LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 LM2852 2A 500/1500kHz Synchronous SIMPLE SWITCHER® Buck Regulator Check for Samples: LM2852 FEATURES DESCRIPTION • • The LM2852 SIMPLE SWITCHER® synchronous buck regulator is a high frequency step-down switching voltage regulator capable of driving up to a 2A load with excellent line and load regulation. The LM2852 can accept an input voltage between 2.85V and 5.5V and deliver an output voltage that is factory programmable from 0.8V to 3.3V in 100mV increments. The LM2852 is available with a choice of two switching frequencies - 500kHz (LM2852Y) or 1.5MHz (LM2852X). It also features internal, typethree compensation to deliver a low component count solution. The exposed-pad HTSSOP-14 package enhances the thermal performance of the LM2852. 1 2 • • • • • • • Input Voltage Range of 2.85 to 5.5V Factory EEPROM Set Output Voltages from 0.8V to 3.3V in 100mV Increments Maximum Load Current of 2A Voltage Mode Control Internal Type-Three Compensation Switching Frequency of 500kHz or 1.5MHz Low Standby Current of 10µA Internal 60 mΩ MOSFET Switches Standard Voltage Options 0.8/1.0/1.2/1.5/1.8/2.5/3.3 Volts APPLICATIONS • • • • Low Voltage Point of Load Regulation Local Solution for FPGA/DSP/ASIC Core Power Broadband Networking and Communications Infrastructure Portable Computing Typical Application Circuit VIN = 3.3V PVIN CIN = 22 PF AVIN EN SS LM2852Y SNS VOUT = 2.5V ILOAD = 0A to 2A SW SGND PGND LO = 10 PH + CO = 100 PF CSS = 2.7 nF 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2006, Texas Instruments Incorporated LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com Figure 1. Efficiency vs ILOAD 96 PVIN = 3.3V EFFICIENCY (%) 94 92 90 88 86 84 0.1 1.0 10 ILOAD (A) Connection Diagram AVIN 1 14 SNS EN 2 13 NC SGND 3 12 NC 11 PGND LM2852 SS 4 NC 5 10 PGND PVIN 6 9 SW PVIN 7 8 SW Figure 2. 14-Pin HTSSOP – Top View See Package Number PWP0014A PIN DESCRIPTIONS AVIN (Pin 1): Chip bias input pin. This provides power to the logic of the chip. Connect to the input voltage or a separate rail. EN (Pin 2): Enable. Connect this pin to ground to disable the chip; connect to AVIN or leave floating to enable the chip; enable is internally pulled up. SGND (Pin 3): Signal ground. SS (Pin 4): Soft-start pin. Connect this pin to a small capacitor to control startup. The soft-start capacitance range is restricted to values 1 nF to 50 nF. NC (Pins 5, 12 and 13): No connect. These pins must be tied to ground or left floating in the application. PVIN (Pins 6, 7): Input supply pin. PVIN is connected to the input voltage. This rail connects to the source of the internal power PFET. SW (Pins 8, 9): Switch pin. Connect to the output inductor. PGND (Pins 10, 11): Power ground. Connect this to an internal ground plane or other large ground plane. SNS (Pin 14): Output voltage sense pin. Connect this pin to the output voltage as close to the load as possible. Exposed Pad: Connect to ground. 2 Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) −0.3V to 6.5V PVIN, AVIN, EN, SNS ESD Susceptibility (3) 2kV Power Dissipation Internally Limited Storage Temperature Range −65°C to +150°C Maximum Junction Temp. 14-Pin Exposed Pad HTSSOP Package 150°C Infrared (15 sec) 220°C Vapor Phase (60 sec) 215°C Soldering (10 sec) (1) (2) (3) 260°C Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for which the device is intended to be functional, but does not guarantee specfic performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Human body model: 1.5kΩ in series with 100pF. SW and PVIN pins are derated to 1.5kV Operating Ratings PVIN to GND 1.5V to 5.5V AVIN to GND 2.85V to 5.5V −40°C to +125°C Junction Temperature θJA 38°C/W Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 3 LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com Electrical Characteristics AVIN = PVIN = 5V unless otherwise indicated under the Conditions column. Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Symbol Parameter Conditions Min Typ Max Units SYSTEM PARAMETERS VOUT Voltage Tolerance (1) ΔVOUT/ΔAVIN Line Regulation (1) VOUT = 0.8V option 0.782 0.818 VOUT = 1.0V option 0.9775 1.0225 VOUT = 1.2V option 1.1730 1.2270 VOUT = 1.5V option 1.4663 1.5337 VOUT = 1.8V option 1.7595 1.8405 VOUT = 2.5V option 2.4437 2.5563 VOUT = 3.0V option 2.9325 3.0675 VOUT = 3.3V option 3.2257 3.3743 V VOUT = 0.8V, 1.0V, 1.2V, 1.5V, 1.8V or 2.5V 2.85V ≤ AVIN ≤ 5.5V 0.2 0.6 % VOUT = 3.3V 3.5V ≤ AVIN ≤ 5.5V 0.2 0.6 % ΔVOUT/ΔIO Load Regulation Normal operation VON UVLO Threshold (AVIN) Rising Falling Hysteresis 8 85 mV/A 2.47 2.85 V 150 210 mV rDSON-P PFET On Resistance Isw = 2A 75 140 mΩ rDSON-N NFET On Resistance Isw = 2A 55 120 mΩ RSS Soft-start resistance ICL Peak Current Limit Threshold LM2852X 2.75 4 4.95 LM2852Y 2.25 3 3.65 Operating Current Non-switching 0.85 2 mA Shutdown Quiescent EN = 0V Current 10 25 µA RSNS Sense pin resistance 400 fosc LM2852X 1500kHz option. 1050 1500 1825 kHz LM2852Y 500kHz option. 325 500 625 kHz 100 % IQ ISD 400 kΩ A kΩ PWM Drange Duty Cycle Range 0 ENABLE CONTROL (2) VIH EN Pin Minimum High Input VIL EN Pin Maximum Low Input IEN EN Pin Pullup Current % of AVIN 75 25 EN = 0V % of AVIN 1.2 µA THERMAL CONTROLS (1) (2) 4 TSD TJ for Thermal Shutdown 165 °C TSD-HYS Hysteresis for Thermal Shutdown 10 °C VOUT measured in a non-switching, closed-loop configuration at the SNS pin. The enable pin is internally pulled up, so the LM2852 is automatically enabled unless an external enable voltage is applied. Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 LM2852Y Typical Performance Characteristics (500kHz) Efficiency vs ILoad VOUT = 1.5V Efficiency vs ILoad VOUT = 2.5V 92 96 PVIN = 3.3V PVIN = 3.3V 90 94 86 84 92 EFFICIENCY (%) EFFICIENCY (%) 88 PVIN = 5.0V 82 90 PVIN = 5.0V 88 80 86 78 84 76 0.1 1.0 0.1 10 1.0 10 ILOAD (A) ILOAD (A) Figure 3. Figure 4. Efficiency vs ILoad VOUT = 3.3V Frequency vs Temperature 95 560 94 550 VIN = 3.3V PVIN = 5.0V 540 FREQUENCY (kHz) EFFICIENCY (%) 93 92 91 90 530 520 510 89 500 88 490 87 0.1 1.0 10 480 -50 VIN = 5V -25 0 25 50 75 100 125 150 TEMPERATURE (oC) ILOAD (A) Figure 5. Figure 6. Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 5 LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com LM2852X Typical Performance Characteristics (1500kHz) Efficiency vs ILoad VOUT = 1.5V Efficiency vs ILoad VOUT = 2.5V 100 85 PVIN = 3.3V PVIN = 3.3V 80 90 70 65 60 80 EFFICIENCY (%) EFFICIENCY (%) 75 PVIN = 5.0V PVIN = 5.0V 70 60 55 50 50 45 0.1 1.0 40 0.1 10 ILOAD (A) Figure 7. Figure 8. Efficiency vs ILoad VOUT = 3.3V Frequency vs Temperature 1600 85 1550 FREQUENCY (kHz) EFFICIENCY (%) 80 PVIN = 5.0V 70 65 60 1500 1450 PVIN = 5.0V 1400 1350 1300 1.0 10 1200 -50 -25 0 25 50 75 80 85 90 o TEMPERATURE ( C) ILOAD (A) Figure 9. 6 PVIN = 3.3V 1250 55 50 0.1 10 ILOAD (A) 90 75 1.0 Figure 10. Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 LM2852 Typical Performance Characteristics (Both Y and X Versions) Shutdown Current vs VIN Quiescent Current (Non-Switching) vs VIN 1100 17 1000 15 125oC 900 13 o 85 C IQ (PA) IQ SHUTDOWN (PA) 125oC 11 o 800 85oC 25 C 25oC 700 9 -40oC 7 5 2.5 3 3.5 4 4.5 5 -40oC 600 500 2.5 5.5 3 3.5 4 4.5 5 5.5 VIN (V) VIN (V) Figure 11. Figure 12. NMOS Switch RDSON vs Temperature PMOS Switch RDSON vs Temperature 100 130 120 90 PFET RDSON (m:) NFET RDSON (m:) 110 80 PVIN = 3.3V 70 PVIN = 5.0V 60 PVIN = 3.3V 100 90 PVIN = 5.0V 80 70 50 60 40 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (oC) 50 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (oC) Figure 13. Figure 14. Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 7 LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com Block Diagram SGND PVIN Reference Oscillator UVLO DAC AVIN Current Limit Ramp and Clock Generator 400 k: EN Gate Drive Error Amp SS + 20 pF 200 k: 200 k: Zc1 Zc2 SW + PWM Comp PGND SNS 8 Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 APPLICATIONS INFORMATION The LM2852 is a DC-DC synchronous buck regulator belonging to Texas Instrument’s SIMPLE SWITCHER family. Integration of the PWM controller, power switches and compensation network greatly reduces the component count required to implement a switching power supply. A typical application requires only four components: an input capacitor, a soft-start capacitor, an output filter capacitor and an output filter inductor. INPUT CAPACITOR (CIN) Fast switching of large currents in the buck converter places a heavy demand on the voltage source supplying PVIN. The input capacitor, CIN, supplies extra charge when the switcher needs to draw a burst of current from the supply. The RMS current rating and the voltage rating of the CIN capacitor are therefore important in the selection of CIN. The RMS current specification can be approximated by: IRMS = ILOAD D(1-D) where • D is the duty