AKM AK4129 6ch 216khz / 24-bit asynchronous src Datasheet

[AK4129]
AK4129
6ch 216kHz / 24-Bit Asynchronous SRC
GENERAL DESCRIPTION
The AK4129 is an 6ch digital sample rate converter (SRC). The input sample rate ranges from 8kHz to
216kHz. The output sample rate is from 8kHz to 216kHz. The AK4129 has an internal Oscillator and does
not need any external master clocks. It contributes simplifying a system configuration. The AK4129
supports master mode and TDM data interface, enabling simultaneous input of asynchronous stereo
data. The AK4129 is suitable for the application interfacing to different sample rates such as multi-channel
high-end Car Audio Systems and DVD recorders.
FEATURES
• 6 channels input/output
• Asynchronous Sample Rate Converter
• Input Sample Rate Range (FSI): 8kHz ∼ 216kHz
• Output Sample Rate Range (FSO): 8kHz ∼ 216kHz
• Input to Output Sample Rate Ratio: 1/6 to 6
• THD+N: −130dB
• Dynamic Range: 140dB (A-weighted)
• I/F format: MSB justified, LSB justified and I2S compatible and TDM
• Oscillator for Internal Operation Clock
• Clock for Master mode: 128/256/384/512/768fso
• On-chip X’tal oscillator
• Digital De-emphasis Filter (32kHz, 44.1kHz and 48kHz)
• Soft Mute Function
• SRC Bypass mode (Master/Slave)
• μP Interface: I²C bus
• Power Supply: AVDD, DVDD1-4: 3.0 ∼ 3.6V (typ. 3.3V)
• Ta = −20 ∼ 85°C (AK4129EQ), −40 ∼ 85°C (AK4129VQ)
• Package: 64LQFP
MS1173-E-02
2011/06
-1-
DITHER
SMT1
SMT0
SMSEMI
SMUTE
VSS2-5
DVDD1-4
INAS
DEM1
DEM0
IDIF2
IDIF1
IDIF0
[AK4129]
OLRCK
OBICK
SRC1
Bypass
Input
Serial
Audio
I/F
IBICK1
ILRCK1
SDTI1
DEM
FIR
SRC
SMUTE
+
Dither
0.5 LSB
SRC
IBICK2
ILRCK2
SDTI2
DEM
FIR
+
SMUTE
SRC
SRC
Dither
DEM
FIR
SDTO2
SRC3
+
SMUTE
SRC
ODIF1
ODIF0
Output
Serial
Audio
I/F
0.5 LSB
Bypass
Input
Serial
Audio
I/F
IBICK3
ILRCK3
SDTI3
OBIT1
OBIT2
SRC2
Bypass
Input
Serial
Audio
I/F
SDTO1
SRC
Dither
SDTO3
0.5 LSB
Internal
OSC
IMCLK
PDN
PM1
PM2
UNLOCK
Bypass
uP
I/F
CAD0
X 'tal
Osc
.
MCKO
Clock
Div
SDA SCL XTO OMCLK/XTI
SPB
Internal
Regulator
SRC
CM2 CM1 CM0
REF
AVDD
VSS1
VD18
DITHER
SMT1
SMT0
SMSEMI
SMUTE
VSS2-5
DVDD1-4
INAS
DEM1
DEM0
IDIF2
IDIF1
IDIF0
Figure 1. AK4129 Block Diagram (Synchronous mode INAS pin = “L”)
OLRCK
OBICK
SRC1
Bypass
Input
Serial
Audio
I/F
BICK1
LRCK1
SDTI1
DEM
FIR
SRC
SMUTE
SRC
Dither
+
BICK2
LRCK2
SDTI2
DEM
FIR
SRC
SMUTE
SRC
Dither
DEM
FIR
SRC
ODIF1
ODIF0
SRC2
Output
Serial
Audio
I/F
+
0.5LSB
SDTO2
SRC3
Bypass
Input
Serial
Audio
I/F
BICK3
LRCK3
SDTI3
OBIT1
OBIT0
0.5LSB
Bypass
Input
Serial
Audio
I/F
SDTO1
SMUTE
SRC
Dither
+
SDTO3
0.5LSB
Internal
OSC
IMCLK
PDN
PM1
PM2
UNLOCK
Bypass
uP
I/F
CAD0
X 'tal
Osc .
SDA SCL XTO OMCLK/XTI
SPB
Clock
Div.
CM2 CM1 CM0
MCKO
SRC
Internal
Regulator
REF
AVDD
VSS1
VD18
Figure 2. AK4129 Block Diagram (Asynchronous mode INAS pin = “H”)
MS1173-E-02
2011/06
-2-
[AK4129]
■ Compatibility with AK4126
(1) Specifications
Parameter
Stereo Inputs
Asynchronous Mode
Internal Clock
Bypass Mode
Master Mode for
Output Ports
Maximum FSI and
FSO
Maximum IBICK and
OBICK Frequency
X’tal Oscillator
Master Clock Output
TDM Mode
AK4126
Not Available
Synchronous Mode Only
AK4129
Available
The INAS pin controls synchronous and
asynchronous modes.
Internal PLL
Internal Regulator + Internal Oscillator
The PLL2-0 pins must be set
PLL reference clock select is not needed since
according to the PLL reference clock.
internal oscillator generates the clock.
#61 pin: A pin for external devices of
#61 pin: A capacitor pin for the internal regulator.
PLL filter.
Not Available
Available
Controlled by CM2-0 pins or BYPS bit.
Not Available
Available
Controlled by CM2-0 pins
192kHz
216kHz
64fs
256fs
Not Available
Not Available
Not Available
Available
Available
Available
Controlled by IDIF2-0 pins or IDIF2-0 bits (Input)
Controlled by TDM pin (Output)
Individual Setting Available
Individual setting is available by setting SMUTE3-1
bits in serial control mode.
Individual Setting Available
Individual setting is available by DEM31-30,
21-20, 11-10 bits in serial control mode.
Individual Setting Available
Individual setting is available by IDIF32-30, 22-20,
12-10 bits in serial control mode.
Available
Parallel and Serial control modes are selected by the
SPB pin.
FSI:FSO Ratio Change Detect
Detects over-current/voltage of the 1.8V outputs.
Soft Mute
All channels are controlled together.
De-emphasis Filter
All channels are controlled together.
Audio Format for
Input port.
All channels are controlled together.
I2C
Not Available
UNLOCK pin
Detects PLL unlock.
MS1173-E-02
2011/06
-3-
[AK4129]
(2) Pins
Pin#
AK4126
AK4129 pin
1
2
14
15
18
32
33
47
48
49
51
54
55
56
57
58
59
61
NC
TEST0
TST1
TST2
TST4
TST5
NC
TEST4
NC
NC
TST8
PLL2
PLL1
PLL0
TST9
TST10
NC
FILT
IBICK2
IMCLK
ILRCK3
IBICK3
INAS
PM2
TDM
OMCLK/XTI
XTO
MCKO
CAD0
TST1
SMSEMI
TST2
SCL
SDA
SPB
VD18
63
TST11
TST3
64
NC
*: An external device is needed for the No 61 pin.
ILRCK2
AK4126
AK4129
6ch mode AK4126 compatible
(PM2/1 pin = “LL”)
L
L
L
L
L
L
L
L
L
L
L
L or H
L or H
L or H
L
L
L
*
AK4126: “Open”
AK4129: “L”
L
AK4129
FILT
VD18
R
C2
1uF
C1
Figure 3. AK4126
(Please refer to the AK4126 datasheet about external devices.)
MS1173-E-02
Figure 4. AK4129
2011/06
-4-
[AK4129]
■ Ordering Guide
−20 ∼ +85°C
64pin LQFP (0.5mm pitch)
−40 ∼ +85°C
64pin LQFP (0.5mm pitch)
Evaluation Board for AK4129
AK4129EQ
AK4129VQ
AKD4129
MCKO
DVDD3
TST7
SDTO1
SDTO2
SD TO3
ODIF0
ODIF1
CM0
CM1
CM2
TDM
42
41
40
39
38
37
36
35
34
33
OBICK
45
VSS4
OLRCK
46
43
OMCLK/XTI
47
44
XTO
48
■ Pin Layout
49
32
PM 2
TST0
50
31
OBIT1
CAD0
51
30
OBIT0
D VDD4
52
29
PM 1
VSS5
53
28
DEM 1
TST1
54
27
DEM 0
SMSEM I
55
26
SM T1
TST2
56
25
SM T0
SCL
57
24
PDN
SDA
58
23
DITHER
SPB
59
22
SM UTE
AVDD
60
21
VSS3
VD 18
61
20
DVDD 2
VSS1
62
19
UNLOCK
TST3
63
18
INAS
IL RCK2
64
17
TST6
4
5
6
7
8
9
10
11
12
13
14
15
16
VSS2
TST4
SDTI1
SDTI2
SDTI3
IDIF0
IDIF1
IDIF2
ILRCK3
IBICK3
TST5
3
ILRCK1
IBICK1
2
IMCLK
DVDD1
1
IBICK2
Top View
MS1173-E-02
2011/06
-5-
[AK4129]
PIN / FUNCTION
No.
Pin Name
I/O
1
IBICK2
I
2
3
4
5
6
7
8
9
10
11
12
13
IMCLK
ILRCK1
IBICK1
DVDD1
VSS2
TST4
SDTI1
SDTI2
SDTI3
IDIF0
IDIF1
IDIF2
I
I
I
I
I
I
I
I
I
I
14
ILRCK3
I
15
IBICK3
I
16
TST5
I
17
TST6
I
18
INAS
I
19
UNLOCK
O
20
21
22
23
DVDD2
VSS3
SMUTE
DITHER
I
I
24
PDN
I
25
26
27
28
29
30
31
32
SMT0
SMT1
DEM0
DEM1
PM1
OBIT0
OBIT1
PM2
I
I
I
I
I
I
I
I
33
TDM
I
Function
Audio Serial Data Clock #2 Pin
When the INAS pin = “L”, this pin should be connected to VSS2-5.
Master Clock Input Pin for Input PORT
Input Channel Clock #1 Pin
Audio Serial Data Clock #1 Pin
Digital Power Supply Pin, 3.0 ∼ 3.6V
Digital Ground Pin
Test Pin. This pin should be connected to VSS2-5.
Audio Serial Data Input #1 Pin
Audio Serial Data Input #2 Pin
Audio Serial Data Input #3 Pin
Audio Interface Format #0 Pin for Input PORT (Note 2)
Audio Interface Format #1 Pin for Input PORT (Note 2)
Audio Interface Format #2 Pin for Input PORT (Note 2)
Input Channel Clock #3 Pin
When the INAS pin = “L”, this pin should be connected to VSS2-5.
Audio Serial Data Clock #3 Pin
When the INAS pin = “L”, this pin should be connected to VSS2-5.
Test Pin.
This pin should be connected to VSS2-5.
Test Pin.
This pin should be connected to VSS2-5.
Asynchronous Mode Select Pin.
“L”(connected to the ground): Synchronous mode.
“H”(connected to DVDD1-4) : Asynchronous mode.
Unlock Status Pin
When the PDN pin= “L”, this pin outputs “H”.
Digital Power Supply Pin, 3.0 ∼ 3.6V
Digital Ground Pin
Soft Mute Pin (Note 3)
“H” : Soft Mute, “L” : Normal Operation
Dither Enable Pin
“H” : Dither ON, “L” : Dither OFF
Power-Down Mode Pin
“H”: Power up, “L”: Power down reset and initializes the control register.
The AK4129 should be reset once by bringing PDN pin = “L” upon power-up.
Soft Mute Timer Select #0 Pin
Soft Mute Timer Select #1 Pin
De-emphasis Control #0 Pin (Note 4)
De-emphasis Control #1 Pin (Note 4)
Channel Mode Select #1 Pin
Bit Length Select #0 Pin for Output Data
Bit Length Select #1 Pin for Output Data
Channel Mode Select #2 Pin
TDM Format Select Pin.
“L”(connected to the ground): Stereo mode.
“H”(connected to DVDD1-4) : TDM mode.
MS1173-E-02
2011/06
-6-
[AK4129]
No.
34
35
36
37
38
Pin Name
CM2
CM1
CM0
ODIF1
ODIF0
I/O
I
I
I
I
I
39
SDTO3
O
40
SDTO2
O
41
SDTO1
O
42
43
44
TST7
VSS4
DVDD3
O
-
45
OBICK
I/ O
46
OLRCK
I/ O
47
OMCLK/XTI
I
48
XTO
O
49
MCKO
O
50
TST0
I
51
CAD0
I
52
53
54
DVDD4
VSS5
TST1
I
55
SMSEMI
I
56
TST2
I
57
SCL
I
58
SDA
I/ O
59
SPB
I
Function
Clock Select or Mode Select #2 Pin for Output PORT
Clock Select or Mode Select #1 Pin for Output PORT
Clock Select or Mode Select #0 Pin for Output PORT
Audio Interface Format #1 Pin for Output PORT
Audio Interface Format #0 Pin for Output PORT
Audio Serial Data Output #3 Pin for Output PORT
When the PDN pin = “L”, the SDRO3 pin outputs “L”.
