Finisar Product Specification Multiprotocol 10Gb/s DWDM XFP Optical Transceiver FTLX3812M3xx PRODUCT FEATURES • Supports 9.95Gb/s to 11.1Gb/s • Hot-pluggable XFP footprint • Temperature-stabilized DWDM EML transmitter • RoHS-6 Compliant (lead-free) • 100GHz ITU Grid, C-Band • Duplex LC connector • Power dissipation <3.5W • Built-in digital diagnostic functions • Temperature range: -5°C to 70°C APPLICATIONS • Amplified DWDM 10G SONET/SDH • Amplified DWDM 10G Ethernet Finisar’s FTLX3812M3xx Small Form Factor 10Gb/s (XFP) transceiver complies with the current XFP Multi-Source Agreement (MSA) Specification1. It supports amplified DWDM 10Gb/s SONET/SDH and 10-Gigabit Ethernet applications. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. For a SONET-only version, please see FTLX3812S3xx. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC3, and Finisar Application Note AN-20384. PRODUCT SELECTION FTLX3812M3xx xx: 100GHz ITU-T channel (see next page) © Finisar Corporation 28-September-2007 Rev B1 Page 1 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 Channel # 17* 18* 19* 20* 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60* 61* Product Code FTLX3812M317 FTLX3812M318 FTLX3812M319 FTLX3812M320 FTLX3812M321 FTLX3812M322 FTLX3812M323 FTLX3812M324 FTLX3812M325 FTLX3812M326 FTLX3812M327 FTLX3812M328 FTLX3812M329 FTLX3812M330 FTLX3812M331 FTLX3812M332 FTLX3812M333 FTLX3812M334 FTLX3812M335 FTLX3812M336 FTLX3812M337 FTLX3812M338 FTLX3812M339 FTLX3812M340 FTLX3812M341 FTLX3812M342 FTLX3812M343 FTLX3812M344 FTLX3812M345 FTLX3812M346 FTLX3812M347 FTLX3812M348 FTLX3812M349 FTLX3812M350 FTLX3812M351 FTLX3812M352 FTLX3812M353 FTLX3812M354 FTLX3812M355 FTLX3812M356 FTLX3812M357 FTLX3812M358 FTLX3812M359 FTLX3812M360 FTLX3812M361 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Finisar Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77 *This channel is supported with limited availability -- Please contact Finisar for further details. © Finisar Corporation 28-September-2007 Rev B1 Page 2 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 I. Finisar Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional –5.2 Power Supply – Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply Module Ground Reference Clock non-inverted input, AC coupled on the host board – Not required Reference Clock inverted input, AC coupled on the host board – Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V and 3.6V. © Finisar Corporation 28-September-2007 Rev B1 Page 3 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 Finisar Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage #1 Maximum Supply Voltage #2 Maximum Supply Voltage #3 Storage Temperature Case Operating Temperature Receiver Damage Threshold Symbol Vcc3 Vcc5 Vcc5 TS TOP PRdmg © Finisar Corporation 28-September-2007 Min -0.5 -0.5 -0.5 -40 -5 +1 Rev B1 Typ Max 4.0 6.0 2.0 85 70 Unit V V V °C °C dBm Ref. Page 4 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 III. Finisar Electrical Characteristics (TOP = -5 to 70 °C, VCC5 = 4.75 to 5.25 Volts) Parameter Supply Voltage #1 Supply Voltage #2 Supply Voltage #3 Supply Current – Vcc5 supply Supply Current – Vcc3 supply Supply Current – Vcc2 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Reference Clock Clock differential input impedance Reference Clock frequency Differential clock input swing Clock output rise/fall time Reference clock frequency tolerance Symbol Vcc5 Vcc3 Vcc2 Icc5 Icc3 Icc2 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Rclkin f0 Vclkin,pp trf Df Min 4.75 3.13 1.71 Typ Max 5.25 3.46 1.89 350 400 750 3.5 Unit V V V mA mA mA W Ω mV V V us 2 820 Vcc GND+ 0.8 10 650 mV ps ps V V 4 5 5 6 6 7 100 Baud/64 Ω MHz mV ps PPM 100 120 2.0 GND 340 Vcc – 0.5 GND 640 200 -100 850 38 38 VccHOST GND+0.5 See Note 6 below 1600 1250 +100 Ref. 1 3 5 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 – 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. © Finisar Corporation 28-September-2007 Rev B1 Page 5 Finisar FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 IV. Optical Characteristics (EOL, TOP = -5 to 70°C, VCC5 = 4.75 to 5.25 Volts) Please note that the Transmitter of the FTLX3811M3xx becomes operational within 60 seconds of power-up. This is due to the time required for the EML to reach its optimum operating temperature. Transmitter Parameter Output Opt. Pwr: 9/125 SMF Optical Extinction Ratio Center Wavelength Spacing Transmitter Center Wavelength – End Of Life Transmitter Center Wavelength – Beginning Of Life Sidemode Suppression ratio Tx Jitter Generation (peak-to-peak) Tx Jitter Generation (RMS) Symbol POUT ER Min -3 8.2 λc X-100 100 X λc X-25 X SSRmin Txj TxjRMS 30 Relative Intensity Noise Receiver Maximum Input Power Optical Center Wavelength Receiver Reflectance LOS De-Assert LOS Assert LOS Hysteresis Receiver Sensitivity Data rate (Gb/s) BER 9.95 1e-12 10.3 1e-12 10.7 1e-4 11.1 1e-4 OSNR Performance