DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Features Functional Block Diagram (SOT-89) 18.5 dB Gain @ 6 GHz 24.5 dB Gain @ 850 MHz 36.0 dBm Output IP3 @ 850 MHz 3.5 dB Noise Figure @ 850 MHz 20.3 dBm P1dB @ 850 MHz Low Performance Variation Over Temperature Low Cost: Die Form or SOT-89 Package 100% DC On-Wafer Testing ESD Protection on All Die: >1000V HBM Low Thermal Resistance: <80ºC/Watt Ground 4 1 Input 2 3 Ground Output Bias Absolute Maximum Ratings Max Device Voltage Max Device Current Max Device Dissipated Power RF Input Power Storage Temperature Junction Temperature Operating Temperature Thermal Resistance EDS (HBM) Description The CGB7014-SC (-BD) is a Darlington Configured, high dynamic range, utility gain block amplifier. Designed for applications operating within the DC to 8.0 GHz frequency range, Mimix’s broadband, cascadable, gain block amplifiers are ideal solutions for transmit, receive and IF applications. These MMIC amplifiers are available in bare die form or an industry standard SOT-89 package. Mimix's InGaP HBT technology and an industry low thermal resistance offers a thermally robust and reliable gain block solution. +6.0 V 130 mA 0.65 W +17 dBm -55ºC to 150ºC 150ºC -40ºC to +85ºC 80º C/W 1000 V Operation of this device above any of these parameters may cause permanent damage. The InGaP HBT die have extra pads to enable thorough DC testing. This unique test capability and the inclusion of ESD protection on all die, significantly enhances the quality, reliability and ruggedness of these products. Applications PA Driver Amp, IF Amp, LO Buffer Amp Cellular, PCS, GSM, UMTS Wireless Data and SATCOM WLAN 802.11a/b/g and WiMAX Transmit and Receive Functions CATV With a single bypass capacitor, optional RF choke and two DC blocking capacitors, this gain block amplifier offers significant ease of use in a broad range of applications. Electrical Characteristics Unless otherwise specified, the following specifications are guaranteed at room temperature in a Mimix test fixture. Parameter Small Signal Gain Output P1dB Output IP3 Noise Figure Operating Current Input Return Loss Output Return Loss Pout @ -45 dBc, ACP IS-95, 9 Forward Channels Temperature (ºC) Min. +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 23.5 23.2 19.3 19.0 34.5 34.0 76 72 9 8 9 8 850 MHz Typ. Max. 24.5 24.5 20.3 20.3 36.0 36.0 3.5 3.5 80 80 12 12 13 13 13.5 13.5 25.5 25.8 4.3 4.7 85 89 Min. 22.0 21.7 18.0 17.7 30.0 29.0 76 72 13 12 12 11 Notes: 1. Test Conditions in Mimix eval board, Vs = 8 V, Id = 80 mA Typ., Rbias = 39 2. Values reflect performance in recommended application circuit. 