NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 FEATURES • • Timing From Microseconds to Hours Astable or Monostable Operation • • Adjustable Duty Cycle TTL-Compatible Output Can Sink or Source up to 200 mA DESCRIPTION/ORDERING INFORMATION These devices are precision timing circuits capable of producing accurate time delays or oscillation. In the time-delay or monostable mode of operation, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle can be controlled independently with two external resistors and a single external capacitor. The threshold and trigger levels normally are two-thirds and one-third, respectively, of VCC. These levels can be altered by use of the control-voltage terminal. When the trigger input falls below the trigger level, the flip-flop is set, and the output goes high. If the trigger input is above the trigger level and the threshold input is above the threshold level, the flip-flop is reset and the output is low. The reset (RESET) input can override all other inputs and can be used to initiate a new timing cycle. When RESET goes low, the flip-flop is reset, and the output goes low. When the output is low, a low-impedance path is provided between discharge (DISCH) and ground. The output circuit is capable of sinking or sourcing current up to 200 mA. Operation is specified for supplies of 5 V to 15 V. With a 5-V supply, output levels are compatible with TTL inputs. NA555...D OR P PACKAGE NE555...D, P, PS, OR PW PACKAGE SA555...D OR P PACKAGE SE555...D, JG, OR P PACKAGE (TOP VIEW) 1 8 2 7 3 6 4 5 VCC DISCH THRES CONT NC GND NC VCC NC NC TRIG NC OUT NC 4 3 2 1 20 19 18 5 17 6 16 7 15 14 9 10 11 12 13 8 NC DISCH NC THRES NC NC RESET NC CONT NC GND TRIG OUT RESET SE555...FK PACKAGE (TOP VIEW) NC – No internal connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1973–2006, Texas Instruments Incorporated On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 ORDERING INFORMATION TA VTHRES MAX VCC = 15 V PACKAGE (1) PDIP – P 11.2 V NE555P Tube of 75 NE555D Reel of 2500 NE555DR Reel of 2000 NE555PSR Tube of 150 NE555PW Reel of 2000 NE555PWR Tube of 50 SA555P Tube of 75 SA555D Reel of 2000 SA555DR Tube of 50 NA555P Tube of 75 NA555D Reel of 2000 NA555DR Tube of 50 SE555P Tube of 75 SE555D Reel of 2500 SE555DR CDIP – JG Tube of 50 SE555JG SE555JG LCCC – FK Tube of 55 SE555FK SE555FK SOP – PS TSSOP – PW PDIP – P –40°C to 85°C 11.2 V SOIC – D PDIP – P –40°C to 105°C 11.2 V SOIC – D PDIP – P –55°C to 125°C (1) 10.6 TOP-SIDE MARKING Tube of 50 SOIC – D 0°C to 70°C ORDERABLE PART NUMBER SOIC – D NE555P NE555 N555 N555 SA555P SA555 NA555P NA555 SE555P SE555D Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (1) 2 RESET TRIGGER VOLTAGE (1) THRESHOLD VOLTAGE (1) OUTPUT DISCHARGE SWITCH Low Irrelevant Irrelevant Low On High <1/3 VDD Irrelevant High Off High >1/3 VDD >2/3 VDD Low On High >1/3 VDD <2/3 VDD Voltage levels shown are nominal. Submit Documentation Feedback As previously established NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 FUNCTIONAL BLOCK DIAGRAM VCC 8 6 THRES 2 TRIG CONT 5 ÎÎ ÎÎ ÎÎ ÎÎ ÎÎ ÎÎ ÎÎ Î Î Î RESET 4 R1 R S 1 Î Î Î Î Î Î 3 OUT 7 DISCH 1 GND Pin numbers shown are for the D, JG, P, PS, and PW packages. NOTE A: RESET can override TRIG, which can override THRES. Submit Documentation Feedback 3 NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN VCC Supply voltage (2) VI Input voltage IO Output current θJA Package thermal impedance (3) (4) θJC Package thermal impedance (5) (6) TJ Operating virtual junction temperature Tstg (1) (2) (3) (4) (5) (6) CONT, RESET, THRES, TRIG MAX UNIT 18 V VCC V ±225 mA D package 97 P package 85 PS package 95 PW package 149 FK package 5.61 JG package 14.5 °C/W °C/W 150 °C Case temperature for 60 s FK package 260 °C Lead temperature 1, 6 mm (1/16 in) from case for 60 s JG package 300 °C 150 °C Storage temperature range –65 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to GND. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Maximum power dissipation is a function of TJ(max), θJC, and TC. The maximum allowable power dissipation at any allowable case temperature is PD = (TJ(max) - TC)/θJC. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with MIL-STD-883. Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) VCC Supply voltage VI Input voltage IO Output current TA 4 Operating free-air temperature MIN MAX NA555, NE555, SA555 4.5 16 SE555 4.5 18 CONT, RESET, THRES, and TRIG V VCC V ±200 mA NA555 –40 105 NE555 0 70 SA555 –40 85 SE555 –55 125 Submit Documentation Feedback UNIT °C NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 Electrical Characteristics VCC = 5 V to 15 V, TA = 25°C (unless otherwise noted) PARAMETER THRES voltage level TEST CONDITIONS MIN TYP MAX MIN TYP MAX 9.4 10 10.6 8.8 10 11.2 VCC = 5 V 2.7 3.3 4 2.4 3.3 4.2 30 250 5 5.2 1.67 1.9 4.8 VCC = 15 V TA = –55°C to 125°C TRIG voltage level RESET current 3 1.45 VCC = 5 V RESET voltage level 5.6 1.1 1.67 2.2 0.9 0.7 1 0.5 2 0.7 1 0.3 1.1 RESET at VCC 0.1 0.4 0.1 0.4 RESET at 0 V –0.4 –1 –0.4 –1.5 20 100 20 100 10 10.4 9 10 11 2.6 3.3 4 0.1 0.25 0.4 0.75 2 2.5 9.6 VCC = 15 V TA = –55°C to 125°C 9.6 2.9 TA = –55°C to 125°C VCC = 15 V, IOL = 50 mA VCC = 15 V, IOL = 100 mA VCC = 5 V, IOL = 3.5 mA 0.1 0.15 V TA = –55°C to 125°C TA = –55°C to 125°C 0.5 2.2 2.7 mA nA V V 2.5 2.5 0.35 0.2 0.1 0.35 0.15 0.4 0.8 0.15 13 0.25 13.3 12.75 13.3 12 VCC = 15 V, IOH = –200 mA 12.5 3 TA = –55°C to 125°C V 1 2 TA = –55°C to 125°C µA 0.2 0.4 0.1 VCC = 15 V, IOL = –100 mA nA 3.8 TA = –55°C to 125°C VCC = 15 V, IOL = –100 mA Output high, No load 3.8 TA = –55°C to 125°C VCC = 5 V, IOL = 8 mA Supply current 3.3 TA = –55°C to 125°C VCC = 5 V, IOL = 5 mA Output low, No load 10.4 2.9 VCC = 15 V, IOL = 200 mA (1) 0.5 TA = –55°C to 125°C VCC = 15 V, IOL = 10 mA High-level output voltage 250 5 V 1.9 0.3 VCC = 5 V Low-level output voltage 30 4.5 6 TA = –55°C to 125°C TRIG at 0 V DISCH switch off-state current CONT voltage (open circuit) UNIT VCC = 15 V THRES current (1) TRIG current NA555 NE555 SA555 SE555 12.5 3.3 2.75 V 3.3 2 VCC = 15 V 10 12 10 15 VCC = 5 V 3 5 3 6 VCC = 15 V 9 10 9 13 VCC = 5 V 2 4 2 5 mA This parameter influences the maximum value of the timing resistors RA and RB in the circuit of Figure 12. For example, when VCC = 5 V, the maximum value is R = RA + RB ≈ 3.4 MΩ, and for VCC = 15 V, the maximum value is 10 MΩ. Submit Documentation Feedback 5 NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 Operating Characteristics VCC = 5 V to 15 V, TA = 25°C (unless otherwise noted) PARAMETER MIN Initial error of timing interval (2) Each timer, monostable (3) Temperature coefficient of timing interval Each timer, monostable (3) TYP MAX 0.5 1.5 (4) 1.5 TA = MIN to MAX astable (5) 30 TA = 25°C 0.05 MIN UNIT TYP MAX 1 3 2.25 100 (4) 90 (3) Supply-voltage sensitivity of Each timer, monostable timing interval Each timer, astable (5) 50 ppm/ °C 150 0.2 (4) 0.15 0.1 % 0.5 0.3 %/V Output-pulse rise time CL = 15 pF, TA = 25°C 100 200 (4) 100 300 ns Output-pulse fall time CL = 15 pF, TA = 25°C 100 200 (4) 100 300 ns (1) (2) (3) (4) (5) 6 TA = 25°C Each timer, astable (5) Each timer, NA555 NE555 SA555 SE555 TEST CONDITIONS (1) For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. Timing interval error is defined as the difference between the measured value and the average value of a random sample from each process run. Values specified are for a device in a monostable circuit similar to Figure 9, with the following component values: RA = 2 kΩ to 100 kΩ, C = 0.1 µF. On products compliant to MIL-PRF-38535, this parameter is not production tested. Values specified are for a device in an astable circuit similar to Figure 12, with the following component values: RA = 1 kΩ to 100 kΩ, C = 0.1 µF. Submit Documentation Feedback NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 TYPICAL CHARACTERISTICS Data for temperatures below 0°C and above 70°C are applicable for SE555 circuits only. ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 4 2 1 0.7 0.4 10 7 VCC = 5 V ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ TA = −55°C TA = 25°C TA = 125°C 0.2 0.1 0.07 0.04 VOL − Low-Level Output Voltage − V VOL − Low-Level Output Voltage − V 10 7 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 0.02 VCC = 10 V 4 2 TA = 25°C 1 0.7 TA= −55°C TA = 125°C 0.4 0.2 0.1 0.07 0.04 0.02 0.01 0.01 1 2 4 7 10 20 40 70 100 1 IOL − Low-Level Output Current − mA 2 4 Figure 1. ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ 2.0 VCC = 15 V TA = −55°C 1 0.7 TA = 25°C 0.2 TA = 125°C 0.1 0.07 0.04 1.6 1.4 1.2 1 0.8 0.6 0.4 0.02 0.2 0.01 1 2 4 40 70 100 ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ TA = −55°C 1.8 2 0.4 20 DROP BETWEEN SUPPLY VOLTAGE AND OUTPUT vs HIGH-LEVEL OUTPUT CURRENT ( VCC − VOH) − Voltage Drop − V VOL − Low-Level Output Voltage − V 4 10 Figure 2. LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 10 7 7 IOL − Low-Level Output Current − mA 7 10 20 40 IOL − Low-Level Output Current − mA 70 100 0 TA = 25°C TA = 125°C VCC = 5 V to 15 V 1 Figure 3. 2 4 7 10 20 40 70 100 IOH − High-Level Output Current − mA Figure 4. Submit Documentation Feedback 7 NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 TYPICAL CHARACTERISTICS (continued) Data for temperatures below 0°C and above 70°C are applicable for SE555 circuits only. SUPPLY CURRENT vs SUPPLY VOLTAGE NORMALIZED OUTPUT PULSE DURATION (MONOSTABLE OPERATION) vs SUPPLY VOLTAGE 10 Pulse Duration Relative to Value at VCC = 10 V Output Low, No Load 9 I CC − Supply Current − mA 8 TA = 25°C 7 6 5 TA = −55°C 4 TA = 125°C 3 2 1 0 5 6 7 8 9 10 11 12 13 14 15 1.015 1.010 1.005 1 0.995 0.990 0.985 0 VCC − Supply Voltage − V 5 10 15 20 VCC − Supply Voltage − V Figure 5. Figure 6. NORMALIZED OUTPUT PULSE DURATION (MONOSTABLE OPERATION) vs FREE-AIR TEMPERATURE PROPAGATION DELAY TIME vs LOWEST VOLTAGE LEVEL OF TRIGGER PULSE 300 VCC = 10 V tPD − Propagation Delay Time − ns Pulse Duration Relative to Value at TA = 255C 1.015 1.010 1.005 1 0.995 0.990 250 TA = −55°C 200 TA = 0°C 150 100 TA = 25°C TA = 70°C 50 TA = 125°C 0.985 −75 0 −50 −25 0 25 50 100 125 75 0 TA − Free-Air Temperature − °C Figure 7. 8 0.1 x VCC 0.2 x VCC Figure 8. Submit Documentation Feedback 0.3 x VCC Lowest Voltage Level of Trigger Pulse 0.4 x VCC NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION Monostable Operation For monostable operation, any of these timers can be connected as shown in Figure 9. If the output is low, application of a negative-going pulse to the trigger (TRIG) sets the flip-flop (Q goes low), drives the output high, and turns off Q1. Capacitor C then is charged through RA until the voltage across the capacitor reaches the threshold voltage of the threshold (THRES) input. If TRIG has returned to a high level, the output of the threshold comparator resets the flip-flop (Q goes high), drives the output low, and discharges C through Q1. VCC (5 V to 15 V) RA Î Î Î 4 7 6 Input 2 5 8 CONT VCC RL RESET DISCH OUT 3 Output THRES TRIG GND 1 Pin numbers shown are for the D, JG, P, PS, and PW packages. Figure 9. Circuit for Monostable Operation Monostable operation is initiated when TRIG voltage falls below the trigger threshold. Once initiated, the sequence ends only if TRIG is high at the end of the timing interval. Because of the threshold level and saturation voltage of Q1, the output pulse duration is approximately tw = 1.1RAC. Figure 11 is a plot of the time constant for various values of RA and C. The threshold levels and charge rates both are directly proportional to the supply voltage, VCC. The timing interval is, therefore, independent of the supply voltage, so long as the supply voltage is constant during