POWER CNS650-M Series 650 Watt AC-DC Power Supplies Data Sheet Total Power: 650 Watts Input Voltage: 90 - 264 V # of Outputs: Single SPECIAL FEATURES Designed for forced air and natural convection cooling Medical and ITE safety approvals, 2x MOPP Electrical Specifications PMBus™ interface Input Active current share with OR-ing FET Input voltage range 90 - 264 Vrms Frequency 47 - 63 Hz (360 - 440 Hz with higher leakage) Inrush current 50 Apk, cold start Leakage current <300 µA No load power < 500 mW Dual fused Type BF ready Active Power Factor Correction, 61000-3-2 compliant Built-in Class B EMI filter Less than 1U high 4” x 6” U-channel construction (open-frame or end-fan variants available for 12 V) <500 mW no-load power consumption Three-year warranty (consult factory for extended terms) SAFETY UL/CSA: ES60601-1/C22.2 No. 60601-1 UL 60950-1/C22.2 No. 60950-1 TÜV: EN 60601-1 DEMKO: EN 60950-1 CB: IEC 60950-1/IEC 60601-1 CCC: GB4943.1/GB9254; GB17625.1 CE: LVD, RoHS Output Maximum power 650 W, forced-air cooling (750 W peak) 400 W, free-air natural convection cooling (650 W peak) Adjustment range -0% / +15% Holdup time Fan output 20 ms @ 400 W 12 V @ 1.0 A (forced air) 12 V @ 0.5 A (natural convection) 5 V @ 2.0 A (forced air) 5 V @ 1.0 A (natural convection) Standby output CNS650-M Series Data Sheet Electrical Specifications (continued) Control and Protection Serial bus interface PMBus™ Current share Active Remote sense 2-wire (+ and -) Remote inhibit Pull inhibit low = main & fan output OFF (5 V standby is ON) Pull inhibit high (or floating) = all outputs ON AC OK Active high when normal AC input is present (with internal 10k ohm pull up to 3.3 Vdc) DC OK Active high when main O/P is within regulation (with internal 10k ohm pull up to 3.3 Vdc) Smart fan control Monitor, control and override Overvoltage protection Latching / AC recyle or inhibit toggle required for PSU restart Overload protection Auto-recovery (CC to 50% output) Overtemperature protection Auto-recovery with hysteresis Environmental Specifications Operating temperature -20 °C to +80 °C (derate at 50 °C), startup at -40 °C Storage temperature -40 °C to +85 °C Operating humidity 5% to 95% (non-condensing) Non-operating humidity 5% to 95% (non-condensing) Maximum altitude 5000 m (3000 m for medical), derating may apply Other Specifications Isolation 4000 Vac (input to output) 1500 Vac (input to PE; output to PE) Line harmonics 61000-3-2, Class A ESD immunity 61000-4-2; ±15kV (air)/±8kV (contact); Criterion A Conducted EMI Level B, CISPR 22 and FCC Part 15 Radiated EMI Level B, CISPR 22 and FCC Part 15 (with cover) Surge immunity 61000-4-5, Level 3 - Criterion A; Level 4 - Criterion C Medical EMC 60601-1-2, Edition 4 (cover maybe required for some tests) MTBF (Telcordia, Issue 3, Method 1, Case 3) > 950 KHrs, 25 °C, 410 W natural convection > 1.3 MHrs, 25 °C, 650 W forced air CNS650-M Series Data Sheet Ordering Information Model Number Output Voltage Vout Adjust Range (-0% /+15%) Minimum Load CNS653-ME5 12 V 12 - 13.8 V 0A CNS653-MF5 12 V 12 - 13.8 V 0A CNS653-MU 12 V 12 - 13.8 V 0A CNS655-MU 24 V 24 - 27.6 V 0A CNS658-MU 48 V 48 - 55.2 V 0A Max. Continuous Load (Free Air) Max. Peak Load (Free Air)1 Max. Continuous Load (Forced Air)2 Max. Peak Load (Forced Air)2 Regulation3 Ripple (p-p)4 NA NA 54.2 A 62.5 A ±2% 120 mV 30.0 A 54.2 A 54.2 A 62.5 A ±2% 120 mV 33.3 A 54.2 A 54.2 A 62.5 A ±2% 120 mV 16.7 A 27.1 A 27.1 A 31.3 A ±2% 240 mV 8.3 A 13.5 A 13.5 A 15.6 A ±2% 480 mV Peak load current not to exceed 10 seconds, Ta = 50 °C. 2 Requires at least 400 LFM of airflow. 