HA12216F/HA12221F Series Audio Signal Processor for Car Deck (Decode only Dolby B type NR with PB Amp.) REJ03F0132-0600 (Previous: ADE-207-254E) Rev.6.00 Jun 15, 2005 Description HA12216F/HA12221F series are silicon monolithic bipolar IC providing Dolby B type noise reduction, music sensor, PB equalizer system in one chip. Notes: 1. Dolby is a trademark of Dolby Laboratories Licensing Corporation. A license from Dolby Laboratories Licensing Corporation is required for the use of this IC. 2. HA12221F series does not include Dolby B NR. Functions • • • • PB equalizer Music sensor Dolby B NR (Only HA12216F series) Line mute (Tape radio) SW × 2 channel × 1 channel × 2 channel × 2 channel Features • Different type of PB equalizer characteristics selection (120 µs/70 µs) is available with fully electronic control switching built-in. • Changeable to Forward, Reverse-mode for PB head with fully electronic control switching built-in. • Available to change music sensing level by external resistor. • Available to change response of music sensor by external capacitor. • Music sensing level, built-in switch to change a band (MSGV). • NR ON/OFF fully electronic control switching built-in. (Only HA12216F series) • Line mute (Tape radio) control switching built-in. • Available to connect direct with MPU. • These ICs are strong for a cellular phone noise. (18 dB improvement from HA12163) Rev.6.00 Jun 15, 2005 page 1 of 52 HA12216F/HA12221F Series Ordering Information Operating Voltage Product HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F Min Max 6.5 6.8 7.2 Unit 12 12 12 V V V Notes: 1. These ICs are designed to operate on single supply. 2. HA12217F and HA12218F, HA12222F and HA12223F are develop, there meets comply with your demands. Standard Level Product HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F Package Code (Previous Code) PLQP0040JB-A (FP-40B) PLQP0040JB-A (FP-40B) PLQP0040JB-A (FP-40B) PB-OUT Level 300 mVrms 387.5 mVrms 450 mVrms Function Product HA12216F series HA12221F series PB-EQ ❍ ❍ Music Sensor ❍ ❍ Mute ❍ ❍ Dolby B NR ❍ × Parallel-Data Format Pin No. 10 11* 12 13 14 Note: Pin Name TAPE/RADIO NR ON/OFF 120 µ/70 µ Forward/Reverse Search/Repeat Non connection regarding HA12221F series. Rev.6.00 Jun 15, 2005 page 2 of 52 Lo TAPE NR OFF 120 µ (Normal) Forward Search (FF or REV) Hi RADIO NR ON 70 µ (Metal or Chrome) Reverse Repeat (Normal Speed) HA12216F/HA12221F Series Pin Description, Equivalent Circuit (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 18 Terminal Name MSI Note V = VCC/2 Equivalent Circuit Pin Description 1 MS input * V 100k VCC/2 28 3 26 5 23 *2 TAI (L) TAI (R) RAI (L) RAI (R) DET (L) Tape input Radio input (Mute) V = 2.5V VCC Time constant pin for rectifier V GND 8 *2 33 4 *2 DET (R) RIP Bias V = VCC/2 V = 0.28V Ripple filter Dolby bias current input V GND 17 MSDET — Time constant pin for rectifier GND Notes: 1. MS: Music Sensor 2. Non connection regarding HA12221F series. Rev.6.00 Jun 15, 2005 page 3 of 52 HA12216F/HA12221F Series Pin Description, Equivalent Circuit (cont.) (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 25 Terminal Name PBOUT (L) Note V = VCC/2 Equivalent Circuit Pin Description VCC PB output V GND 6 PBOUT (R) 19 MAOUT V = VCC/2 VCC MS amp. output *1 V GND 38 29 2 30 VREF EQOUT (L) EQOUT (R) M-OUT (L) Reference output Equalizer output (120µ) V = VCC/2 VCC Equalizer output (70µ) V GND 1 16 7 M-OUT (R) VCC NC — — 9 22 24 27 Note: 1. MS: Music Sensor Rev.6.00 Jun 15, 2005 page 4 of 52 Power supply No connection HA12216F/HA12221F Series Pin Description, Equivalent Circuit (cont.) (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 34 Terminal Name FIN (L) Note Equivalent Circuit — Pin Description Equalizer intput (Forward) V 37 32 FIN (R) RIN (L) 39 31 RIN (R) NFI (L) 40 10 NFI (R) T/R (Mute) Equalizer intput (Reverse) Negative feedback — Mode control input 22 k 100 k GND 2 11 * 12 13 14 NR ON/OFF 120/70 F/R S/R (MS GV) 15 MSOUT — I 200 MS VCC 1 MS output (to MPU) * 100k D GND 20 MS GV (R) 1 V = VCC/2 MS gain terminal * V 90k 21 MS GV (S) 35 GND — 36 Notes: 1. MS: Music Sensor 