The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. NEW Push-on Bayonet Lock Miniature Waterproof Connector HR34B Series Push-on Bayonet Lock Mating : Just inserting plug unit will complete mating Un-mating : Rotating sleeve to unlock mating fig.1 ■Features Cable exit directions 1. Water and dust protection • IP67 water and dust protection rating when fully mated. • Resistant to industrial grade oils. • 4-position receptacles are sealed against water penetration when mounted on the panel - no protective cap is required. 45˚ 2. Easy and precise mating • Mating: Just inserting plug unit completes mating Unmating: Rotating sleeve counterclockwise unlocks connectors (fig.1) • Marking helps align plug with receptacle when mating. • 3 guide keys make blind mating possible. (Receptacle structure prevents plug from damaging receptacle terminals) fig.2 3. Multi-directional cable exit Right angle plugs allow the cable to exit in 8 directions, in 45˚ increments.(fig.2) 4. Safty standards The 4-position connectors meet requirements of T ÜV standard. 5. Wide variation Item Number of positions Connector type Terminations(plug) Terminations(receptacle) Conduit material Applicable cable size 4,10 straight plug,right angle plug,receptacle solder,crimp panel mount through-hole,wire solder plastic,metal Ø5.3~7.3, Ø6.5~8.0, Ø8.0~9.0(under development) 2010.52 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Specifications Current rating 10 pos.: 3 A 4 pos. : 5 A Operating temperature range -25°C to 125°C Voltage rating 10 pos.: 200 V AC, 250 V DC 4 pos. : 200 V AC, 200 V DC (contamination level 3) 400 V AC, 400 V DC (contamination level 2) Storage temperature range -25°C to 85°C Ratings Item 1.Contact resistance 2.Insulation resistance 30 mø max. 1,000 Mø min. Specification Conditions 1 A DC 500 V DC 10 pos. : 900 V AC / 1 minute 4 pos. : 2,000 V AC / 1 minute 3.Withstanding voltage No flashover or insulation breakdown 4.Vibration No electrical discontinuity of 10 µs or longer Frequency: 10 to 500 Hz/cycle, total amplitude of 0.75 mm, 98m/s2 each, 3 hours in 3 axis. 5.Shock No electrical discontinuity of 10 µs or longer Acceleration of 490 m/s2, 11 ms duration, 3 axis, each for 3 hours 6.Durability (Mating / un-mating) Contact resistance: 30 mø max. 500 cycles 7.Temperature cycle Insulation resistance: 500 Mø min. Temperature :-55°C / +15° to +35°C / +85°C / +15° to +35°C Time :-30 min. / 10 to 15 min. / 30 min. / 10 to 15 min. 5 cycles 8.Humidity Insulation resistance: 50 Mø min. (at high humidity) Insulation resistance: 500 Mø min. (when dry) 336 hours at 71°C, and humidity of 95% 9.Water protection No water penetration when submerged for 48 hours at the depth of 1.8 meters. ■Materials ●Plugs Part Material Zinc alloy, aluminum alloy, and polyamide resin (black) Outer shell Insulator Female contacts 10 pos. 4 pos. O-ring Gasket PPS Phosphor bronze Copper alloy Fluororubber, Nitrile hydride rubber Finish Black chrome plating, black chromate finish (Cr +3) Remarks --------------- Color: Black Gold plated Silver plated UL94V-0 ----------------------------- --------------- --------------- ●Receptacles Part Outer shell Insulator Male contacts Ground contact O-ring 2 10 pos. 4 pos. 10 pos. 4 pos. Material Zinc alloy PPS Copper alloy Brass Brass Fluororubber Finish Black chromate finish (Cr +3) Color: Black Gold