Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to [email protected]. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FAN48611 2.5 MHz, Fixed-Output, Synchronous Tiny Boost® Regulator Features Description Input Voltage Range: 2.7 V to 4.8 V The FAN48611 is a low-power boost regulator designed to provide a minimum voltage regulated rail from a standard single-cell Li-Ion battery and advanced battery chemistries. Even below the minimum system battery voltage, the device maintains output voltage regulation. The combination of built-in power transistors, synchronous rectification, and low supply current suit the FAN48611 for battery-powered applications. Three External Components: 2012 1 H Inductor, 0402 Case Size Input / Output Capacitors Output Voltage: 5.25 V 350 mA Maximum Output Current Internal Synchronous Rectification True Load Disconnect Short-Circuit Protection 9-Bump, 1.215 mm x 1.215 mm, 0.4 mm Pitch, WLCSP The FAN48611 is available in a 9-bump, 0.4 mm pitch, Wafer-Level Chip-Scale Package (WLCSP). VIN FAN48611 10µF Applications VOUT 1µH (10µF x3) Class-D Audio Amplifier and USB OTG Supply SW PGND EN AGND Boost for Low-Voltage Li-Ion Batteries Smart Phones, Tablets, Portable Devices, and Wearables Figure 1. Typical Application Ordering Information Part Number VOUT FAN48611UC53X 5.25 V Operating Temperature Range -40°C to 85°C Package 9-Bump, 0.4 mm Pitch, WaferLevel Chip-Scale Package (WLCSP) Packing Method Device Marking Tape and Reel(1) KH Note: 1. Tape and reel specifications are available on www.onsemi.com. © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 www.fairchildsemi.com www.onsemi.com FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator June 2017 SW Q2A L1 Q2B VOUT VIN Q2 Q1 COUT CIN Synchronous Rectifier Control PGND MODULATOR LOGIC AND CONTROL EN Figure 2. Table 1. AGND IC Block Diagram Recommended Components Component Description Vendor Parameter L1 2012, 1.9 A, 0.6 mm Max. Height PIXC20120F1R0MDR CIN 20%, 6.3 V, X5R, 0402 COUT 20%, 6.3 V, X5R, 0402 Typ. Unit L 1 µH DCR (Series R) 175 m C1005X5R0J106M050BC TDK C 10 µF C1005X5R0J106M050BC TDK C 10 µF Pin Configuration VOUT A1 A2 SW B1 A3 A3 A2 A1 B3 B2 B1 C3 C2 C1 EN B2 PGND C1 VIN FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Block Diagram C2 B3 AGND C3 Figure 3. Top View Figure 4. Bottom View Pin Definitions Pin # Name Description A1, A2 VOUT A3 VIN Input Voltage. Connect to the Li-Ion battery input power source and the bias supply for the gate drivers. B1, B2 SW Switching Node. Connect to inductor. B3 EN Enable. When this pin is HIGH, the circuit is enabled. Connection to a logic voltage of 1.8 V and delivery voltage after UVLO typical voltage of 2.2 V is recommended. C1, C2 PGND Power Ground. This is the power return for the IC. COUT capacitor should be returned with the shortest path possible to these pins. C3 AGND Analog Ground. This is the signal ground reference for the IC. All voltage levels are measured with respect to this pin. Connect to PGND at a single point. Output Voltage. This pin is the output voltage terminal; connect directly to COUT. © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 2 www.fairchildsemi.com www.onsemi.com Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VIN Parameter Voltage on VIN Pin VOUT Voltage on VOUT Pin VSW Voltage on SW Node VCC Voltage on Other Pins ESD Electrostatic Discharge Protection Level Min. Max. Unit -0.3 6.0 V 6.0 V DC -0.3 6.0 Transient: 10 ns, 3 MHz -1.0 8.0 -0.3 6.0(2) Human Body Model, ANSI/ESDA/JEDEC JS-001-2012 2 Charged Device Model per JESD22-C101 2 V V kV TJ Junction Temperature -40 +150 °C TSTG Storage Temperature -65 +150 °C +260 °C TL Lead Soldering Temperature, 10 Seconds Note: 2. Lesser of 6.0 V or VIN + 0.3 V. