Vishay MKP1839HQ Ac and pulse metallized polypropylene film capacitors mkp axial type Datasheet

MKP 1839 HQ
Vishay Roederstein
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
FEATURES
Supplied loose in box, taped on ammopack or reel
available on request
• Compliant to RoHS directive 2002/95/EC
Ødt
lt
l
lt
d
ENCAPSULATION
Plastic-wrapped, epoxy resin sealed. Flame
retardant.
APPLICATIONS
High current and high pulse operations
CLIMATIC TESTING CLASS ACC. TO
IEC 60068-1
55/110/56
REFERENCE STANDARDS
CAPACITANCE RANGE (E12 SERIES)
IEC 60384-17
0.1 µF to 3.3 µF
MARKING
CAPACITANCE TOLERANCE
Manufacturer’s logo; code for dielectric material;
manufacturer’s
type
designation;
C-code;
rated
voltage-code; tolerance-code; special n °C-value; tolerance;
rated voltage; year and week; manufacturer’s location
±5%
LEADS
Tinned wire
DIELECTRIC
RATED TEMPERATURE
Polypropylene film
85 °C
ELECTRODES
MAXIMUM APPLICATION TEMPERATURE
Metallized
At 85 °C: UC = 1.0 UR
at 110 °C: UC = 0.7 UR
CONSTRUCTION
PULL TEST ON LEADS
Series construction
≥ 20 N in direction of leads according to IEC 60068-2-21
RATED (DC) VOLTAGE
630 V, 850 V, 1250 V, 1600 V
BENT TEST ON LEADS
2 bends trough 90° with half of the force used in pull test
RELIABILITY
RATED (AC) VOLTAGE
300 V, 400 V, 450 V, 600 V
Operation life > 300 000 h
Failure rate < 5 FIT (40 °C and 0.5 x UR)
DETAIL SPECIFICATION
For more detailed data and test requirements contact:
[email protected]
www.vishay.com
258
For technical questions, contact: [email protected]
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors Vishay Roederstein
MKP Axial Type
COMPOSITION OF CATALOG NUMBER
MULTIPLIER
(nF)
SPECIAL LETTER
FOR TAPED
CAPACITANCE
(numerically)
0.1
2
1
3
10
4
100
5
Bulk
Example:
468 = 680 nF
R
Reel
G
Ammopack
(1)
Special
HIGH QUALITY
CAPACITOR
TYPE
MKP 1839
X
XX
08
X
VOLTAGE (Vdc)
HQ
X
TOLERANCE
63 = 630 V
4
±5%
08 = 850 V
12 = 1250 V
13 = 1600 V
Note
(1) For detailed tape specifications refer to “Packaging Information”: www.vishay.com/doc?28139 or end of catalog
SPECIFIC REFERENCE DATA
DESCRIPTION
VALUE
Tangent of loss angle:
at 1 kHz
at 10 kHz
at 100 kHz
0.1 µF < C ≤ 0.47 µF
≤ 3 x 10-4
≤ 5 x 10-4
≤ 35 x 10-4
0.47 µF < C ≤ 1 µF
≤3x
≤8x
≤ 50 x 10-4
1 µF < C ≤ 3.3 µF
10-4
≤ 3 x 10-4
10-4
≤ 10 x 10-4
≤ 60 x 10-4
Rated voltage pulse slope
(dU/dt)R at URdc
630 VDC
850 VDC
1250 VDC
1600 VDC
500 V/µs
1000 V/µs
1000 V/µs
1000 V/µs
UP-P peak-to-peak voltage
700 V
1130 V
1400 V
1600 V
2000 V
2560 V
R between leads,
for C ≤ 0.33 µF at 500 V, 1 min
> 100 GΩ
RC between leads,
for C > 0.33 µF at 500 V, 1 min
> 30 000 s
R between interconnecting and
wrapped film at 500 V, 1 min
> 100 GΩ
Withstanding (DC) voltage (cut off
current 10 mA), rise time 100 V/s
Withstanding (DC) voltage between
leads and wrapped film
(1.4 x URac + 2000)
Maximum application temperature
Document Number: 28162
Revision: 21-Apr-10
1008 V
1360 V
1 min
2840 V, 1 min
110 °C
For technical questions, contact: [email protected]
www.vishay.com
259
MKP 1839 HQ
Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
VOLTAGE CODE 63
630 VDC/300 VAC
CAPACITANCE
DIMENSIONS
max.
(mm)
VOLTAGE CODE 08
850 VDC/400 VAC
MASS
dt
± 0.08 mm
SPQ (1)
DIMENSIONS
max.