Audio Serial Data Output #2 Pin for Output PORT
When the PDN pin = “L”, the SDTO2 pin outputs “L”.
Audio Serial Data Output #1 Pin for Output PORT
When the PDN pin = “L”, the SDTO1 pin outputs “L”.
Test Pin. This pin should be open.
Digital Ground Pin
Digital Power Supply Pin, 3.0 ∼ 3.6V
Audio Serial Data Clock Pin for Output PORT
When the PDN pin = “L” in master mode, the OBOCK pin outputs “L”.
Output Channel Clock Pin for Output PORT
When the PDN pin = “L” in master mode, the OBOCK pin outputs “L”.
External Master Clock Input / X’tal Input Pin
X’tal Output Pin
When the PDN pin = “L”, XTO outputs Hi-z.
Master Clock Output Pin
When the PM2 pin = “H” and PDN pin = “L”, the MCKO pin outputs “L”.
When the PM2 pin = “L” and PDN pin = “L”, the MCKO pin outputs Hi-z.
Test Pin. This pin should be connected to VSS2-5.
Chip Address 0 pin
This pin must be connected to VSS2-5 in parallel control mode (SPB pin = “L”).
Digital Power Supply Pin, 3.0 ∼ 3.6V
Digital Ground Pin
Test Pin. This pin should be connected to VSS2-5.
Soft Mute Semi-auto Mode Setting Pin
“H”: Semi-auto, “L”: Manual Mode
Test Pin. This pin should be connected to VSS2-5.
I2C Control Data Clock Pin, (when the SPB pin= “H”)
Since there is a protection diode between this pin and DVDD1-4, connect pulled-up
resister to DVDD1-4 + 0.3V or less. This pin must be connected to the VSS2-5 in
parallel control mode (PSB pin= “L”).
I2C Control Data In/Out put Pin, (when the SPB pin= “H”)
Since there is a protection diode between this pin and DVDD1-4, connect pulled-up
resister to DVDD1-4 + 0.3V or less. This pin must be connected to the VSS2-5 in
parallel control mode (PSB pin= “L”).
Parallel/Serial Control Mode Select Pin
“H”: Serial Control Mode, “L”: Parallel Control Mode
MS1173-E-02
2011/06
-7-
[AK4129]
No.
60
Pin Name
AVDD
I/O
-
Function
Analog Power Supply Pin, 3.0 ∼ 3.6V
Digital Power Output Pin, Typ 1.8V
When the PDN pin= “L”, the DV18 pin outputs “L”. Current must not be taken from
this pin. A 1μF (±30%; including the temperature characteristics) capacitor should
61 VD18
O
be connected between this pin and DVSS. When this capacitor is polarized, the
positive polarity pin should be connected to the VD18 pin.
62 VSS1
Analog Ground Pin
Test Pin.
63 TST3
I
This pin should be connected to VSS2-5.
Input Channel Clock #2 Pin
64 ILRCK2
I
When INAS pin = “L”, this pin should be connected to VSS2-5.
Note: All input pins should not be left floating. DVDD1-4 must be connected to the same power supply.
Note 1. SPB, CM2-0, INAS, PM2-1, OBIT1-0, TDM, ODIF1-0, IDIF2-0 and CAD0 pin must be changed when the PDN
pin= “L”.
Note 2. In parallel control mode (SPB pin = “L”), IDIF2-0 pins control all SRC1~3 audio interface input formats.
In serial control mode (SPB pin = “H”), the setting of IDIF2-0 pins is ignored. The IDIF[12:10] bits setting is
reflected to SRC1, the IDIF[22:20] bits setting is reflected to SRC2 and the IDIF[32:30] bits setting is reflected
to SRC3.
Note 3. In parallel control mode (SPB pin = “L”), the SMUTE pin controls all SRC1~3 soft mute.
In serial control mode (SPB pin = “H”), the SUMUTE pin setting is ignored. The SMUTE1 bit setting is
reflected to SRC1, the SMUTE2 bit setting is reflected to SRC2 and the SMUTE3 bit setting is reflected to
SRC3.
Note 4. In parallel control mode (SPB pin= “L”), DEM1-0 pins control all SRC1~3 de-emphasis settings.
In serial control mode (SPB pin= “H”), setting of DEM1-0 pins is ignored. DEM[11:10] bits setting is reflected
to SRC1, DEM[21:20] bits setting is reflected to SRC2 and DEM[31:30] bits setting is reflected to SRC3.
■ Handling of Unused Pins
The unused I/O pins should be processed appropriately as below.
Classification
Digital
Pin Name
Setting
IBICK2, IMCLK, SDTI3, ILRCK3,
IBICK3, SMUTE, DITHER,
These pins must be connected to VSS2-5.
OMCLK/XTI, ILRCK2, SDA, SCL,
CAD0, TST0-6
UNLOCK, SDTO1-3, MCKO, XTO,
These pins must be open.
TST7
MS1173-E-02
2011/06
-8-
[AK4129]
ABSOLUTE MAXIMUM RATINGS
(VSS1-5=0V; Note 5)
Parameter
Symbol
min
max
Units
Analog
AVDD
−0.3
4.2
V
Digital
DVDD1-4
−0.3
4.2
V
Input Current, Any Pin Except Supplies
IIN
±10
mA
Digital Input Voltage
(Note 6)
VIND
−0.3
DVDD1-4+0.3
V
Ambient Temperature
AK4129EQ
Ta
−20
85
°C
(Power applied) (Note 7)
AK4129VQ
Ta
−40
85
°C
Storage Temperature
Tstg
−65
150
°C
Note 5. All voltages with respect to ground. VSS1-5 must be connected to the same ground.
Note 6. IMCLK, IBICK3-1, ILRCK3-1, IDIF2-0, INAS, SUMTE, DITHER, PDN, SMT1-0, DEM1-0, PM2-1, OBIT1-0,
TDM, CM2-0, ODIF1-0, SDTO4-1, OBICK, OLRCK, OMCLK/XTI, CAD0, SMSEMI, SCL, SDA and SPB
pins.
Note 7. In case that wiring density is 100%.
Note 8. DVDD1-4 pins must be connected to the same power supply.
Power Supplies:
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(VSS1-5=0V; Note 5)
Parameter
Symbol
min
typ
max
Units
Power Supplies:
Analog
AVDD
3.0
3.3
3.6
V
(Note 9)
Digital
DVDD1-4
3.0
3.3
3.6
V
Difference
AVDD - DVDD1-4
-0.3
0
+0.3
V
Note 5. All voltages with respect to ground. VSS1-5 must be connected to the same ground.
Note 9. The power up sequence between AVDD and DVDD1-4 is not critical but the PDN pin must be “L” until all power
supplies are ON, then put the PDN pin to “H”.
WARNING: AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS1173-E-02
2011/06
-9-
[AK4129]
SRC CHARACTERISTICS
(Ta=25°C; AVDD=DVDD1-4=3.3V; VSS1-5=0V; Signal Frequency = 1kHz; data = 24bit;
Measurement bandwidth = 20Hz ~ FSO/2; unless otherwise specified.)
Parameter
Symbol
min
SRC Characteristics:
Resolution
Input Sample Rate
FSI
8
Output Sample Rate
FSO
8
THD+N
(Input = 1kHz, 0dBFS, Note 10)
FSO/FSI = 44.1kHz/48kHz
FSO/FSI = 48kHz/44.1kHz
FSO/FSI = 48kHz/192kHz
FSO/FSI = 192kHz/48kHz
Worst Case (FSO/FSI = 32kHz/176.4kHz)
Dynamic Range (Input = 1kHz, −60dBFS, Note 10)
FSO/FSI = 44.1kHz/48kHz
FSO/FSI = 48kHz/44.1kHz
FSO/FSI = 48kHz/192kHz
FSO/FSI = 192kHz/48kHz
Worst Case (FSO/FSI = 48kHz/32kHz)
132
Dynamic Range (Input = 1kHz, −60dBFS, A-weighted, Note 10)
FSO/FSI = 44.1kHz/48kHz
Ratio between Input and Output Sample Rate
FSO/FSI
1/6
Note 10. Measured by Audio Precision System Two Cascade.
typ
max
Units
24
216
216
Bits
kHz
kHz
−130
−124
−133
−124
-
-91
dB
dB
dB
dB
dB
136
136
136
132
-
-
dB
dB
dB
dB
dB
140
6
dB
-
POWER CONSUMPTION
(Ta= 25°C; AVDD=DVDD1-4=3.0~3.6V; VSS1-5=0V; Signal Frequency=1kHz; data=24bit; Asynchronous Input mode
(INAS pin = “H”), Output PORT: Master mode, OMCLK/XTI are input via a X’tal. PM2/1 pin = “H/L” 6ch original mode,
unless otherwise specified.)
Parameter
min
typ
max
Units
Power Supplies
Power Supply Current
Normal operation (PDN pin = “H”)
AVDD+DVDD1-4
mA
33
FSI=FSO=48kHz: AVDD=DVDD1-4=3.3V (Note 12)
mA
84
FSI=FSO=192kHz: AVDD=DVDD1-4=3.3V (Note 13)
mA
164
85
: AVDD=DVDD1-4=3.6V (Note 14)
Power down (PDN pin = “L”) (Note 11)
μA
100
10
AVDD+DVDD1-4
Note 11. All digital input pins are held to VSS2-5.
Note 12. It is 33 [mA] (typ) when the OMCLK/XTI pin is supplied a 6.144MHz external clock and the output port is in
slave mode.
Note 13. It is 82 [mA] (typ) when the OMCLK/XTI pin is supplied a 6.144MHz external clock and the output port is in
slave mode.
Note 14. It is 83 [mA] (typ) when the OMCLK/XTI pin is supplied a 6.144MHz external clock and the output port is in
slave mode.
MS1173-E-02
2011/06
- 10 -
[AK4129]
FILTER CHARACTERISTICS
(Ta= 25°C; AVDD=DVDD1-4=3.0 ∼ 3.6V)
Parameter
Symbol
min
typ
max
Units
Digital Filter
0.4583FSI
Passband −0.01dB
0.985 ≤ FSO/FSI ≤ 6.000
PB
0
kHz
0.4167FSI
0.905 ≤ FSO/FSI < 0.985
PB
0
kHz
0.3195FSI
0.714 ≤ FSO/FSI < 0.905
PB
0
kHz
0.2852FSI
0.656 ≤ FSO/FSI < 0.714
PB
0
kHz
0.2182FSI
0.536 ≤ FSO/FSI < 0.656
PB
0
kHz
0.2177FSI
0.492 ≤ FSO/FSI < 0.536
PB
0
kHz
0.1948FSI
0.452 ≤ FSO/FSI < 0.492
PB
0
kHz
0.1458FSI
0.357 ≤ FSO/FSI < 0.452
PB
0
kHz
0.1302FSI
0.324 ≤ FSO/FSI < 0.357
PB
0
kHz
0.0917FSI
0.246 ≤ FSO/FSI < 0.324
PB
0
kHz
0.0826FSI
0.226 ≤ FSO/FSI < 0.246
PB
0
kHz
0.0583FSI
0.1667 ≤ FSO/FSI < 0.226
PB
0
kHz
Stopband
0.985 ≤ FSO/FSI ≤ 6.000
SB
0.5417FSI
kHz
0.905 ≤ FSO/FSI < 0.985
SB
0.5021FSI
kHz
0.714 ≤ FSO/FSI < 0.905
SB
0.3965FSI
kHz
0.656 ≤ FSO/FSI < 0.714
SB
0.3643FSI
kHz
0.536 ≤ FSO/FSI < 0.656
SB
0.2974FSI
kHz
0.492 ≤ FSO/FSI < 0.536
SB
0.2813FSI
kHz
0.452 ≤ FSO/FSI < 0.492
SB
0.2604FSI
kHz
0.357 ≤ FSO/FSI < 0.452
SB
0.2116FSI
kHz
0.324 ≤ FSO/FSI < 0.357
SB
0.1969FSI
kHz
0.246 ≤ FSO/FSI < 0.324
SB
0.1573FSI
kHz
0.226 ≤ FSO/FSI < 0.246
SB
0.1471FSI
kHz
0.1667 ≤ FSO/FSI < 0.226
SB
0.1020FSI
kHz
Passband Ripple
PR
±0.01
dB
Stopband
0.985 ≤ FSO/FSI ≤ 6.000
SA
121.2
dB
Attenuation
0.905 ≤ FSO/FSI < 0.985
SA
121.4
dB
0.714 ≤ FSO/FSI < 0.905
SA
115.3
dB
0.656 ≤ FSO/FSI < 0.714
SA
116.9
dB
0.536 ≤ FSO/FSI < 0.656
SA
114.6
dB
0.492 ≤ FSO/FSI < 0.536
SA
100.2
dB
0.452 ≤ FSO/FSI < 0.492
SA
103.3
dB
0.357 ≤ FSO/FSI < 0.452
SA
102.0
dB
0.324 ≤ FSO/FSI < 0.357
SA
103.6
dB
0.246 ≤ FSO/FSI < 0.324
SA
103.3
dB
0.226 ≤ FSO/FSI < 0.246
SA
101.5
dB
0.1667 ≤ FSO/FSI < 0.226
SA
73.2
dB
Group Delay
(Note 15)
GD
64
1/fs
Note 15. This value is the time from the rising edge of ILRCK after SDTI data is input to rising edge of OLRCK before the
SDTO data is output, when OLRCK data corresponds with ILRCK data.