2. Non connection regarding HA12221F series. Rev.6.00 Jun 15, 2005 page 5 of 52 GND pin HA12216F/HA12221F Series Block Diagram HA12216F Series PBOUT (L) 28 NC 27 26 + 32 T/R F/R 25 NC 24 23 NC 22 21 20 Dolby B NR + 30 29 120/70 − 31 19 + 33 RIP 18 S/R 34 DET 17 + 35 GND + − 36 GND 16 − + LPF VCC 15 MSOUT 37 14 S/R (MS GV) 38 Vref 13 F/R 12 120/70 11 NR ON/OFF 39 F/R 40 120/70 1 T/R + − 2 3 BIAS 4 5 Dolby B NR 6 7 NC PBOUT (R) Rev.6.00 Jun 15, 2005 page 6 of 52 8 9 NC 10 T/R (Mute) HA12216F/HA12221F Series HA12221F Series PBOUT (L) 28 NC 27 26 25 NC 24 NC 23 NC 22 21 20 + 30 29 120/70 − 31 + 32 T/R F/R 19 + 33 RIP 18 S/R 34 DET 17 + 35 GND + − 36 GND 16 − + LPF VCC 15 MSOUT 37 14 S/R (MS GV) 38 Vref 13 F/R 12 120/70 39 F/R 40 120/70 1 T/R + − 11 NC 2 3 4 NC 5 6 7 NC PBOUT (R) Rev.6.00 Jun 15, 2005 page 7 of 52 8 NC 9 NC 10 T/R (Mute) HA12216F/HA12221F Series Functional Description Power Supply Range HA12216F/HA12221F series are provided with three line output level, which will permit on optimum overload margin for power supply conditions. And these are designed to operate on single supply only. Table 1 Supply Voltage Range Product Single Supply HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F 6.5 V to 12.0 V 6.8 V to 12.0 V 7.2 V to 12.0 V Note: The lower limit of supply voltage depends on the line output reference level. The minimum value of the overload margin is specified as 12 dB by Dolby Laboratories. Reference Voltage These devices provide the reference voltage of half the supply voltage that is the signal grounds. As the peculiarity of these devices, the capacitor for the ripple filter is very small about 1/100 compared with their usual value. The block diagram is shown as figure 1. + − 16 VCC + − MS block 38 VREF EQ block (to Line Amp. in case of HA12221F series) 35 36 33 RIP + C15 1µ + − L channel Dolby NR circuit + − R channel Dolby NR circuit : Internal reference voltage Note: HA12221F series does not include Dolby NR circuit. Figure 1 The Block Diagram of Reference Supply Voltage Rev.6.00 Jun 15, 2005 page 8 of 52 HA12216F/HA12221F Series Operating Mode Control HA12216F/HA12221F series provides fully electronic switching circuits. And each operating mode control are controlled by parallel data (DC voltage). When a power supply of this IC is cut off, for a voltage, in addition to a mode control terminal even though as do not destruct it, in series for resistance. Table 2 Threshold Voltage (VTH) Pin No. 10, 11*, 12, 13, 14 Lo –0.2 to 1.0 Hi 3.5 to VCC Unit Test Condition V Input Pin Measure V Note: * Table 3 Non connection regarding HA12221F series. Switching Truth Table Pin No. Lo Hi 10 TAPE RADIO 11* 12 NR OFF 120 µ (Normal) NR ON 70 µ (Metal or Chrome) 13 14 FORWARD SER (FF or REV) REVERSE REP (Normal Speed) Notes: * Non connection regarding HA12221F series. 1. Each pins are on pulled down with 100 kΩ internal resistor. Therefore, it will be low-level when each pins are open. 2. Over shoot level and under shoot level of input signal must be the standardized. (High: VCC, Low: –0.2 V) 3. Reducing pop noise is so much better for 10 kΩ to 22 kΩ resisitor and 1 µF to 22 µF capacitor shown figure 2. Input Pin 10 to 22kΩ + MPU 1 to 22µF Figure 2 Interface for Reduction of Pop Noise Rev.6.00 Jun 15, 2005 page 9 of 52 HA12216F/HA12221F Series Input Block Diagram and Level Diagram PBOUT HA12216F/HA12221F: 300mVrms (−8.2dB) HA12217F/HA12222F: 387.5mVrms (−6.0dB) HA12218F/HA12223F: 450mVrms (−4.7dB) R6 5.1kΩ C2 0.1µF R5 5.1kΩ R2 330kΩ C1 0.01µF TAI RAI 30mVrms 42.4mVrms (−28.2dBs) (−25.2dBs) EQOUT R4 12kΩ M-OUT R3 18kΩ NFI R1 180Ω EQ Amp. − + Input Amp. + − Dolby NR circuit * RIN VREF 0.6mVrms (−62.2dBs) FIN The each level shown above is typical value when offering PBOUT level to PBOUT pin. (EQ Amp. GV = 40dB, f = 1kHz) Note: HA12221F series does not include Dolby NR circuit. Figure 3 Input Block Diagram Adjustment of Playback Reference Operate Level After replace R5 and R6 with a half-fix volume of 10 kΩ, adjust playback reference operate level. Rev.6.00 Jun 15, 2005 page 10 of 52 PBOUT HA12216F/HA12221F Series The Sensitivity Adjustment