1950 MHz Typ. Max. 23.0 23.0 19.0 19.0 31.5 31.5 3.5 3.5 80 80 19 19 17 17 13.5 13.5 24.0 24.3 4.3 4.7 85 89 , Zs = Zl = 50 Min. 21.5 21.2 17.1 16.8 28.5 27.5 76 72 12 11 11 10 2400 MHz Typ. Max. 22.5 22.5 18.1 18.1 30.0 30.0 3.6 3.6 80 80 18 18 16 16 23.5 23.8 4.6 5.0 85 89 Min. 3500 MHz Typ. Max. Min. 21.5 21.5 16.0 16.0 27.0 27.0 3.8 3.8 80 80 14 14 17 17 6000 MHz Typ. 18.5 18.5 10.0 10.0 19.0 19.0 4.5 4.5 80 80 9 9 18 18 Max. Units dB dB dBm dBm dBm dBm dB dB mA mA dB dB dB dB dBm dBm , OIP3 tone spacing = 1 MHz, Pout per tone = 6 dBm. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Typical S-Parameter and Noise Performance |S21| Vs Frequency 26 24 25 C -40 C 85 C 25 C -40 C 85 C -8 |S11| (dB) 22 |S21| (dB) |S11| Vs Frequency -4 20 18 16 -12 -16 14 12 -20 0 1 2 3 4 5 6 7 0 8 1 2 3 Frequency (GHz) 7 8 6 7 8 25 C -40 C 85 C -8 |S22| (dB) |S12| (dB) 6 -4 25 C -40 C 85 C -22 5 |S22| Vs Frequency |S12| Vs Frequency -20 4 Frequency (GHz) -24 -26 -12 -16 -28 -30 -20 0 1 2 3 4 5 Frequency (GHz) 6 7 8 0 1 2 3 4 5 Frequency (GHz) Noise Figure Vs Frequency 5.5 Noise Figure (dB) 5 25 C -40 C 85 C 4.5 4 3.5 3 2.5 2 0 1 2 3 4 5 6 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Typical Power and Linearity Performance OIP3 Vs Frequency P1dB Vs Frequency 22 38 20 25 C -40 C 85 C 18 OIP3 (dBm) 16 P1dB (dBm) 25 C -40 C 85 C 34 14 12 10 8 30 26 22 18 1 MHz separation, 6 dBm/tone 6 14 4 0 1 2 3 4 5 6 7 0 8 1 2 3 4 5 6 7 8 Frequency (GHz) Frequency (GHz) Linearity Performance - Base Station ACP – IS-95 ACP @ 850 MHz Vs Pout 9 Channels Forward, 750 kHz Offset 30 kHz BW Alt1 Ch. Pwr @ 850 MHz Vs Pout 9 Channels Forward, 1.98 MHz Offset 30 kHz BW -30 -45 -35 ACP (dBc) ACP (dBc) -40 25 C -40 C 85 C -55 25 C -40 C 85 C -45 -50 -65 -75 -55 -85 -60 4 8 12 16 4 20 8 Pout (dBm) 20 -40 25 C -40 C 85 C 25 C -40 C 85 C -50 ACP (dBc) -40 ACP (dBc) 16 Alt1 Ch. Pwr @ 1950 MHz Vs Pout 9 Channels Forward, 1.25 MHz Offset 12.5 kHz BW ACP @ 1950 MHz Vs. Pout 9 Forward Channels, 885 kHz Offset 30 kHz BW -30 12 Pout (dBm) -50 -60 -60 -70 -70 -80 4 8 12 Pout (dBm) 16 20 4 8 12 16 20 Pout (dBm) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Typical Scattering Parameters (Vd = +4.75V, Icc = 77 mA, T = 23°C, device in a 50 ohm system) Frequency (MHz) 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300 4400 4500 4600 4700 4800 4900 5000 S 11 (Mag) 0.26 0.26 0.25 0.26 0.25 0.25 0.25 0.24 0.24 0.24 0.23 0.23 0.22 0.21 0.21 0.21 0.20 0.19 0.19 0.19 0.18 0.17 0.18 0.17 0.17 0.18 0.18 0.17 0.18 0.18 0.19 0.18 0.19 0.19 0.19 0.20 0.20 0.20 0.21 0.21 0.22 0.21 0.21 0.22 0.22 0.22 0.22 0.22 0.21 0.21 S 21 S 12 (Ang) (Mag) (Ang) 179 178 176 174 174 170 169 167 166 167 163 162 164 161 162 160 160 160 160 162 161 161 163 167 165 166 169 167 167 167 169 168 165 167 165 164 165 163 161 159 159 155 151 150 147 143 140 137 132 127 17.9 17.9 17.8 17.8 17.6 17.5 17.4 17.2 17.1 16.9 16.7 16.7 16.3 16.1 16.0 15.7 15.5 15.3 15.1 14.8 14.6 14.4 14.1 13.8 13.6 13.4 13.1 13.0 12.9 12.7 12.5 12.3 12.2 12.0 11.9 11.7 11.5 11.4 11.2 11.1 10.9 10.8 10.7 10.6 10.5 10.4 10.2 10.1 10.1 10 175 169 164 159 154 148 143 138 133 128 122 117 113 107 103 97 93 88 83 78 73 68 64 