(mm)
MASS
dt
± 0.08 mm
SPQ (1)
(µF)
D
L
(g)
(mm)
Pieces
D
L
(g)
(mm)
Pieces
0.1
7
26.5
0.9
0.8
2000
8.5
31.5
1.6
0.8
1500
0.15
8
26.5
1.2
0.8
1750
10
31.5
2.3
0.8
1000
0.18
8.5
26.5
1.4
0.8
1500
11
31.5
2.7
0.8
850
0.22
9.5
26.5
1.6
0.8
1250
11.5
31.5
3.2
0.8
750
0.27
10
26.5
1.9
0.8
1000
13
31.5
3.9
0.8
1000
0.33
11
26.5
2.3
0.8
900
14
31.5
4.6
0.8
1000
0.39
10.5
31.5
2.6
0.8
900
15
31.5
5.4
0.8
1000
0.47
11
31.5
3.0
0.8
750
16.5
31.5
6.5
0.8
1000
0.56
12
31.5
3.5
0.8
650
15
31.5
5.4
0.8
1000
0.68
13
31.5
4.2
0.8
500
16.5
31.5
6.5
0.8
1000
0.82
14
31.5
5.1
0.8
1000
18
31.5
7.8
1.0
750
1
16
31.5
6.1
0.8
900
19.5
31.5
9.4
1.0
600
1.5
19
31.5
9.0
1.0
600
24
31.5
13.9
1.0
400
2.2
23
31.5
13.1
1.0
450
-
-
-
-
-
3.3
28
31.5
19.5
1.0
300
-
-
-
-
-
MASS
dt
± 0.08 mm
SPQ (1)
(g)
(mm)
Pieces
VOLTAGE CODE 13
1600 VDC/600 VAC
VOLTAGE CODE 12
1250 VDC/450 VAC
CAPACITANCE
DIMENSIONS
max.
(mm)
L
MASS
dt
± 0.08 mm
SPQ (1)
DIMENSIONS
max.
(mm)
(g)
(mm)
Pieces
D
(µF)
D
L
0.1
8.5
31.5
1.6
0.8
1500
10.5
31.5
2.7
0.8
1000
0.15
10
31.5
2.3
0.8
1000
12.5
31.5
3.9
0.8
600
0.18
11
31.5
2.7
0.8
1000
13.5
31.5
4.6
0.8
500
0.22
11.5
31.5
3.2
0.8
800
15
31.5
5.5
0.8
500
0.27
13
31.5
3.9
0.8
650
16.5
31.5
6.7
0.8
900
0.33
14
31.5
4.6
0.8
500
18
31.5
8.1
1.0
750
0.39
15
31.5
5.4
0.8
1000
19.5
31.5
9.5
1.0
600
0.47
16.5
31.5
6.5
0.8
900
21.5
31.5
11.3
1.0
500
0.56
18
31.5
7.7
1.0
750
23.5
31.5
13.4
1.0
400
0.68
20
31.5
9.2
1.0
600
25.5
31.5
16.2
1.0
350
0.82
21.5
31.5
11.1
1.0
500
-
-
-
-
-
1
23.5
31.5
13.4
1.0
400
-
-
-
-
-
1.5
-
-
-
-
-
-
-
-
-
-
2.2
-
-
-
-
-
-
-
-
-
-
3.3
-
-
-
-
-
-
-
-
-
-
Note
(1)
SPQ = Standard Packing Quantity
www.vishay.com
260
For technical questions, contact: [email protected]
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors Vishay Roederstein
MKP Axial Type
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the capacitor body is in good contact with the printed-circuit
board.
• For L ≤ 19 mm capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped
• The maximum diameter and length of the capacitors are specified in the dimensions table
• Eccentricity as shown in the drawing below:
1 mm
Storage Temperature
• Storage temperature: Tstg = - 25 °C to + 40 °C with RH maximum 80 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23 °C ± 1 °C, an atmospheric pressure
of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %.