of Music Sensor Adjusting MS Amp. gain by external resistor, the sensitivity of music sensor can set up. The music sensor block diagram is shown in figure 4, and frequency response is shown in figure 5. VCC 28 +CEX1 REX2 REX1 21 20 MS MS SER REP TAI (L) ×1 −6dB CEX2 + C6 R11 330kΩ 19 18 MA MSI OUT 0.33µF 17 MS DET RL 90kΩ L⋅R signal addition circuit + − C8 0.01µF DVCC − + LPF 25kHz 20dB MSOUT 15 DET MS Amp. GND 36 100kΩ 35 ×1 3 Micro computer TAI (R) Figure 4 Music Sensor Block Diagram GV (dB) GV2 Repeat mode (REP) f1 GV1 10 f4 f3 f2 Search mode (SER) 100 1k f (Hz) 10k Figure 5 Frequency Response Rev.6.00 Jun 15, 2005 page 11 of 52 25k 100k HA12216F/HA12221F Series 1. Serch mode GV1 = 20dB + 20log 1 + 90k [dB] REX2 1 f1 = [Hz], f2 = 25k [Hz] 2π ⋅ CEX2 ⋅ REX2 2. Repeat mode GV2 = 20dB + 20log 1 + 90k [dB] REX1 1 f3 = [Hz], f4 = 25k [Hz] 2π ⋅ CEX1 ⋅ REX1 GVIA: L·R signal addition circuit gain. The sensitivity of music sensor (S) is computed by the formula mentioned below. 3 S = − GV*1 − 20log 130* = 12.7 − GV 30*2 [dB] Note: 1. Search mode: GV1, Repeat mode: G V2 2. Standard level of TAI pin (Dolby level correspondence) = 30 mVrms 3. Standard sensing level of music sensor = 130 mVrms Item REX1, 2 CEX1, 2 GV1, 2 Search mode 24 kΩ 0.01 µF 33.5 dB f1, 3 663 Hz Repeat mode 2.4 kΩ 1 µF 51.7 dB 66.3 Hz f2, 4 25 kHz S (one side channel) –14.8 dB 25 kHz –33.0 dB S (both channel) –20.8 dB –39.0 dB Note: S is 6 dB down in case of one-side channel. And this MS presented hysteresis lest MSOUT terminal should turn over again Hi level or Lo level, in case of thresh S level constantly. Music Sensor Time Constant 1. Sensing no signal to signal (Attack) is determined by C6, 0.01 µF to 1 µF capacitor C6 can be applicable. 2. Sensing signal to no signal (Recovery) is determined by C6 and R11, however preceding (1), 100 kΩ to 1 MΩ can be applicable. Music Sensor Output (MSOUT) As for the internal circuit of music sensor block, music sensor output pin is connected to the collector of NPN type directly, therefore, output level will be “high” when sensing no signal. And output level will be “low” when sensing signal. IL = DVCC − MSOUTLO* RL * MSOUTLO : Sensing signal (about 1V) Note: 1. Supply voltage of MSOUT pin must be less than VCC voltage. Rev.6.00 Jun 15, 2005 page 12 of 52 HA12216F/HA12221F Series The Tolerances of External Components for Dolby NR (Only HA12216F Series) For adequate Dolby NR tracking response, take external components shown below. Also, leak is small capacity, and please employ a good quality object. C10 0.1µF ±10% 23 DET (L) HA12216F Series BIAS 4 R8 18kΩ ±2% DET (R) 8 C4 0.1µF ±10% Figure 6 Tolerance of External Components Countermeasure of a Cellular Phone Noise This IC have reinforced a cellular phone noise countermeasure, to show it hereinafter. However, it is presumed that this effect change it greatly, by a mount set. Please sufficiently examine an arrangement of positions, shield method, wiring pattern, in order to oftain a maximum effect. A high terminal of a noise sensitivity of this IC is FIN, RIN, NFI and RIP. ref HA12216F 1000p FIN 680 + − NFI SG EQOUT 330k 0.01µ 12k AC VM wait DIN/AUDIO 180 Note: Test condition • Use for SG by cellular radio for an evaluation use. • SG output mode PDC system, burst UP Tch (Transmission mode on the side of a movement machine) • To evaluate a capacitor of 1000 pF as connecting with it directly. • About EQOUT output, what you measure through DIN/AUDIO filter. Figure 7 Test Circuit Rev.6.00 Jun 15, 2005 page 13 of 52 HA12216F/HA12221F Series 10 EQOUT Noise Output (dBs) 0 −10 Vin = 0dBm, VCC = 9V, Fin Lch HA12216 & HA12221 HA12163 series HA12192 series −20 −30 −40 −50 −60 100 1000 Frequency (MHz) 10000 Figure 8 EQOUT Noise Output vs. Transmission Frequency Characteristic 10 EQOUT Noise Output (dBs) DIN/AUDIO 0 −10 VCC = 9V, Fin Lch HA12216 & HA12221 HA12163 series HA12192 series −20 −30 −40 −50 −60 −70 −80 −50 −40 −30 −20 −10 0 Higher Harmonic Input Vin (dBm) Figure 9 EQOUT Noise Output vs. Transmission Rev.6.00 Jun 15, 2005 page 14 of 52 10 20 HA12216F/HA12221F Series Absolute Maximum Ratings (Ta = 25°C) Item Maximum supply voltage Power dissipation Operating temperature Storage temperature Symbol VCC Max Pd Topr Tstg Rev.6.00 Jun 15, 2005 page 15 of 52 Rating 16 400 –40 to +85 –55 to +125 Unit V mW °C °C Note Ta ≤ 85°C Rev.6.00 Jun 15, 2005 page 16 of 52 VOM THD-EQ VN VON (1) VON (2) VOL IOH VIL VIH PB-EQ Max output level PB-EQ THD Noise level converted in input MS sensitivity level Νοτε: 1. HA12216F: VCC = 6.5V HA12217F: VCC = 6.8V HA12218F: VCC = 7.2V MS output low level MS output leak current Control voltage PB-EQ gain Crosstalk Vofs Vo max S/N THD CT RL (1) CT RL (2) CT EQ→RAI CT RAI→EQ GV EQ 1k GV EQ 10k(1) GV EQ 10k(2) PBOUT offset Signal handling Signal to noise ratio T.H.D. Channel separation Item Symbol Quiescent current IQ Input Amp. HA12216F GVIA TAI gain GVIA RAI HA12217F GVIA TAI GVIA RAI HA12218F GVIA TAI GVIA RAI DEC-2k (1) B-type decode cut DEC-2k (2) DEC-5k (1) DEC-5k (2) Test Condition 120µ 120µ 120µ 120µ 120µ 70µ 120µ 120µ 120µ OFF ON ON ON OFF OFF OFF OFF F/R F/R F/R T T T FIN EQOUT 1k FIN/RIN EQOUT 1k FIN/RIN EQOUT (1k) R TAI PBOUT 5k S TAI PBOUT 5k S TAI MSOUT 5k MSOUT T↔R PBOUT T TAI PBOUT 1k T TAI PBOUT (1k) T TAI PBOUT 1k R RAI PBOUT 1k F T FIN PBOUT 1k F T→R FIN PBOUT 1k F R→T RAI PBOUT 1k F/R FIN/RIN EQOUT 1k FIN EQOUT 10k F FIN EQOUT 10k F 0 (0) 0 (+12) (+12) (+12) (+12) Min 4.0 18.8 15.8 21.2 18.2 22.5 19.5 2.8 7.0 1.7 6.7 Typ 9.5 19.8 16.8 22.2 19.2 23.5 20.5 4.3 8.5 3.2 8.2 300 THD=1% Vin=3mVrms Rg=680Ω, DIN-AUDIO −36 −18 No signal −0.2 3.5 R 3 5 3 5 3 5 3 L 28 26 28 26 28 26 28 25 25 6 6 15 16 15 15 10 to 14 29 29 29 29 29 25 25 25 25 25 25→6 L R 150 mV 28 6 3 dB 6 3 28 dB (3) (28) 6 0.3 % 6 3 28 dB 3 28 6→25 37 34 dB 37 34 6 26 5 43.0 dB 37/39 34/32 2 39.0 37 34 35.0 37 34 Max Unit 15.0 mA 20.8 dB 17.8 23.2 20.2 24.5 21.5 5.8 dB 10.0 4.7 9.7 Output Application Terminal Input 600 mVrms 37/39 34/32 2 0.1 0.3 % 37/39 34/32 2 0.7 1.5 µVrms (37/39)(34/32) 2 2 28 3 −32 −28 dB −14 −10 V 28 1.0 1.5 3 0.0 2.0 µA V 1.0 VCC VCC=12V, No signal −150 0.0 THD=1% 12.0 13.0 Rg=10kΩ, CCIR/ARM 70.0 80.0 0.05 70.0 80.0 50.0 60.0 70.0 80.0 50.0 60.0 Vin=0.6mVrms 37.0 40.0 33.0 36.0 29.0 32.0 PBOUT fin NR 120µ/ ON/OFF 70µ F/R T/R S/R Input Output (Hz) level (dB) ON 70µ F No signal T S 0 OFF T TAI PBOUT 1k 0 OFF R RAI PBOUT 1k 0 T TAI PBOUT 1k OFF 0 OFF R RAI PBOUT 1k T TAI PBOUT 1k 0 OFF 0 OFF R RAI PBOUT 1k −20 ON T TAI PBOUT 2k −30 T TAI PBOUT 2k ON −20 T TAI PBOUT 5k ON −30 T TAI PBOUT 5k ON IC Condition 1 1 Remark (Ta = 25°C, VCC = 9.0 V, PBOUT Level 300 mVrms(HA12216F) 387.5 mVrms(HA12217F) 450 mVrms(HA12218F)) HA12216F/HA12221F Series Electrical Characteristics HA12216F Series Rev.6.00 Jun 15, 2005 page 17 of 52 VOM THD-EQ VN VON (1) VON (2) VOL IOH VIL VIH PB-EQ Max output level PB-EQ THD Noise level converted in input MS sensitivity level Note: 1. HA12221F: VCC = 6.5V HA12222F: VCC = 6.8V HA12223F: VCC = 7.2V MS output low level MS output leak current Control voltage PB-EQ gain Crosstalk Vofs Vo max S/N THD CT RL (1) CT RL (2) CT EQ→RAI CT RAI→EQ GV EQ 1k GV EQ 10k(1) GV EQ 10k(2) PBOUT offset Signal handling Signal to noise ratio T.H.D. Channel separation Item Symbol Quiescent current IQ Input Amp. HA12221F GVIA TAI gain GVIA RAI HA12222F GVIA TAI GVIA RAI HA12223F GVIA TAI GVIA RAI 120µ 120µ 120µ 120µ 120µ 120µ 120µ 120µ 70µ 120µ/ 70µ 70µ Test Condition F/R F/R F/R T T T T↔R T T T R F T F T→R F R→T F/R F F FIN EQOUT 1k FIN/RIN EQOUT 1k FIN/RIN EQOUT (1k) TAI PBOUT 5k R S TAI PBOUT 5k TAI MSOUT 5k S MSOUT PBOUT TAI PBOUT 1k TAI PBOUT (1k) TAI PBOUT 1k RAI PBOUT 1k FIN PBOUT 1k FIN PBOUT 1k RAI PBOUT 1k FIN/RIN EQOUT 1k FIN EQOUT 10k FIN EQOUT 10k 0 (0) 0 (+12) (+12) (+12) (+12) Min Typ 3.0 5.0 19.0 20.0 16.0 17.0 21.2 22.2 18.2 19.2 22.5 23.5 19.5 20.5 300 THD=1% Vin=3mVrms Rg=680Ω, DIN-AUDIO −36 −18 No signal −0.2 3.5 L 28 26 28 26 28 26 R 3 5 3 5 3 5 R 6 L 25 15 16 15 15 10 to 14 29 29 29 29 150 mV 28 6 25 3 dB 25 6 3 28 dB (3) (28) 25 6 25 6 0.3 % 3 28 dB 3 28 6→25 25→6 37 34 dB 25 37 6 34 5 26 43.0 dB 37/39 34/32 2 29 39.0 37 34 35.0 37 34 20.2 24.5 21.5 Max Unit 8.0 mA 21.0 dB 18.0 23.2 Application Terminal