plated Silver plated Gold plated Silver plated --------------- Remarks --------------UL94V-0 ----------------------------------------------------------------------- The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Ordering information ●Plugs HR34B - 12 WP A - 10 S - X ( ** ) 1 2 3 4 5 6 1 Series name 2 Shell size 3 Shell style : HR34B Series : Diameter(mm) of the mating interface of the plug WP : Straight plug WLP : Right-angle plug 4 Conduit material and Applicable cable size A:Conduit material metal, Applicable cable Ø5.3~7.3 B:Conduit material metal, Applicable cable Ø6.5~8.0 D:Conduit material plastic, Applicable cable Ø5.7~7.3 E:Conduit material plastic, Applicable cable Ø6.5~8.0 K:Conduit material metal, Applicable cable Ø8.0~9.0(under development) 7 8 5 Number of contact : Number of contacts. (Excluding ground contacts) 6 Contact type S : Female wire solder SC : Female crimp 7 Keying Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specifications change other than shown in positions q to u ●Receptacles HR34B - 12 WR A - 10 P - X ( ** ) 1 1 2 3 4 3 2 4 5 Series name : HR34B Series Shell size : Diameter(mm) of the mating interface of the plug Shell style WR : Receptacl Shell type Blank : Rectangular flange type for 10 positions A : Square flange for 10 positions B : Square flange for 4 positions 6 7 8 5 Number of contact : Number of contacts. (Excluding ground contacts) 6 Contact type P : Male,wire solder PD : Male,through hole contact 7 Keying Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specification change other than shown in positions q to u ●Crimp contacts HR34B - SC1 - 2 1 1 1 2 1 Series name : HR34B Series 2 Contact style : SC1:Female contact 3 Contact type 3 4 5 4 Conductor size : AWG#20 - 25 5 Plating 1:Gold plated 1 : 100pcs.per bag 2 : 10,000pcs per reel 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Straight plugs ●Standard type (Conduit material :Plastic) ◆Wire solder Part Number A Ø19 49 All dimensions: mm HRS No. A Applicable cable diameter range HR34B-12WPD-10S 134-0026-0-00 Ø7.4 Ø5.7~7.3 HR34B-12WPE-10S 134-0027-2-00 Ø8.5 Ø6.5~8.0 HR34B-12WPD-4S 134-0020-3-00 Ø7.4 Ø5.7~7.3 HR34B-12WPD-4S-X 134-0023-1-00 HR34B-12WPE-4S 134-0025-7-00 Ø8.5 Ø6.5~8.0 HR34B-12WPE-4S-X 134-0031-0-00 HRS No. A Applicable cable diameter range HR34B-12WPD-10SC 134-0037-6-00 Ø7.4 Ø5.7~7.3 HR34B-12WPE-10SC 134-0038-9-00 Ø8.5 Ø6.5~8.0 Solder cup inner diameter Ø1 Ø1.7 ◆Crimp (separate contacts required) Part Number ●Robust type(Conduit material :Metal) ◆Wire solder Part Number HR34B-12WPA-10S(71) HR34B-12WPB-10S(71) HR34B-12WPK-10S All dimensions: mm HRS No. A Applicable cable diameter range 134-0004-7-71 Ø7.4 Ø5.7~7.3 134-0007-5-71 Ø8.5 Ø6.5~8.0 Under development Ø9.5 Ø8.0~9.0 ●Crimp (separate contacts required) Part Number HRS No. A Applicable cable diameter range 134-0017-9-00 Ø7.4 Ø5.7~7.3 HR34B-12WPB-10SC 134-0028-5-00 Ø8.5 Ø6.5~8.0 HR34B-12WPK-10SC Under development Ø9.5 Ø8.0~9.0 HR34B-12WPA-10SC Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use. 4 Solder cup inner diameter Ø1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Right angle plugs ●Standard type (Conduit material : Plastic) B 33.5 A Ø19 ◆Wire solder Part Number All dimensions: mm HRS No. A HR34B-12WLPD-10S 134-0039-1-00 Ø7.4 Ø5.7~7.3 HR34B-12WLPE-10S 134-0040-0-00 Ø8.5 Ø6.5~8.0 HR34B-12WLPD-4S 134-0030-7-00 