AHF-10 SERIES AC/DC Power Module 10W FEATURES ►Fully Encapsulated Plastic Case for PCB Mounting ►Universal Input 85~264VAC, 47~440Hz ►Protection Class II as per IEC/EN 60536 ►I/O Isolation 3000VAC with Reinforced Insulation ►Operating Ambient Temp. Range -25℃ to +70℃ ►Overload/Voltage/Temp. and Short Circuit Protection ►Designed-in EMI Emission meets EN55011/22 Class B & FCC Level B ►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11 ►Eco Design, Compliant to Energy Star Specification and ErP Directive 2009/125/EC ►UL/cUL/IEC/EN 60950-1 Safety Approval ►UL/cUL/IEC/EN 60950-1 Safety Approval & CE Marking PRODUCT OVERVIEW The MINMAX AHF-10 series is a range of fully encapsulated AC/DC power supply modules. The product features EMI-filter to EN55022, class B and EMS compliance to EN 61000-4 standard. Universal input voltage 85-264VAC and International safety approvals qualifies these power modules for applications in products with worldwide markets.The AHF-10 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment. Model Selection Guide Model Number Output Voltage AHF-10S03 AHF-10S05 AHF-10S12 AHF-10S15 AHF-10S24 AHF-10D12 AHF-10D15 VDC 3.3 5 12 15 24 ±12 ±15 Output Current Max. mA 2000 2000 833 666 416 ±380 ±300 Input Current 115VAC, 60Hz @Max. Load mA(typ.) 137 199 191 191 190 172 169 Max. capacitive Load Efficiency (typ.) @Max. Load % 70 73 76 76 76 77 77 uF 3900 3300 2200 2200 1000 #1000 #1000 # For each output Input Specifications Parameter Input Voltage Range Input Frequency Range Input Voltage Range No-Load Power Consumption Model Min. 85 47 120 ------- All Models 115VAC 230VAC Inrush Current (Cold Start at 25℃) Typ. ------------- Max. 264 440 370 0.3 10 20 Unit VAC Hz VDC W A A Output Specifications Conditions Parameter Output Voltage Setting Accuracy Line Regulation Vin=Min. to Max. @Full Load Single Output Models Iout=Min. to Max. Dual Output Models 3.3 & 5.0VDC Output Models 0-20 MHz Bandwidth Other Output Models Load Regulation Ripple & Noise Minimum Load Over Voltage Protection Temperature Coefficient Overshoot Zener diode clamp Foldback, auto-recovery 105 (long term overload condition may cause damage) Hiccup mode, Automatic Recovery Current Limitation Short Circuit Protection E-mail:[email protected] 2016/03/24 REV:14 Min. --------------------- Tel:886-6-2923150 Page 1 of 3 Typ. ±1.0 ±0.5 ±0.5 ±2.5 1.5 0.8 10 120 ±0.01 --- Max. ±2.0 ±1.0 ±1.0 ±5.0 1.8 1.0 ----±0.02 5 Unit %Vnom. % % % %VPP of Vo %VPP of Vo %Inom. % of Vo %/℃ % Vout --- --- %Inom. AHF-10 SERIES AC/DC POWER MODULE 10W General Specifications Parameter I/O Isolation Voltage I/O Isolation Resistance Switching Frequency Hold-up Time MTBF (calculated) Protection Class II Safety Approvals Conditions Input to Output, 60 Seconds 500 VDC Min. 3000 100 ----- Typ. ----100 20 300,000 Max. --------- Unit VACrms MΩ KHz ms Hours MIL-HDBK-217F@25℃, Ground Benign According IEC/EN 60536 UL/cUL 60950-1 recognition (UL certificate), IEC/EN 60950-1 (CB-report) EMC Specifications Parameter Standards & Level Conduction and Radiation EN55011 ,EN55024 ESD Radiated immunity Fast transient Surge Conducted immunity PFMF Dips Interruptions EMI EMS Performance EN55011, EN55022, FCC part 15 Class B EN61000-4-2 air ± 8kV , Contact ± 4kV EN61000-4-3 10V/m EN61000-4-4 ±2kV EN61000-4-5 ±1kV EN61000-4-6 10Vrms EN61000-4-8 30A/m EN61000-4-11 30% 10ms EN61000-4-11 >95% 5000ms B A B B B A B C Environmental Specifications Parameter Operating Ambient Temperature Range (See Power Derating Curve) Storage Temperature Range Power Derating Over Temperature Protection Humidity (non condensing) Cooling Conditions Min. Max. Unit Natural Convection -25 +70 ℃ -40 +85 ℃ W/℃ 95 % rel. H 260 ℃ +50℃ to +70℃ Lead Temperature (1.5mm from case for 10Sec.) 0.375 at 90℃ (automatic recovery at 67℃) --Natural Convection --- Notes 1 2 3 4 5 All specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted. These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power supplies however they may not meet all listed specifications. We recommend to protect the converter by a slow blow fuse in the input supply line. Other input and output voltage may be available, please contact factory. Specifications are subject to change without notice E-mail:[email protected] 2016/03/24 REV:14 Tel:886-6-2923150 Page 2 of 3 AHF-10 SERIES AC/DC POWER MODULE 10W Package Specifications Mechanical Dimensions Pin Connections 6.0 [0.24] 10.16 [0.40] 10.16 [0.40] 19.2 [0.76] 0.7 [0.03] Pin Single Output AC(N) – AC Neutral 2 AC(L) – AC Line NC Common 5 +Vout NC: No Connection 5.0 [0.20] Bottom View -Vout 4 64.0 [2.52] 3 54.0 [2.13] 4 1.0 [ 0.04] 3 5 Dual Output 1 2 1 4.0 [0.16] ►All dimensions in mm 17.78 [0.70] 45.0 [1.77] ►Tolerance: ±0.5 ►Pin (inches) (±0.02) diameter 1.0 ±0.1 (0.04±0.004) Physical Characteristics Case Size : 64.0x45.0x19.2mm (2.52x1.77x0.76 Inches) Case Material : Plastic resin (flammability to UL 94V-0 rated) Pin Material : Copper Alloy with Gold Plate Over Nickel Subplate Weight : 92g Minmax Technology Co., Ltd. 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] 2016/03/24 REV:14 Page 3 of 3