Input Output 600 mVrms 37/39 34/32 2 0.1 0.3 % 37/39 34/32 2 0.7 1.5 µVrms (37/39) (34/32) 2 2 28 3 −32 −28 dB −14 −10 V 28 3 1.0 1.5 0.0 2.0 µA V 1.0 VCC VCC=12V, No signal −150 0.0 THD=1% 12.0 13.0 Rg=10kΩ, CCIR/ARM 70.0 80.0 0.05 70.0 80.0 50.0 60.0 70.0 80.0 50.0 60.0 Vin=0.6mVrms 37.0 40.0 33.0 36.0 29.0 32.0 PBOUT fin F/R T/R S/R Input Output (Hz) level (dB) T S F No signal 0 T TAI PBOUT 1k 0 R RAI PBOUT 1k 0 T TAI PBOUT 1k R RAI PBOUT 1k 0 T TAI PBOUT 1k 0 R RAI PBOUT 1k 0 IC Condition 1 1 Remark (Ta = 25°C, VCC = 9.0 V, PBOUT Level 300 mVrms(HA12221F) 387.5 mVrms(HA12222F) 450 mVrms(HA12223F)) HA12216F/HA12221F Series HA12221F Series HA12216F/HA12221F Series Test Circuit HA12216F Series EQOUT (L) PBOUT (L) R19 10k C19 22µ C20 1µ R27 680 23 NC 22 R1 680 21 20 Dolby B NR T/R R16 C12 2.4k 1µ 19 33 RIP C11 0.01µ R15 330k 18 DET 17 34 35 GND + − 16 − + LPF MSOUT 37 15 S/R (MS Gv) 14 38 Vref VCC DVCC GND NC 24 25 + C1 22µ C10 0.33µ MSOUT R14 C22 100µ 3.9k SW5 SW4 F/R 13 + RIN (R) 26 F/R 36 GND FIN (R) NC 27 C3 0.01µ R17 24k + C21 22µ 32 + R26 680 + FIN (L) 28 + + RIN (L) R23 C18 18k 30 29 0.01µ 120/70 − 31 C14 0.1µ + R24 330k R25 180 C15 2.2µ + R22 12k R18 10k + R21 5.1k C17 0.1µ C24 0.47µ C16 0.47µ + R20 5.1k R29 10k + RAI (L) TAI (L) C2 22µ R2 680 R3 180 R4 330k F/R 39 40 C3 0.01µ 120/70 1 R5 18k R6 12k T/R 2 3 TAI (R) RAI (R) R9 10k EQOUT (R) Note: 1. Resistor tolerance ±1% 2. Capacitor tolerance ±1% 3. Unit R: Ω, C: F Rev.6.00 Jun 15, 2005 page 18 of 52 NR ON/OFF 11 + BIAS 4 5 R10 6 7 NC + C4 18k R7 0.1µ 5.1k + C5 R8 0.47µ 5.1k SW3 120/70 12 Dolby B NR + − C6 2.2µ + C23 0.47µ R11 10k R28 10k PBOUT (R) 8 9 NC C7 0.1µ R13 22k C9 22µ 10 TAP/RAD (Mute) R12 22k + C8 22µ SW2 SW1 HA12216F/HA12221F Series HA12221F Series EQOUT (L) PBOUT (L) R19 10k C19 22µ NC 23 NC 22 21 R16 C12 2.4k 1µ VCC DVCC GND NC 24 25 C20 1µ R27 680 T/R F/R 19 33 RIP R1 680 C11 0.01µ R15 330k 18 DET 17 34 35 GND + − 16 − + LPF MSOUT + C1 22µ 37 15 S/R (MS Gv) 14 38 Vref C10 0.33µ MSOUT R14 C22 100µ 3.9k SW5 SW4 F/R 13 + RIN (R) 26 20 36 GND FIN (R) NC 27 + C21 22µ 32 + R26 680 + FIN (L) 28 + + RIN (L) R23 C18 18k 30 29 0.01µ 120/70 − 31 C3 0.01µ R17 24k + R24 330k R25 180 C15 2.2µ + R22 12k R18 10k + R21 5.1k C17 0.1µ C24 0.47µ C16 0.47µ + R20 5.1k R29 10k + RAI (L) TAI (L) C2 22µ R2 680 R3 180 R4 330k F/R 39 40 C3 0.01µ 120/70 1 R5 18k R6 12k T/R NC 11 2 3 R9 10k EQOUT (R) Rev.6.00 Jun 15, 2005 page 19 of 52 4 NC 5 6 7 NC + C4 R7 0.1µ 5.1k + C5 R8 0.47µ 5.1k TAI (R) RAI (R) Note: 1. Resistor tolerance ±1% 2. Capacitor tolerance ±1% 3. Unit R: Ω, C: F SW3 120/70 12 + − C6 2.2µ + C23 0.47µ R11 10k R28 10k PBOUT (R) 8 NC 9 NC 10 TAP/RAD (Mute) R12 22k + C8 22µ SW1 HA12216F/HA12221F Series Characteristic Curves Quiescent Current vs. Supply Voltage (HA12216F) Quiescent Current IQ (mA) 11 all low 70µ (Other switch is all low) NR-ON VCC = 9.0V NO SIGNAL 10 9 8 6 7 8 9 10 11 Supply Voltage (V) 12 13 Input Amp. Gain vs. Frequency (HA12216F) 26 Gain (dB) 22 VCC = 9.0V TAI →PBOUT RAI NR-OFF TAI 18 RAI 14 10 6 10 100 Rev.6.00 Jun 15, 2005 page 20 of 52 1k 10k Frequency (Hz) 100k 1M HA12216F/HA12221F Series Decode Cut vs. Frequency (HA12216F) 0 0dB −10dB Decode Cut (dB) −2 −20dB −4 −6 −30dB −8 −10 −12 100 −40dB VCC = 9.0V TAI→PBOUT NR-ON 1k Frequency (Hz) 10k 20k Total Harmonic Distortion vs. Frequency (HA12216F) (1) 1 T.H.D. (%) 0dB 10dB −10dB VCC = 9.0V TAI→PBOUT NR-OFF 0.1 0.01 30kHz LPF 0.001 100 Rev.6.00 Jun 15, 2005 page 21 of 52 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k HA12216F/HA12221F Series Total Harmonic Distortion vs. Frequency (HA12216F) (2) 1 T.H.D. (%) 0dB 10dB −10dB VCC = 9.0V TAI→PBOUT NR-ON 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k Total Harmonic Distortion vs. Frequency (HA12216F) (3) 1 T.H.D. (%) 0dB 10dB −10dB VCC = 9.0V RAI→PBOUT NR-OFF 0.1 0.01 30kHz LPF 0.001 100 Rev.6.00 Jun 15, 2005 page 22 of 52 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k HA12216F/HA12221F Series T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12216F) (1) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 NR-OFF 