cycle, VOUT/VIN. CIN also provides filtering of the supply. (1) Trace resistance and inductance degrade the benefits of the input capacitor, so CIN should be placed very close to PVIN in the layout. A 22 µF or 47 µF ceramic capacitor is typically sufficient for CIN. In parallel with the large input capacitance a smaller capacitor may be added such as a 1µF ceramic for higher frequency filtering. SOFT-START CAPACITOR (CSS) The DAC that sets the reference voltage of the error amp sources a current through a resistor to set the reference voltage. The reference voltage is one half of the output voltage of the switcher due to the 200kΩ divider connected to the SNS pin. Upon start-up, the output voltage of the switcher tracks the reference voltage with a two to one ratio as the DAC current charges the capacitance connected to the reference voltage node. Internal capacitance of 20pF is permanently attached to the reference voltage node which is also connected to the soft-start pin, SS. Adding a soft-start capacitor externally increases the time it takes for the output voltage to reach its final level. The charging time required for the reference voltage can be estimated using the RC time constant of the DAC resistor and the capacitance connected to the SS pin. Three RC time constant periods are needed for the reference voltage to reach 95% of its final value. The actual start-up time will vary with differences in the DAC resistance and higher-order effects. If little or no soft-start capacitance is connected, then the start-up time may be determined by the time required for the current limit current to charge the output filter capacitance. The capacitor charging equation I = C ΔV/Δt can be used to estimate the start-up time in this case. For example, a part with a 3V output, a 100 µF output capacitance and a 3A current limit threshold would require a time of 100 µs: 't = C 'V 3V = 100 PF = 100 Ps I 3A (2) Since it is undesirable for the power supply to start up in current limit, a soft-start capacitor must be chosen to force the LM2852 to start up in a more controlled fashion based on the charging of the soft-start capacitance. In this example, suppose a 3 ms start time is desired. Three time constants are required for charging the soft-start capacitor to 95% of the final reference voltage. So in this case RC=1ms. The DAC resistor, R, is 400 kΩ so C can be calculated to be 2.5nF. A 2.7nF ceramic capacitor can be chosen to yield approximately a 3ms start-up time. SOFT-START CAPACITOR (CSS) AND FAULT CONDITIONS Various fault conditions such as short circuit and UVLO of the LM2852 activate internal circuitry designed to control the voltage on the soft-start capacitor. For example, during a short circuit current limit event, the output voltage typically falls to a low voltage. During this time, the soft-start voltage is forced to track the output so that once the short is removed, the LM2852 can restart gracefully from whatever voltage the output reached during the short circuit event. The range of soft-start capacitors is therefore restricted to values 1nF to 50nF. Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 9 LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com COMPENSATION The LM2852 provides a highly integrated solution to power supply design. The compensation of the LM2852, which is type-three, is included on-chip. The benefit to integrated compensation is straightforward, simple power supply design. Since the output filter capacitor and inductor values impact the compensation of the control loop, the range of L, C and CESR values is restricted in order to ensure stability. OUTPUT FILTER VALUES Table 1 details the recommended inductor and capacitor ranges for the LM2852 that are suggested for various typical output voltages. Values slightly different than those recommended may be used, however the phase margin of the power supply may be degraded. Table 1. Output Filter Values Frequency Option LM2852Y (500kHz) LM2852X (1500kHz) 10 VOUT (V) PVIN (V) L (µH) C (µF) CESR (mΩ) Min Max Min Max Min Max 0.8 3.3 10 15 100 220 70 200 0.8 5.0 10 15 100 120 70 200 1.0 3.3 10 15 100 180 70 200 1.0 5.0 10 15 100 180 70 200 1.2 3.3 10 15 100 180 70 200 1.2 5.0 15 22 100 120 70 200 1.5 3.3 10 15 100 120 70 200 1.5 5.0 22 22 100 120 70 200 1.8 3.3 10 15 100 120 100 200 1.8 5.0 22 33 100 120 100 200 2.5 3.3 6.8 10 68 120 95 275 2.5 5.0 15 22 68 120 95 