HDSP-301x/303x Series HDSP-561x/563x Series 10 mm and 13 mm Slim Font Seven Segment Displays Data Sheet Description These slim font seven segment displays incorporate a new slim font character design. This slim font features narrow width, specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays are painted a neutral gray for enhanced on/off contrast. Features • Excellent appearance • Slim font design • Mitered corners, evenly illuminated segments • Gray face for optimum on/off contrast • Choice of colors: HER, green, yellow, and AlGaAs All devices are available in either common anode or common cathode configuration with right hand decimal point. Devices HER HDSP301E 303E 561E 563E Green HDSP301G 303G 561G 563G Yellow HDSP301Y 303Y 561Y 563Y AlGaAs HDSP301A 303A 561A 563A • Choice of character size: 10 mm and 13 mm • Characterized for luminous intensity Description Common Anode, 10 mm Display Common Cathode, 10 mm Display Common Anode, 13 mm Display Common Cathode, 13 mm Display Part Numbering System 5082 - x xx x - x x x xx HDSP - x xx x - x x x xx Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] A: AlGaAs Red E: High Efficiency Red G: Green Y: Yellow Device Specific Configuration[1] Refer to Respective Data Sheet Package[1] Refer to Respective Data Sheet Notes: 1. For codes not listed in the figure above, please refer to the respective data sheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part-number. Color and Intensity Binbs are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective data sheet for specific bin limit information. HDSP-301x/303x Series Pin Function 1 G 2 F 3 Common A/C 4 E 5 D 6 DP 7 C 8 Common A/C 9 B 10 A HDSP-561x/563x Series Pin Function 1 E 2 D 3 Common A/C 4 C 5 DP 6 B 7 A 8 Common A/C 9 F 10 G Absolute Maximum Ratings Description Average Power per Segment or DP Peak Forward Current per Segment or DP DC Forward Current per Segment or DP Operating Temperature Range Storage Temperature Range Reverse Voltage per Segment or DP Wavesoldering Temperature for 3 Seconds 1.59 mm below body HER 105 90 30 –40 to +80 –40 to +80 5 250 Green 105 90 30 –40 to +80 –40 to +80 5 250 Yellow 105 90 30 –40 to +80 –40 to +80 5 250 AlGaAs 37 45 15 –20 to +80 –40 to +80 5 250 Units mW mA mA ˚C ˚C V ˚C Notes: 1. Derate above 33˚C at 0.34 mA/˚C for HER. 2. Derate above 27˚C at 0.32 mA/˚C for Green. 3. Derate above 30˚C at 0.33 mA/˚C for Yellow. 4. Derate above 60˚C at 0.25 mA/˚C for AlGaAs. Electrical/Optical Characteristics at TA = 25˚C HER Device Series HDSP301/303E HER Device Series HDSP561/563E Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Min. 1.100 Typ. 1.800 Max. Units mcd Test Conditions IF = 10 mA VF 1.90 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 635 625 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Min. 1.100 Typ. 1.800 Max. Units mcd Test Conditions IF = 10 mA VF 1.90 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 635 625 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Green Device Series HDSP301/303G Green Device Series HDSP561/563G Yellow Device Series HDSP301/303Y Parameter Luminous Intensity/Segment (digit average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Min. 1.800 Typ. 2.800 Max. Units mcd Test Conditions IF = 10 mA VF 2.25 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 568 573 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Min. 1.800 Typ. 2.800 Max. Units mcd Test Conditions IF = 10 mA VF 2.25 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 568 573 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Min. 1.100 Typ. 1.800 Max. Units mcd Test Conditions IF = 10 mA VF 2.15 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 589 590 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Yellow Device Series HDSP561/563Y Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Min. 1.800 Typ. 2.800 Max. Units mcd Test Conditions IF = 10 mA VF 2.15 2.50 V IF = 20 mA λPEAK λd IR RθJ–PIN 589 590 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Notes: 1. Typical specification for reference only. Do not exceed absolute maximum ratings. 2. The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. AlGaAs Device Series HDSP301/303A AlGaAs Device Series HDSP561/563A Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Parameter Luminous Intensity/Segment (Digit Average) Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength Reverse Current Thermal Resistance LED Junction-to-Pin Symbol IV Min. 0.280 Typ. 0.450 Max. Units mcd Test Conditions IF = 1 mA VF 1.80 2.20 V IF = 20 mA λPEAK λd IR RθJ–PIN 660 643 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Min. 0.280 Typ. 0.450 Max. Units mcd Test Conditions IF = 1 mA VF 1.80 2.20 V IF = 20 mA λPEAK λd IR RθJ–PIN 660 643 nm nm µA ˚C/W/Seg. IF = 20 mA IF = 20 mA VR = 5 V 100 351.5 Notes: 1. Typical specification for reference only. Do not exceed absolute maximum ratings. 2. The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. Intensity Bin Limits (mcd) Green Color Categories HDSP-301G/303G/561G/563G IV Bin Category Min. K 1.800 L2.800 Max. 3.600 5.600 Yellow HDSP-301Y/303Y IV Bin Category I K Min. Max. 1.1002.200 1.800 3.600 Yellow HDSP-561Y/563Y IV Bin Category Min. K 1.800 L2.800 Max. 3.600 5.600 HER HDSP-301E/303E IV Bin Category I K Min. Max. 1.1002.200 1.800 3.600 AlGaAs Red HDSP-301A/303A/561A/563A IV Bin Category Min. F 0.280 G 0.450 Max. 0.560 0.900 HER HDSP-561E/563E IV Bin Category Min. Max. K 2.001 3.2 L 3.201 5.05 Note: Tolerance is ± 10% Dominant Wavelength (nm) Color Bin Min. Green 3 570.00 4 567.00 Yellow2 586.50 3 584.00 Max. 574.50 571.50 590.00 587.50 Note: 1. All categories are established for classification of products. Products may not be available in all categories. Please contact your Avago representatives for further clarification/information. HDSP-301x/303x Series Figure 1. Maximum allowable DC current vs. ambient temperature. Figure 2. Forward current vs. forward voltage. Figure 3. Relative luminous intensity vs. DC forward current. Figure 5. Forward current vs. forward voltage. Figure 6. Relative luminous intensity vs. DC forward current. HDSP-561x/563x Series Figure 4. Maximum allowable DC current vs. ambient temperature. Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. Soldering/Cleaning Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs, please refer to Application Note 1027. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Limited. All rights reserved. Obsoletes 5989-2834EN AV02-0625EN - July 26, 2007