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12216F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 NR-ON 0.1 0.01 −15 Rev.6.00 Jun 15, 2005 page 23 of 52 −10 −5 0 5 10 Output Level Vout (dB) 15 20 HA12216F/HA12221F Series T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12216F) (3) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V RAI→PBOUT 0dB = 300mVrms 1 NR-OFF 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Total Harmonic Distortion vs. Supply Voltage (HA12216F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms NR-OFF T.H.D. (%) 0.1 0.01 0.001 5 Rev.6.00 Jun 15, 2005 page 24 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12216F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms NR-ON T.H.D. (%) 0.1 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12216F) (3) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) RAI→PBOUT = 300mVrms NR-OFF T.H.D. (%) 0.1 0.01 0.001 5 Rev.6.00 Jun 15, 2005 page 25 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Signal Handling (HA12216F) 40 TAI NR-OFF TAI NR-ON RAI NR-OFF 35 Vomax (dB) 30 TAI →PBOUT = 300mVrms RAI f = 1kHz T.H.D. = 1% 25 20 15 10 5 0 6 7 8 9 10 11 12 13 Supply Voltage (V) 14 15 16 Signal to Noise Ratio vs. Supply Voltage (HA12216F) 90 Signal to Noise Ratio (dB) 85 80 75 TAI NR-OFF TAI NR-ON RAI NR-OFF 70 TAI →PBOUT = 300mVrms RAI f = 1kHz CCIR/ARM filter 65 5 Rev.6.00 Jun 15, 2005 page 26 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Equalizer Amp. Gain vs. Frequency (HA12216F) 70 60 EQ Gain (dB) 50 120µ 40 30 70µ 20 10 0 −10 10 VCC = 9.0V FIN→EQOUT 100 1k 10k Frequency (Hz) 100k 1M Total Harmonic Distortion vs. Frequency (HA12216F) 1 T.H.D. (%) 120µ 70µ VCC = 9.0V FIN→EQOUT 0dB = 60mVrms Vout = +20dB 0.1 0.01 30kHz LPF 0.001 100 Rev.6.00 Jun 15, 2005 page 27 of 52 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12216F) (1) 10 T.H.D. (%) 1 0.1 0.01 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 0dB = 60mVrms 120µ 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12216F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 1 0dB = 60mVrms 70µ 0.1 0.01 0.001 −5 Rev.6.00 Jun 15, 2005 page 28 of 52 0 5 10 15 20 25 Output Level Vout (dB) 30 35 HA12216F/HA12221F Series T.H.D. (%) Total Harmonic Distortion vs. Supply Voltage (HA12216F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms Vout = +20dB 120µ 0.1 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 T.H.D. (%) Total Harmonic Distortion vs. Supply Voltage (HA12216F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms Vout = +20dB 70µ 0.1 0.01 0.001 5 Rev.6.00 Jun 15, 2005 page 29 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Signal Handling (HA12216F) 45 FIN 120µ FIN 70µ RIN 120µ RIN 70µ 40 Vomax (dB) 35 FIN →EQOUT RIN 0dB = 60mVrms f = 1kHz T.H.D. = 1% 30 25 20 15 6 8 10 12 Supply Voltage (V) 14 16 Signal to Noise Ratio vs. Supply Voltage (HA12216F) 80 Signal to Noise Ratio (dB) 75 70 120µ 70µ FIN→EQOUT 0dB = 60mVrms f = 1kHz DIN-AUDIO filter 65 60 55 50 45 40 5 Rev.6.00 Jun 15, 2005 page 30 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Ripple Rejection Ratio vs. Frequency (HA12216F) (1) 20 Ripple Rejection Ratio R.R.R. (dB) VCC = 9.0V Vin = 100mVrms PBOUT 0 −20 PBOUT (TAI) NR-OFF −40 PBOUT (TAI) NR-ON PBOUT (RAI) NR-OFF −60 10 100 1k Frequency (Hz) 10k 100k Ripple Rejection Ratio vs. Frequency (HA12216F) (2) Ripple Rejection Ratio R.R.R. (dB) 20 VCC = 9.0V Vin = 100mVrms EQOUT FOR mode 0 −20 EQOUT 120µ −40 −60 10 Rev.6.00 Jun 15, 2005 page 31 of 52 EQOUT 70µ 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series Channel Separation vs. Frequency (HA12216F) (1) −30 Channel Separation (dB) −40 VCC = 9.0V FIN→PBOUT 0dB = 300mVrms Vout = +12dB −50 −60 R→L L→R −70 −80 10 100 Channel Separation (dB) 10k 100k Channel Separation vs. Frequency (HA12216F) (2) −10 −30 1k Frequency (Hz) VCC = 9.0V RAI→PBOUT Vin = +12dB −50 −70 −90 L→R −110 R→L −130 10 100 Rev.6.00 Jun 15, 2005 page 32 of 52 10k 1k Frequency (Hz) 100k 1M HA12216F/HA12221F Series Crosstalk (FIN→RAI) vs. Frequency (HA12216F) −50 Crosstalk (dB) −60 FIN RIN VCC = 9.0V 0dB = 300mVrms Vout = +12dB −70 −80 −90 −100 10 100 