Data rate (Gb/s) BER Typ RIN PMAX λC Rrx LOSD LOSA -7 1270 Max +3 Ref. X+100 Unit dBm dB GHz pm X+25 pm 2 0.1 0.01 dB UI UI 3 4 -130 dB/Hz 1600 -27 -30 -37 0.5 1 2 dBm nm dB dBm dBm dB Dispersion (ps/nm) Sensitivity back-toback at OSNR>30dB (dBm) Power Penalty at OSNR>30dB (dB) 5 Threshold Adjustm. Required -500 to 1450 -500 to 1450 -500 to 1300 -500 to 1300 -23 -23 -27 -27 3 3 3 3 No No Yes Yes Dispersion (ps/nm) Min OSNR Back-toback at Power: -7 to 18dBm (dB) Max OSNR Penalty at Power:-7 to -18dBm (dB) 6 Threshold Adjustm. Required 9.95 1e-12 -500 to 1450 24 4 No 10.3 1e-12 -500 to 1450 24 4 No 10.7 1e-4 -500 to 1300 16 4 Yes 11.1 1e-4 -500 to 1300 16 4 Yes Notes: 1. Corresponds to approximately 0.8 nm. 2. X = Specified ITU Grid wavelength. Wavelength stability is achieved within 60 seconds of power up. 3. Measured with a host jitter of 50 mUI peak-to-peak. 4. Measured with a host jitter of 7 mUI RMS. 5. Measured at 1528-1600nm with worst ER; BER<10-12; PRBS31. 6. All OSNR measurements are performed with 0.1nm resolution. © Finisar Corporation 28-September-2007 Rev B1 Page 6 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 V. Finisar General Specifications Parameter Bit Rate Max. Supported Link Length Symbol BR LMAX Min 9.95 Typ Max 11.1 80 Units Gb/s km Ref. 1 Notes: 1. Amplified SONET OC-192, 10G Ethernet, SONET OC-192 with FEC, 10G Ethernet with FEC VI. Environmental Specifications Finisar XFP transceivers have an operating temperature range from -5°C to +70°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -5 -40 Typ Max 70 85 Units °C °C Ref. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TÜV R72052602 Electrical Safety Electrical Safety TÜV EN 60825-1: 1994+A11:1996+A2:2001 IEC 60825-1: 1993+A1:1997+A2:2001 IEC 60825-2: 2000, Edition 2 EN 60950 CLASS 3862.07 CLASS 3862.87 1439230 UL/CSA Certificate Number 9210176-77 R72052602 Copies of the referenced certificates are available at Finisar Corporation upon request. © Finisar Corporation 28-September-2007 Rev B1 Page 7 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 Finisar VIII. Digital Diagnostics Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: • • • • • • Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage TEC Temperature It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information, including memory map definitions, please see the XFP MSA documentation1. Receiver Threshold Adjustment The FTLX3812M3xx also provides access to receiver decision threshold adjustment via 2-wire serial interface, in order to improve receiver OSNR performance based on specific link conditions. It is implemented as follows: • • Rx Threshold of XFP transceivers will be factory-set for optimized performance in non-FEC applications. This will be the default value during both cold start (power-up) and warm start (module reset). The transceiver supports adjustment of Rx Threshold value by the host through register 76d, table 01h. This is intended to be used in FEC applications. © Finisar Corporation 28-September-2007 Rev B1 Page 8 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 • • IX. Finisar Register 76d, table 01h is a volatile memory. Therefore if the transceiver is power-cycled, the register starts up with a value of 00h which corresponds to the default Rx Threshold value. The threshold adjustment input value is 2’s complement 7 bit value (-128 to +127), with 0 corresponding to default Rx threshold value. Full range of adjustment provides at least a ±10% change in Rx threshold from the default value. Mechanical Specifications Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). 77.95 22.15 18.35 13.30 8.50 LATCHED 1.95 16.00 UNLATCHED 20.85 39.00 R1.00 XFP Transceiver (dimensions are in mm) © Finisar Corporation 28-September-2007 Rev B1 Page 9 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 X. Finisar PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) © Finisar Corporation 28-September-2007 Rev B1 Page 10 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 Finisar XFP Detail Host Board Mechanical Layout (dimensions are in mm) XFP Recommended Bezel Design (dimensions are in mm) © Finisar Corporation 28-September-2007 Rev B1 Page 11 FTLX3812M3xx Amplified DWDM XFP Product Specification – September 2007 Finisar XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers” – Finisar Corporation, December 2003 3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. 4. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers”, Finisar Corporation, January 21, 2005. XII. Revision History Revision Date A 4/12/2006 • Document created. A1 4/21/2006 • Updated Finisar Address A2 5/22/2006 • Updated BOL wavelength tolerance specification. B 10/25/2006 • Added Safety Certificate numbers. • Document released. B1 9/28/2007 • Updated note on channels. XII. Description For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation 28-September-2007 Rev B1 Page 12