MS1173-E-02
2011/06
- 11 -
[AK4129]
DC CHARACTERISTICS
(Ta= 25°C; AVDD=DVDD1-4=3.0 ∼ 3.6V)
Parameter
High-Level Input Voltage
Low-Level Input Voltage
High-Level Output Voltage
Except the SDA pin
(Iout=−400μA)
Low-Level Output Voltage
Except the SDA pin
(Iout=400μA)
SDA pin
(Iout=3mA)
Input Leakage Current
Symbol
VIH
VIL
min
70%DVDD1-4
-
typ
-
max
30%DVDD1-4
Units
V
V
VOH
DVDD1-4
−0.4
-
-
V
VOL
VOL
-
-
0.4
0.4
V
V
Iin
-
-
±10
μA
SWITCHING CHARACTERISTICS
(Ta= 25°C; AVDD=DVDD1-4=3.0 ∼ 3.6V; CL=20pF)
Parameter
Symbol
min
typ
max
Units
Master Clock Timing
fXTAL
11.2896
24.576
MHz
Crystal Oscillator Frequency
IMCLK Input
Frequency
fECLK
1.024
36.864
MHz
Duty
dECLK
40
50
60
%
OMCLK Input
128 FSO :
fCLK
1.024
27.648
MHz
Pulse Width Low
tCLKL
13
ns
Pulse Width High
tCLKH
13
ns
256 FSO :
fCLK
2.048
27.648
MHz
Pulse Width Low
tCLKL
13
ns
Pulse Width High
tCLKH
13
ns
384 FSO :
fCLK
3.072
36.864
MHz
Pulse Width Low
tCLKL
10
ns
Pulse Width High
tCLKH
10
ns
512 FSO :
fCLK
4.096
27.648
MHz
Pulse Width Low
tCLKL
13
ns
Pulse Width High
tCLKH
13
ns
768 FSO :
fCLK
6.144
36.864
MHz
Pulse Width Low
tCLKL
10
ns
Pulse Width High
tCLKH
10
ns
MCKO Output
Frequency
fMCK
1.024
36.864
MHz
Duty (Note 16)
dMCLK
40
50
60
%
Note 16. This is a value of MCKO output duty when the master clock for output ports is supplied by a crystal oscillator.
MS1173-E-02
2011/06
- 12 -
[AK4129]
Input PORT LRCK for Stereo Mode (ILRCK1-3)
Frequency
Duty Cycle
Slave Mode
Output PORT LRCK for Stereo Mode (OLRCK)
Frequency
Slave mode
Master mode OMCLK Input 128FSO mode
Master mode OMCLK Input 256FSO mode
Master mode OMCLK Input 384FSO mode
Master mode OMCLK Input 512FSO mode
Master mode OMCLK Input 768FSO mode
Duty Cycle
Slave Mode
Master Mode
Input PORT LRCK for TDM256 Mode (ILRCK1)
Asynchronous Inputs Mode (INAS pin = “L”)
Frequency
“H” time (slave mode)
“L” time (slave mode)
Output PORT LRCK for TDM256 Mode (OLRCK)
Frequency
“H” time (slave mode)
“L” time (slave mode)
“H” time
(Master mode, TDM256 24bit MSB justified)
“L” time
(Master mode, TDM256 24bit I2S)
Audio Interface Timing
Input PORT ( Stereo Slave mode)
IBICK1-3 Period (FSI= 8kHz ∼ 54kHz)
(FSI=54kHz ∼ 108kHz)
(FSI=108kHz ∼ 216kHz)
IBICK1-3 Pulse Width Low
Pulse Width High
ILRCK1-3 Edge to IBICK1-3 “↑”(Note 17)
IBICK1-3 “↑” to ILRCK1-3 Edge (Note 17)
SDTI1-3 Hold Time from IBICK1-3 “↑”
SDTI1-3 Setup Time to IBICK1-3 “↑”
Input PORT (TDM256 slave mode)
IBICK1 Period
IBICK1 Pulse Width Low
Pulse Width High
ILRCK1 Edge to IBICK1 “↑”
(Note 17)
IBICK1 “↑” to ILRCK1 Edge
(Note 17)
SDTI1 Hold Time from IBICK1 “↑”
SDTI1 Setup Time to IBICK1 “↑”
Output PORT ( Stereo Slave mode)
OBICK Period (FSO= 8kHz ∼ 54kHz)
(FSO= 54kHz ∼ 108kHz)
(FSO=108kHz ∼ 216kHz)
OBICK Pulse Width Low
Pulse Width High
OLRCK Edge to OBICK “↑” (Note 17)
OBICK “↑” to OLRCK Edge (Note 17)
OLRCK to SDTO1-3 (MSB) (Except I2S mode)
OBICK “↓” to SDTO1-3
FSI
Duty
8
48
FSO
FSO
FSO
FSO
FSO
FSO
Duty
Duty
8
8
8
8
8
8
48
FSI
tLRH
tLRL
216
52
kHz
%
216
216
108
96
54
48
52
kHz
kHz
kHz
kHz
kHz
kHz
%
%
8
1/256FSI
1/256 FSI
48
kHz
ns
ns
FSO
tLRH
tLRL
8
1/256 FSO
1/256 FSO
48
kHz
ns
ns
tLRH
-
1/8 FSO
-
ns
tLRL
-
1/8 FSO
-
ns
tBCK
tBCK
tBCK
tBCKL
tBCKH
tLRB
tBLR
tSDH
tSDS
1/256 FSI
1/128 FSI
1/64 FSI
27
27
15
15
15
15
ns
ns
ns
ns
ns
ns
ns
ns
ns
tBCK
tBCKL
tBCKH
tLRB
tBLR
tSDH
tSDS
81
32
32
20
20
20
10
ns
ns
ns
ns
ns
ns
ns
tBCK
tBCK
tBCK
tBCKL
tBCKH
tLRB
tBLR
tLRS
tBSD
1/256 FSO
1/128 FSO
1/64 FSO
27
27
20
20
ns
ns
ns
ns
ns
ns
ns
ns
ns
MS1173-E-02
50
50
50
20
20
2011/06
- 13 -
[AK4129]
Output PORT (TDM256 slave mode)
OBICK Period
tBCK
81
ns
OBICK Pulse Width Low
tBCKL
32
ns
Pulse Width High
tBCKH
32
ns
OLRCK Edge to OBICK “↑”
(Note 17)
tLRB
20
ns
OBICK “↑” to OLRCK Edge
(Note 17)
tBLR
20
ns
OBICK “↓” to SDTO1
tBSD
20
ns
Output PORT (Stereo Master mode)
OBICK Frequency
fBCK
64 FSO
Hz
OBICK Duty
dBCK
50
%
OBICK “↓” to OLRCK Edge
tMBLR
−20
20
ns
OBICK “↓” to SDTO1-3
tBSD
−20
20
ns
Output PORT (TDM256 master mode)
OBICK Frequency
fBCK
Hz
256 FSO
OBICK Duty
dBCK
%
50(Note 19)
OBICK “↓” to OLRCK Edge
10
tMBLR
ns
−10
OBICK “↓” to SDTO1
20
tBSD
ns
−20
Reset Timing
tPD
150
ns
PDN Pulse Width
(Note 18)
Note 17. BICK rising edge must not occur at the same time as LRCK edge.
Note 18. The AK4129 can be reset by bringing the PDN pin = “L”.
Note 19. When OMCLK=512FSO. If the OMCLK=256FSO, OMCLK clock is though and output from the OBICK pin.
When OMCLK = 384FSO, dBCK= (tCLKH)/(tCLKH+1/fCLK) x100 [%] or (tCLKL)/(tCLKL+1/fCLK) x100
[%]. When OMCLK=768FSO, dBCK= (1/fCLK)/(3/fCLK) x100 [%].
OMCLK=384FSO
1/fCLK
1/fCLK
tCLKH
OMCLK pin
tCLKL
tCLKL
tCLKH
OBICK pin Ouput
(TDM256
Master mode)
tCLKL
1/fCLK
1/fCLK
OMCLK=768FSO
1/fCLK
1/fCLK
1/fCLK
OMCLK pin
1/fCLK
OBICK pin Output
(TDM256
Master mode)
3/fCLK
3/fCLK
MS1173-E-02
2011/06
- 14 -
[AK4129]
Parameter
Symbol
min
typ
2
Control Interface Timing (I C Bus):
fSCL
SCL Clock Frequency
1.3
tBUF
Bus Free Time Between Transmissions
0.6
tHD:STA
Start Condition Hold Time
(prior to first clock pulse)
1.3
tLOW
Clock Low Time
0.6
tHIGH
Clock High Time
0.6
tSU:STA
Setup Time for Repeated Start Condition
0
tHD:DAT
SDA Hold Time from SCL Falling (Note 20)
0.1
tSU:DAT
SDA Setup Time from SCL Rising
tR
Rise Time of Both SDA and SCL Lines
tF
Fall Time of Both SDA and SCL Lines
0.6
tSU:STO
Setup Time for Stop Condition
0
tSP
Pulse Width of Spike Noise
Suppressed by Input Filter
Cb
Capacitive load on bus
Note 20. Data must be held for sufficient time to bridge the 300 ns transition time of SCL.
MS1173-E-02
max
Units
400
-
kHz
μs
μs
0.3
0.3
50
μs
μs
μs
μs
μs
μs
μs
μs
ns
400
pF
2011/06
- 15 -
[AK4129]
■ Timing Diagram
1/fECLK
VIH
IMCLK(I)
VIL
tECLKH
tECLKL
dECLK
= tECLKH (or tECLKL) x fECLK x 100
1/fCLK
VIH
OMCLK(I)
VIL
tCLKH
tCLKL
1/fMCK
MCKO(O)
50%DVDD
tMCKH
tMCKL
dMCLK
= tMCKH (or tMCKL) x fMCK x 100
Figure 5. IMCLK, OMCLK, MCKO Clock Timing
•Stereo Mode and Slave Mode
1/FSI
VIH
LRCK1-3(I)
VIL
tLRCH
tLRCL
Duty
= tLRCH (or tLRCL) x FSI x 100
tBCK
VIH
IBICK1-3(I)
VIL
tBCKH
tBCKL
•TDM256 Mode and Slave Mode
1/FSI
VIH
LRCK1(I)
VIL
tLRH
tLRL
tBCK
VIH
IBICK1(I)
VIL
tBCKH
tBCKL
Figure 6. ILRCK1-3, IBICK1-3 Clock Timing
MS1173-E-02
2011/06
- 16 -
[AK4129]
• Stereo Mode and Slave Mode
1/FSO
VIH
OLRCK(I)
VIL
tLRCH
tLRCL
Duty
= tLRCH (or tLRCL) x FSO x 100
tBCK
VIH
OBICK(I)
VIL
tBCKH
tBCKL
• TDM256 Mode and Slave Mode
1/FSO
VIH
OLRCK(I)
VIL
tLRH
tLRL
tBCK
VIH
OBICK(I)
VIL
tBCKH
tBCKL
Figure 7. OLRCK, OBICK, Clock Timing (Slave Mode)
• Stereo Mode and Master Mode
1/FSO
50%DVDD
OLRCK(O)
tLRCH
tLRCL
Duty
= tLRCH (or tLRCL) x FSO x 100
1/ fBCK
OBICK(O)
50%DVDD
tBICKH
tBICKL
dBCK
= tBICKH(or tBICKL) x fBCK x 100
• TDM256 Mode and Master Mode
1/FSO
50%DVDD
OLRCK(O)
24bit MSB justified
tLRH
1/FSO
50%DVDD
OLRCK(O)
2
24bit I S
tLRL
1/ fBCK
OBICK(O)
50%DVDD
tBICKH
tBICKL
dBCK
= tBICKH(or tBICKL) x fBCK x 100
Figure 8. OLRCK, OBICK, Clock Timing (Master Mode)
MS1173-E-02
2011/06
- 17 -
[AK4129]
VIH
ILRCK 1 -3
VIL
tBLR
tLRB
VIH
IBICK 1- 3
VIL
tSDS
tSDH
VIH
SDTI 1 -3
VIL
Figure 9. Input PORT Audio Interface Timing (Stereo Slave mode and TDM256 Slave Mode)
VIH
O LRCK
VIL
tBLR
tLRB
VIH
O BICK
VIL
tBSD
tLRS
SDTO 1- 3
50% D VDD
Figure 10. Output PORT Audio Interface Timing (TDM256 Slave mode & Stereo Slave mode)
MS1173-E-02
2011/06
- 18 -
[AK4129]
OLRCK
50%DVDD
tMBLR
50%DVDD
OBICK
tBSD
50%DVDD
SDTO1-3
Figure 11. Output PORT Audio Interface Timing (TDM256 Master mode & Stereo Master mode)
tPD
PDN
VIL
Figure 12. Power Down Timing
VIH
SDA
VIL
tLOW
tBUF
tR
tHIGH
tF
tSP
VIH
SCL
VIL
tHD:STA
Stop
tHD:DAT
tSU:DAT
Start
tSU:STA
tSU:STO
Start
Stop
Figure 13. I2C Bus Timing
MS1173-E-02
2011/06
- 19 -
[AK4129]
OPERATION OVERVIEW
■ Synchronous and Asynchronous Modes Setting
There are two modes of operation: asynchronous and synchronous modes. The AK4129 is set to Synchronous mode when
the INAS pin is “L” and it is set to Asynchronous mode when the INAS pin is “H”.