100k 1M Crosstalk (mode) vs. Frequency (HA12216F) −20 −30 10k 1k Frequency (Hz) VCC = 9.0V PBOUT Vin = +12dB −40 Crosstalk (dB) −50 RAI→TAI −60 −70 TAI→RAI −80 −90 −100 −110 −120 10 Rev.6.00 Jun 15, 2005 page 33 of 52 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series MS Amp. Gain vs. Frequency (HA12216F) (1) 50 VCC = 9.0V TAI (SER mode) 40 Gain (dB) 30 MAOUT 20 10 MSI 0 −10 −20 10 100 1k Frequency (Hz) 10k 100k MS Amp. Gain vs. Frequency (HA12216F) (2) 50 MAOUT 40 Gain (dB) 30 20 MSI 10 0 −10 VCC = 9.0V TAI (REP mode) −20 10 Rev.6.00 Jun 15, 2005 page 34 of 52 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series MS Sensing Level vs. Frequency (HA12216F) 10 MS Sensing Level (dB) 0 SER L→H SER H→L REP L→H REP H→L VCC = 9.0V TAI→PBOUT 0dB = 300mVrms −10 −20 −30 −40 10 100 10k 1k Frequency (Hz) 100k No-Signal Sensing Time vs. Resistance (HA12216F) No-Signal Sensing Time (ms) 1000 100 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT NR-OFF f = 5kHz PBOUT 10 MSOUT C10 0.33µ 17 VCC R15 1 10k 100k 1M Resistance R15 (Ω) Rev.6.00 Jun 15, 2005 page 35 of 52 10M HA12216F/HA12221F Series Signal Sensing Time vs. Capacitance (HA12216F) Signal Sensing Time (ms) 1000 100 10 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT NR-OFF f = 5kHz PBOUT MSOUT 1 C10 17 VCC R15 330k 0.1 0.001 Rev.6.00 Jun 15, 2005 page 36 of 52 0.01 0.1 Capacitance C10 (µF) 1 10 HA12216F/HA12221F Series Quiescent Current vs. Supply Voltage (HA12221F) 7 Quiescent Current IQ (mA) all low 70µ (Other switch is all low) VCC = 9.0V NO SIGNAL 6 5 4 6 7 8 9 10 11 Supply Voltage (V) 12 13 Input Amp. Gain vs. Frequency (HA12221F) 26 VCC = 9.0V TAI →PBOUT RAI Gain (dB) 22 TAI 18 RAI 14 10 6 10 100 Rev.6.00 Jun 15, 2005 page 37 of 52 1k 10k Frequency (Hz) 100k 1M HA12216F/HA12221F Series Total Harmonic Distortion vs. Frequency (HA12221F) (1) 1 T.H.D. (%) Vin = 0dB Vin = 10dB Vin = −10dB VCC = 9.0V TAI→PBOUT 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k Total Harmonic Distortion vs. Frequency (HA12221F) (2) 1 T.H.D. (%) Vin = 0dB Vin = 10dB Vin = −10dB VCC = 9.0V RAI→PBOUT 0.1 0.01 30kHz LPF 0.001 100 Rev.6.00 Jun 15, 2005 page 38 of 52 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k HA12216F/HA12221F Series T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12221F) (1) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12221F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V RAI→PBOUT 0dB = 300mVrms 1 0.1 0.01 −15 Rev.6.00 Jun 15, 2005 page 39 of 52 −10 −5 0 5 10 Output Level Vout (dB) 15 20 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12221F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms T.H.D. (%) 0.1 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12221F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) RAI→PBOUT = 300mVrms T.H.D. (%) 0.1 0.01 0.001 5 Rev.6.00 Jun 15, 2005 page 40 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Signal Handling (HA12221F) 40 35 Vomax (dB) 30 TAI RAI TAI →PBOUT = 300mVrms = 0dB RAI f = 1kHz T.H.D. = 1% 25 20 15 10 5 0 6 7 8 9 10 11 12 13 Supply Voltage (V) 14 15 16 Signal to Noise Ratio vs. Supply Voltage (HA12221F) 90 Signal to Noise Ratio (dB) 85 80 75 TAI RAI 70 TAI →PBOUT = 300mVrms = 0dB RAI f = 1kHz CCIR/ARM filter 65 5 Rev.6.00 Jun 15, 2005 page 41 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Equalizer Amp. Gain vs. Frequency (HA12221F) 80 70 60 EQ Gain (dB) 50 120µ 40 30 70µ 20 10 0 −10 −20 10 VCC = 9.0V FIN→EQOUT 100 1k 10k Frequency (Hz) 100k 1M Total Harmonic Distortion vs. Frequency (HA12221F) 1 T.H.D. (%) 120µ 70µ VCC = 9.0V FIN→EQOUT 0dB = 60mVrms Vout = +20dB 0.1 0.01 30kHz LPF 0.001 100 Rev.6.00 Jun 15, 2005 page 42 of 52 400Hz HPF + 30kHz LPF 1k Frequency (Hz) 400Hz HPF + 80kHz LPF 10k 20k HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12221F) (1) 10 T.H.D. (%) 1 0.1 0.01 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 0dB = 60mVrms 120µ 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 T.H.D. (%) Total Harmonic Distortion vs. Output Level (HA12221F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 1 0dB = 60mVrms 70µ 0.1 0.01 0.001 −5 Rev.6.00 