DF005S THRU DF10S MINIATURE GLASS PASSIVATED SINGLE-PHASE SURFACE MOUNT BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere FEATURES Case Style DFS 0.047 (1.20) 0.040 (1.02) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL recognized under Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High surge overload rating-50 amperes peak ♦ Ideal for printed circuit boards ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 0.205 (5.2) 0.195 (5.0) 0.404 (10.3) 0.386 (9.80) 0.335 (8.51) 0.320 (8.13) 45o 0.255 (6.5) 0.245 (6.2) MECHANICAL DATA 0.013 (0.330) 0.130 (3.3) 0.009 (0.241) 0.120 (3.05) 0.060 (1.524) 0.040 (1.016) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Mounting Position: Any Weight: 0.04 ounce, 1.0 gram 0.013 (0.330) 0.003 (0.076) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS DF 005S DF 01S DF 02S DF 04S DF 06S DF 08S DF 10S UNITS 100 200 400 600 800 1000 Volts Maximum repetitive peak reverse voltage VRRM 50 Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward output rectified current at TA=40°C (NOTE 2) I(AV) 1.0 Amp Peak forward surge current single half sine-wave superimposed on rated load (JEDEC Method) TJ=150°C IFSM 50.0 Amps Rating for fusing (t < 8.3ms) I2t 10.0 A2sec Maximum instantaneous forward voltage drop per leg at 1.0A VF 1.1 Volts Maximum DC reverse current at rated DC blocking voltage per leg IR 5.0 500 µA CJ 25.0 pF RΘJA RΘJL 40.0 15.0 °C/W -55 to +150 °C TA=25°C TA=125°C Typical junction capacitance per leg (NOTE 1) Typical thermal resistance per leg (NOTE 2) Operating junction and storage temperature range TJ, TSTG NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Units mounted on P.C.B. with 0.51 x 0.51” (13 x 13mm) copper pads 4/98 RATINGS AND CHARACTERISTICS CURVES DF005S THRU DF10S FIG.1 - DERATING CURVE OUTPUT RECTIFIED CURRENT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.5 P.C.B. MOUNTED ON 0.51 x 0.51” (13 x 13mm) COPPER PADS 0 20 40 60 80 100 120 140 60 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.0 TJ=150°C SINGLE SINE-WAVE (JEDEC Method) 50 40 30 1.0 CYCLE 20 10 0 160 1 10 AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG 100 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 REVERSE VOLTAGE, VOLTS 0.1 TJ=25°C 0 20 40 60 80 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 -TYPICAL JUNCTION CAPACITANCE 1 TJ=125°C 10 0.01 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1 100 NUMBER OF CYCLES AT 60 Hz 100 100 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100