60 55 51 47 42 38 33 29 25 21 16 11 8 3 -1 -5 -10 -14 -18 -22 -26 -31 -35 -39 -44 -48 -52 Continues Next Page. (Mag) 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 S 22 (Ang) (Mag) (Ang) -1 -3 -4 -5 -7 -8 -9 -11 -12 -14 -15 -16 -18 -19 -21 -22 -24 -25 -27 -29 -30 -32 -34 -35 -37 -39 -41 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -64 -66 -69 -71 -73 -75 -78 -80 -82 -85 -87 -89 0.06 0.06 0.06 0.07 0.08 0.08 0.09 0.09 0.10 0.11 0.11 0.12 0.13 0.13 0.14 0.14 0.15 0.15 0.16 0.16 0.16 0.16 0.17 0.18 0.17 0.18 0.19 0.18 0.19 0.19 0.20 0.20 0.20 0.21 0.21 0.21 0.22 0.23 0.23 0.23 0.23 0.24 0.24 0.24 0.25 0.24 0.25 0.26 0.26 0.25 -174 -164 -159 -158 -154 -154 -155 -152 -154 -152 -155 -158 -156 -157 -161 -162 -163 -164 -167 -169 -170 -172 -174 -175 -176 -179 -180 179 176 174 173 172 169 166 166 163 161 158 155 153 149 148 144 140 137 134 130 127 123 118 S-Parameter Data Files are available online at: www.mimixbroadband.com Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Typical Scattering Parameters (Vd = +4.75V, Icc = 77 mA, T = 23°C, device in a 50 ohm system) Frequency (MHz) 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 7000 7100 7200 7300 7400 7500 7600 7700 7800 7900 8000 8100 8200 8300 8400 8500 8600 8700 8800 8900 9000 9100 9200 9300 9400 9500 9600 9700 9800 9900 10000 S 11 S 21 (Mag) (Ang) (Mag) 0.21 0.20 0.20 0.20 0.20 0.19 0.20 0.20 0.19 0.20 0.20 0.20 0.20 0.22 0.23 0.24 0.26 0.27 0.29 0.31 0.34 0.37 0.39 0.42 0.44 0.46 0.49 0.51 0.53 0.55 0.57 0.60 0.61 0.63 0.64 0.65 0.67 0.68 0.69 0.69 0.70 0.71 0.71 0.72 0.72 0.72 0.72 0.73 0.73 0.73 125 121 115 109 104 97 89 83 73 64 55 46 35 24 18 6 -2 -10 -18 -26 -34 -40 -49 -55 -61 -68 -73 -79 -84 -90 -95 -99 -105 -110 -114 -118 -123 -127 -131 -135 -139 -142 -146 -150 -153 -156 -160 -163 -166 -169 9.8 9.7 9.6 9.6 9.5 9.4 9.3 9.2 9.2 9.1 9.0 9.0 8.9 8.8 8.7 8.6 8.5 8.3 8.2 8.0 7.9 7.7 7.5 7.3 7.1 6.9 6.7 6.5 6.2 6.0 5.7 5.5 5.3 5.1 4.8 4.6 4.4 4.2 4.0 3.8 3.6 3.5 3.3 3.1 3.0 2.8 2.7 2.6 2.5 2.4 S 12 (Ang) -57 -61 -65 -70 -74 -79 -83 -88 -92 -97 -102 -107 -112 -117 -122 -127 -132 -137 -143 -148 -153 -159 -164 -169 -175 180 174 169 164 159 154 149 144 139 134 130 125 121 116 112 108 104 100 95 92 88 84 81 77 73 (Mag) 0.08 0.09 0.09 0.09 0.09 0.09 0.09 0.09 0.09 0.09 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.09 0.09 0.09 0.09 0.09 0.08 0.08 0.08 0.08 0.08 0.07 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.06 0.06 0.05 S 22 (Ang) -92 -95 -98 -100 -103 -106 -109 -113 -116 -119 -122 -125 -129 -132 -136 -140 -143 -147 -151 -155 -159 -163 -167 -171 -175 -179 177 174 170 166 162 159 155 151 148 145 141 138 135 133 130 127 124 121 118 116 113 111 109 107 (Mag) 0.25 0.26 0.27 0.27 0.27 0.27 0.27 0.28 0.29 0.29 0.29 0.30 0.30 0.30 0.31 0.32 0.32 0.33 0.34 0.35 0.36 0.37 0.38 0.39 0.40 0.41 0.42 0.43 0.44 0.45 0.46 0.47 0.48 0.48 0.49 0.50 0.51 0.51 0.51 0.52 0.52 0.52 0.53 