NES-100 100W Single Output Switching Power Supply series Features : Protections: Short circuit / Overload / Over voltage Cooling by free air convection LED indicator for power on 100% full load burn-in test 2 years warranty SPECIFICATION MODEL DC VOLTAGE OUTPUT NES-100-48 48V 13.6A 11.2A 8.5A 7A 4.5A 2.3A 0 ~ 11.2A 0 ~ 8.5A 0 ~ 7A 0 ~ 4.5A 0 ~ 2.3A RATED POWER 100W 102W 100.8W 102W 105W 108W 110.4W RIPPLE & NOISE (max.) Note.2 80mVp-p 120mVp-p 120mVp-p 120mVp-p 120mVp-p 120mVp-p 150mVp-p VOLTAGE ADJ. RANGE 7.13 ~ 8.3V 1.0% 8.55 ~ 9.9V 1.0% 11.4 ~ 13.2V 1.0% 14.25 ~ 16.5V 1.0% 22.8 ~ 26.4V 1.0% 45.6 ~ 52.8V 1.0% 4.75 ~ 5.5V 2.0% LINE REGULATION Note.4 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION Note.5 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 500ms, 20ms/230VAC 500ms, 20ms/115VAC at full load HOLD UP TIME (Typ.) 30ms/230VAC VOLTAGE RANGE 85 ~ 132VAC / 176 ~ 264VAC selected by switch FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 80% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2A/115VAC 1.2A/230VAC COLD START 36A OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 25ms/115VAC at full load 81% 248 ~ 373VDC 81% 83% 84% 86% 86% 27.6 ~ 32.4V 55.2 ~ 64.8V <2mA / 240VAC 110 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 5.75 ~ 6.75V 8.6 ~ 10.1V 10.4 ~ 12.2V 13.8 ~ 16.2V 17.25 ~ 20.25V Protection type : Hiccup mode, recovers automatically after fault condition is removed -20 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes UL60950-1, CB(IEC60950-1),CCC GB4943 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1, light industry level, criteria A EMS IMMUNITY MTBF DIMENSION PACKING NOTE NES-100-24 24V 0 ~ 13.6A OVERLOAD OTHERS NES-100-15 15V 20A PROTECTION (Note 6) NES-100-12 12V 0 ~ 20A LEAKAGE CURRENT EMC NES-100-9 9V CURRENT RANGE SETUP, RISE TIME SAFETY & NES-100-7.5 7.5V RATED CURRENT VOLTAGE TOLERANCE Note.3 INPUT NES-100-5 5V 320.7Khrs min. MIL-HDBK-217F (25 159*97*38mm (L*W*H) 0.55Kg; 30pcs/17.5Kg/0.97CUFT ) 1. All parameters not specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Line regulation is measured from low line to high line at rated load. 5. Load regulation is measured from 0% to 100% rated load. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) File Name:NES-100-SPEC 2010-10-18 NES-100 100W Single Output Switching Power Supply Mechanical Specification Case No. 901 series Unit:mm 3.5 7 152.5 1 3 84.5 8.2 4 5 6 2-M 97 65 9.5 2 3 7 +V ADJ. 3.5 4.5 159 22 M3 38 3.5 3- 3.5 9 150 9 6.5 28.5 Assignment DC OUTPUT -V DC OUTPUT +V 18 Pin No. 4,5 6,7 Assignment AC/L AC/N FG 18.5 Pin No. 1 2 3 78 24 Terminal Pin No. Assignment 117 Block Diagram fosc : 60KHz 220 110 RECTIFIERS & FILTER EMI FILTER I/P RECTIFIERS & FILTER POWER SWITCHING -V DETECTION CIRCUIT FG O.L.P. +V PWM CONTROL O.V.P. Derating Curve Static Characteristics Ta=25 100 100 Others 90 80 80 70 5V 50 LOAD (%) LOAD (%) 60 40 20 -20 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 85 100 115 176 120 200 125 220 130 240 132 264 INPUT VOLTAGE (VAC) 60Hz File Name:NES-100-SPEC 2010-10-18