Ω nominal
–5 to 10 dBm nominal
1 to 50 MHz nominal (selectable to 1 Hz resolution)
± 2 x 10–6 of specified external reference input frequency
BNC female
> 10 kΩ nominal
–5 to +5 V (TTL) factory preset
BNC female
50 Ω nominal
0 to 5 V (CMOS) nominal
BNC female
VGA compatible, 15-pin mini D-SUB
XGA (60 Hz vertical sync rates, non-interlaced) Analog RGB
1024 x 768
SNS series noise source
BNC female
On 28.0 ± 0.1 V (60 mA maximum)
Off < 1 V
For use with the Keysight SNS Series noise sources
Digital bus
Connector
MDR-80
20 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Rear panel
Analog out
Connector
USB 2.0 ports
Master (4 ports)
Standard
Connector
Output current
Slave (1 port)
Standard
Connector
Output current
BNC female
Compatible with USB 2.0
USB Type-A female
0.5 A nominal
Compatible with USB 2.0
USB Type-B female
0.5 A nominal
GPIB interface
Connector
GPIB codes
GPIB mode
IEEE-488 bus connector
SH1, AH1, T6, SR1, RL1, PP0, DC1, C1, C2, C3, C28, DT1, L4, C0
Controller or device
LAN TCP/IP interface
Standard
Connector
1000Base-T
RJ45 Ethertwist
IF output
Connector
Impedance
SMA female, shared by Opts CR3, CRP, and ALV
50 Ω nominal
2nd IF output, Option CR3
Center frequency
SA mode or I/Q analyzer with IF BW ≤ 25 MHz
with Option B40
with Option B85/B1X
322.5 MHz
250 MHz
300 MHz
Conversion gain
–1 to +4 dB (nominal) plus RF frequency response
Bandwidth
Low band
High band, with preselector
High band, with preselector bypassed 1
Up to 160 MHz (nominal)
Depends on center frequency
Up to 700 MHz (nominal); expandable to 900 MHz with corrections
Arbitrary IF output, Option CRP
Center frequency
Range
Resolution
10 to 75 MHz (user selectable)
0.5 MHz
Conversion gain
–1 to +4 dB (nominal) plus RF frequency response
Bandwidth
Output at 70 MHz
Low band or high band with preselector bypassed
Preselected band
100 MHz (nominal)
Depends on RF center frequency
Lower output frequencies
Subject to folding
Residual output signals
≤ –88 dBm (nominal)
1.
The maximum bandwidth is not centered around the IF output center frequency.
21 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Other Optional Output
Option ALV Log video out
General port specifications
Connector
Impedance
SMA female
Shared with other options
50 Ω nominal
Fast log video output
Output voltage
Maximum
Slope
Open-circuit voltages shown
1.6 V at –10 dBm nominal
25 ± 1 mV/dB nominal
Log fidelity
Range
Accuracy within range
49 dB (nominal) with input frequency at 1 GHz
± 1.0 dB nominal
Rise time
15 ns nominal
Fall time
Bands 1-4 with Option MPB
Other cases
40 ns nominal best case,
Depends on bandwidth
Option YAV Y-Axis output
General port specifications
Connector
Impedance
BNC female
Shared with other options
50 Ω nominal
Operating conditions
Display scale types
Log scales
Modes
Gating
Log or Lin
All (0.1 to 20 dB/div)
Spectrum analyzer only
Gating must be off
“Lin” is linear in voltage
Output scaling
Offset
Gain accuracy
0 to 1.0 V open circuit, representing bottom to top of screen
± 1% of full scale nominal
± 1% of output voltage nominal
Delay between RF input to analog output
71.7 µs +2.56/RBW + 0.159/VBW nominal
Screen video
Log video (Log envelope) output
Amplitude range (terminated with 50 Ω)
Maximum
1.0 V nominal for –10 dBm at the mixer
Scale factor
Bandwidth
Operating conditions
1 V per 192.66 dB
Set by RBW
Select Sweep Type = Swept
Linear video (AM Demod) output
Amplitude range (terminated with 50 Ω)
Maximum
Minimum
1.0 V nominal for signal envelope at the reference level
0V
Scale factor
If carrier level is set to half the reference level in volts, the scale factor is 200% of carrier
level per volt. Regardless of the carrier level, the scale factor is 100% of reference level per
volt.