3 At 25 °C including factory setpoint, line voltage and load current variations. 4 Peak-to-peak ripple measured at the output terminal with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with 0.1 µF capacitor across the output. 5 Optional Suffix “-ME” (end-fan) and “-MF: (open-frame) available on the 12 V output. 1 Input Connections (-MU and -MF Suffix) Pin Function TB1 PE TB2 L2/Neutral TB3 L1/Line Power Supply Side Output Connections System Side Dinkle EHK762V-03P Max Torque: 4kgf-cm Recommended Wire Size: AWG #22 to #14 Input Connections (-ME Suffix) Pin Function Power Supply Side System Side IEC Inlet Input AC IEC 60320 C14 (Male) IEC Cord C13 (Female) Pin Function BAR1 -Vout BAR2 -Vout BAR3 +Vout BAR4 +Vout Power Supply Side System Side Output Terminal Screw: M4X8 (4X) Max Torque: 10kgf-cm Molex 19099-0032 or 19141-0063 for AWG #16 to #14 Molex 19099-0048 or 19141-0083 for AWG #12 to #10 Other Output and Control Connections (Connector J304) Pin Designation Description 1 5VSB +5 V Standby Output J304 20-Pin Connector (PSU Side): 2 5VSB +5 V Standby Output Landwin: 2052P20008T or 3 5VSB_GND +5 V Standby Output Return/Ground CviLux: 4 SCL Serial Clock Signal (I2C) 5 A0 EEPROM Address Recommended Mating Connectors: 6 SDA Serial Data Signal (I2C) CviLux: 7 I_SHARE Active current share pin 8 SYS_GND Return Ground for signals and I2C 9 12VFAN 12 V Fan Output 10 REMOTE INHIBIT Output Inhibit Pin (Main Output) 11 FAN_RTN 12 V Fan Output Return/Ground 12 VIN_GOOD Input Line OK Signal 13 FAN_PWM1 FAN PWM 14 PWOK Output Power OK Signal 15 FAN_TACH1 Fan1 Tacho Signal 16 FAN_OVERRIDE External Fan Sensor for Override 17 FAN_FAIL Fain Fail Signal 18 FAN_FAULT_EN FAN Fault Enable Due to low RPM 19 REMOTE_SENSE+ Positive Remote Sense 20 REMOTE_SENSE- Remote Sense Return CI0120P1HD0-LF CI0120SD000 (housing) CI01TD21PE0 (contact pins) Landwin: 2050S2000 (housing) 2053T021V (contact pins) JST: PHDR-20VS (housing) SPHD-001T-P0.5 (contact pins) See ACCESSORIES Section CNS650-M Series Data Sheet Fan Output Connector for -MU, -MF Suffix (Connector J306) Pin Function Description 1 12VFAN 12 V fan output J306 4-Pin Connector (PSU Side): 2 FAN_RTN 12 V fan return CviLux: CI0104P1HK0-LF 3 FAN_PWM1 Fan PWM Landwin: 2003P0401V 4 FAN_TACH1 Fan1 tacho signal Recommended Mating Connectors: CviLux: CI0104S0000 (housing) CviLux: CI01T01MPP0 (contact pins) Landwin: 2001S0400 (housing) Landwin: 2005T011R (contact pins) Mechanical Drawings (“-MU” Suffix for U-Base Construction/12 V, 24 V and 48 V) 39.2 120 30 (2X) 16.2 PEM F-M3-1 (2X) 2.5 mm max penetration depth from face of side chassis INPUT CONNECTOR DINKLE EHK762V-03P TORQUE: 4kgf-cm MAX. PE N L C40 L-0P J306 FAN CONNECTOR OUTPUT TERMINALS SCREW M4X8 (4X) TORQUE: 10kgf-cm MAX. J304 20-WAY SIGNAL CONNECTOR L1 D1 PEM F-M3-1 (2X) 120 Thermal Hot Spot Reference 75 (2X) PEM F-M3-1 (4X) 3.0 MM MAX PENETRATION DEPTH FROM FACE OF BOTTOM CHASSIS 26.2 101.6 0.5 13.3 16.2 39.2 0.5 30 (2X) MODEL LABEL VR408 TRIMPOT FOR OUTPUT ADJUSTABILITY COUNTER-CLOCKWISE: INCREASE OUTPUT VOLTAGE Temperature Limit (-MU) 105 °C L1 (PFC choke) 115 °C C40 (output cap) 100 °C L-output (output choke) 125 °C Do not exceed indicated temperature limits to ensure operation is within the component thermal derating limits. Measure the component temperatures using K type thermocouples. 