ES1A THRU ES1J 1.0 AMP. Super Fast Surface Mount Rectifiers Voltage Range 50 to 600 Volts Current 1.0 Ampere SMA/DO-214AC Features Glass passivated junction chip For surface mounted application Low profile package Built-in strain relief, Ideal for automated placement Easy pick and place Superfast recovery time for high efficiency Glass passivated chip junction High temperature soldering: 260OC/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-O .062(1.58) .050(1.27) .111(2.83) .090(2.29) .187(4.75) .160(4.06) .103(2.61) .078(1.99) .012(.31) .006(.15) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per E1A STD RS-481 Weight: 0.064 gram .008(.20) .004(.10) .056(1.41) .035(0.90) .210(5.33) .195(4.95) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol ES ES ES ES ES ES ES ES Units Type Number 1A 1B 1C 1D 1F 1G 1H 1J Maximum Recurrent Peak Reverse Voltage V VRRM 50 100 150 200 300 400 500 600 Maximum RMS Voltage V VRMS 35 70 105 140 210 280 350 420 Maximum DC Blocking Voltage 50 100 150 200 300 400 500 600 V VDC Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA =25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) I(AV) 1.0 A IFSM 30 A 0.95 VF 1.3 1.7 5.0 100 35 IR Trr Cj 10 Operating Temperature Range RθJA RθJL TJ Storage Temperature Range TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. P.C.B. Mounted on 0.2 x 0.2”(5 x 5mm) Copper Pad Area. - 166 - 8 85 35 -55 to +150 -55 to + 150 V uA uA nS pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (ES1A THRU ES1J) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 1.2 1.0 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 0.8 0.6 0.4 0.2 30 8.3ms Single Half Sine Wave o (JEDEC Method) at TL=120 C 25 20 15 10 5.0 0 80 90 100 110 120 130 140 100 10 1 150 o LEAD TEMPERATURE. ( C) NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4- TYPICAL REVERSE CHARACTERISTICS 1000 50 INSTANTANEOUS REVERSE CURRENT. ( A) G 1A -D 10 ES 1F -1 ES 1H -1 J 1 ES INSTANTANEOUS FORWARD CURRENT. (A) 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.1 Tj=125 0C 10 Tj=85 0C 1 Tj=25 0C 0.1 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 FIG.5- TYPICAL JUNCTION CAPACITANCE 14 Tj=25 0C f=1.0MHz Vsig=50mVp-p 12 ES1 10 ES 8.0 1F A- D -J 6.0 4.0 2.0 0 0 1 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FORWARD VOLTAGE. (V) JUNCTION CAPACITANCE.(pF) 100 10 100 REVERSE VOLTAGE. (V) - 167 - 140