275 3.3 5.0 15 22 68 100 100 275 0.8 3.3 0.8 5.0 1.0 3.3 1.0 5.0 1.2 3.3 1.2 5.0 1.5 3.3 1.5 5.0 1.8 3.3 1.8 5.0 2.5 3.3 2.5 5.0 3.3 5.0 The 1500kHz version is designed for ceramic output capacitors which typically have very low ESR (<10mΩ.) 1 Submit Documentation Feedback 10 Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 CHOOSING AN INDUCTANCE VALUE The current ripple present in the output filter inductor is determined by the input voltage, output voltage, switching frequency and inductance according to the following equation: 'IL = D x (VIN - VOUT) fxL where • • • • • • ΔIL is the peak-to-peak current ripple. D is the duty cycle VOUT/VIN. VIN is the input voltage applied to the PVIN pin. VOUT is the output voltage of the switcher. f is the switching frequency. L is the inductance of the output filter inductor. (3) Knowing the current ripple is important for inductor selection since the peak current through the inductor is the load current plus one half the ripple current. Care must be taken to ensure the peak inductor current does not reach a level high enough to trip the current limit circuitry of the LM2852. As an example, consider a 5V to 1.2V conversion and a 500kHz switching frequency. According to Table 1, a 15µH inductor may be used. Calculating the expected peak-to-peak ripple, 'IL = 1.2V x (5V - 1.2V) 5V 500 kHz x 15 PH = 121.6 mA (4) The maximum inductor current for a 2A load would therefore be 2A plus 60.8 mA, 2.0608A. As shown in the ripple equation, the current ripple is inversely proportional to inductance. OUTPUT FILTER INDUCTORS Once the inductance value is chosen, the key parameter for selecting the output filter inductor is its saturation current (Isat) specification. Typically Isat is given by the manufacturer as the current at which the inductance of the coil falls to a certain percentage of the nominal inductance. The Isat of an inductor used in an application should be greater than the maximum expected inductor current to avoid saturation. Below is a table of inductors that may be suitable in LM2852 applications. Table 2. LM2852 Output Filter Inductors Inductance (µH) Part Number Vendor 1 DO1608C-102 Coilcraft 1 DO1813P-102HC Coilcraft 6.8 DO3316P-682 Coilcraft 7 MSS1038-702NBC Coilcraft 10 DO3316P-103 Coilcraft 10 MSS1038-103NBC Coilcraft 12 MSS1038-123NBC Coilcraft 15 D03316P-153 Coilcraft 15 MSS1038-153NBC Coilcraft 18 MSS1038-183NBC Coilcraft 22 DO3316P-223 Coilcraft 22 MSS1038-223NBC Coilcraft 22 DO3340P-223 Coilcraft 27 MSS1038-273NBC Coilcraft 33 MSS1038-333NBC Coilcraft 33 DO3340P-333 Coilcraft Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 11 LM2852 SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 www.ti.com OUTPUT FILTER CAPACITORS The capacitors that may be used in the output filter with the LM2852 are limited in value and ESR range according to Table 1. Below are some examples of capacitors that can typically be used in an LM2852 application. Table 3. LM2852 Output Filter Capacitors Capacitance (µF) Part Number Chemistry Vendor 10 GRM31MR61A106KE19 Ceramic Murata 10 GRM32DR61E106K Ceramic Murata 68 595D686X_010C2T Tantalum Vishay - Sprague 68 595D686X_016D2T Tantalum Vishay - Sprague 100 595D107X_6R3C2T Tantalum Vishay - Sprague 100 595D107X_016D2T Tantalum Vishay - Sprague 100 NOSC107M004R0150 Niobium Oxide AVX 100 NOSD107M006R0100 Niobium Oxide AVX 120 595D127X_004C2T Tantalum Vishay - Sprague 120 595D127X_010D2T Tantalum Vishay - Sprague 150 595D157X_004C2T Tantalum Vishay - Sprague 150 595D157X_016D2T Tantalum Vishay - Sprague 150 NOSC157M004R0150 Niobium Oxide AVX 150 NOSD157M006R0100 Niobium Oxide AVX 220 595D227X_004D2T Tantalum Vishay - Sprague 220 NOSD227M004R0100 Niobium Oxide AVX 220 NOSE227M006R0100 Niobium Oxide AVX SPLIT-RAIL OPERATION The LM2852 can be powered using two separate voltages for AVIN and PVIN. AVIN is the supply for the control logic; PVIN is the supply for the power FETs. The output filter components need to be chosen based on the value of PVIN. For PVIN levels lower than 3.3V, use output filter component values recommended for 3.3V. PVIN must always be equal to or less than AVIN. PVIN = 3.3V AVIN = 5V PVIN CIN = 47 PF 1 PF AVIN EN SS LM2852Y SNS VOUT = 1.5V ILOAD = 0A to 2A SW SGND PGND LO = 10 PH + CO = 100 PF CSS = 3.3 nF SWITCH NODE PROTECTION The LM2852 includes protection circuitry that monitors the voltage on the switch pin. Under certain conditions, switching is disabled in order to protect the switching devices. One result of the protection circuitry may be observed when power to the LM2852 is applied with no or light load on the output. The output regulates to the rated voltage, but no switching may be observed. As soon as the output is loaded, the LM2852 begins normal switching operation. LAYOUT HINTS These are several guidelines to follow while designing the PCB layout for an LM2852 application. 