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. ON Semiconductor does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Min. Max. Unit 4.8 V VIN Supply Voltage 2.7 IOUT Maximum Output Current 350 TA Ambient Temperature -40 +85 °C TJ Junction Temperature -40 +125 °C FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Absolute Maximum Ratings mA Thermal Properties Junction-to-ambient thermal resistance is a function of application and board layout. This data is measured with fourlayer 2s2p boards with vias in accordance to JEDEC standard JESD51. Special attention must be paid not to exceed junction temperature, TJ(max), at a given ambient temperature, TA. Symbol ϴJA Parameter Junction-to-Ambient Thermal Resistance © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 3 Typical Unit 50 °C/W www.fairchildsemi.com www.onsemi.com Recommended operating conditions, unless otherwise noted, circuit per Figure 1, VOUT= 5.25 V, VIN = 2.7 V to 4.8 V, and TA = -40˚C to 85˚C. Typical values are given VIN = 3.7 V and TA = 25˚C. Symbol Parameter Conditions Min. Typ. Max. Unit Power Supply VIN=3.7 V, IOUT=0, EN=VIN 90 140 IQ VIN Quiescent Current Shutdown: EN=0, VIN=3.7 V, VOUT=0 V 2.7 10.0 VUVLO Under-Voltage Lockout VIN Rising 2.2 2.3 VUVLO_HYS Under-Voltage Lockout Hysteresis 150 A V mV Inputs VIH Enable HIGH Voltage VIL Enable LOW Voltage IPD Current Sink Pull-Down EN Pin, Logic HIGH Low-State Active Pull-Down EN Pin, Logic LOW VREG Output Voltage Accuracy DC(3) Referred to VOUT ILK_OUT VIN-to-VOUT Leakage Current VOUT=0, EN=0, VIN=2.7 V ILK VOUT-to-VIN Reverse Leakage Current VOUT=5.3 V, EN=0, VIN=2.7 V VRIPPLE Output Ripple(4) 0 mA to 300 mA 30 VTRLOAD Load Transient(4) ILOAD=0 mA <--> 120 mA, tR=tF=1 µs ±30 ILOAD=0 mA <--> 285 mA, tR=tF=8 µs ±90 VTRLINE Line Transient(4) VIN=3.2 V <--> 3.9 V, ILOAD=120 mA tR=tF=7 µs ±50 VIN=3 V, ILOAD=5 mA 85 VIN=3 V, ILOAD=200 mA 90 VIN=3.6 V, ILOAD=200 mA 91 VIN=3.6 V, ILOAD=300 mA 92 RLOW 1.2 V 0.4 100 200 300 V nA 400 kΩ 4 % 1 A 3.5 A Outputs η Efficiency(4) -2 mV mV mV % FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Electrical Specifications Timing fSW Switching Frequency VIN=3.6 V, VOUT=5.25 V, ILOAD=300 mA tSS Soft-Start EN HIGH to Regulation (4) VIN=3.0 V, VOUT=5.25 V, ILOAD=0 mA, COUT=3 x 10 µF ISS Input Peak Current 90 tRST FAULT Restart Timer(4) 20 2.0 2.5 3.0 MHz s 1000 200 mA ms Power Stage RDS(ON)N N-Channel Boost Switch RDS(ON) VIN=3.6 V, VOUT=5.25 V 80 130 mΩ RDS(ON)P P-Channel Sync. Rectifier RDS(ON) VIN=3.6 V, VOUT=5.25 V 65 115 mΩ Boost Valley Current Limit VOUT=5.25 V 750 mA Boost Soft-Start Valley Current Limit VIN<VOUT < VOUT_TARGET 375 A T150T Over-Temperature Protection (OTP) 150 ˚C T150H OTP Hysteresis 20 ˚C IV_LIM IV_LIM_SS Notes: 3. DC ILOAD from 0 to 0.35 A. VOUT measured from mid-point of output voltage ripple. Effective capacitance of COUT > 6 F. 4. Guaranteed by design and characterization; not tested in production. © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 4 www.fairchildsemi.com www.onsemi.com Unless otherwise specified; VIN = 3.6 V, VOUT = 5.25 V, TA = 25°C, and circuit and components according to Figure 1. Figure 5. Quiescent Current vs. Input Voltage and Temperature Figure 6. Shutdown Current vs. Load Current and Temperature Figure 7. Efficiency vs. Load Current and Input Voltage Figure 8. Efficiency vs. Load Current and Temperature Figure 9. Output Regulation vs. Load Current and Input Voltage Figure 10. Output Regulation vs. Load Current and Temperature © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 5 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Typical Performance Characteristics www.fairchildsemi.com www.onsemi.com Unless otherwise specified; VIN = 3.6 V, VOUT = 5.25 V, TA = 25°C, and circuit and components according to Figure 1 Figure 11. Output Ripple vs. Load Current and Input Voltage Figure 12. Switching Frequency vs. Load Current and Temperature Figure 13. Startup, No Load Figure 14. Overload Protection Figure 15. Load Transient, 0 <-->120 mA, 1 µs Edge Figure 16. Load Transient, 0 <--> 285 mA, 8 µs Edge © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 6 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Typical Performance Characteristics www.fairchildsemi.com www.onsemi.com Unless otherwise specified; VIN=3.6 V, VOUT=5.25 