FSI pin
Mode
Data
LRCK
BICK
SDTI1
IBICK1
Synchro
ILRCK1
SDTI2
L
(Note 22)
nous
(Note 21)
SDTI3
SDTI1
ILRCK1
IBICK1
Asynchr
H
SDTI2
ILRCK2
IBICK 2
onous
SDTI3
ILRCK3
IBICK 3
Note 21. ILRCK2-3 pins must be connected to VSS2-5.
Note 22. IBICK2-3 pins must be connected to VSS2-5.
Table 1. Input Data Synchronous/Asynchronous Mode Setting
■ Audio Interface Format for Input PORT
The audio data format of input port is MSB first, 2’s complement format. The SDTI1, SDTI2 and SDTI3 are latched on the
rising edge of IBICK1, IBICK2 and IBICK3 respectively.
In parallel control mode (SPB pin= “L”), IDIF2-0 pins control all audio interface formats of SRC1~3. IDIF2-0 pins must be
set during the PDN pin= “L”.
In serial control mode (SPB pin = “H”), setting of IDIF2-0 pins is ignored. IDIF[12:10] bits setting is reflected to SRC1,
IDIF[22:20] bits setting is reflected to SRC2, and IDIF[32:30] bits setting is reflected to SRC3.
IDIF[12:10] bits should be changed after all SDTO1 output codes become zero during soft mute by SMUTE1 bit = “1” or
the SMUTE pin = “H”. IDIF[22:20] bits should be changed after all SDTO2 output codes become zero during soft mute by
SMUTE2 bit = “1” or the SMUTE pin = “H”. IDIF[32:30] bits should be changed after all SDTO3 output codes become
zero during soft mute by SMUTE3 bit = “1” or the SMUTE pin = “H”.
TDM mode (Mode 5/6) can be set in Synchronous Inputs mode (INAS pin = “L”). Serial data for 6channels should be input
from the SDTI1 pin. In this mode, connect SDTI2-3 pins to VDD2-5 because there pins are ignored.
Asynchronous Inputs mode (INAS pin = “H”) does not support TDM mode. The AK4129 is not able to operate correctly
because of SDTI1-3 data inputs are incorrect. TDM mode is must be OFF, when using the AK4129 in asynchronous inputs
mode (INAS pin = “H”). The maximum input frequency of IBICK1-3 is 256FSI.
MS1173-E-02
2011/06
- 20 -
[AK4129]
Mode
0
1
2
3
4
5
6
IDIF2
Pin
(Note 23)
L
L
L
IDIF1
Pin
(Note 23)
L
L
H
IDIF0
Pin
(Note 23)
L
H
L
SDTI1-3 Format
ILRCK
1-3
IBICK
1-3
IBICK1-3
Freq
16bit, LSB justified
≥ 32FSI
20bit, LSB justified
≥ 40FSI
24bit, MSB justified
≥ 48FSI
24/16bit, I2S Compatible
≥ 48FSI
Input
Input
L
H
H
2
S
Compatible
32FSI
16bit, I
H
L
L
24bit, LSB justified
≥ 48FSI
H
L
H
TDM 24bit, MSB justified
256FSI
H
H
X
TDM 24bit, I2S Compatible
256FSI
Table 2. Input PORT Audio Interface Format (Parallel Control Mode, SPB pin= “L”) (X: Don’t care)
Note 23. In serial control mode (SPB pin = “H”), setting of IDIF2-0 pins is ignored. IDIF[12:10] bits setting is reflected to
SRC1, IDIF[22:20] bits setting is reflected to SRC2, and IDIF[32:30] bits setting is reflected to SRC3.
ILRCK
0 1 2 3
9 10 11 12 13 14 15 0 1 2 3
9 10 11 12 13 14 15 0 1
IBICK(32fs)
SDTI(i)
15 14 13
7 6 5 4 3 2 1 0 15 14 13
0 1 2 3
17 18 19 20
31 0 1 2 3
7 6 5 4 3 2 1 0 15
17 18 19 20
31 0 1
IBICK(64fs)
SDTI(i)
Don't Care
15 14 13 12
1 0
Don't Care
15 14 13 12
2 1 0
15:MSB, 0:LSB
Lch Data
Rch Data
Figure 14. Mode 0 Timing (16bit, LSB justified)
ILRCK
0 1 2
12 13
24
31 0 1 2
12 13
24
31 0 1
IBICK(64fs)
SDTI(i)
19
Don't Care
8
1 0
Don't Care
19
8
1 0
19:MSB, 0:LSB
Lch Data
Rch Data
Figure 15. Mode 1 Timing (20bit, LSB justified)
ILRCK
0 1 2
20 21 22 23 24
31 0 1 2
20 21 22 23 24
31 0 1
IBICK(64fs)
SDTI(i)
23 22
4 3 2 1 0
Don't Care 23 22
4 3 2 1 0
Don't Care 23
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 16. Mode 2 Timing (24bit, MSB justified)
MS1173-E-02
2011/06
- 21 -
[AK4129]
ILRCK
0 1 2 3
21 22 23 24 25
0 1 2
21 22 23 24 25
0 1
IBICK(64fs)
23 22
SDTI(i)
4 3 2 1 0 Don't Care 23 22
4 3 2 1 0
Don't Care
23:MSB, 0:LSB
Lch Data
Rch Data
2
Figure 17. Mode 3 Timing (24bit I S)
ILRCK
0 1 2
8 9
24
31 0 1 2
8 9
24
31 0 1
IBICK(64fs)
Don't Care
SDTI(i)
23
1 0
8
Don't Care
8
23
1 0
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 18. Mode 4 Timing (24bit, LSB justified)
Note: SDTI is identified as SDTI1, SDTI2, and SDTI3, ILRCK is identified as ILRCK1, ILRCK2, and ILRCK3, IBICK is
identified as IBICK1, IBICK2, and IBICK3.
256 IBICK
ILRCK1(I)
IBICK1 (I: 256FSI)
SDTI1(I)
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
L1
R1
L2
R2
L3
R3
32 IBICK
32 IBICK
32 IBICK
32 IBICK
32 IBICK
32 IBICK
23 22
Figure 19. Mode 5 Timing (TDM, 24bit, MSB justified, SDTI2-3: Don’t care)
256 IBICK
ILRCK1(I)
IBICK1(I: 256FSI)
SDTI1(I)
23
0
23
0
23
0
23
0
23
0
23
0
L1
R1
L2
R2
L3
R3
32 IBICK
32 IBICK
32 IBICK
32 IBICK
32 IBICK
32 IBICK
23
Figure 20. Mode 6 Timing (TDM, I2S, SDTI2-3: Don’t care)
MS1173-E-02
2011/06
- 22 -
[AK4129]
■ System Clock for Output PORT
The output ports work in master mode and slave mode. The CM2-0 pins select the master/slave mode.
OMCLK/XTI
FSO with
CM2 CM1 CM0
Master / Slave
MCKO Output
FSO
Mode
pin
pin
pin
Input
X’tal
0
L
L
L
Master
256FSO
256FSO
44.1~96kHz
8k∼108kHz
1
L
L
H
Master
384FSO
384FSO
29.4~64kHz
8k∼96kHz
2
L
H
L
Master
512FSO
512FSO
22.05~48kHz
8k∼54kHz
3
L
H
H
Master
768FSO
768FSO
14.7~32kHz
8k∼48kHz
OMCLK Input
4
H
L
L
Slave
Not used (Note 24)
8k∼216kHz
Clock
5
H
L
H
Master
128FSO (Note 25)
128FSO
8k∼216kHz 88.2~192kHz
IMCLK Input
6
H
H
L
Slave(Bypass)
Not used (Note 24)
8k∼216kHz
Clock
7
H
H
H
Master(Bypass)
Note 24. Use for a clock input or connect to VSS2-5 pin. In Mode 4, the MCKO pin outputs “L” if the OMCLK/XTI pin is
connected to VSS2-5. When a clock is input to the OMCLK/XTI pin, the clock is through and output from the
MCKO pin. In Mode 6-7, OMCLK/XTI input is ignored internally.
Note 25. Output ports do not support TDM mode in this mode.
Table 3. Output PORT Master/Slave/ Bypass Mode Control (SPB pin = “L”)
In serial control mode (SPB pin = “H”), the BYPS bit selects SRC bypass mode and SRC mode.
The default value of the BYPS bit is “0” (SRC mode).
Mode
CM2
pin
CM1
pin
CM0
pin
BYPS
bit
Master / Slave
0
1
2
3
L
L
L
L
L
L
H
H
L
H
L
H
0
0
0
0
Master
Master
Master
Master
OMCLK/XTI
Input
256FSO
384FSO
512FSO
768FSO
4
H
L
L
0
Slave
Not used (Note 26)
MCKO
Output
256FSO
384FSO
512FSO
768FSO
OMCLK
Input
Clock
128FSO
8∼108kHz
8∼96kHz
8∼54kHz
8k~48kHz
FSO with
X’tal
44.1~96kHz
29.4~64kHz
22.05~48kHz
14.7~32kHz
8∼216kHz
-
FSO
5
H
L
H
0
Master
128FSO (Note 25)
8∼216kHz 88.2~192kHz
6
H
H
L
0
Slave (Bypass)
7
H
H
H
0
Master (Bypass)
8
L
L
L
1
Master (Bypass)
9
L
L
H
1
Master (Bypass)
IMCLK
10
L
H
L
1
Master (Bypass)
Input
Not used (Note 26)
8∼216kHz
11
L
H
H
1
Master (Bypass)
Clock
12
H
L
L
1
Slave (Bypass)
13
H
L
H
1
Master (Bypass)
14
H
H
L
1
Slave (Bypass)
15
H
H
H
1
Master (Bypass)
Note 26. Use for a clock input or connect to VSS2-5 pin. In Mode 4, the MCKO pin outputs “L” if the OMCLK/XTI pin is
connected to VSS2-5. When a clock is input to the OMCLK/XTI pin, the clock is through and output from the
MCKO pin. In Mode 6-15, OMCLK/XTI input is ignored internally.
Table 4. Output PORT Master/Slave/ Bypass Mode Control (SPB pin = “H”)
MS1173-E-02
2011/06
- 23 -
[AK4129]
(1) Master Mode
The OLRCK pin and OBICK pin are output pins in master mode. Master clock is supplied from the OMCLK/XTI pin. The
clock for the OMCLK/XTI pin can be generated by the following methods: Connect a crystal oscillator between the
OMCLK/XTI and XTO pins, or input a clock to the OMCLK/XTI pin. In bypass mode, the MCKO pin outputs IMCLK
data.
a.
X’tal
The OMCLK/XTI pin
is pulled down when
the PDN pin= “L”.
XTI
C
460kΩ (typ)
C
XTO
AK4129
Note: Refer to Table 5 for the capacitor and resistor values of the X’tal oscillator.
Figure 21. X’tal Mode
Nominal Frequency [MHz]
11.2896
12.288
24.576
Equivalent Series Resistance R1[Ω] max
60
External Capacitance C[pF] max
15
Table 5. Equivalent Series Resistor and External Capacitor for External X’tal Oscillator
In X’tal mode at 256FSO OMCLK input, FSO ranges from 44.1kHz to 96kHz.