0.53 0.53 0.53 0.53 0.54 0.54 0.54 (Ang) 114 111 107 102 96 92 87 80 75 68 62 55 49 42 34 27 20 13 6 -2 -9 -17 -24 -31 -39 -45 -52 -59 -65 -71 -77 -83 -89 -94 -99 -104 -109 -114 -118 -123 -127 -131 -135 -139 -142 -146 -149 -152 -155 -159 S-Parameter Data Files are available online at: www.mimixbroadband.com Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Application Circuit Note: This schematic represents the topology of the application circuit recommended by Mimix. R Bias = (Vs - Vd) / Id Recommended Bias Resistor Values for ID = 80 mA 7V Rbias (R1 Description: 1206 1/4W 1%) 25 Rbias (R1 Description: 1210 1/2W 1%) — 8V 39 — Vd 10V 12V — 64 Note: Rbias provides DC bias stability over temperature. R1 — C3 4 89 uuuu Supply Voltage (V) Vs L1 1 RF IN C1 Ref Designator C1, C2 C3 Value 1000 pF 1.0 F L1 R1 C4 56 nH RF OUT 3 C2 2 Description MCH185A101JK VITR 1.0 F 25V CER CAP 0805 X7R 10% Coilcraft 0603 CS 10% R B ia s = ( V s - V d) / Id DNP ( Do Not P la ce) Size 0805 0805 0603 1206 / 1210 N/A MIMIX Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Physical Dimensions - SC Package (SOT-89) 4.50 [0.177] 1.55 [0.061] 0.71 [0.028] 1.73 [0.068] 0.38 [0.015] 1.70 [0.067] 4 1 0.46 [0.18] 3X 3.48 [0.137] XXXXXXX XXXXXX ZYYWW 0.41 [0.016] 2 2.50 [0.096] 3 4.41 [0.163] 2.06 [0.081] 5.33 [0.210] 0.99 [0.039] 1.27 [0.050] 0.58 [0.023] 1.50 [0.059] 3.00 [0.118] 0.38 [0.015] 0.76 [0.030] 0.64 [0.025] DIMENSIONS IN MILLIMETERS [INCHES] 0.86 [0.034] 3.86 [0.152] MARKINGS: XXXXXXX = MIMIX MODEL NO. XXXXXX = WAFER LOT NO. ZYYWW = DATE CODE (YR/WEEK) FIRST LETTER COUNTRY OF ORIGIN IF OTHER THAT USA Physical Dimensions - BD (Bare Die) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 7 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. DC-8.0 GHz InGaP HBT, MMIC or Packaged Matched Gain Block Amplifier September 2006 - Rev 18-Sep-06 CGB7014-SC (-BD) Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matt tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes. Ordering Information Part Number for Ordering CGB7014-BD CGB7014-SC-0G00 CGB7014-SC-0G0T CGB7014-SP-0G00 CGB7014-SP-0G0T PB-CGB7014-SC-0000 PB-CGB7014-SP-0000 Description Bare die in GelPak Matte Tin plated RoHS compliant SOT-89 surface mount package in bulk quantity Matte Tin plated RoHS compliant SOT-89 surface mount package in tape and reel Matte Tin plated RoHS compliant SOT-86 surface mount package in bulk quantity Matte Tin plated RoHS compliant SOT-86 surface mount package in tape and reel Evaluation Board for SOT-89 packaged device with SMA connectors Evaluation Board for SOT-86 packaged device with SMA connectors We also offer the plastic packages with SnPb (Tin-Lead) or NiPdAu plating. Please contact your regional sales manager for more information regarding different plating types Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 8 of 8 Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.