the time interval. Applying a negative-going trigger pulse simultaneously to RESET and TRIG during the timing interval discharges C and reinitiates the cycle, commencing on the positive edge of the reset pulse. The output is held low as long as the reset pulse is low. To prevent false triggering, when RESET is not used, it should be connected to VCC. Submit Documentation Feedback 9 NA555, NE555, SA555, SE555 PRECISION TIMERS ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) 10 RA = 9.1 kΩ CL = 0.01 µF RL = 1 kΩ See Figure 9 RA = 10 MΩ tw − Output Pulse Duration − s 1 Voltage − 2 V/div Input Voltage ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ Output Voltage RA = 1 MΩ 10−1 10−2 10−3 RA = 100 kΩ RA = 10 kΩ 10−4 RA = 1 kΩ 10−5 0.001 Capacitor Voltage 0.01 0.1 1 10 100 C − Capacitance − µF Time − 0.1 ms/div Figure 10. Typical Monostable Waveforms Figure 11. Output Pulse Duration vs Capacitance Astable Operation As shown in Figure 12, adding a second resistor, RB, to the circuit of Figure 9 and connecting the trigger input to the threshold input causes the timer to self-trigger and run as a multivibrator. The capacitor C charges through RA and RB and then discharges through RB only. Therefore, the duty cycle is controlled by the values of RA and RB. This astable connection results in capacitor C charging and discharging between the threshold-voltage level (≈0.67 × VCC) and the trigger-voltage level (≈0.33 × VCC). As in the monostable circuit, charge and discharge times (and, therefore, the frequency and duty cycle) are independent of the supply voltage. ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ VCC (5 V to 15 V) Î Î Î 0.01 µF Open (see Note A) 5 8 VCC CONT 4 7 RB 6 2 RL RESET DISCH 3 OUT Output THRES t H TRIG tL GND C Output Voltage 1 Pin numbers shown are for the D, JG, P, PS, and PW packages. NOTE A: Decoupling CONT voltage to ground with a capacitor can improve operation. This should be evaluated for individual applications. Figure 12. Circuit for Astable Operation 10 RL = 1 kW See Figure 12 Voltage − 1 V/div RA RA = 5 kW RB = 3 kW C = 0.15 µF Submit Documentation Feedback Capacitor Voltage Time − 0.5 ms/div Figure 13. Typical Astable Waveforms NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) Figure 13 shows typical waveforms generated during astable operation. The output high-level duration tH and low-level duration tL can be calculated as follows: + 0.693 (R ) R C A B) t + 0.693 (R C L B) 100 k H RA + 2 RB = 1 kΩ RA + 2 RB = 10 kΩ Other useful relationships are shown below. period + t ) t + 0.693 (R ) 2R ) C H L A B 1.44 frequency [ (R ) 2R ) C A B t Output driver duty cycle + R L B + t )t R ) 2R H L A B Output waveform duty cycle t R H + 1– B + t )t R ) 2R H L A B t R B Low-to-high ratio + L + t R ) R H A B f − Free-Running Frequency − Hz t 10 k RA + 2 RB = 100 kΩ 1k 100 10 1 RA + 2 RB = 1 MΩ RA + 2 RB = 10 MΩ 0.1 0.001 0.01 0.1 1 10 100 C − Capacitance − µF Figure 14. Free-Running Frequency Missing-Pulse Detector The circuit shown in Figure 15 can be used to detect a missing pulse or abnormally long spacing between consecutive pulses in a train of pulses. The timing interval of the monostable circuit is retriggered continuously by the input pulse train as long as the pulse spacing is less than the timing interval. A longer pulse spacing, missing pulse, or terminated pulse train permits the timing interval to be completed, thereby generating an output pulse as shown in Figure 16. 4 RESET Input 2 8 VCC OUT 0.01 µF 3 TRIG DISCH 5 RL CONT THRES GND 1 7 6 VCC = 5 V RA = 1 kΩ C = 0.1 µF See Figure 15 RA Output Voltage − 2 V/div VCC (5 V to 15 V) ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ Input Voltage Output Voltage C A5T3644 Capacitor Voltage Time − 0.1 ms/div Pin numbers shown are shown for the D, JG, P, PS, and PW packages. Figure 15. Circuit for Missing-Pulse Detector Figure 16. Completed Timing Waveforms for Missing-Pulse Detector Submit Documentation Feedback 11 NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) Frequency Divider By adjusting the length of the timing cycle, the basic circuit of Figure 9 can be made to operate as a frequency divider. Figure 17 shows a divide-by-three circuit that makes use of the fact that retriggering cannot occur during the timing cycle. ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ Voltage − 2 V/div VCC = 5 V RA = 1250 Ω C = 0.02 µF See Figure 9 Input Voltage Output Voltage Capacitor Voltage Time − 0.1 ms/div Figure 17. Divide-by-Three Circuit Waveforms 12 Submit Documentation Feedback NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) Pulse-Width Modulation The operation of the timer can be modified by modulating the internal threshold and trigger voltages, which is accomplished by applying an external voltage (or current) to CONT. Figure 18 shows a circuit for pulse-width modulation. A continuous input pulse train triggers the monostable circuit, and a control signal modulates the threshold voltage. Figure 19 shows the resulting output pulse-width modulation. While a sine-wave modulation signal is shown, any wave shape could be used. ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏÏÏ ÏÏÏÏÏÏ VCC (5 V to 15 V) RESET Clock Input 2 RL 8 VCC OUT TRIG RA Modulation Input Voltage 3 Output Voltage − 2 V/div 4 RA = 3 kΩ C = 0.02 µF RL = 1 kΩ See Figure 18 7 DISCH Modulation 5 Input (see Note A) CONT THRES 6 GND 1 Clock Input Voltage C Output Voltage Pin numbers shown are for the D, JG, P, PS, and PW packages. NOTE A: The modulating signal can be direct or capacitively coupled to CONT. For direct coupling, the effects of modulation source voltage and impedance on the bias of the timer should be considered. Figure 18. Circuit for Pulse-Width Modulation Capacitor Voltage Time − 0.5 ms/div Figure 19. Pulse-Width-Modulation Waveforms Submit Documentation Feedback 13 NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) Pulse-Position Modulation As shown in Figure 20, any of these timers can be used as a pulse-position modulator. This application modulates the threshold voltage and, thereby, the time delay, of a free-running oscillator. Figure 21 shows a triangular-wave modulation signal for such a circuit; however, any wave shape could be used. RA = 3 kΩ RB = 500 Ω RL = 1 kΩ See Figure 20 VCC (5 V to 15 V) 8 RESET 2 VCC OUT RA 3 Output TRIG DISCH Modulation Input 5 (see Note A) RL CONT THRES 7 6 RB GND Modulation Input Voltage Output Voltage C Pin numbers shown are for the D, JG, P, PS, and PW packages. NOTE A: The modulating signal can be direct or capacitively coupled to CONT. For direct coupling, the effects of modulation source voltage and impedance on the bias of the timer should be considered. Figure 20. Circuit for Pulse-Position Modulation 14 Voltage − 2 V/div 4 ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎ Capacitor Voltage Time − 0.1 ms/div Figure 21. Pulse-Position-Modulation Waveforms Submit Documentation Feedback NA555, NE555, SA555, SE555 PRECISION TIMERS www.ti.com SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006 APPLICATION INFORMATION (continued) Sequential Timer Many applications, such as computers, require signals for initializing conditions during start-up. Other applications, such as test equipment, require activation of test signals in sequence. These timing circuits can be connected to provide such sequential control. The timers can be used in various combinations of astable or monostable circuit connections, with or without modulation, for extremely flexible waveform control. Figure 22 shows a sequencer circuit with possible applications in many systems, and Figure 23 shows the output waveforms. VCC 4 RESET 2 8 VCC 3 OUT TRIG S DISCH 5 0.01 µF CONT 4 RESET RA 33 kΩ 2 TRIG 0.001 µF 7 1 CA = 10 µF RA = 100 kΩ CONT 6 0.01 µF CA RB Output A THRES GND 1 CB 4 RESET 33 kΩ 2 0.001 µF DISCH 7 5 THRES GND 8 VCC 3 OUT DISCH 5 6 0.01 µF Output B CB = 4.7 µF RB = 100 kΩ TRIG 8 VCC 3 OUT CONT THRES GND 1 CC CC = 14.7 µF RC = 100 kΩ RC 7 6 Output C Pin numbers shown are for the D, JG, P, PS, and PW packages. NOTE A: S closes momentarily at t = 0. ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏ ÏÏÏ ÏÏÏÏ ÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ Figure 22. Sequential Timer Circuit See Figure 22 Voltage − 5 V/div Output A Output B Output C twA ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏÏÏ ÏÏ ÏÏÏÏÏ ÏÏ ÏÏ ÏÏÏÏÏ ÏÏÏÏÏ ÏÏÏ ÏÏÏ ÏÏÏ ÏÏÏ twA = 1.1 RACA twB twB = 1.1 RBCB twC twC = 1.1 RCCC t=0 t − Time − 1 s/div Figure 23. Sequential Timer Waveforms Submit Documentation Feedback 15 PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) JM38510/10901BPA NA555D Pins Package Eco Plan (2) Qty Package Drawing ACTIVE CDIP JG 8 1 TBD A42 SNPB ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NA555DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NA555DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NA555DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NA555P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type NA555PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type NE555D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555DE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555DRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type NE555PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type NE555PSLE OBSOLETE SO PS 8 NE555PSR ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PSRE4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PW ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PWE4 ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PWG4 ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PWRE4 ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555PWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NE555Y OBSOLETE TBD 0 Addendum-Page 1 TBD Lead/Ball Finish MSL Peak Temp (3) Package Type Call TI Call TI N / A for Pkg Type Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SA555D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555DE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555DRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SA555P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SA555PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) SE555D ACTIVE SOIC D 8 75 TBD CU NIPDAU Level-1-220C-UNLIM SE555DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SE555DR ACTIVE SOIC D 8 2500 TBD CU NIPDAU Level-1-220C-UNLIM SE555DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SE555FKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type SE555JG ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type SE555JGB ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type SE555N OBSOLETE PDIP N 8 TBD Call TI SE555P ACTIVE PDIP P 8 Pb-Free (RoHS) CU NIPDAU 50 Call TI N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant NA555DR D 8 SITE 27 330 12 6.4 5.2 2.1 8 12 Q1 NA555DR D 8 SITE 41 330 12 6.4 5.2 2.1 8 12 Q1 NE555DR D 8 SITE 27 330 12 6.4 5.2 2.1 8 12 Q1 NE555DR D 8 SITE 41 330 12 6.4 5.2 2.1 8 12 Q1 NE555PSR PS 8 SITE 41 330 16 8.2 6.6 2.5 12 16 Q1 NE555PWR PW 8 SITE 41 330 12 7.0 3.6 1.6 8 12 Q1 SA555DR D 8 SITE 27 330 12 6.4 5.2 2.1 8 12 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 Device Package Pins Site Length (mm) Width (mm) Height (mm) NA555DR D 8 SITE 27 342.9 336.6 20.64 NA555DR D 8 SITE 41 346.0 346.0 29.0 NE555DR D 8 SITE 27 342.9 336.6 20.64 NE555DR D 8 SITE 41 346.0 346.0 29.0 NE555PSR PS 8 SITE 41 346.0 346.0 33.0 NE555PWR PW 8 SITE 41 346.0 346.0 29.0 SA555DR D 8 SITE 27 342.9 336.6 20.64 Pack Materials-Page 2 MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MLCC006B – OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated