MURS305 - MURS360 SURFACE MOUNT SUPER FAST RECOVERY DIODES VOLTAGE RANGE: 50 - 600V CURRENT: 3.0 A Features ! Glass Passivated Die Construction ! Ideally Suited for Automatic Assembly ! Low Forward Voltage Drop, High Efficiency ! Low Power Loss ! Super-Fast Recovery Time Plastic Case Material has UL Flammability ! Classification Rating 94V-O B SMC/DO-214AB Mechanical Data A ! ! Case: SMC/DO-214AB, Molded Plastic Terminals: Solder Plated, Solderable ! ! ! per MIL-STD-750, Method 2026 Polarity: Cathode Band or Cathode Notch Marking: Type Number Weight: 0.21 grams (approx.) C D J H Maximum Ratings and Electrical Characteristics G E Dim Min Max A 5.59 6.22 B 6.60 7.11 C 2.75 3.18 D 0.15 0.31 8.13 E 7.75 G 0.10 0.20 H 0.76 1.52 J 2.00 2.62 All Dimensions in mm TA = 25C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbol MURS305 MURS310 MURS315 MURS320 MURS330 MURS340 MURS36 0 Unit Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current 50 100 150 200 300 400 600 V VR(RMS) 35 70 105 140 210 280 420 V IO 3.0 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100 A Forward Voltage @IF = 3.0A VFM @TA = 25°C @TA = 100°C IRM 5.0 500 µA Reverse Recovery Time (Note 1) trr 35 nS Typical Junction Capacitance (Note 2) Cj 45 pF RJL 16 °C/W Tj, TSTG -65 to +150 °C Peak Reverse Current At Rated DC Blocking Voltage @TL = 75°C VRRM VRWM VR Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range 0.95 1.25 1.7 V Note: 1. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A. See figure 5. 2. Measured at 1.0 MHz and applied reverse voltage of 4.0 V DC. 3. Mounted on P.C. Board with 8.0mm2 land area. 1 of 2 www.sunmate.tw IF, INSTANTANEOUS FORWARD CURRENT (A) 100 MURS305-MURS320 10 MURS330-MURS340 MURS360 1.0 0.1 0.01 0.6 Tj = 25°C Pulse width = 300µs 2% duty cycle 1.0 1.4 1.8 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics 1000 8.3ms single half sine-wave 100 Cj, CAPACITANCE (pF) IFSM, PEAK FORWARD SURGE CURRENT (A) 200 10 1 10 NUMBER OF CYCLES AT 60Hz Fig. 3 Peak Forward Surge Current 100 100 10 1 10 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Junction Capacitance trr +0.5A 50Ω NI (Non-inductive) 10Ω NI Device Under Test (-) 0A (+) Pulse Generator (Note 2) 50V DC Approx (-) 1.0Ω NI -0.25A (+) Oscilloscope (Note 1) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50Ω. -1.0A Set time base for 5/10ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit 2 of 2 www.sunmate.tw 100