MC10H104 Quad 2‐Input AND Gate Description The MC10H104 is a quad 2-input AND gate. One of the gates has both AND/NAND outputs available. This MECL 10H™ part is a functional/pinout duplication of the standard MECL 10K™ family part, with 100% improvement in propagation delay, and no increase in power− supply current. www.onsemi.com Features • Propagation Delay, 1.0 ns Typical • Power Dissipation 25 mW/Gate (same as MECL 10K) • Improved Noise Margin 150 mV (Over Operating Voltage and 16 20 1 1 Temperature Range) PDIP−16 P SUFFIX CASE 648−08 • Voltage Compensated • MECL 10K Compatible • These Devices are Pb-Free, Halogen Free and are RoHS Compliant PLLC−20 FN SUFFIX CASE 775−02 MARKING DIAGRAMS* 1 20 16 MC10H104P AWLYYWWG 10H104G AWLYYWW 1 A WL, L YY, Y WW, W G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION Device Package Shipping† MC10H104FNG PLCC−20 (Pb-Free) 46 Units/Tube MC10H104FNR2G PLCC−20 (Pb-Free) 500/Tape & Reel MC10H104PG PDIP-16 (Pb-Free) 25 Units/Tube †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2016 August, 2016 − Rev. 9 1 Publication Order Number: MC10H104/D MC10H104 4 2 5 6 3 7 10 VCC1 1 16 VCC2 Aout 2 15 Dout Bout 3 14 Cout Ain 4 13 Din Ain 5 12 Din Bin 6 11 Cin Bin 7 10 Cin VEE 8 9 Dout 14 11 12 9 15 13 VCC1 = Pin 1 VCC2 = Pin 16 VEE = Pin 8 Pin assignment is for Dual-in-Line Package. Figure 1. Logic Diagram Figure 2. Pin Assignment Table 1. MAXIMUM RATINGS Symbol Characteristic Rating Unit VEE Power Supply (VCC = 0) −8.0 to 0 Vdc VI Input Voltage (VCC = 0) 0 to VEE Vdc Iout Output Current Continuous Surge TA Operating Temperature Range Tstg Storage Temperature Range Plastic Ceramic mA 50 100 0 to +75 °C °C −55 to +150 −55 to +165 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 2. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 1) 0° Symbol 75° Min Max Min Max Min Max Unit Power Supply Current − 39 − 35 − 39 mA IinH Input Current High − 425 − 265 − 265 μA IinL Input Current Low 0.5 − 0.5 − 0.3 − μA VOH High Output Voltage −1.02 −0.84 −0.98 −0.81 −0.92 −0.735 Vdc VOL Low Output Voltage −1.95 −1.63 −1.95 −1.63 −1.95 −1.60 Vdc VIH High Input Voltage −1.17 −0.84 −1.13 −0.81 −1.07 −0.735 Vdc VIL Low Input Voltage −1.95 −1.48 −1.95 −1.48 −1.95 −1.45 Vdc IE Characteristic 25° 1. Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. Outputs are terminated through a 50 W resistor to −2.0 V. www.onsemi.com 2 MC10H104 Table 3. AC PARAMETERS 0° Symbol 25° 75° Min Max Min Max Min Max Unit Propagation Delay 0.4 1.6 0.45 1.75 0.45 1.9 ns tr Rise Time 0.5 1.6 0.5 1.7 0.5 1.8 ns tf Fall Time 0.5 1.6 0.5 1.7 0.5 1.8 ns tpd Characteristic NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. www.onsemi.com 3 MC10H104 PACKAGE DIMENSIONS 20 LEAD PLLC CASE 775−02 ISSUE F B 0.007 (0.180) Y BRK −N− M T L-M 0.007 (0.180) U M N S T L-M S G1 0.010 (0.250) S N S D −L− −M− Z W 20 D 1 X V S T L-M S N S VIEW D−D A 0.007 (0.180) M T L-M S N S R 0.007 (0.180) M T L-M S N S Z C H −T− VIEW S G1 0.010 (0.250) S T L-M SEATING PLANE F 0.007 (0.180) VIEW S S N T L-M S N S K 0.004 (0.100) J M K1 E G 0.007 (0.180) S NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. DIMENSIONS IN INCHES. 3. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM −T−, SEATING PLANE. 5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). www.onsemi.com 4 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.021 0.050 BSC 0.026 0.032 0.020 −−− 0.025 −−− 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 −−− 0.020 2_ 10 _ 0.310 0.330 0.040 −−− MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.53 1.27 BSC 0.66 0.81 0.51 −−− 0.64 −−− 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 −−− 0.50 2_ 10 _ 7.88 8.38 1.02 −−− M T L-M S N S MC10H104 PACKAGE DIMENSIONS PDIP−16 CASE 648−08 ISSUE V D A 16 9 E H E1 1 NOTE 8 b2 8 c B TOP VIEW END VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A e/2 NOTE 3 L A1 C D1 e SEATING PLANE M eB END VIEW 16X b SIDE VIEW 0.010 M C A M B M STYLE 1: PIN 1. CATHODE 2. CATHODE 3. CATHODE 4. CATHODE 5. CATHODE 6. CATHODE 7. CATHODE 8. CATHODE 9. ANODE 10. ANODE 11. ANODE 12. ANODE 13. ANODE 14. ANODE 15. ANODE 16. ANODE NOTE 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION eB IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX −−−− 0.210 0.015 −−−− 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.735 0.775 0.005 −−−− 0.300 0.325 0.240 0.280 0.100 BSC −−−− 0.430 0.115 0.150 −−−− 10 ° MILLIMETERS MIN MAX −−− 5.33 0.38 −−− 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 18.67 19.69 0.13 −−− 7.62 8.26 6.10 7.11 2.54 BSC −−− 10.92 2.92 3.81 −−− 10 ° STYLE 2: PIN 1. COMMON DRAIN 2. COMMON DRAIN 3. COMMON DRAIN 4. COMMON DRAIN 5. COMMON DRAIN 6. COMMON DRAIN 7. COMMON DRAIN 8. COMMON DRAIN 9. GATE 10. SOURCE 11. GATE 12. SOURCE 13. GATE 14. SOURCE 15. GATE 16. SOURCE MECL is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10H104/D