Document 581-1 Shielded Power Inductors–LPS5030 Series • Very low DCR; excellent current handling • 4.9 × 4.9 mm footprint; less than 3 mm tall Designer’s Kit C420 contains 3 each of all values Core material Ferrite Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 226 – 244 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 750/7″reel; 2500/13″ reel Plastic tape: 12 mm wide, 0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm PCB washing Only pure water or alcohol recommended DCR SRF max3 typ4 ±20% (µH) (Ohms) (MHz) Inductance2 Part number1 LPS5030-901ML_ LPS5030-122ML_ LPS5030-172ML_ LPS5030-222ML_ LPS5030-332ML_ 0.90 1.2 1.7 2.2 3.3 Isat (A)5 10% 20% 30% drop drop drop Irms (A)6 20°C 40°C rise rise 0.040 0.043 0.051 0.057 0.066 250 210 190 168 125 3.8 3.5 3.0 2.9 2.3 4.0 3.6 3.2 3.1 2.5 4.1 3.7 3.3 3.2 2.6 2.10 2.00 1.90 1.60 1.40 2.80 2.65 2.50 2.15 1.80 LPS5030-472ML_ LPS5030-562ML_ LPS5030-682ML_ LPS5030-822ML_ LPS5030-103ML_ 4.7 5.6 6.8 8.2 10.0 0.083 0.089 0.099 0.125 0.127 84 70 56 45 30 1.9 1.8 1.6 1.6 1.4 2.0 1.8 1.7 1.7 1.4 2.0 1.9 1.7 1.7 1.4 1.30 1.25 1.20 1.10 1.00 1.75 1.65 1.60 1.55 1.50 LPS5030-123ML_ LPS5030-153ML_ LPS5030-183ML_ LPS5030-223ML_ LPS5030-333ML_ 12.0 15.0 18.0 22.0 33.0 0.155 0.160 0.170 0.190 0.260 24 32 27 24 19 1.3 0.80 0.80 0.70 0.60 1.4 0.90 0.82 0.75 0.63 1.4 0.90 0.87 0.78 0.64 0.95 0.92 0.90 0.88 0.85 1.40 1.40 1.30 1.25 1.20 LPS5030-473ML_ LPS5030-683ML_ LPS5030-823ML_ LPS5030-104ML_ LPS5030-124ML_ 47.0 68.0 82.0 100 120 0.330 0.440 0.470 0.600 0.800 16 12 11 10 9 0.50 0.40 0.38 0.27 0.26 0.53 0.43 0.40 0.31 0.29 0.55 0.44 0.40 0.32 0.30 0.75 0.65 0.60 0.55 0.45 1.00 0.900 0.830 0.750 0.660 LPS5030-154ML_ LPS5030-224ML_ LPS5030-334ML_ LPS5030-474ML_ LPS5030-564ML_ 150 220 330 470 560 0.860 1.35 1.80 2.80 3.20 7.5 6.0 5.0 4.0 3.6 0.22 0.21 0.155 0.117 0.110 0.25 0.235 0.155 0.134 0.130 0.263 0.245 0.200 0.146 0.140 0.42 0.36 0.32 0.28 0.23 0.570 0.500 0.420 0.370 0.320 LPS5030-684ML_ LPS5030-105ML_ LPS5030-155ML_ LPS5030-185ML_ LPS5030-225ML_ 680 1000 1500 1800 2200 3.80 5.10 7.60 10.0 11.0 3.0 2.5 2.0 1.8 1.6 0.100 0.100 0.068 0.069 0.063 0.120 0.110 0.080 0.081 0.074 0.126 0.110 0.089 0.086 0.080 0.20 0.18 0.15 0.13 0.10 0.290 0.250 0.210 0.170 0.150 LPS5030-335ML_ LPS5030-475ML_ 3300 4700 19.5 26.0 1.3 1.1 0.056 0.063 0.067 0.090 0.125 0.049 0.056 0.059 0.080 0.110 1. Please specify termination and packaging codes: LPS5030-105MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic tape (750 parts per full reel). B= Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D= 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP 4263B LCR meter or equivalent. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current at which the inductance drops the specified amount from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 581-1 Revised 10/06/08 Document 581-2 Shielded SMT Power Inductors – LPS5030 Series Typical L vs Frequency Typical L vs Current 10000 10000 3300 µH 3300 µH 1000 µH 330 µH 100 µH 100 33 µH 10 µH 10 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 330 µH 100 µH 100 33 µH 10 µH 10 3.3 µH 3.3 µH 1 1 0.01 1 0.1 10 0.01 1 0.1 Frequency (MHz) 10 Current (A) Typical Current Derating 0.189 ±0.003* 4,80 ±0,076 0.189 ±0.003* 4,80 ±0,076 100 XXX X 90 80 Winding direction 70 Dash number 60 Internal code Recommended Land Pattern 50 40 30 20 Isat Irms 10 0 -40 -20 0 0.114 ±0.004 2,9 ±0,1 25°C Percent of rated current 120 110 20 40 60 80 100 0.138 3,50 0.090 2,30 45° typ 120 140 Ambient temperature (°C) 0.134 3,40 0.060 1,50 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. Dimensions are in 0.060 1,50 0.134 3,40 0.197 5,00 inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 0.197 5,00 0.090 2,30 Document 581-2 Revised 10/06/08