H 2 mm x 5 mm Rectangular LED Lamps Technical Data Features HLMP-S100 HLMP-S20X Series HLMP-S30X Series HLMP-S40X Series HLMP-S50X Series HLMP-S600 Package Dimensions • Rectangular Light Emitting Surface • Excellent for Flush Mounting on Panels • Choice of Five Bright Colors • Long Life: Solid State Reliability • Excellent Uniformity of Light Output Description The HLMP-S100, -S200, -S300, -S400, -S500, S600 are epoxy encapsulated lamps in rectangular packages which are easily stacked in arrays or used for discrete front panel indicators. Contrast and light uniformity are enhanced by a special epoxy diffusion and tinting process. The HLMP-S100 uses double heterojunction (DH) absorbing substrate (AS) aluminum gallium arsenide (AlGaAs) LEDs to produce outstanding light output 5964-9379E 1-153 Electrical/Optical Characteristics at TA = 25°C Sym. Iv 2θ1/2 Description Luminous Intensity Included Angle Between Half Luminous Intensity Points λPEAK Peak Wavelength Device HLMPAlGaAs Red S100 High Efficiency Red S200 S201 Orange S400 S401 Yellow S300 S301 Green S500 S501 Emerald Green S600[4] Min. Typ. 3.4 7.5 2.1 3.4 3.5 7.5 2.1 3.4 3.5 7.5 1.4 2.2 2.1 4.0 2.6 4.2 4.0 8.0 1.0 3.0 Max. Units mcd IF = 20 mA IF = 20 mA See Note 1 All 110 Deg. AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green 645 635 600 583 565 558 nm Measurement at Peak See Note 2 Time const, e-t/τs λd Dominant Wavelength AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green 637 626 602 585 569 560 nm τs Speed of Response AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green 30 90 280 90 500 3100 ns C Capacitance AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green 30 11 4 15 18 35 pF All 260 °C/W RθJ-PIN Thermal Resistance VF Forward Voltage AlGaAs Red HER/Orange Yellow Green/Emerald Green 1.6 1.5 1.5 1.5 VR Reverse Breakdown Voltage All 5.0 1-154 Test Conditions 1.8 1.9 2.1 2.2 2.2 2.6 2.6 3.0 VF = 0; f = 1 MHz Junction to Cathode Lead at Seating Plane V IF = 20 mA V IR = 100 µA Electrical/Optical Characteristics at TA = 25°C (cont’d) Sym. ηV Description Luminous Efficacy Device HLMP- Min. Typ. AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green Max. Units 80 145 380 500 595 656 lumens/ watt Test Conditions See Note 3 Notes: 1. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/ηv, where Iv is the luminous intensity in candelas and ηv is the luminous efficacy in lumens/watt. 4. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation. Absolute Maximum Ratings at TA = 25°C Yellow Green/ Emerald Green Units 90 60 90 mA 20 25 20 25 mA 30 30 20 30 mA AlGaAs Red High Efficiency Red/Orange Peak Forward Current 300 Average Forward Current[1] Parameter [2] DC Current Transient Forward Current[3] (10 µsec Pulse) 500 LED Junction Temperature 110 Operating Temperature Range -20 to +100 Storage Temperature Range -55 to +100 mA 110 110 -55 to +100 -55 to +100 Lead Soldering Temperature [1.6 mm (0.063 in.) below seating plane] 110 °C -20 to +100 °C -55 to +100 260°C for 5 seconds Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. For AlGaAs Red, Red, Orange, and Green series derate linearly from 50°C at 0.5 mA/°C. For Yellow series derate linearly from 50°C at 0.34 mA/°C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wire bond. It is not recommended that the device be operated at peak currents beyond the peak forward current listed in the Absolute Maximum Ratings. 1.0 ORANGE RELATIVE INTENSITY EMERALD GREEN TA = 25° C AlGaAs RED HIGH PERFORMANCE GREEN HIGH EFFICIENCY RED 0.5 YELLOW 0 500 550 600 650 700 750 WAVELENGTH – nm Figure 1. Relative Intensity vs. Wavelength. 1-155 Figure 2. Forward Current vs. Forward Voltage Characteristics. VF (300 mA) for AlGaAs Red = 2.6 Volts Typical. Figure 3. Relative Luminous Intensity vs. DC Forward Current. Figure 5. Maximum Tolerable Peak Current vs. Peak Duration. (IPEAK MAX Determined from Temperature Derated IDC MAX). Figure 6. Relative Luminous Intensity vs. Angular Displacement. 1-156 Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. LED Peak Current. ηv (300 mA) for AlGaAs Red = 0.7.