For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: [email protected]
www.vishay.com
261
MKP 1839 HQ
Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
CHARACTERISTICS
Capacitance as a function of ambient temperature (typical curve)
Tangent of loss angle as a function of frequency (typical curve)
103
Dissipation
Factor x 1-4
ΔC/C
(%)
4
2
102
3.3 µF
1.0 µF
0
0.1 µF
-2
101
-4
100
-6
- 60
- 40
- 20
0
20
40
60
80
100
Tamb (°C)
102
120
Impedance as a function of frequency (typical curve)
103
103
104
105
f (Hz)
106
Max. DC and AC voltage as a function of temperature
Impedance
(Ω)
1.2
Factor
Capacitance in µF
102
1
0.1 µF
101
0.8
0.22 µF
0.47 µF
1.0 µF
100
0.6
3.3 µF
10-1
0.4
10-2
0.2
10-3
104
105
106
107
f (Hz)
0
- 60
108
20
60
100
Tamb (°C)
103
103
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
- 20
102
102
0.1 µF
0.22 µF
0.47 µF
0.1 µF
0.22 µF
0.47 µF
1.0 µF
3.3 µF
101
Tamb ≤ 85 °C, 630 VDC
100
102
www.vishay.com
262
103
104
1.0 µF
3.3 µF
101
85 °C < Tamb ≤ 110 °C, 630 VDC
105
106 f (Hz)
107
100
102
103
For technical questions, contact: [email protected]
104
105
106 f (Hz)
107
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors Vishay Roederstein
MKP Axial Type
103
103
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
102
102
0.1 µF
0.22 µF
0.47 µF
0.1 µF
0.22 µF
0.47 µF
1.0 µF
101
1.0 µF
101
Tamb ≤ 85 °C, 850 VDC
100
102
103
85 °C < Tamb ≤ 110 °C, 850 VDC
104
105
106 f (Hz)
107
100
102
103
103
VRMS (V)
102
102
0.1 µF
0.22 µF
0.47 µF
1.0 µF
101
103
105
106 f (Hz)
107
0.1 µF
0.22 µF
0.47 µF
1.0 µF
101
Tamb ≤ 85 °C, 1250 VDC
100
102
104
Max. RMS Voltage (sinewave) as a function of frequency
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
103
85 °C < Tamb ≤ 110 °C, 1250 VDC
104
105
106 f (Hz)
107
100
102
104
105
106 f (Hz)
107
103
103
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
VRMS (V)
Max. RMS Voltage (sinewave) as a function of frequency
103
102
102
0.1 µF
0.22 µF
0.47 µF
0.1 µF
0.22 µF
0.47 µF
101
101
Tamb ≤ 85 °C, 1600 VDC
100
102
10
3
Document Number: 28162
Revision: 21-Apr-10
10
4
10
5
6
10 f (Hz)
7
10
100
102
85 °C < Tamb ≤ 110 °C, 1600 VDC
103
104
For technical questions, contact: [email protected]
105
106 f (Hz)
107
www.vishay.com
263
MKP 1839 HQ
Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Max. allowed component rise (ΔT) as a function of the ambient
temperature (Tamb)
Insulation resistance as a function of ambient temperature
(typical curve)
106
RC (s)
ΔT (°C)
12
10
8
6
105
4
2
104
0
30
60
90
Tamb (°C)
0
- 60
120
- 20
20
60
Tamb (°C)
100
HEAT CONDUCTIVITY (G) AS A FUNCTION OF CAPACITOR BODY THICKNESS IN mW/°C
DIAMETER
(mm)
www.vishay.com
264
HEAT CONDUCTIVITY (mW/°C)
PITCH 26.5 mm
PITCH 31.5 mm
7.0
8
-
8.0
10
-
8.5
11
12
9.5
12
-
10.0
13
15
10.5
-
16
11.0
15
17
11.5
-
18
12.0
-
19
12.5
-
20
13.0
-
21
13.5
-
22
14.0
-
23
15.0
-
25
16.0
-
28
16.5
-
29
18.0
-
32
19.0
-
34
19.5
-
36
20.0
-
37
21.5
-
40
23.0
-
44
23.5
-
45
24.0
-
47
25.5
-
51
28.0
-
57
For technical questions, contact: [email protected]
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors Vishay Roederstein
MKP Axial Type
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors with the typical tgd of the curves”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by ΔT = TC - Tamb.
To avoid radiation or convection, the capacitor should be tested in a wind-free.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC)
2. The peak-to-peak voltage (UP-P) shall not be greater than the maximum (UP-P) to avoid the ionisation inception level
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T
dU
dU 2
2 × ∫ ⎛ --------⎞ × dt < U Rdc × ⎛ --------⎞
⎝ dt ⎠ rated
⎝ dt ⎠
0
T is the pulse duration.
4. The maximum component surface temperature rise must be lower than the limits (see figure max. allowed component
temperature rise).
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table “Heat conductivity”.
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: [email protected]
www.vishay.com
265
MKP 1839 HQ
Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Voltage Conditions for 6 Above
Tamb ≤ 85 °C
85 °C < Tamb ≤ 110 °C
URAC
See “Maximum AC voltage as a
function of temperature par.
characteristics”
Maximum temporary RMS-overvoltage (< 24 h)
1.25 x URAC
0.875 x URAC
Maximum peak voltage (VO-P) (< 2 s)
1.6 x URDC
1.1 x URDC
ALLOWED VOLTAGES
Maximum continuous RMS voltage
INSPECTION REQUIREMENTS
General Notes:
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and
Specific Reference Data”.