1. The input bulk capacitor, CIN, should be placed very close to the PVIN pin to keep the resistance as low as possible between the capacitor and the pin. High current levels will be present in this connection. 12 Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 LM2852 www.ti.com SNVS325C – JANUARY 2005 – REVISED OCTOBER 2006 2. All ground connections must be tied together. Use a broad ground plane, for example a completely filled back plane, to establish the lowest resistance possible between all ground connections. 3. The sense pin connection should be made as close to the load as possible so that the voltage at the load is the expected regulated value. The sense line should not run too close to nodes with high EMI (such as the switch node) to minimize interference. 4. The switch node connections should be low resistance to reduce power losses. Low resistance means the trace between the switch pin and the inductor should be wide. However, the area of the switch node should not be too large since EMI increases with greater area. So connect the inductor to the switch pin with a short, but wide trace. Other high current connections in the application such as PVIN and VOUT assume the same trade off between low resistance and EMI. 5. Allow area under the chip to solder the entire exposed die attach pad to ground for improved thermal and electrical performance. LM2852 Example Circuit Schematic VIN = 3.3V U1 PVIN Rf CINX AVIN EN Cf CIN SS LM2852 SNS VOUT = 1.8V ILOAD = 0A to 2A SW SGND PGND LO + CO CSS Figure 15. Table 4. Bill of Materials for 500kHz (LM2852Y) 3.3VIN to 1.8 VOUT Conversion ID Part Number U1 LM2852YMXA-1.8 Type Size 2A Buck HTSSOP-14 Inductor Parameters Qty Vendor 1 TI LO DO3316P-153 15 µH 1 Coilcraft CO* 595D107X_6R3C2T Capacitor Case Code “C” 100 µF ±20% 1 Vishay-Sprague CIN GRM32ER60J476ME20B Capacitor 1210 47µF/X5R/6.3V 1 Murata CINX GRM21BR71C105KA01B Capacitor 0805 1µF/X7R/16V 1 Murata CSS VJ0805Y272KXXA Capacitor 0805 2.7nF ±10% 1 Vishay-Vitramon Rf CRCW060310R0F Resistor 0603 10Ω ±10% 1 Vishay-Dale Cf GRM21BR71C105KA01B Capacitor 0805 1µF/X7R/16V 1 Murata Table 5. Bill of Materials for 1500kHz (LM2852X) 3.3V to 1.8V Conversion Type Size U1 ID LM2852XMXA-1.8 Part Number 2A Buck HTSSOP-14 L0 DO1813P-102HC Inductor Parameters Qty Vendor 1 TI 1 µH 1 Coilcraft C0 GRM32DR61E106K Capacitor 1210 10 µF/X5R/25V 1 Murata CIN GRM32ER60J476ME20B Capacitor 1210 47µF/X5R/6.3V 1 Murata CINX GRM21BR71C105KA01B Capacitor 0805 1µF/X7R/16V 1 Murata CSS VJ0805Y272KXXA Capacitor 0805 2.7nF ±10% 1 Vishay-Vitramon Rf CRCW060310R0F Resistor 0603 10Ω ±10% 1 Vishay-Dale Cf GRM21BR71C105KA01B Capacitor 0805 1µF/X7R/16V 1 Murata Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Links: LM2852 13 PACKAGE OPTION ADDENDUM www.ti.com 9-Mar-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM2852XMXA-0.8 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 0.8 LM2852XMXA-0.8/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 0.8 LM2852XMXA-1.0 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 1.0 LM2852XMXA-1.0/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.0 LM2852XMXA-1.2 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 1.2 LM2852XMXA-1.2/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.2 LM2852XMXA-1.5 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 1.5 LM2852XMXA-1.5/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.5 LM2852XMXA-1.8 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 1.8 LM2852XMXA-1.8/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.8 LM2852XMXA-2.5 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 2.5 LM2852XMXA-2.5/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 2.5 LM2852XMXA-3.0 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI 2852X 3.0 LM2852XMXA-3.0/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852X 3.0 LM2852XMXA-3.3 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852X 3.3 