V, TA=25°C, and circuit and components according to Figure 1 Figure 17. Line Transient, 3.2 <--> 3.9 VIN, 7 s Edge, 120 mA Load © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 7 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Typical Characteristics www.fairchildsemi.com www.onsemi.com FAN48611 is a synchronous boost regulator, typically operating at 2.5 MHz in Continuous Conduction Mode (CCM), which occurs at moderate to heavy load current and low VIN voltage. Table 2. In LIN2 Mode, the current source is equal to LIN1 current source Iss, typically 90 mA. If VOUT fails to reach VIN-300 mV after 1024 s, a fault condition is declared and the device waits 20 ms (tRST) to attempt an automatic restart. Operating Modes Mode Description Invoked When: LIN Linear Startup VIN > VOUT SS Boost Soft-Start VIN < VOUT < VOUT(TARGET) BST Boost Mode VOUT= VOUT(TARGET) Soft-Start (SS) Mode Upon the successful completion of LIN Mode (VOUT>VIN300 mV), the regulator begins switching with boost pulses current limited to 50% of nominal level. During SS Mode, if VOUT fails to reach regulation during the SS ramp sequence for more than 64 s, a fault is declared. If a large COUT is used, the reference is automatically stepped slower to avoid excessive input current draw. Boost Mode Regulation The current-mode modulator achieves excellent transient response and smooth transitions between CCM and DCM operation. During CCM operation, the device maintains a switching frequency of about 2.5 MHz. In light-load operation (DCM), frequency is naturally reduced to maintain high efficiency. Boost (BST) Mode This is a normal operating mode of the regulator. Fault State The regulator enters Fault State under any of the following conditions: Startup and Shutdown When EN is LOW, all bias circuits are off and the regulator enters Shutdown Mode. During shutdown, current flow is prevented from VIN to VOUT, as well as reverse flow from VOUT to VIN. It is recommended to keep load current draw below 50 mA until the device successfully executes startup. Table 3 describes the startup sequence. VOUT fails to achieve the voltage required to advance from LIN Mode to SS Mode. VOUT fails to achieve the voltage required to advance from SS Mode to BST Mode. Boost current limit triggers for 2 ms during BST Mode. Table 3. Boost Startup Sequence Start Mode VIN – VOUT > 300 mV; this fault can occur only after successful completion of the soft-start sequence. Entry LIN1 VIN > VUVLO, EN=1 LIN2 SS LIN1 Exit LIN1 or LIN2 Exit Exit End Timeout Mode (µs) VOUT > VIN300 mV SS TIMEOUT LIN2 VOUT > VIN300 mV SS TIMEOUT FAULT VOUT= VOUT(TARGET) BST VIN < VUVLO. Once a fault is triggered, the regulator stops switching and presents a high-impedance path between VIN and VOUT. After 20 ms, automatic restart is attempted. 512 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Functional Description Over-Temperature OVERLOAD FAULT TIMEOUT The regulator shuts down if the die temperature exceeds 150°C. Restart occurs when the IC has cooled by approximately 20°C. 1024 64 LIN Mode When EN is HIGH and VIN > VUVLO, the regulator attempts to bring VOUT within 300 mV of VIN using the internal fixed-current source from VIN (Q2). The current is limited to the Iss set point, which is typically 90 mA. The linear charging current is limited to a maximum of 200 mA to prevent any “brownout” situations where the system voltage drops too low. During LIN1 Mode, if VOUT reaches VIN-300 mV, SS Mode is initiated. Otherwise, LIN1 Mode expires after 512 s and LIN2 Mode is entered. © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 8 www.fairchildsemi.com www.onsemi.com soft-start, only to have the output capacitance discharged by the load when in Fault State. Output Capacitance (COUT) The effective capacitance (CEFF(5)) of small, high-value ceramic capacitors decreases as the bias voltage increases, as illustrated in Figure 18. Output Voltage Ripple Output voltage ripple is inversely proportional to C OUT. During tON, when the boost switch