In X’tal mode at 384FSO OMCLK input, FSO ranges from 29.4kHz to 64kHz.
In X’tal mode at 512FSO OMCLK input, FSO ranges from 22.05kHz to 48kHz.
In X’tal mode at 768FSO OMCLK input, FSO ranges from 14.7kHz to 32kHz.
In X’tal mode at 128FSO OMCLK input, FSO ranges from 88.2kHz to 192kHz.
b.
External Clcok
- Note: Do not input the clock over DVDD1-4.
XTI
External
Clock
460kΩ (typ)
XTO
AK4129
Figure 22. External Clock (OMCLK) mode
(2) Slave Mode
The OLRCK pin and OBICK pin are input pins in slave mode.
MS1173-E-02
2011/06
- 24 -
[AK4129]
(3) SRC Bypass Mode
SRC bypass mode can be set in Synchronous inputs mode (INAS pin = “L”). Asynchronous inputs mode (INAS pin = “H”)
does not supports SRC bypass mode, so that the data is not transferred correctly on SDTI1→SDTO1, SDTI2→SDTO2,
and SDTI3→SDTO3 lines. In Asynchronous inputs mode (INAS pin = “H”), the AK4129 should be used in SRC mode.
DITHER
SMT1
SMT0
SMSEMI
SMUTE
VSS2-5
DVDD1-4
INAS
DEM1
DEM0
IDIF2
IDIF1
IDIF0
When the AK4129 is in slave mode, SDTI1-3 data are input by the ILRCK1 and IBICK1 clocks in SRC bypass mode
(Table 2). The SDTI1-3 data are output from the OLRCK and OBICK pins in a format shown in Table 6 and Table 7.
IBICK and OBICK must be synchronized but the phase is not critical. ILRCK and OLRCK must be synchronized but the
phase is not critical.
OLRCK(I)
OBICK(I)
SRC1
Bypass
Input
Serial
Audio
I/F
IBICK1
ILRCK1
SDTI1
DEM
FIR
SRC
SMUTE
+
Dither
0.5 LSB
SRC
IBICK2
ILRCK2
SDTI2
DEM
FIR
SRC
SMUTE
SRC
Dither
+
DEM
FIR
SRC
ODIF1
ODIF0
Output
Serial
Audio
I/F
0.5 LSB
SDTO2
SRC3
Bypass
Input
Serial
Audio
I/F
IBICK3
ILRCK3
SDTI3
OBIT1
OBIT2
SRC2
Bypass
Input
Serial
Audio
I/F
SDTO1
SMUTE
SRC
Dither
+
SDTO3
0.5 LSB
Internal
OSC
IMCLK
PDN
PM1
PM2
UNLOCK
Bypass
uP
I/F
CAD0
X 'tal
Osc
.
SDA SCL XTO OMCLK/XTI
SPB
Clock
Div
CM2 CM1 CM0
MCKO
SRC
Internal
Regulator
REF
AVDD
VSS1
VD18
Figure 23. Bypass Mode in Slave Mode (Synchronous mode INAS pin = “L”)
MS1173-E-02
2011/06
- 25 -
[AK4129]
DITHER
SMT1
SMT0
SMSEMI
SMUTE
VSS2-5
DVDD1-4
INAS
DEM1
DEM0
IDIF2
IDIF1
IDIF0
When the AK4129 is in master mode, SDTI1-3 data are input by the ILRCK1 and IBICK1 clocks in SRC bypass mode
(Table 2). The SDTI1-3 output data are output by the ILRCK1 and IBICK1 clocks in a format shown in Table 6 and Table
7. The ILRCK1 clock bypasses the SRC and it is output from the OLRCK pin. The IBICK1 clock bypasses the SRC and it
is output from the OBICK pin.
OLRCK(O)
OBICK(O)
SRC1
Bypass
Input
Serial
Audio
I/F
IBICK1
ILRCK1
SDTI1
DEM
FIR
SRC
SMUTE
+
Dither
0.5 LSB
SRC
DEM
FIR
SRC
SMUTE
SRC
Dither
+
DEM
FIR
SRC
ODIF1
ODIF0
Output
Serial
Audio
I/F
0.5 LSB
SDTO2
SRC3
Bypass
Input
Serial
Audio
I/F
IBICK3
ILRCK3
SDTI3
OBIT1
OBIT2
SRC2
Bypass
Input
Serial
Audio
I/F
IBICK2
ILRCK2
SDTI2
SDTO1
SMUTE
SRC
Dither
+
SDTO3
0.5 LSB
Internal
OSC
IMCLK
PDN
PM1
PM2
UNLOCK
Bypass
uP
I/F
CAD0
X 'tal
Osc
.
SDA SCL XTO OMCLK/XTI
SPB
Clock
Div
CM2 CM1 CM0
MCKO
SRC
Internal
Regulator
REF
AVDD
VSS1
VD18
Figure 24. Bypass Mode in Master Mode (Synchronous mode INAS pin = “L”)
MS1173-E-02
2011/06
- 26 -
[AK4129]
■ Audio Interface Format for Output PORT
The ODIF1-0 pins and OBIT1-0 pins select the audio interface format for the output port. The audio data is MSB first, 2’s
complement format. The SDTO1-3 is clocked out on the falling edge of OBICK. Select the audio interface format for
output port when the PDN pin = “L”. If the AK4129 is in slave mode at bypass mode, IBICK1 and OBICK must be
synchronized but the phase is not critical. ILRCK1 and OLRCK must be synchronized but the phase is not critical. The
audio interface format of SDTO1, SDTO2 and SDTO3 are controlled together by ODIF1-0 pins, OBIT1-0 pins and TDM
pin. Output ports become TDM mode when the TDM pin = “H”. In TDM mode, the SDTI1 pin outputs serial data for
6channels and the SDTI2-3 pins output “L”.
Mode
0
1
2
3
4
5
6
7
Mode
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
TDM
pin
TDM pin
L
L
L
L
H
H
H
H
Master / Slave
setting
ODIF1 pin ODIF0 pin
SDTO1-3 Format
L
L
LSB justified
L
H
Reserved
H
L
MSB justified
H
H
I2S Compatible
L
L
Reserved
L
H
Reserved
H
L
TDM256 mode 24bit MSB justified
H
H
TDM256 mode 24bit I2S Compatible
Table 6. Output PORT Audio Interface Format 1
OBIT1
pin
OBIT0
pin
SDTO
1-3
L
L
H
H
L
L
H
H
L
H
L
H
L
H
L
H
16bit
18bit
20bit
24bit
16bit
18bit
20bit
24bit
Slave
(CM2-0 = “HLL”
or “HHL”)
*
*
Master
(Not CM2-0 =
“HLL”/“HHL”)
*
*
Slave
(CM2-0 = “HLL”
or “HHL”)
L
Master
(Not CM2-0 =
“HLL”/“HHL”)
OBICK Frequency
LSB
MSB justified,
justified
I2S
≥ 32FSO
≥ 36FSO
64FSO
≥ 40FSO
≥ 48FSO
OLRC
K
OBICK
Input
Input
Output
Output
64FSO
TDM256
mode
24bit
Input
Input
256FSO
TDM256
mode
24bit
Output
Output
256FSO
H
Table 7. Output PORT Audio Interface Format 2
(* The data length for 1channel is 24bit fixed in TDM mode. The OBIT1-0 pin settings are ignored. Connect these pins to
VSS2-5.)
MS1173-E-02
2011/06
- 27 -
[AK4129]
OLRCK
0 1
8 9 10 11 12 13 14 15 16 17
20 21 22 23
29 30 31 0 1
8 9 10 11 12 13 14 15 16 17
20 21 22 23
29 30 31 0 1 2
OBICK(64fs)
15 14
11 10 9 8
2 1 0
15 14
11 10 9 8
2 1 0
17 16 15 14
11 10 9 8
2 1 0
17 16 15 14
11 10 9 8
2 1 0
19 18 17 16 15 14
11 10 9 8
2 1 0
19 18 17 16 15 14
11 10 9 8
2 1 0
11 10 9 8
2 1 0
23 22 21 20 19 18 17 16 15 14
11 10 9 8
2 1 0
SDTO(O)
15:MSB, 0:LSB
SDTO(O)
17:MSB, 0:LSB
SDTO(O)
19:MSB, 0:LSB
SDTO(O)
23 22 21 20 19 18 17 16 15 14
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 25. Stereo Mode LSB justified Timing
OLRCK
0 1 2 3 4
13 14 15 16 17 18 19 20 21 22 23 24
31 0 1 2 3 4
13 14 15 16 17 18 19 20 21 22 23 24
31 0 1 2
OBICK(64fs)
SDTO(O)
15 14 13 12
2 1 0
15 14 13 12
2 1 0
15 14
17 16 15 14
4 3 2 1 0
17 16
19 18 17 16
6 5 4 3 2 1 0
19 18
23 22 21 20
10 9 8 7 6 5 4 3 2 1 0
23 22
15:MSB, 0:LSB
SDTO(O)
17 16 15 14
4 3 2 1 0
17:MSB, 0:LSB
SDTO(O)
19 18 17 16
6 5 4 3 2 1 0
19:MSB, 0:LSB
SDTO(O)
23 22 21 20
10 9 8 7 6 5 4 3 2 1 0
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 26. Stereo Mode MSB Justified Timing
OLRCK
0 1 2 3 4
14 15 16 17 18 19 20 21 22 23 24
0 1 2 3 4
14 15 16 17 18 19 20 21 22 23 24
31 0 1 2
OBICK(64fs)
SDTO(O)
15 14 13 12
2 1 0
15 14 13 12
2 1 0
15
17 16 15 14
4 3 2 1 0
17
19 18 17 16
6 5 4 3 2 1 0
19
23 22 21 20
10 9 8 7 6 5 4 3 2 1 0
23
15:MSB, 0:LSB
SDTO(O)
17 16 15 14
4 3 2 1 0
17:MSB, 0:LSB
SDTO(O)
19 18 17 16
6 5 4 3 2 1 0
19:MSB, 0:LSB
SDTO(O)
23 22 21 20
10 9 8 7 6 5 4 3 2 1 0
23:MSB, 0:LSB
Lch Data
Rch Data
2
Figure 27. Stereo Mode I S Compatible Timing
Note: SDTO is identified as SDTO1, SDTO2 and SDTO3.
MS1173-E-02
2011/06
- 28 -
[AK4129]
256 OBICK
1/ 8FSO
OLRCK(O)
OBICK(O) (256FSO)
SDTO 1 (O)
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
L1
R1
L2
R2
L3
R3
32OBICK
32OBICK
32OBICK
32OBICK
32OBICK
32OBICK
Figure 28. TDM 256 mode 24bit MSB justified Timing at Master Mode. (SDTO2-3: “L” outputs)
256 OBICK
min. 1/ 256FSO
OLRCK(I)
OBICK(I) (256FSO)
SDTO 1 (O)
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
L1
R1
L2
R2
L3
R3
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
23 22
Figure 29. TDM 256 mode 24bit MSB justified Timing at Slave Mode. (SDTO2-3: “L” outputs)
256 OBICK
1/8FSO
OLRCK(O)
OBICK (O: 256FSO)
SDTO 1 (O)
23
0
23
0
23
0
23
0
23
0
23
0
L1
R1
L2
R2
L3
R3
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
23
Figure 30. TDM 256 mode 24bit I2S Compatible Timing at Master Mode (SDTO2-3: “L” outputs)
256 OBICK
min. 1/ 256FSO
OLRCK(I)
OBICK ( I: 256FSO)
SDTO 1 (O)
23
0
23
0
23
0
23
0
23
0
23
0
L1
R1
L2
R2
L3
R3
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
32 OBICK
23
Figure 31. TDM 256 mode 24bit I2S Compatible Timing at Slave Mode (SDTO2-3: “L” outputs)
MS1173-E-02
2011/06
- 29 -
[AK4129]
■ 6/4channel Mode
The AK4129 has AK4126 compatible 6-channel mode, AK4129 original 6-channel mode and 4-channel modes. When the
PM2/1 pins are set to “L/L”, the AK4129 becomes AK4126 compatible 6-channel mode and six channels (SDTI1Æ
SDTO1, SDTI2 Æ SDTO2 and SDTI3 Æ SDTO3) are powered up. When the PM2/1 pins are set to “L/H”, the AK4129
becomes 4-channel mode and four channels (SDTI1Æ SDTO1 and SDTI2 Æ SDTO2) are powered up, and the other two
channels (SDTI3 Æ SDTO3) are powered down (“L” output). When the PM2/1 pins are set to “H/L”, the AK4129
becomes original 6-channel mode and six channels (SDTI1Æ SDTO1, SDTI2 Æ SDTO2 and SDTI3 Æ SDTO3) are
powered up. In AK4126 compatible 6-channel mode and 4-channel mode, the X’tal oscillator circuit and the MCKO output
are powered down and the XTO pin and MCKO pin output Hi-z.