LM2852XMXA-3.3/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 3.3 LM2852XMXAX-0.8 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 0.8 Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 9-Mar-2013 Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM2852XMXAX-0.8/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 0.8 LM2852XMXAX-1.0 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 1.0 LM2852XMXAX-1.0/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.0 LM2852XMXAX-1.2 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 1.2 LM2852XMXAX-1.2/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.2 LM2852XMXAX-1.5 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 1.5 LM2852XMXAX-1.5/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.5 LM2852XMXAX-1.8 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 1.8 LM2852XMXAX-1.8/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 1.8 LM2852XMXAX-2.5 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 2.5 LM2852XMXAX-2.5/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 2.5 LM2852XMXAX-3.0 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI 2852X 3.0 LM2852XMXAX-3.0/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852X 3.0 LM2852XMXAX-3.3 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852X 3.3 LM2852XMXAX-3.3/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852X 3.3 LM2852YMXA-0.8 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -0.8 LM2852YMXA-0.8/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -0.8 LM2852YMXA-1.0 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -1.0 Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 9-Mar-2013 Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM2852YMXA-1.0/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.0 LM2852YMXA-1.2 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -1.2 LM2852YMXA-1.2/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.2 LM2852YMXA-1.3 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI 2852Y 1.3 LM2852YMXA-1.3/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852Y 1.3 LM2852YMXA-1.5 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -1.5 LM2852YMXA-1.5/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.5 LM2852YMXA-1.8 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -1.8 LM2852YMXA-1.8/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.8 LM2852YMXA-2.5 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -2.5 LM2852YMXA-2.5/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -2.5 LM2852YMXA-3.0 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI 2852Y 3.0 LM2852YMXA-3.0/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852Y 3.0 LM2852YMXA-3.3 ACTIVE HTSSOP PWP 14 94 TBD Call TI Call TI -40 to 125 2852Y -3.3 LM2852YMXA-3.3/NOPB ACTIVE HTSSOP PWP 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -3.3 LM2852YMXAX-0.8 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -0.8 LM2852YMXAX-0.8/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -0.8 LM2852YMXAX-1.0 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -1.0 Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 9-Mar-2013 Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM2852YMXAX-1.0/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.0 LM2852YMXAX-1.2 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -1.2 LM2852YMXAX-1.2/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.2 LM2852YMXAX-1.3 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI 2852Y 1.3 LM2852YMXAX-1.3/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852Y 1.3 LM2852YMXAX-1.5 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -1.5 LM2852YMXAX-1.5/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.5 LM2852YMXAX-1.8 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -1.8 LM2852YMXAX-1.8/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -1.8 LM2852YMXAX-2.5 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -2.5 LM2852YMXAX-2.5/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -2.5 LM2852YMXAX-3.0 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI 2852Y 3.0 LM2852YMXAX-3.0/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 2852Y 3.0 LM2852YMXAX-3.3 ACTIVE HTSSOP PWP 14 2500 TBD Call TI Call TI -40 to 125 2852Y -3.3 LM2852YMXAX-3.3/NOPB ACTIVE HTSSOP PWP 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2852Y -3.3 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com 9-Mar-2013 