is on, all load current is supplied by COUT. VRIPPLE ( P P ) tON ILOAD COUT (1) and V tON t SW D t SW 1 IN V OUT therefore: V VRIPPLE ( P P ) tSW 1 IN V OUT t SW Figure 18. CEFF for 10 F, 0402, X5R, 6.3 V-Rated Capacitor (TDK C1005X5R0J106M050BC) Minimum CEFF Required for Stability Operating Conditions VOUT (V) VIN (V) ILOAD (mA) CEFF(MIN) (F) 5.25 2.7 to 4.8 0 to 350 6.0 ILOAD COUT 1 fSW (2) (3) (4) The maximum VRIPPLE occurs when VIN is minimum and ILOAD is maximum. For better ripple performance, more output capacitance can be added. FAN48611 is guaranteed for stable operation with the minimum value of CEFF (CEFF(MIN)) outlined in Table 4 Table 4. Layout Recommendations Note: 5. CEFF varies by manufacturer, capacitor material, and case size. The layout recommendations below highlight various top-copper pours by using different colors. To minimize spikes at VOUT, COUT must be placed as close as possible to PGND and VOUT, as shown below. For best thermal performance, maximize the pour area for all planes other than SW. The ground pour, especially, should fill all available PCB surface area and be tied to internal layers with a cluster of thermal vias. Inductor Selection FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Application Information Recommended nominal inductance value is 1 H. The FAN48611 employs valley-current limiting, so peak inductor current can reach 1.2 A for a short duration during overload conditions. Saturation causes the inductor current ripple to increase under high loading, as only the valley of the inductor current ripple is controlled. Startup Input current limiting is active during soft-start, which limits the current available to charge COUT and any additional capacitance on the VOUT line. If the output fails to achieve regulation within the limits described in the Soft-Start section above, a fault occurs, causing the circuit to shut down. It waits about 20 ms before attempting a restart. If the total combined output capacitance is very high, the circuit may not start on the first attempt, but eventually achieves regulation if no load is present. If a high current load and high capacitance are both present during soft-start, the circuit may fail to achieve regulation and continually attempt © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 9 www.fairchildsemi.com www.onsemi.com Layout Recommendation The table below pertains to the Package information on the following page. Table 5. Product-Specific Dimensions D E X Y 1.215 ±0.030 mm 1.215 ±0.030 mm 0.2075 mm 0.2075 mm © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 10 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Figure 19. www.fairchildsemi.com www.onsemi.com 0.03 C E 2X E A B 0.40 A1 BALL A1 INDEX AREA (Ø0.215) Cu Pad (Bottom) 0.40 D 0.03 C (Ø0.315) Solder Mask 2X RECOMMENDED LAND PATTERN (NSMD PAD TYPE) TOP VIEW 0.06 C 0.581±0.038 0.05 C 0.203±0.020 C SEATING PLANE D 0.40 0.40 0.378±0.018 SIDE VIEWS NOTES A. NO JEDEC REGISTRATION APPLIES. B. DIMENSIONS ARE IN MILLIMETERS. 0.005 C A B C. DIMENSIONS AND TOLERANCE PER Ø0.260±0.02 ASME Y14.5M, 2009. 9X D. DATUM C IS DEFINED BY THE C SPHERICAL CROWNS OF THE BALLS. B (Y) ±0.018 E. FOR DIMENSIONS D,E,X, AND Y SEE A PRODUCT DATASHEET. F. DRAWING FILNAME: MKT-UC009Ak rev2 1 2 3 E (X) ±0.018 FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator Physical Dimensions BOTTOM VIEW Figure 20. 9-Bump, 0.4 mm Pitch, Wafer-Level Chip-Scale Package (WLCSP) © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 11 www.fairchildsemi.com www.onsemi.com FAN48611 — 2.5 MHz, Fixed-Output Synchronous Tiny Boost® Regulator ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] © 2013 Semiconductor Components Industries, LLC. FAN48611 • Rev. 1.2 N. American Technical Support: 800-282-9855 Toll Free USA/Canada. Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.fairchildsemi.com www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] © Semiconductor Components Industries, LLC N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com