PM2
pin
L
L
L
L
H
PM1
pin
L
L
H
H
L
PDN
pin
L
H
L
H
L
H
L
H
H
H
H
H
L
H
Mode
X’tal Oscillator
6-channel mode
(AK4126 compatible)
Power-down
4-channel mode
Power-down
6-channel mode
(Original mode)
Not available
Power-down
Normal
operation
-
XTO
pin
XTI pin
Pull down to VSS2-5 (note)
Input
Pull down to VSS2-5 (note)
Input
Pull down to VSS2-5 (note)
MCKO
pin
Hi-z
Hi-z
Hi-z
Hi-z
L
Normal
Input
Output
operation
Note: Pull down (460kΩ typ.) to VSS2-5.
Table 8. Channel Mode Setting
■ Soft Mute Operation
1. Manual Mode
The soft mute operation is performed in the digital domain of the SRC output. SRC1-3 soft mutes are controlled together by
the SMUTE pin in parallel control mode (SPB pin = “L”). In serial control mode (SPB pin = “H”), setting of the SMUTE
pin is ignored. SRC1 reflects SMUTE1 bit setting, SRC2 reflects SMUTE2 bit setting, and SRC3 reflects SMUTE3 bit
setting.
When the SMUTE pin goes “H” or SMUTE1-3 bits becomes “1”, all the outputs data are attenuated by −∞ during 1024
OLRCK cycles (@ SMT1 pin = “L” and SMT0 pin = “L”). When the SMUTE pin goes “L” or SMUTE1-3 bits becomes
“0”the mute is cancelled and the output attenuation gradually changes to 0dB during 1024 OLRCK cycles (@ SMT1 pin =
“L” and SMT0 pin = “L”). If the soft mute is cancelled before attenuating to -∞, the attenuation is discontinued and
returned to 0dB by the same cycles. The soft mute is effective for changing the signal source without stopping the signal
transmission. Soft mute cycle is set by SMT1-0 pins. SMT1-0 pins must not be changed during soft mute transition.
SMT1pin
L
L
H
H
SMT0 pin
Period
FSO=48kHz FSO=96kHz
L
1024/fso
21.3ms
10.7ms
H
2048/fso
42.7ms
21.3ms
L
4096/fso
85.3ms
42.7ms
H
8192/fso
170.7ms
85.3ms
Table 9. Soft Mute Cycle Setting (Parallel Mode)
MS1173-E-02
FSO=192kHz
5.3ms
10.7ms
21.3ms
42.7ms
2011/06
- 30 -
[AK4129]
SM U T E p in ,
SM U T E1 -3 b it
(1 )
0dB
(1 )
(2 )
Atte nu a tio n
-∞
All “0” code
SD T O
Note: SDTO is identified as SDTO1, SDTO2 and SDTO3.
(1) The soft mute cycle is selected by SMT1-0 pins. (Table 9) The output data is attenuated by −∞ during the soft mute
cycle.
(2) If the soft mute is cancelled before attenuating to −∞, the attenuation is discontinued and returned to 0dB by the same
clock cycles.
Figure 32. Soft Mute Function (Manual Mode) 2. Semi-Auto Mode
When power down of the AK4129 is released (PDN pin = “L” → “H”) with the SMSEMI pin= “H”, the AK4129 enters
semi-auto mode. In this mode, soft mute is cancelled automatically 4410/FSO after a rising edge of PDN (100ms
@FSO=44.1kHz). The soft mute is ON after releasing power down if the SMUTE pin = “H”. The SMSEMI pin must be set
during the PDN pin = “L”.
PD N pi n
“L ”
S M U T E p in
D o n ’t ca re
(1 )
0 dB
Atte n u atio n
“L ”
(2 )
4 41 0 /fso
-∞
SD T O
All “0” c od e
Note: SDTO is identified as SDTO1, SDTO2 and SDTO3.
(1) The output data is attenuated by −∞ during the soft mute cycle (Table 9)
(2) When it is 0dB by a soft mute release after 4410/FSO, it is able to mute or release the mute by the soft mute cycle in
Table 9.
Figure 33. Soft Mute Function (Semi-Auto Mode)
MS1173-E-02
2011/06
- 31 -
[AK4129]
■ Dither
The AK4129 includes a dither circuit. The dither circuit adds a dither signal after the lowest bit of all the output data set by
the OBIT1-0 pins when the DITHER pin = “H”, regardless of SRC and SRC bypass modes. If the output bit is 24bit length
in SRC bypass mode, the output code does not change by the DITHER pin setting.
■ De-emphasis Filter
The AK4129 includes a digital de-emphasis filter (tc = 50/15μs) by an IIR filter. This filter corresponds to three
frequencies (32kHz, 44.1kHz and 48kHz). In parallel control mode (SPB pin = “L”), de-emphasis setting of SRC1-3 are
controlled together by DEM1-0 pins. In serial control mode (PSB pin = “H”), the setting of DEM1-0 pins is ignored. SRC1
reflects the DEM[11:10] bits setting, SRC2 reflects the DEM[21:20] bits setting and SRC3 reflects the DEM[31:30] bits
setting.
DEM11pin
DEM10 pin Mode(SDTI1-3)
L
L
44.1kHz
L
H
OFF
H
L
48kHz
H
H
32kHz
Table 10. De-emphasis Filter Setting (Parallel Control Mode (SPB pin= “L”))
DEM11bit
DEM10 bit
Mode(SDTI1)
L
L
44.1kHz
L
H
OFF
H
L
48kHz
H
H
32kHz
Table 11. De-emphasis Filter Setting for SDTI1 (Serial Control Mode (SPB pin = “H”))
DEM21 bit
DEM20 bit
Mode(SDTI2)
L
L
44.1kHz
L
H
OFF
H
L
48kHz
H
H
32kHz
Table 12. De-emphasis Filter Setting for SDTI2 (Serial Control Mode (SPB pin= “H”))
DEM31 bit
DEM30 bit
Mode(SDTI3)
L
L
44.1kHz
L
H
OFF
H
L
48kHz
H
H
32kHz
Table 13. De-emphasis Filter Setting for SDTI3 (Serial Control Mode (SPB pin = “H”))
MS1173-E-02
2011/06
- 32 -
[AK4129]
■ Regulator
The AK4129 has an internal regulator which suppresses the voltage to 1.8V from DVDD1-4. The generated 1.8V power is
used as power supply for internal circuit. When over-current is flowed to the regulator output, over-current detection circuit
works. When over-voltage is flowed to the regulator output, over-voltage detection circuit works. The regulator block is
powered-down and the AK4129 becomes reset state when over-current detection circuit or over-voltage detection circuit is
operated. The AK4129 does not return to normal operation without a reset by the PDN pin when these detection circuits are
worked. When over-current or over-voltage is detected, the PDN pin should be brought into “L” at once, and should be set
to “H” again to recover normal operation.
The UNLOCK pin indicate the internal status of the device, and outputs “L” in SRC normal operation, and outputs “H”
when over-current or over-voltage are detected.
■ System Reset
Bringing the PDN pin = “L” sets the AK4129 power-down mode and initializes the digital filters. The AK4129 should be
reset once by bringing the PDN pin = “L” upon power-up. When PDN pin = “L”, the SDTO1-3 output is “L”. It takes 23ms
(max) for SDTO output enable after power-down state is released by a clock input. Until then, the SDTO1-3 outputs “L”.
The internal SRC circuit is powered-up on an edge of ILRCK1-3 after a power-up time period of the internal regulator.
(SDTO is identified as SDTO1, SDTO2 and SDTO3. SDTI is identified as SDTI1, SDTI2 and SDTI3.)
Case 1
External clocks
(Input port)
Don’t care
Input Clocks 1
Input Clocks 2
Don’t care
SDTI
Don’t care
Input Data 1
Input Data 2
Don’t care
External clocks
(Output port)
Don’t care
Output Clocks 1
Output Clocks 2
Don’t care
PDN
23ms(max)
(Internal state) Power-down
SDTO3
“0” data
SDTO2
“0” data
SDTO1
“0” data
(1)
23ms(max)
Normal
operation
PD
Normal data
(1)
Normal
operation
Power-down
“0” data
Normal data
“0” data
Normal data
“0” data
Normal data
“0” data
Normal data
“0” data
Normal data
“0” data
UNLOCK
Figure 34. System Reset 1
MS1173-E-02
2011/06
- 33 -
[AK4129]
Case 2
External clocks
(Input port)
(No Clock)
SDTI
External clocks
(Output port)
Input Clocks
Don’t care
(Don’t care)
Input Data
Don’t care
(Don’t care)
Output Clocks
Don’t care
PDN
21ms(max)
(Internal state) Power-down
I nt ernal Ci rc uit
Power-up Time
ILRCK1-4
Input wait
(2)
Normal
operation
Power-down
SDTO3
“0” data
Normal data
“0” data
SDTO2
“0” data
Normal data
“0” data
SDTO1
“0” data
Normal data
“0” data
UNLOCK
Figure 35. System Reset 2
Note 27. SPB, CM2-0, INAS, PM2-1, OBIT1-0, TDM, ODIF1-0, IDIF2-0 and CAD0 pin must be changed when the PDN
pin= “L”.
Note 28. The UNLOCK pin outputs “H” when the PDN pin= “L”. SRC data is output from SDTO1-3 pins, which
corresponds to the each sampling frequency ratio detected SRC, after a rising edge “↑” of PDN if the internal
regulator is in normal operation.
Note 29. (1) is the total time of “Internal circuit power-up + FSO/FSI ratio detection + Clock detection + Internal circuit
group delay”.
Note 30. (2) is the total time of “FSO/FSI ratio detection + Clock detection + Internal circuit group delay”.
MS1173-E-02
2011/06
- 34 -
[AK4129]
■ Internal Reset Function for Clock Change
Clock change timing is shown in Figure 36 and Figure 37. SDTO is identified as SDTO1, SDTO2 and SDTO3. When
changing the clock, the AK4129 should be reset by the PDN pin in parallel control mode and it should be reset by the PDN
pin or RSTN bit in serial control mode (Figure 36). SDTO means SDTO1-3 in this figure.
External clocks
(Input port
or Output port)
Clocks 1
Clocks 2
Don’t care
PDN pin
max 23ms
(Internal state) Normal operation Power-down
SDTO
Att.Level
Normal operation
Note31
Normal data
SMUTE (Note32,
recommended)
(3)
Normal data
1024/FSO
1024/F SO
0dB
- ∞dB
Note 31. The data on SDTO may cause a clicking noise. To prevent this, set “0” to the SDTI more than 1024/fs (GD) before
the PDN pin changes to “L”. It makes the data on SDTO remain as “0”.
Note 32. SMUTE can also remove the clicking noise. (Note 31)
Note 33. (3) is the total time of “Internal circuit power-up + FSO/FSI ratio detection + Internal circuit group delay”.
Figure 36. Clock Change Sequence in Parallel Control Mode (SPB pin = “L”)
External clocks
(Input port or Output port)
Clocks 1
Don’t care
Clocks 2
RSTN bit
(Internal state)
Normal operation
SDTO
Normal data
Reset (Note 28)
Note 34
(4)
Normal operation
Normal data
1024/F SO
SMUTE (Note35,recommended)
1024/FSO
Att.Level
0dB
-∞dB
Note 34. The data on SDTO may cause a clicking noise. To prevent this, set “0” to the SDTI from GD before the PDN pin
changes to “L”. It makes the data on SDTO remain as “0”.
Note 35. SMUTE can also remove the clicking noise. (Note 34)
Note 36. The digital block except serial control interface and registers is powered-down. The internal oscillator and
regulator are not powered-down.
Note 37. (4) is the total time of “0.5/FSI+8/FSI(O)+156/FSO” or “1.5/FSI+8/FSI(O)+156/FSO”. (FSI(O) is lower
frequency between FSI and FSO)
Figure 37. Clock Change Sequence in Serial Control Mode (SPB pin = “H”)
MS1173-E-02
2011/06
- 35 -
[AK4129]
1. When the frequency of ILRCKx (x=1, 2, 3) at input port is changed without a reset by the PDN pin or RSTN bit.
When the difference of internal oscillator (min. 59.4 MHz, typ. 73.5 MHz) clock number in one ILRCKx cycle
between before an ILRCKx frequency change (FSO/FSI ratio is stabilized) and after the change is more than ±100
for 8cycles, an internal reset is made automatically and sampling frequency ratio detection is executed again.
SDTOx outputs “L” when the internal reset is made, and SRC data is output after “0.5/FSI+8/FSI(O)+156/FSO” or
“1.5/FSI+8/FSI(O)+156/FSO” (FSI(O) is lower frequency between FSI and FSO).
