AWT6132R 415 MHz CDMA 3.4V/29.5dBm Linear Power Amplifier Module Data Sheet - Rev 2.1 FEATURES • InGaP HBT Technology • High Efficiency 35 % CDMA • Low Leakage Current (<5 µA) • SMT Module Package • 50 Ω Input and Output Matching • Shut Down and Mode Control • CDMA 2000 1XRTT Compliant • RoHS Compliant Package, 250 oC MSL-3 AW T 613 2R APPLICATIONS • CDMA/EVDO 415 MHz Wireless Handsets and Data Devices M5 Package 7 Pin 6 mm x 6 mm x 1.5 mm Surface Mount Module PRODUCT DESCRIPTION The AWT6132R is a high power, high efficiency amplifier module for CDMA wireless handset applications. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability and ruggedness. A low power mode is available to reduce power drain on the system battery. The 6 mm x 6 mm x 1.5 mm laminate package is self contained, incorporating 50 Ω input and output matching networks optimized for output power, linearity, and efficiency. Figure 1: Block Diagram 10/2008 AWT6132R GND VCC 1 7 GND RFIN 2 6 RFOUT VREF 3 5 VCC 4 VMODE Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VCC Supply Voltage 2 RFIN RF Input Signal 3 VREF Reference Voltage 4 VMODE Mode Control 5 VCC Supply Voltage 6 RFOUT RF Output 7 GND Ground MASTER DATA SHEET - Rev 2.1 10/2008 AWT6132R ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC ) 0 +5 V Mode Control Voltage (VMODE) 0 +3.4 V Reference Voltage (VREF) 0 +3.4 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 410 - 420 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.80 0 +2.90 - +3.1 +0.5 V PA"on" PA"shut down" Mode Control Voltage (VMODE) +2.5 0 +2.90 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) +29.0 (1) +29.5 - dBm Case Temperature (TC) -30 - +90 o COMMENTS CDMA, VCC =+3.4V C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at Vcc = +3.2 V , POUT is derated by 0.5 dB. MASTER DATA SHEET - Rev 2.1 10/2008 3 AWT6132R Table 4: Electrical Specifications – CDMA Operation (TC = +25 OC, VCC = +3.4 V, VREF = +2.90 V, 50 Ω system) TYP MAX UNIT 26 25 28 27 31 29 dB Gain Variation - 0.4 1.0 dB Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -52 -57 -46.5 -47 dB POUT = +29.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.90 V Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -62 -67 -59 -59 dB POUT = +29.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.90 V 33 6 35 7 - % POUT = +29.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.90 V Quiescent Current (Icq) - 60 80 mA through VCC pins, VMODE = +2.90 V Reference Current - 6.5 9 mA through VREF pin, PA "on" Mode Control Current - 0.8 1.0 mA through VMODE pin, VMODE = +2.90 V Leakage Current - <1 5 A VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -132 -130 dBm/Hz Harmonics 2fo 3fo, 4fo - -36 -45 -30 -35 dBc Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure POUT = +29.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.90 V fO +10 MHz, POUT < +29.5 dBm POUT < +29.5 dBm - - -70 dBc POUT < +29.5 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating ranges 10:1 - - VSWR Applies over all operating ranges Notes: (1) POUT is derated by 0.5 dB for IS-98 / CDMA 2000 operation. (2) ACPR and Efficiency Measured at 415 MHz. 4 COMMENTS MIN PARAMETER MASTER DATA SHEET - Rev 2.1 10/2008 AWT6132R APPLICATION INFORMATION High Bias Mode The power amplifier may be placed in a high bias mode by applying a logic low level (see Operating Ranges table) to the VMODE voltage. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. GND at slug (pad) VCC 1 7 GND 4.7uF (ceramic) RF Input RF Out (50 Ohms) (50 Ohms) 2 6 Bias Control VREF 3 4 VCC 5 0.1uF 4.7uF (ceramic) VMODE Figure 3: Application Circuit Schematic MASTER DATA SHEET - Rev 2.1 10/2008 5 AWT6132R PACKAGE OUTLINE Figure 4: M5 Package Outline - 7 Pin 6 x 6 x 1.5 mm Surface Mount Module (Low Band ) Figure 5: Branding Specification 6 MASTER DATA SHEET - Rev 2.1 10/2008 AWT6132R COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 5: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 6 mm x 6 mm x 1.5 mm 12 mm 8 mm 2500 13" MASTER DATA SHEET - Rev 2.1 10/2008 7 AWT6132R Ordering Information ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWT6132RM5P8 -30 oC to +90 oC RoHS Compliant 7 Pin 6 mm x 6 mm x 1.5 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel AWT6132RM5P9 -30 oC to +90 oC RoHS Compliant 7 Pin 6 mm x 6 mm x 1.5 mm Surface Mount Module Partial Tape and Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 MASTER DATA SHEET - Rev 2.1 10/2008