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Only one of markings shown within the brackets will appear on the physical device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 17-Nov-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ B0 (mm) K0 (mm) P1 (mm) HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852XMXAX-0.8/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 LM2852XMXAX-1.0/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 LM2852XMXAX-1.2/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP LM2852XMXAX-1.5/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP LM2852XMXAX-1.8/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852XMXAX-2.5/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852XMXAX-3.0/NOP HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852XMXAX-0.8 LM2852XMXAX-1.0 LM2852XMXAX-1.2 LM2852XMXAX-1.5 LM2852XMXAX-1.8 LM2852XMXAX-2.5 LM2852XMXAX-3.0 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 17-Nov-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) HTSSOP PWP 14 2500 330.0 12.4 LM2852XMXAX-3.3/NOP HTSSOP B PWP 14 2500 330.0 HTSSOP PWP 14 2500 LM2852YMXAX-0.8/NOP HTSSOP B PWP 14 HTSSOP PWP LM2852YMXAX-1.0/NOP HTSSOP B W Pin1 (mm) Quadrant 6.95 8.3 1.6 8.0 12.0 Q1 12.4 6.95 8.3 1.6 8.0 12.0 Q1 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-1.2/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-1.3/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-1.5/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-1.8/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-2.5/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-3.0/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 HTSSOP PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LM2852YMXAX-3.3/NOP HTSSOP B PWP 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 B LM2852XMXAX-3.3 LM2852YMXAX-0.8 LM2852YMXAX-1.0 LM2852YMXAX-1.2 LM2852YMXAX-1.3 LM2852YMXAX-1.5 LM2852YMXAX-1.8 LM2852YMXAX-2.5 LM2852YMXAX-3.0 LM2852YMXAX-3.3 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-Nov-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2852XMXAX-0.8 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-0.8/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.0 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.0/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.2 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.2/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.5 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.5/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.8 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-1.8/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-2.5 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-2.5/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-3.0 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-3.0/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-3.3 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852XMXAX-3.3/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-0.8 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-0.8/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.0 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.0/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 Pack Materials-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 17-Nov-2012 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2852YMXAX-1.2 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.2/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.3 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.3/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.5 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.5/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.8 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-1.8/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-2.5 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-2.5/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-3.0 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-3.0/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-3.3 HTSSOP PWP 14 2500 349.0 337.0 45.0 LM2852YMXAX-3.3/NOPB HTSSOP PWP 14 2500 349.0 337.0 45.0 Pack Materials-Page 4 MECHANICAL DATA PWP0014A MXA14A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM2852X-1.2EVAL LM2852X-1.8EVAL LM2852X-2.5EVAL LM2852X-3.3EVAL LM2852Y-1.2EVAL LM2852Y1.8EVAL LM2852Y-2.5EVAL LM2852Y-3.3EVAL