Group C Inspection Requirements
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1
Dimensions (detail)
4.3.1
Initial measurements
Capacitance
Tangent of loss angle at 100 kHz
4.3
Robustness of terminations
Tensile: Load 30 N; 10 s
Bending: Load 15 N; 90°
4.4
Resistance to soldering heat
No pre-drying
Method: 1A
Solder bath: 280 °C ± 5 °C
Duration: 10 s
4.4.2
Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 2 % of the value measured initially
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured initially
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
Isopropylalcohol at room temperature
Method: 1
Rubbing material: Cotton wool
Immersion time: 5 min ± 0.5 min
No visible damage
Legible marking
4.14
As specified in chapter “General Data” of this
specification
Solvent resistance of the marking
No visible damage
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
4.6.1
Initial measurements
4.6
Rapid change of temperature
Capacitance
Tangent of loss angle at 100 kHz
θA = - 55 °C
θB = + 110 °C
5 cycles
Duration t = 30 min
Visual examination
www.vishay.com
266
For technical questions, contact: [email protected]
No visible damage
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors Vishay Roederstein
MKP Axial Type
SUB-CLAUSE NUMBER AND TEST
4.7
Vibration
4.7.2
4.9
Final inspection
Shock
4.9.3
Final measurements
CONDITIONS
Mounting:
See section “Mounting” of this specification
Procedure B4
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s²
(whichever is less severe)
Total duration 6 h
Visual examination
Mounting:
See section “Mounting” for more information
Pulse shape: Half sine
Acceleration: 490 m/s²
Duration of pulse: 11 ms
Visual examination
Capacitance
Tangent of loss angle
Insulation resistance
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
4.10
Climatic sequence
4.10.2 Dry heat
4.10.3
4.10.4
Damp heat cyclic
Test Db, first cycle
Cold
Damp heat cyclic
Test Db, remaining cycles
4.10.6.2 Final measurements
PERFORMANCE REQUIREMENTS
No visible damage
No visible damage
|ΔC/C| ≤ 2 % of the value measured initally
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured initially
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
Temperature: 110 °C
Duration: 16 h
Temperature: - 55 °C
Duration: 2 h
4.10.6
Voltage proof = URDC for 1 min within
15 min after removal from testchambers
Visual examination
Capacitance
Tangent of loss angle
Insulation resistance
SUB-GROUP C2
4.11
Damp heat steady state
4.11.1 Initial measurements
4.11.3
Final measurements
Capacitance
Tangent of loss angle at 1 kHz
Visual examination
Voltage proof = URDC for 1 min within
15 min after removal from testchamber
Capacitance
Tangent of loss angle
Insulation resistance
Document Number: 28162
Revision: 21-Apr-10
No breakdown or flashover
No visible damage
Legible marking
|ΔC/C| ≤ 3 % of the value measured initially
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in
4.3.1 or 4.6.1 as applicable
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
No visible damage
Legible marking
No breakdown or flashover
|ΔC/C| ≤ 3 % of the value measured in
4.11.1.
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.11.1
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
For technical questions, contact: [email protected]
www.vishay.com
267
MKP 1839 HQ
Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C3 A
4.12.1
Endurance test at 50 Hz
alternative voltage
Duration: 2000 h
x URDC at 85 °C
0.875 x URDC at 110 °C
4.12.1.1 Initial measurements
Capacitance
Tangent of loss angle at 100 kHz
4.12.1.3 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 5 % compared to values measured
in 4.12.1.1
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.12.1.1
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
For - 55 °C to 20 °C
0 % ≤ |ΔC/C| ≤ 2.75 % or
for 20 °C to 110 °C:
- 5.5 % ≤ |ΔC/C| ≤ 0 %
As specified in section “Capacitance” of this
specification
SUB-GROUP C4
4.2.6
Temperature characteristics
Initial measurement
Intermediate measurements
Capacitance
Capacitance at - 55 °C
Capacitance at 20 °C
Capacitance at 110 °C
4.13
Charge and discharge
10 000 cycles
Charged to URDC
Discharge resistance:
U n ( Vdc )
R = ---------------------------------------2.5 × C ( dU ⁄ dt )
4.13.1
Initial measurements
4.13.3
Final measurements
www.vishay.com
268
Capacitance
Tangent of loss angle at 100 kHz
Capacitance
|ΔC/C| ≤ 3 % of the value measured in 4.13.1
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.13.1
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
For technical questions, contact: [email protected]
Document Number: 28162
Revision: 21-Apr-10
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
Similar pages