Jun 15, 2005 page 43 of 52 0 5 10 15 20 25 Output Level Vout (dB) 30 35 HA12216F/HA12221F Series T.H.D. (%) Total Harmonic Distortion vs. Supply Voltage (HA12221F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms = 0dB Vout = +20dB 120µ 0.1 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 T.H.D. (%) Total Harmonic Distortion vs. Supply Voltage (HA12221F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms = 0dB Vout = +20dB 70µ 0.1 0.01 0.001 5 Rev.6.00 Jun 15, 2005 page 44 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Signal Handling (HA12221F) 45 FIN 120µ FIN 70µ RIN 120µ RIN 70µ 40 Vomax (dB) 35 FIN →EQOUT RIN 0dB = 60mVrms f = 1kHz T.H.D. = 1% 30 25 20 15 6 8 10 12 Supply Voltage (V) 14 16 Signal to Noise Ratio vs. Supply Voltage (HA12221F) 80 Signal to Noise Ratio (dB) 75 70 120µ 70µ FIN→EQOUT 0dB = 60mVrms f = 1kHz DIN-AUDIO filter 65 60 55 50 45 40 5 Rev.6.00 Jun 15, 2005 page 45 of 52 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 HA12216F/HA12221F Series Ripple Rejection Ratio vs. Frequency (HA12221F) (1) 20 Ripple Rejection Ratio R.R.R. (dB) 10 VCC = 9.0V Vin = 100mVrms PBOUT 0 −10 −20 −30 PBOUT (TAI) −40 −50 PBOUT (RAI) −60 −70 −80 10 100 1k Frequency (Hz) 10k 100k Ripple Rejection Ratio vs. Frequency (HA12221F) (2) 20 Ripple Rejection Ratio R.R.R. (dB) 10 0 VCC = 9.0V Vin = 100mVrms EQOUT FOR mode −10 −20 EQOUT (120µ) −30 −40 EQOUT (70µ) −50 −60 −70 −80 10 Rev.6.00 Jun 15, 2005 page 46 of 52 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series −30 Channel Separation (dB) −40 Channel Separation vs. Frequency (HA12221F) (1) VCC = 9.0V FIN→PBOUT 0dB = 300mVrms Vout = +12dB −50 −60 R→L L→R −70 −80 10 100 1k Frequency (Hz) 10k 100k Channel Separation vs. Frequency (HA12221F) (2) 0 −10 VCC = 9.0V RAI→PBOUT Vin = +12dB Channel Separation (dB) −20 −30 −40 −50 −60 −70 −80 R→L −90 L→R −100 10 100 Rev.6.00 Jun 15, 2005 page 47 of 52 1k 10k Frequency (Hz) 100k 1M HA12216F/HA12221F Series Crosstalk (FIN→RAI) vs. Frequency (HA12221F) −50 Crosstalk (dB) −60 FIN RIN VCC = 9.0V 0dB = 300mVrms Vout = +12dB −70 −80 −90 −100 10 100 10k 1k Frequency (Hz) 1M Crosstalk vs. Frequency (HA12221F) −20 −30 100k VCC = 9.0V PBOUT Vin = +12dB −40 Crosstalk (dB) −50 RAI→TAI −60 −70 TAI→RAI −80 −90 −100 −110 −120 10 Rev.6.00 Jun 15, 2005 page 48 of 52 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series MS Amp. Gain vs. Frequency (HA12221F) (1) 50 VCC = 9.0V TAI (SER mode) Gain (dB) 40 30 MAOUT 20 10 MSI 0 10 100 1k Frequency (Hz) 10k 100k MS Amp. Gain vs. Frequency (HA12221F) (2) 50 VCC = 9.0V TAI (REP mode) Gain (dB) 40 MAOUT 30 20 MSI 10 0 10 Rev.6.00 Jun 15, 2005 page 49 of 52 100 1k Frequency (Hz) 10k 100k HA12216F/HA12221F Series MS Sensing Level vs. Frequency (HA12221F) 10 MS Sensing Level (dB) 0 SER L→H SER H→L REP L→H REP H→L VCC = 9.0V TAI→PBOUT 0dB = 300mVrms −10 −20 −30 −40 10 100 10k 1k Frequency (Hz) 100k No-Signal Sensing Time vs. Resistance (HA12221F) No-Signal Sensing Time (ms) 1000 100 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT f = 5kHz PBOUT 10 MSOUT C10 0.33µ 17 VCC R15 1 10k 100k 1M Resistance R15 (Ω) Rev.6.00 Jun 15, 2005 page 50 of 52 10M HA12216F/HA12221F Series Signal Sensing Time vs. Capacitance (HA12221F) Signal Sensing Time (ms) 1000 100 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT f = 5kHz 10 PBOUT MSOUT 1 C10 17 VCC R15 330k 0.1 0.001 Rev.6.00 Jun 15, 2005 page 51 of 52 0.01 0.1 Capacitance C10 (µF) 1 10 HA12216F/HA12221F Series Package Dimensions JEITA Package Code P-LQFP40-7x7-0.65 RENESAS Code PLQP0040JB-A Previous Code FP-40B MASS[Typ.] 0.2g NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. HD *1 D 30 21 31 20 bp Reference Symbol D c c1 HE Dimension in Millimeters Min Nom Max 7.0 E 7.0 A2 1.40 *2 E b1 ZE Terminal cross section 11 40 Index mark c A A1 L L1 Detail F bp y x M 9.2 A1 0.08 0.13 0.22 bp 0.20 0.25 0.30 θ 0.22 0.12 0.17 0.22 0.15 0° e 8° 0.65 x 0.13 y 0.10 0.575 ZD 0.575 ZE L L1 Rev.6.00 Jun 15, 2005 page 52 of 52 9.2 1.70 c1 θ *3 9.0 c F e 9.0 8.8 b1 A2 ZD 8.8 A 10 1 HD HE 0.40 0.50 1.0 0.60 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 2.0