Bandwidth
Operating conditions
Set by RBW
Select Sweep Type = Swept
22 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer
Frequency
Frequency span
Standard instrument
Option B25
Option B40
Option B85
Option B1X
10 Hz to 10 MHz
10 Hz to 25 MHz
10 Hz to 40 MHz
10 Hz to 85 MHz
10 Hz to 160 MHz
Resolution bandwidth (spectrum measurement)
Range
Overall
Span = 1 MHz
Span = 10 kHz
Span = 100 Hz
Window shapes
100 mHz to 3 MHz
50 Hz to 3 MHz
1 Hz to 10 kHz
100 mHz to 100 Hz
Flat Top, Uniform, Hanning, Hamming, Gaussian, Blackman, Blackman-Harris, Kaiser Bessel (K-B 70 dB, K-B 90 dB and K-B 110 dB)
Analysis bandwidth (waveform measurement)
Standard instrument
Option B25
Option B40
Option B85
Option B1X
10 Hz to 10 MHz
10 Hz to 25 MHz
10 Hz to 40 MHz
10 Hz to 85 MHz
10 Hz to 160 MHz
IF frequency response (standard 10 MHz IF path)
IF frequency response (demodulation and FFT response relative to the center frequency)
Analysis
BW (MHz)
Freq (GHz)
≤ 3.6
3.6 to 26.5
3.6 to 26.5
26.5 to 50
26.5 to 50
1.
≤ 10
≤ 10 preselected
≤ 10 preselector off 1
≤ 10 preselected
≤ 10 preselected off 1
Option MPB is installed and enabled.
Max error
Midwidth
error (95th
percentile)
Slope (dB/MHz)
(95th percentile) RMS (nominal)
± 0.20 dB
± 0.12 dB
± 0.10 dB
± 0.25 dB
± 0.12 dB
± 0.10 dB
± 0.30 dB
± 0.12 dB
± 0.10 dB
0.02 dB
0.23 dB
0.02 dB
0.12 dB
0.024 dB
23 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer (continued)
IF phase linearity
Center freq (GHz)
≥ 0.02, < 3.6
≥ 3.6 to ≤ 26.5
≥ 3.6
Span (MHz)
≤ 10
≤ 10
≤ 10
Preselector
Peak-to-peak
(nominal)
RMS (nominal)
NA
Off 1
On
0.06°
0.10°
0.11°
0.012°
0.022°
0.024°
Dynamic range (standard 10 MHz IF path)
Clipping-to-noise dynamic range
Clipping level at mixer
IF gain = Low
IF gain = High
Noise density at mixer at center
frequency
Excluding residuals and spurious
responses
Center frequency ≥ 20 MHz
–8 dBm nominal
–17.5 dBm nominal
–10 dBm
–20 dBm
(DANL + IF Gain effect) + 2.25 dB
Data acquisition (standard 10 MHz IF path)
Time record length
Analysis tool
IQ analyzer
Advanced tools
4,000,000 IQ sample Pairs
Data packing
32-bit
64-bit
Length (IQ sample pairs)
536 MSa (229 Sa)
268 MSa (228 Sa)
Length (time units)
Samples/Sample rate (IQ pair)
Sample rate
IQ pairs
ADC resolution
1.
Span x 1.25
16 bits
Option MPB is installed and enabled.
Waveform measurement
89600 VSA software or fast capture
2 GB total memory
24 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer (continued)
Option B25 25 MHz analysis bandwidth (Option B25 is automatically included in Option B40,
B85 or B1X)
IF frequency response (B25 IF path)
IF frequency response (demodulation and FFT response relative to the center frequency)
Freq (GHz)
Analysis BW (MHz)
< 3.6
10 to ≤ 25
3.6 to 26.5
10 to ≤ 25
preselected
3.6 to 26.5
10 to ≤ 25
preselector off 1
26.5 to 50
10 to ≤ 25
preselected
26.5 to 50
10 to ≤ 25
preselector off 1
Max error
Midwidth
error (95th
percentile)
Slope (dB/MHz)
(95th percentile) RMS (nominal)
± 0.30 dB
± 0.12 dB
± 0.05 dB
0.02 dB
0.50 dB
± 0.40 dB
0.03 dB
0.31 dB
± 0.40 dB
0.02 dB
IF phase linearity
Center freq (GHz)
Span (MHz)
≥ 0.02, < 3.6
≥ 3.6
≤ 25
≤ 25
Preselector
Peak-to-peak
(nominal)
RMS (nominal)
NA
Off 1
0.48°
0.85°
0.12°
0.20°
Dynamic range (B25 IF path)
Full scale (ADC clipping)
Default settings, signal at CF
(IF gain = Low)
Band 0
Bands 1 through 4
–8 dBm mixer level nominal
–7 dBm mixer level nominal
High gain setting, signal at CF
(IF gain = High)
Band 0
Bands 1 through 4
–18 dBm mixer level nominal, subject to gain limitations
–17 dBm mixer level nominal, subject to gain limitations
Effect of signal frequency ≠ CF
Up to ± 3 dB nominal
Data acquisition (B25 IF path)
Time record length
Analysis tool
IQ analyzer
Advanced tools
4,000,000 IQ sample Pairs
Data packing
32-bit
64-bit
Length (IQ sample pairs)
536 MSa (229 Sa)
268 MSa (228 Sa)
Length (time units)
Samples/Sample rate (IQ pair)
Sample rate
IQ pairs
ADC resolution
1.
Span x 1.25
16 bits
Option MPB is installed and enabled.
Waveform measurement
89600 VSA software or fast capture
2 GB total memory
25 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer (continued)
Option B40 40 MHz analysis bandwidth (Option B40 is automatically included in Option B85
or B1X)
IF frequency response (B40 IF path)
IF frequency response
Center freq. (GHz)
≥ 0.03, < 3.6
≥ 3.6, ≤ 8.4
> 8.4, ≤ 26.5
≥ 26.5, < 34.4
≥ 34.4, < 50
Relative to center frequency
Span (MHz)
Preselector
≤ 40
≤ 40
≤ 40
≤ 40
≤ 40
NA
Off 1
Off 1
Off 1
Off 1
± 0.4 dB
± 0.4 dB
± 0.7 dB
± 0.8 dB
± 1.0 dB
Typical
RMS (nominal)
± 0.25 dB
± 0.16 dB
± 0.20 dB
± 0.25 dB
± 0.35 dB
0.05 dB
0.05 dB
0.05 dB
0.1 dB
0.1 dB
IF phase linearity (deviation from mean phase linearity)
Center freq (GHz)
≥ 0.03, < 3.6
≥ 3.6
Span (MHz)
Preselector
Peak-to-peak
(nominal)
RMS (nominal)
≤ 40
≤ 40
NA
Off 1
0.16°
1.5°
0.041°
0.35°
EVM (EVM measurement floor for an 802.11g OFDM signal, using 89600B software equalization, channel estimation and data EQ)
2.4 GHz
5.8 GHz with Option MPB
–52.0 dB (0.25%) nominal
–49.1 dB (0.35%) nominal
Dynamic range (B40 IF path)
SFDR
(Spurious-free dynamic range)
Signal frequency within ± 12 MHz of center
–80 dBc nominal
Signal frequency anywhere within analysis BW
Spurious response within
± 18 MHz of center
–79 dBc nominal
Response anywhere within
analysis BW
–77 dBc nominal
Full scale (ADC clipping)
Default settings, signal at CF
(IF gain = Low: IF gain offset = 0 dB)
Band 0
Bands 1 through 4
High gain setting, signal at CF
(IF gain = High)
Band 0
Bands 1 through 4
Effect of signal frequency ≠ CF
1.
Option MPB is installed and enabled.
–8 dBm mixer level nominal
–7 dBm mixer level nominal
–18 dBm mixer level nominal, subject to gain
limitations
–17 dBm mixer level nominal, subject to gain
limitations
Up to ± 3 dB nominal
26 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer (continued)
Option B40 40 MHz analysis bandwidth
Data acquisition (B40 IF path)
Time record length
Analysis tool
IQ analyzer
Advanced tools
4,000,000 IQ sample pairs
Waveform measurement
Data packing
89600 VSA software or fast capture
32-bit
64-bit
Length (IQ sample pairs)
536 MSa (229 Sa)
268 MSa (228 Sa)
Length (time units)
Samples/Sample rate (IQ pair)
2 GB total memory
Sample rate
IQ pairs
ADC resolution
Span x 1.25
12 bits
Option B85 85 MHz or B1X 160 MHz analysis bandwidth
IF frequency response (B85 or B1X IF path)
IF frequency response
Center freq. (GHz)
Relative to center frequency
Span (MHz)
Preselector
Typical
RMS (nominal)
≥ 0.1, < 3.6
≤ 85
≤ 140
≤ 160
NA
NA
NA
± 0.6 dB
± 0.6 dB
± 0.17 dB
± 0.25 dB
± 0.2 dB (nom)
0.05 dB
0.05 dB
0.07 dB
≥ 3.6, ≤ 8.4
≤ 85
≤ 140
≤ 160
Off 1
Off 1
Off 1
± 0.73 dB
± 0.8 dB
± 0.2 dB
± 0.35 dB
± 0.3 dB (nom)
0.05 dB
0.05 dB
0.07 dB
> 8.4, ≤ 26.5
≤ 85
≤ 140
≤ 160
Off 1
Off 1
Off 1
± 1.10 dB
± 1.30 dB
± 0.50 dB
± 0.75 dB
± 0.5 dB (nom)
0.1 dB
0.1 dB
0.12 dB
≥ 26.5, ≤ 50
≤ 85
≤ 140
Off 1
Off 1
± 1.20 dB
± 1.40 dB
± 0.45 dB
± 0.65 dB
0.12 dB
0.12 dB
IF phase linearity (deviation from mean phase linearity)
Center freq (GHz)
≥ 0.03, < 3.6
≥ 3.6,
EVM (EVM measurement floor)
Span (MHz)
Preselector
Peak-to-peak
(nominal)
RMS (nominal)
≤ 140
≤ 160
≤ 140
≤ 160
NA
NA
Off 1
Off 1
0.9°
1.7°
1.6°
2.8°
0.20°
0.42°
0.39°
0.64°
Customized settings required, preselector bypassed (Option MPB) above Band 0
Case 1: 62.5 Msymbol/s, 16QAM signal, RRC filter alpha of 0.2, non-equalized, with approximately 75 MHz occupied bandwidth
Band 0, 1.8 GHz
Band 1, 5.95 GHz
0.8% nominal
1.1% nominal
Case 2: 104.167 Msymbol/s, 16QAM signal, RRC filter alpha of 0.35, non-equalized, with approximately 140 MHz occupied bandwidth
Band 1, 5.95 GHz
Band 2, 15.3 GHz
Band 4, 26 GHz
Effect of signal frequency ≠ CF
1.