If the difference of internal oscillator clock number in one ILRCKx cycle between before an ILRCKx frequency
change and after the change is less than ±100 or more than ±100 but shorter than 8cycles, the internal reset is not
executed. In both cases; when ILRCKx frequency is changed immediately without transition time or with transition
time which is not long enough for an internal reset, it takes 5148/FSO (max. 643.5ms @FSO=8kHz) (Note 38)to
output normal SRC data. Distorted data may be output until normal SRC output.
When ILRCKx is stopped, an internal reset is executed automatically. It takes “0.5/FSI+8/FSI(O)+156/FSO” or
“1.5/FSI+8/FSI(O)+156/FSO” (FSI(O) is lower frequency between FSI and FSO) [s] to output normal SRC data
after ILRCKx is input again.
2. When the frequency of OLRCK at output port is changed without a reset by the PDN pin or RSTN bit.
When the difference of internal oscillator clock number in one OLRCK cycle between before an OLRCK frequency
change (FSO/FSI ratio is stabilized) and after the change is more than ±100 for 8cycles, an internal reset is made
automatically and sampling frequency ratio detection is executed again. SDTOx (x=1, 2, 3) outputs “L” when the
internal reset is made, and SRC data is output after “0.5/FSI+8/FSI(O)+156/FSO” or
“1.5/FSI+8/FSI(O)+156/FSO” (FSI(O) is lower frequency between FSI and FSO).
If the difference of internal oscillator clock number in one OLRCK cycle between before an OLRCK frequency
change and after the change is less than ±100 or more than ±100 but shorter than 8cycles, the internal reset is not
executed. It takes 5148/FSO (max. 643.5ms @FSO=8kHz) (Note 38) to output normal SRC data. Distorted data
may be output until normal SRC output.
When OLRCK is stopped, an internal reset is executed automatically. It takes “0.5/FSI+8/FSI(O)+156/FSO” or
“1.5/FSI+8/FSI(O)+156/FSO” (FSI(O) is lower frequency between FSI and FSO) [s] to output normal SRC data
after ILRCKx is input again.
Note 38. When FSO=8kHz and FSO/FSI ratio is changed from 1/6 to 1/5.99. It is 160.9ms when FSO=32kHz and FSO/fSI
ratio is changed from 1/6 to 1/5.99.
MS1173-E-02
2011/06
- 36 -
[AK4129]
■ Internal Status Pin
The UNLOCK pin indicates internal status of the device. This pin outputs “H” when the PDN pin = “L”. SRC data is output
from SDTO1-3 pins, which corresponds to the each sampling frequency ratio detected SRC, after a rising edge “↑” of PDN
if the internal regulator is in normal operation.
When PM2/1 pins = “H/L”, in AK4129 original 6-channel mode, the UNLOCK pin only outputs “H”. When PM2/1 pins =
“L/L”, in AK4126 compatible 6-channel, the UNLOCK pin outputs “L” when sampling frequency ratio detection is
completed at all SRC’s (SRC1-3). The UNLOCK pin keeps outputting “H” if there is any SRC which does not finished
sampling frequency ratio detection.
In 4-channel mode, the UNLOCK pin outputs “L” when sampling frequency ratio detection is completed at SRC1-2. It
keeps outputting “H” if there is any SRC which does not finish sampling frequency ratio detection.
When over-current/voltage is flowed at the internal regulator, the UNLCOK pin outputs “H”. An OR’ed result of the flags
between over-current/voltage detection at the internal regulator and SRC sampling frequency detection complete is output
from this pin.
Over-Current/Voltage Limit Flag
(“L” Normal, “H” Over-Current/Voltage detect)
SRC Sampling Frequency Ratio Complete Flag
UNLOCK pin
Figure 38. Internal Flags and UNLOCK pin Output
In parallel control mode, if the AK4129 is set in SRC bypass mode by CM2-0 pins during the PDN pin = “L” and
powered-up, the UNLOCK pin outputs “L” after the power-up time of the internal regulator (max. 1.4ms) from a rising
edge “↑” of the PDN pin. In serial control mode, if BYPS bit is set to “1”while RSTN bit = “0”, the UNLOCK pin
immediately outputs “L” after the register writing.
MS1173-E-02
2011/06
- 37 -
[AK4129]
■ Serial Control Interface
The AK4129 supports fast-mode I2C-bus system (max: 400kHz). Pull-up resistors at SDA and SCL pins should be
connected to (DVDD1-4 + 0.3)V or less voltage.
1. Data transfer
All commands are preceded by a START condition. After the START condition, a slave address is sent. After the AK4129
recognizes the START condition, the device interfaced to the bus waits of the slave address to be transmitted over the SDA
line. If the transmitted slave address matches an address for one of the devices, the designated slave device pulls the SDA
line to LOW (ACKNOWLEDGE). The data transfer is always terminated by a STOP condition generated by the master
device.
1-1. Data validity
The data on the SDA line must be stable during a HIGH period of the clock. The HIGH or LOW state of the data line can
only be changed when the clock signal on the SCL line is LOW except for the START and the STOP condition.
SCL
SDA
DATA LINE
STABLE :
DATA VALID
CHANGE
OF DATA
ALLOWED
Figure 39. Data Transfer
1-2. START and STOP condition
A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition. All sequences start from the
START condition.
A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition. All sequences end by the
STOP condition.
S
SCL
SDA
START CONDITION
STOP CONDITION
Figure 40. START and STOP conditions
MS1173-E-02
2011/06
- 38 -
[AK4129]
1-3. ACKNOWLEDGE
ACKNOWLEDGE is a software convention used to indicate successful data transfers. The transmitter will release the SDA
line (HIGH) after transmitting eight bits. The receiver must pull down the SDA line during the acknowledge clock pulse so
that that it remains stable “L” during “H” period of this clock pulse. The AK4129 generates an acknowledge after each byte
is received.
In read mode, the slave, the AK4129 transmits eight bits of data, release the SDA line and monitor the line for an
acknowledge. If an acknowledge is detected and no STOP condition is generated by the master, the slave will continue
transmitting data. If an acknowledge is not detected, the slave will terminate further data transmissions and await the STOP
condition.
Clock pulse
for acknowledge
SCL FROM
MASTER
1
8
9
DATA
OUTPUT BY
TRANSMITTER
not acknowledge
DATA
OUTPUT BY
RECEIVER
START
CONDITION
acknowledge
Figure 41. Acknowledge on the I2C-bus
1-4. FIRST BYTE
The first byte, which includes seven bits of slave address and one bit of R/W bit, is sent after a START condition. If the
transmitted slave address matches an address for one of the device, the receiver who has been addressed pulls down the
SDA line.
The first six bits of the slave address are fixed as “001001”. The next (seventh) bit is CAD0 (device address bits). It is “0”
when the CAD0 pin = “L”, and “1” when the CAD pin = “H”. This bit identifies the specific device on the bus. When the
slave address is input, the matched device generates an acknowledge and executes a command. The eighth bit (R/W bit) of
the first byte defines whether the master requests a write or read condition. A “1” indicates that the read operation is to be
executed. A “0” indicates that the write operation is to be executed.
0
0
1
0
0
1
CAD0
R/W
Figure 42. The First Byte
MS1173-E-02
2011/06
- 39 -
[AK4129]
2. WRITE Operations
Set R/W bit = “0” for the WRITE operation of the AK4129.
After receipt of a start condition and the first byte, the AK4129 generates an acknowledge, and awaits the second byte
(register address). The second byte consists of the address for control registers of AK4129. The format is MSB first, and
first 6bits must be fixed to “0”.
0
0
0
0
0
0
A1
A0
(*: Don’t care)
Figure 43. The Second Byte
After receipt the second byte, the AK4129 generates an acknowledge, and awaits the third byte. Those data after the second
byte contain control data. The format is MSB first, 8bits.
D7
D6
D5
D4
D3
D2
D1
D0
Figure 44. Byte structure after the second byte
The AK4129 is capable of more than one byte write operation by one sequence.
After receipt of the third byte, the AK4129 generates an acknowledge, and awaits the next data again. The master can
transmit more than one word instead of terminating the write cycle after the first data word is transferred. After the receipt
of each data, the internal address counter is incremented by one, and the next data is taken into next address automatically.
If the address exceeds 03H prior to generating a stop condition, the address counter will “roll over” to 00H and the previous
data will be overwritten.
S
T
A
R
T
SDA
Slave
Address
Register
Address(n)
Data(n)
S
T
Data(n+x) O
P
Data(n+1)
P
S
A
C
K
A
C
K
A
C
K
A
C
K
Figure 45. WRITE Operation
MS1173-E-02
2011/06
- 40 -
[AK4129]
3. READ Operations
Set R/W bit = “1” for the READ operation of the AK4129.
After transmission of the data, the master can read next address’s data by generating an acknowledge instead of terminating
the write cycle after the receipt of the first data word. After the receipt of each data, the internal address counter is
incremented by one, and the next data is taken into next address automatically. If the address exceed 03H prior to
generating a stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten.
The AK4129 supports two basic read operations: CURRENT ADDRESS READ and RANDOM READ.
3-1. CURRENT ADDRESS READ
The AK4129 contains an internal address counter that maintains the address of the last word accessed, incremented by one.
Therefore, if the last access (either a read or write) was to address “n”, the next CURRENT READ operation would access
data from the address “n+1”.
After receipt of the slave address with R/W bit set to “1”, the AK4129 generates an acknowledge, transmits 1byte data
which address is set by the internal address counter and increments the internal address counter by 1. If the master does not
generate an acknowledge but generate the stop condition, the AK4129 discontinues transmission.
S
T
A
R
T
SDA
Slave
Address
Data(n)
Data(n+1)
S
Data(n+x) T
O
P
Data(n+2)
P
S
A
C
K
A
C
K
A
C
K
A
C
K
Figure 46. CURRENT ADDRESS READ
3-2. RANDOM READ
Random read operation allows the master to access any memory location at random. Prior to issuing the slave address with
the R/W bit set to “1”, the master must first perform a “dummy” write operation.
The master issues a start condition, slave address (R/W=“0”) and then the register address to read. After the register
address’s acknowledge, the master immediately reissues the start condition and the slave address with the R/W bit set to
“1”. Then the AK4129 generates an acknowledge, 1byte data and increments the internal address counter by one. If the
master does not generate an acknowledge but generate the stop condition, the AK4129 discontinues transmission.
S
T
A
R
T
SDA
S
T
A
R
T
Word
Address(n)
Slave
Address
S
Slave
Address
Data(n)
S
Data(n+x) T
O
P
Data(n+1)
P
S
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Figure 47. RANDOM READ
MS1173-E-02
2011/06
- 41 -
[AK4129]
■ Register Map
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
00H
Reset & Mute
0
SMUTE3 SMUTE2 SMUTE1
0
BYPS
0
RSTN
01H
De-emphasis
0
1
DEM31 DEM30 DEM21 DEM20 DEM11
DEM10
02H Input Audio Data Format 1
0
IDIF22 IDIF21 IDIF20
0
IDIF12 IDIF11
IDIF10
03H Input Audio Data Format 2
0
0
0
0
0
IDIF32 IDIF31
IDIF30
Note 39. All register values are initialized by the PDN pin = “L”.
Note 40. Writing to the address 00H ~ 03H are inhabited. The addresses defined as 0 must contain “0” data. BYPS bit and
IDIF12-10, 22-20, 32-30 bits should be written when RSTN bit = “0”.
Note 41. I2C access becomes valid after 1.4ms (max) from PDN pin “↑”.
■ Register Definitions
Addr Register Name
00H
Reset & Mute
R/W
Default
D7
0
RD
0
D6
SMUTE3
R/W
0
D5
SMUTE2
R/W
0
D4
SMUTE1
R/W
0
D3
0
RD
0
D2
BYPS
R/W
0
D1
0
RD
0
D0
RSTN
R/W
1
RSTN: Digital Reset Control
0: Reset
1: Reset Release (default)
When this bit is set to “0”, some digital blocks of the AK4129 are powered-down. In this case SRC1-3
can not operate. Control register settings are not initialized because I²C serial control interface and
control register blocks are not powered-down. Control register writings are available. The internal
oscillator for the clocks, the regulator and the reference voltage generation circuit are not powered-down.
BYPS: Bypass Mode Control
0: SRC Mode (default)
1: SRC Bypass Mode
Refer to Table 3.
SMUTE1: SRC1 Soft Mute Control
0: Soft Mute Release (default)
1: Soft Mute
In serial control mode (SPB pin= “H”), the SMUTE pin setting is ignored. SRC1 reflects the SMUTE1
bit setting.
SMUTE2: SRC2 Soft Mute Control
0: Soft Mute Release (default)
1: Soft Mute
In serial control mode (SPB pin= “H”), the SMUTE pin setting is ignored. SRC2 reflects the SMUTE2
bit setting.