100 (2X) 152.4 0.5 Component D1 (AC bridge diode) 1.9 REF Unit weight (-MU suffix): 800 g CNS650-M Series Data Sheet Mechanical Drawings (“-MF” Suffix for Open-frame Construction/12 V only) 152.4 0.5 4.5 43.9 1 RoHS LABEL PE N L INPUT CONNECTOR DINKLE EHK762V-03P TORQUE: 4kgf-cm MAX. C40 88.3 88.8 L-0P OUTPUT TERMINALS SCREW M4X8 (4X) TORQUE: 10kgf-cm MAX. 96.8 0.5 12.7 1 1.9 REF 141.9 J304 20-WAY SIGNAL CONNECTOR 4.5 D1 143.4 4X M3 MOUNTING HOLE MODEL LABEL 2.5 REF J306 FAN CONNECTOR VR408 TRIMPOT FOR OUTPUT ADJUSTABILITY COUNTER-CLOCKWISE: INCREASE OUTPUT VOLTAGE 34.1 0.5 0.5 REF 4 L1 Thermal Hot Spot Reference Component Temperature Limit (-MF) D1 (AC bridge diode) 120 °C L1 (PFC choke) 120°C C40 (output cap) 100 °C L-output (output choke) 125 °C Do not exceed indicated temperature limits to ensure operation is within the component thermal derating limits. Measure the component temperatures using K type thermocouples. Unit weight (-MF suffix): 650 g CNS650-M Series Data Sheet (2X) 30 Mechanical Drawings (“-ME” Suffix for End-fan Construction/12 V only) PEM F-M3-1 (2X) 120 4.8 REF 177.8 0.5 152.4 OUTPUT TERMINALS SCREW M4X8 (4X) TORQUE: 10kgf-cm MAX. 101.6 0.5 55.8 AC INLET 16.2 20 120 J304 20-WAY SIGNAL CONNECTOR 16.2 1.9 REF PEM F-M3-1 (2X) (2X) 75 13.3 PEM F-M3-1 (4X) (2X) 100 26.2 40 0.5 (2X) 30 MODEL LABEL VR408 TRIMPOT FOR OUTPUT ADJUSTABILITY COUNTER-CLOCKWISE: INCREASE OUTPUT VOLTAGE Unit weight (-ME suffix): 1000 g Level B CNS650-M Series Data Sheet Performance Curves Output Power VS. Input Line Output Power Derating 700 700 600 500 Output Power [Watts] Output Power [Watts] 600 400 300 Convection (MF) Convection (MU) 400 LFM (MF/MU) 200 LFM (MF/MU) ME (End Fan) 200 100 500 400 300 Convection (MF) Convection (MU) 400 LFM (MF/MU) 200 LFM (MF/MU) ME (End Fan) 200 100 0 0 0 10 20 30 40 50 60 70 80 90 90 110 130 150 Figure 1. Output Power vs. Ambient Temperature at Natural Convection and Forced Air Cooling 190 210 230 250 270 Figure 2. Output Power vs. Input Line at Natural Convection and Forced Air Cooling CNS655‐Mx (24V) Efficiency Curve CNS653‐Mx (12V) Efficiency Curve 96% 96% 95% 95% 94% 94% Efficiency (%) Efficiency (%) 170 AC Input Line [Vac] Ambient Temperature [°C] 93% 92% 93% 92% 91% 91% 115 VAC 115 VAC 90% 90% 230 VAC 230 VAC 89% 89% 0 0.2 0.4 0.6 0.8 0 1 0.2 0.4 0.6 0.8 1 Output Load (% of 650W) Output Load (% of 650W) Figure 4. Typical Efficiency for 24 V Output Figure 3. Typical Efficiency for 12 V Output CNS658‐Mx (48V) Efficiency Curve Estimated Service Life vs. Component Temp 96% 150 95% Efficiency (%) Esimated Life 100 93% 75 92% 50 91% 25 115 VAC 90% 0 230 VAC 110 89% 0 0.2 0.4 0.6 0.8 1 105 100 95 90 85 80 75 C40 Temperature [°C] Output Load (% of 650W) Figure 5. Typical Efficiency for 48 V Output Figure 6. Estimated Product Useful Life Based on C40 Case Temperature Lifetime [KHrs] 125 94% CNS650-M Series Data Sheet Accessories Orderable Part Number Description Description J304 (20 Pin) Mating Connector with 0.3m wires attached 73-788-001 PIN 20 PIN 19 PIN 2 PIN 3 PIN 1 300 ± 5 mm CNS-BBAR-KIT 73-769-002 Output Bussbar Extension Kit for Vertical Wire Interface USB to I2C Adaptor for PMBus Communication WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] CNS650-M Series DS 24Aug2016