Option MPB is installed and enabled.
3.0% nominal, (unequalized)
2.5% nominal, (unequalized)
3.5% nominal, (unequalized)
Up to ± 3 dB nominal
0.5% nominal, (equalized)
0.6% nominal, (equalized)
1.6% nominal, (equalized)
27 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
I/Q Analyzer (continued)
Option B85 85 MHz or B1X 160 MHz analysis bandwidth
Dynamic range (B85 or B1X IF path)
SFDR (Spurious-free dynamic range)
Signal frequency within ± 12 MHz of center
–75 dBc nominal
Signal frequency anywhere within analysis BW
Spurious response within ± 63 MHz
of center
Response anywhere within
analysis BW
Full scale (ADC clipping)
Default settings, signal at CF
(IF gain = Low: IF gain offset = 0 dB)
Band 0
Band 1 through 4
High gain setting, signal at CF
(IF gain = High)
Band 0
Band 1 through 4
Effect of signal frequency ≠ CF
–74 dBc nominal
–72 dBc nominal
–8 dBm mixer level nominal
–7 dBm mixer level nominal
–18 dBm mixer level nominal, subject to gain limitations
–17 dBm mixer level nominal, subject to gain limitations
Up to ± 3 dB nominal
Data acquisition (B85 or B1X IF path)
Time record length
Analysis tool
IQ analyzer
Advanced tools
Length (IQ sample pairs)
Length (time units)
Sample rate
IQ pairs
ADC resolution
4,000,000 IQ sample pairs
Data packing
32-bit
64-bit
536 MSa (229 Sa)
268 MSa (228 Sa)
Samples/Sample rate (IQ pair)
Waveform measurement
89600 VSA software or fast capture
2 GB total memory
Span x 1.25
14 bits
Real-time spectrum analyzer (RTSA) 1
Option RT1 or RT2
Real-time analysis
Real-time analysis bandwidth
Option RT1
Option RT2
Minimum detectable signal duration with
> 60 dB StM 2 ratio
Option RT1
Option RT2
Minimum signal duration with 100%
probability of intercept (POI) at full amplitude accuracy
Option RT1
Option RT2
Minimum acquisition time
FFT rate
Up to 160 MHz
Up to 160 MHz
Analysis BW option determines the max real-time bandwidth
Analysis BW option determines the max real-time bandwidth
11.42 ns
5.0 ns
For Frequency Mask Triggering (FMT)
17.3 μs
3.57 μs
100 μs
292,969/s
Signal is at mask level
Signal is at mask level
1. For additional RTSA specifications, please refer to Option RT1/RT2 Chapter in the PXA Signal Analyzer specifications guide
2. StM = “Signal-to-Mask”
28 | Keysight | N9030A PXA X-Series Signal Analyzer - Data Sheet
Related Literature
Keysight PXA signal analyzers
Brochure
5990-3951EN
Configuration guide
5990-3953EN
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
www.lxistandard.org
LAN eXtensions for Instruments puts the power of Ethernet and the
Web inside your test systems. Keysight is a founding member of the LXI
consortium.
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.
www.keysight.com/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
Austria
Belgium
Finland
France
Germany
Ireland
Israel
Italy
Luxembourg
Netherlands
Russia
Spain
Sweden
Switzerland
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
0800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
cdma2000® is a registered certification mark of the Telecommunications Industry
Association.
United Kingdom
www.keysight.com/find/N9030A
www.keysight.com/find/PXA
www.keysight.com/find/xseries_apps
For other unlisted countries:
www.keysight.com/find/contactus
(BP-07-10-14)
This information is subject to change without notice.
© Keysight Technologies, 2013 – 2015
Published in USA, February 13, 2015
5990-3952EN
www.keysight.com
Similar pages