HR34B-12WLPD-4S-X 134-0034-8-00 HR34B-12WLPE-4S 134-0035-0-00 HR34B-12WLPE-4S-X 134-0036-3-00 Ø7.4 B 30.85 Applicable cable diameter range Solder cup inner diameter Ø1 Ø5.7~7.3 Ø1.7 Ø8.5 Ø6.5~8.0 ◆Crimp (separate contacts required) Part Number HRS No. A HR34B-12WLPD-10SC 134-0041-3-00 Ø7.4 HR34B-12WLPE-10SC 134-0042-6-00 Ø8.5 B 30.85 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 ●Robust type (Conduit material :Metal) ◆Wire solder Part Number All dimensions: mm HRS No. A HR34B-12WLPA-10S(71) 134-0005-0-71 Ø7.4 HR34B-12WLPB-10S(71) 134-0008-8-71 Ø8.5 Under development Ø9.5 31.5 Ø8.0~9.0 B Applicable cable diameter range HR34B-12WLPK-10S B 30.5 Applicable cable diameter range Solder cup inner diameter Ø5.7~7.3 Ø6.5~8.0 Ø1 ●Crimp (separate contacts required) Part Number HRS No. A 134-0018-1-00 Ø7.4 HR34B-12WLPB-10SC 134-0029-8-00 Ø8.5 HR34B-12WLPK-10SC Under development Ø9.5 HR34B-12WLPA-10SC 30.5 31.5 Ø5.7~7.3 Ø6.5~8.0 Ø8.0~9.0 Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Receptacles ◆Wire solder 48) 2. (R 4-Ø 1 3 8 10 B A 4 3.2 7 A B All dimensions: mm HRS No. A B Solder cup inner diameter HR34B-12WRA-10P Part Number 134-0016-6-00 17.26 23.4 Ø1 HR34B-12WRB-4P 134-0021-6-00 18.26 25.4 Ø1.3 HR34B-12WRB-4P-X 134-0024-4-00 O ring for water proof is not attached. Please find appropriate one from the market. ◆Through hole 5.8 8.55 20 3.3 13.4 2 39 Part Number 32.4 3.2 4-Ø HRS No. HR34B-12WR-10PD(71) 134-0003-4-71 O ring for water proof is not attached. Please find appropriate one from the market. ■Crimp contacts ◆Female 1.2 15 Part Number CL No. Applicable conductor AWG #20 - 25 (Stranded wire) HR34B-SC1-111 134-0051-7-00 100 pcs. per bag HR34B-SC1-211 134-0050-1-00 10,000 pcs. per reel Note: Use wire with a jacket diameter of 1.7mm max. 6 Packaging The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Connector Mating Combinations 10 pos. Plugs 10 pos. Receptacles Straight, Wire Solder or Crimp (Standard key position) HR34B-12WPA-10S,10SC HR34B-12WPB-10S,10SC HR34B-12WPD-10S,10SC HR34B-12WPE-10S,10SC HR34B-12WPK-10S,10SC Through hole HR34B-12WR-10PD Right angle, Wire Solder or Crimp (Standard key position) HR34B-12WLPA-10S,10SC HR34B-12WLPB-10S,10SC HR34B-12WLPD-10S,10SC HR34B-12WLPE-10S,10SC HR34B-12WLPK-10S,10SC Wire Solder HR34B-12WRA-10P 4 pos. Plugs 4 pos. Receptacles Straight, Wire Solder (Standard key position) HR34B-12WPD-4S HR34B-12WPE-4S Standard polarizing key Wire solder (Standard key position) HR34B-12WRB-4P Right angle, Wire Solder (Standard key position) HR34B-12WLPD-4S HR34B-12WLPE-4S Standard key position Straight, Wire Solder (X key position) HR34B-12WPD-4S-X HR34B-12WPE-4S-X Wire solder (X key position) HR34B-12WRB-4P-X Right angle, Wire Solder (X key position) HR34B-12WLPD-4S-X HR34B-12WLPE-4S-X X key position X key position 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector ■Applicable tools Description Part Number CL No. Applicable contact Applicable cable Manual contact crimping tool HT304/HR34B-1 150-0107-9 HR34B-SC1-111 AWG20,AWG23,AWG25 Press CM-105 901-0005-4 HR34B-SC1-211 AWG20 to AWG25 Applicator AP105-HR34B-1 901-2051-2 Contact extraction tool RP6-SC-TP 150-0039-0 HR34B-SC1-111 --------------- HR34B-SC1-211 ●Manual contact crimping tool ●Press CM-105 (Applicator ordered separate) ●Contact extraction tool ■Illustrations of mated connectors. Right-angle