SMUTE3: SRC3 Soft Mute Control
0: Soft Mute Release (default)
1: Soft Mute
In serial control mode (SPB pin= “H”), the SMUTE pin setting is ignored. SRC3 reflects the SMUTE3
bit setting.
MS1173-E-02
2011/06
- 42 -
[AK4129]
Addr Register Name
01H
De-emphasis
R/W
Default
D7
0
RD
0
D6
1
RD
1
D5
DEM31
R/W
0
D4
DEM30
R/W
1
D3
DEM21
R/W
0
D2
DEM20
R/W
1
D1
DEM11
R/W
0
D0
DEM10
R/W
1
DEM11/10: SRC1 De-emphasis Control
Default: “01” De-emphasis=OFF
DEM21/20: SRC2 De-emphasis Control
Default: “01” De-emphasis=OFF
DEM31/30: SRC3 De-emphasis Control
Default: “01” De-emphasis=OFF
In serial control mode (SPB pin= “H”), the setting of DEM1-0 pins is ignored. The DEM[11:10] bits setting is
reflected to SRC1, the DEM[21:20] bits setting is reflected to SRC2 and the DEM[31:30] bits setting is reflected
to SRC3.
Addr
Register Name
02H
Input Audio Data Format 1
R/W
Default
Addr
Register Name
03H
Input Audio Data Format 2
R/W
Default
D7
D6
D5
D4
D3
D2
D1
D0
0
IDIF22
IDIF21
IDIF20
0
IDIF12
IDIF11
IDIF10
RD
0
R/W
0
R/W
0
R/W
0
RD
0
R/W
0
R/W
0
R/W
0
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
IDIF32
IDIF31
IDIF30
RD
0
RD
0
RD
0
RD
0
RD
0
R/W
0
R/W
0
R/W
0
IDIF12/11/10: SRC1 Audio Data Interface Mode Select for Input Ports
Default: “000” Mode 0 (Refer Table 2)
IDIF22/21/20: SRC2 Audio Data Interface Mode Select for Input Ports
Default: “000” Mode 0 (Refer Table 2)
IDIF32/31/30: SRC3 Audio Data Interface Mode Select for Input Ports
Default: “000” Mode 0 (Refer Table 2)
In serial control mode (SPB pin = “H”), the setting of IDIF2-0 pins is ignored. The IDIF[12:10] bits setting is
reflected to SRC1, the IDIF[22:20] bits setting is reflected to SRC2 and the IDIF[32:30] bits setting is reflected
to SRC3.
MS1173-E-02
2011/06
- 43 -
[AK4129]
SYSTEM DESIGN
Figure 48 and Figure 49 shows the system connection diagram. An evaluation board is available which demonstrates
application circuits, the optimum layout, power supply arrangements and measurement results.
• Parallel Control Mode (SPB pin = “L”).
•Synchronous Mode (INAS pin = “L”).
• OMCLK/XTI Input = X’tal mode
• Input PORT: Slave mode, IBICK1 lock mode (64FSI), 24 bit MSB justified
• Output PORT: Slave mode, 24 bit MSB justified
• Dither = OFF, DEM=OFF, PM2/1 pin= “H/L” (6ch original mode)
C1= 0.1μF
C2=10μF
C3=1μF± 30%
3.3V
+
C2
C1
C
+
C2
C3
FSI
64FSI
54
53
52
51
50
49
CAD0
TST0
MCKO
55
DVDD
56
TST1
VD18
AVDD
57
VSS5
VSS1
58
TST2
TST3
59
SMSEMI
60
SCL
+
61
SPB
62
SDA
63
ILRCK2
C1
64
1 IBICK2
XTO 48
2 IMCLK
OMCLK/XTI 47
FSO
3 ILRCK1
OLRCK 46
4 IBICK1
OBICK 45
5 DVDD
DVDD 44
6 VSS2
VSS4 43
7 TST4
TST7 42
64FSO
C1
DSP1
C1
8 SDTI1
SDTO1 41
Top View
9 SDTI2
DSP2
SDTO2 40
10 SDTI3
SDTO3 39
11 IDIF0
ODIF0 38
12 IDIF1
ODIF1 37
13 IDIF2
CM0 36
14 ILRCK3
CM1 35
UNLOCK
DVDD
VSS3
SMUTE
DITHER
PDN
SMT0
SMT1
DEM0
DEM1
PM1
OBIT0
OBIT1
PM2
TDM 33
INAS
CM2 34
16 TST5
TST6
15 IBICK3
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
C1
+
C2
uP
Notes:
- All digital input pins should be not left floating.
- VSS1 -5 must be connected to the same ground plane.
- Connect a 1μF (± 30%; including temperature characteristics) capacitor between the VD18 pin and DVSS. When
this capacitor is polarized, the positive polarity pin should be connected to the VD18 pin.
- Refer to Table 5 for the equivalent series resistance R1 and capacitance C values of the X’tal oscillator.
Figure 48. Typical Connection Diagram (Parallel Control Mode)
MS1173-E-02
2011/06
- 44 -
[AK4129]
• Serial Control Mode (SPB pin = “H”).
•Asynchronous Inputs Mode (INAS pin = “H”).
• OMCLK/XTI Input= 256FSO, X’tal
• Input PORT: Slave mode, IBICK1~3 lock mode (64FSI)
Input Audio Interface Format can be set by registers.
• Output PORT: Master mode, 24 bit MSB justified.
• Dither = OFF, De-emphasis filter can be set by registers. PM2/1 pin= “H/L” (6ch original mode)
C1= 0.1μF
C2=10μF
C3=1μF± 30%
3.3V
+
C2
C1
C
+
C
C2
C3
56
55
TST3
VD18
AVDD
SPB
SDA
SCL
TST2
SMSEMI
54
53
52
51
50
TST0
57
49
MCKO
58
CAD0
59
DVDD
60
TST1
61
1 IBICK2
XTO 48
2 IMCLK
XTI/OMCLK 47
FSO
FSI
DSP1
62
VSS1
ILRCK2
DSP2
63
VSS5
C1
+
64
64FSI
3 ILRCK1
OLRCK 46
4 IBICK1
OBICK 45
5 DVDD
DVDD 44
64FSO
C1
C1
6 VSS2
VSS4 43
DSP5
7 SDTI4
SDTO4 42
8 SDTI1
SDTO1 41
Top View
9 SDTI2
SDTO2 40
10 SDTI3
SDTO3 39
11 IDIF0
ODIF0 38
12 IDIF1
ODIF1 37
13 IDIF2
CM0 36
14 ILRCK3
CM1 35
15 IBICK3
CM2 34
16 ILRCK4
TDM 33
DSP3
IBICK4
INAS
UNLOCK
DVDD
VSS3
SMUTE
DITHER
PDN
SMT0
SMT1
DEM0
DEM1
PM1
OBIT0
OBIT1
PM2
DSP4
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
C1
+
C2
uP
Notes:
- All digital input pins should be not left floating.
- VSS1 -5 must be connected to the same ground plane.
- Connect a 1μF (± 30%; including temperature characteristics) capacitor between the VD18 pin and DVSS. When
this capacitor is polarized, the positive polarity pin should be connected to the VD18 pin.
- Refer to Table 5 for the equivalent series resistance R1 and capacitance C values of the X’tal oscillator.
Figure 49. Typical Connection Diagram (Serial Control Mode)
MS1173-E-02
2011/06
- 45 -
[AK4129]
1. Grounding and Power Supply Decoupling
The AK4129 requires careful attention to power supply and grounding arrangements. Alternatively if AVDD and
DVDD1-4 are supplied separately, the power up sequence is not critical. VSS1-5 must be connected to the same
ground plane. Decoupling capacitors should be as near to the AK4129 as possible, with the small value ceramic
capacitor being the nearest.
2. Jitter Tolerance
Figure 50 shows the jitter tolerance to ILRCK3-1 and IBICK. The jitter quantity is defined by the jitter frequency and the
jitter amplitude shown in Figure 50. When the jitter amplitude is 0.02Uipp or less, the AK4129 operates normally
regardless of the jitter frequency.
Figure 50. Jitter Tolerance
(1) Normal Operation
(2) There is a possibility that the output data is lost.
Note
▪ Y axis is the jitter amplitude of ILRCK3-1 just before THD+N degradation starts.
1UI (Unit Interval) is one cycle of IBICK. When FSI = 48kHz, 1[UIpp]=1/48kHz=20.8μs
MS1173-E-02
2011/06
- 46 -
[AK4129]
3. Digital Filter Response Example
Table 14 shows the examples of digital filter response performed by the AK4129.
Ratio
FSO/FSI [kHz]
4.000
1.000
0.919
0.725
0.667
0.544
0.500
0.500
0.459
0.363
0.333
0.250
0.250
0.230
0.167
0.181
0.167
0.181
192/48.0
48.0/48.0
44.1/48.0
32.0/44.1
32.0/48.0
48.0/88.2
48.0/96.0
44.1/88.2
44.1/96.0
32.0/88.2
32.0/96.0
48.0/192.0
44.1/176.4
44.1/192.0
32.0/192.0
32.0/176.4
8/48.0
8/44.1
Stopband
Attenuation [dB]
22.000
26.000
−121.2
22.000
26.000
−121.2
20.000
24.100
−121.4
14.088
17.487
−115.3
13.688
17.488
−116.9
19.250
26.232
−114.6
20.900
27.000
−100.2
19.202
24.806
−100.2
18.700
25.000
−103.3
12.863
18.665
−102.0
12.500
18.900
−103.6
17.600
30.200
−104.0
16.170
27.746
−104.0
15.860
28.240
−103.3
11.200
19.600
−73.2
10.278
17.987
−73.2
2.800
4.900
−73.2
2.5695
4.4968
−73.2
Table 14. Digital Filter Example
Passband [kHz]
Stopband [kHz]
Gain [dB]
−0.01@ 20k
−0.01@ 20k
−0.01@ 20k
−0.01@ 14.5k
−0.19@ 14.5k
−0.03@ 20k
−0.01@ 20k
−0.08@ 20k
−0.23@ 20k
−0.75@ 14.5k
−1.07@ 14.5k
−0.18@ 20k
−1.34@ 20k
−1.40@ 20k
−2.97@ 14.5k
−7.88@ 14.5k
−2.97@ 3.625k
−7.88@ 3.625k
4. I2C bus Connection
SCL and SDA pins should be connected to DVDD1-4 through the resistor based on I2C standard. As there is a protection
between each pin and DVDD1-4, the pulled up voltage must be DVDD1-4 or lower (Figure 51).
+3.3V
DVDD1-4
AK4129
SDA pin
VSS2-5
Figure 51. SDA pin output
MS1173-E-02
2011/06
- 47 -
[AK4129]
PACKAGE
64pin LQFP(Unit: mm)
12.0
Max 1.85
10.0
1.40
0.00~0.25
33
32
48
12.0
49
64
17
16
1
0.5
0.2±0.1
0.09~0.25
0.10 M
0°~10°
0.50±0.25
0.10
■ Material & Lead finish
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy
Cu
Solder (Pb free) plate
MS1173-E-02
2011/06
- 48 -
[AK4129]
MARKING (AK4129EQ)
AKM
AK4129EQ
XXXXXXX
1
XXXXXXX: Date code identifier
MARKING (AK4129VQ)
AKM
AK4129VQ
XXXXXXX
1
XXXXXXX: Date code identifier
MS1173-E-02
2011/06
- 49 -
[AK4129]
REVISION HISTORY
Date (YY/MM/DD)
10/05/14
10/09/14
Revision
00
01
Reason
First Edition
Error Correction
Page
6
11/06/02
02
Specification
Change
Error Correction
Specification
Change
Description
Addition
36
45
48
4
Contents
The registration number was corrected.
MS1174-E-xx → MS1173-E-xx
PIN/FUNCTION
Pin No. 22: (Note 5) → (Note 3)
■ Internal Reset Function for Clock Change
“min. 58.05 MHz” → “min. 59.4MHz”
Figure 49 was changed.
PACKAGE
The package dimensions were changed.
■ Compatibility with AK4126
(2) Pins: No. 63-pin was added.
IMPORTANT NOTICE
z These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
z Descriptions of external circuits, application circuits, software and other related information contained in this
document are provided only to illustrate the operation and application examples of the semiconductor products. You
are fully responsible for the incorporation of these external circuits, application circuits, software and other related
information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third
parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent,
intellectual property, or other rights in the application or use of such information contained herein.
z Any export of these products, or devices or systems containing them, may require an export license or other official
approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange,
or strategic materials.
z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or
other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and
which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or
perform may reasonably be expected to result in loss of life or in significant injury or damage to person or
property.
z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places
the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer
or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all
claims arising from the use of said product in the absence of such notification.
MS1173-E-02
2011/06
- 50 -