plug Mating Combinations 10 pos. plug shell A,B type. 10 pos. plug shell D,E type. 10 pos. plug shell K type. (33.5) 31.0 Plug + receptacle wire solder 31.5 Plug + receptacle through-hole 31.3 Plug + receptacle wire solder 31.8 Plug + receptacle through-hole 32.0 Plug + receptacle wire solder 32.5 4 pos.plug + receptacle wire solder 31.3 B A 8 A Plug + receptacle through-hole Straight plug Mating combinations B 10 pos.plug + receptacle through-hole 49.6 10 pos.plug + receptacle wire solder 50.1 4 pos.plug + receptacle wire solder 49.6 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector BRecommended panel cutouts ●Receptacle - wire solder 4-B All dimensions: mm HR34B-12WRB-4P HR34B-12WRB-4P-X 17.26±0.05 18.26±0.05 A HR34B-12WRA-10P A M3∞0.5 B C A C 1 0/-0.1 1.1 0/-0.1 D 12.5 +0.1/0 16.3 +0.1/0 E 17 +0.1/0 20.8 +0.1/0 Recommended O ring dia. Part Number ØD HR34B-12WRA-10P ØE HR34B-12WRB-4P HR34B-12WRB-4P-X ●Receptacle - through hole Cross-section diameter 1.5 11.5 1.5 15.5 All dimensions: mm (13.6) (22.4) (2.3)(xxx) 5. (R 4- (13.4) 4-M3∞0.5 (1.3) 2) (13.4) (32.4) O-ring (Not supplied, cross-section diameter 1.78 , inner diameter 20.35) Outline of the O-ring (18) Notes 1: The receptacle panel cutout shows the view from the mating side of the connector. BPCB mounting pattern ●Receptacle - Through hole All dimensions: mm 2.15 (G 10 7 Ø1 2-Ø 1.4 +0 .0 0 5 1.2 3.6 4 8 3 0 te d n ou 1.2 3.6 0 1 0. + 0 1 .9 +0.1 2.4 -Ø0 10 rm r 2.4 17 0° ±3 5.5 Alignment mark ) al in 4.4 2.15 (Po siti oni ng pos t) N ote 3 Note 1: The contact configuration shows the view from the mating side. Note 2: Tolerance of ±0.05 mm is recommended for the plated through hole location and diameter. Note 3: Not a plated-through holes. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B Series●Push-on Bayonet Lock Miniature Waterproof Connector BReceptacle Contact Arrangement 4 pos.wire solder 10 pos.wire solder 1 2 1 4 3 2 5 8 1 3 6 9 10 pos.through hole 4 7 8 10 2 5 3 6 9 7 10 note.1 View direction:Mating surface of pin insert. note.2 mark is ground terminal. BHandling 1. Mating 2. Un-mating Receptacle Plug Locking collar B A Rotate counter-clockwise Mating position alignment marks Holding the plug by the outer shell (A) align the arrow on the plug with the alignment mark on the receptacle and push straight in. Rotate the locking collar counter-clockwise to a full stop and unmate the plug from the receptacle. BPrecautions Center line of the connector When completely mated and locked the alignment arrow on the plug must line-up with the center line of the connector (alignment mark on the receptacle). Alignment mark If the alignment arrow and the center line of the connectors are not aligned (1 mm max.) re-insert the plug until they are aligned. 1 mm max. 1. When disconnecting or inserting the connector, be sure to do so after turning off the power. 2. To insert the connector, push it in until the arrow tip of the plug mating mark indicates the specified position of the diagram below (i.e., the mating mark of the receptacle). 3. Note that the display method of the mating mark will differ depending on the receptacle. 4. To maintain the waterproof quality and cable clamp force, use a cable that is within the range of the applicable cable diameter. 5. Please consult Hirose Electric Sales for harness assembly procedure. 10