INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: • The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications • The IC06 74HC/HCT/HCU/HCMOS Logic Package Information • The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines 74HC/HCT123 Dual retriggerable monostable multivibrator with reset Product specification Supersedes data of September 1993 File under Integrated Circuits, IC06 1998 Jul 08 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 • Retriggerable for very long pulses up to 100% duty factor and early reset. The basic output pulse width is essentially determined by the values of the external timing components REXT and CEXT. For pulse widths, when CEXT < 10 000 pF, see Fig.9. • Direct reset terminates output pulse When CEXT > 10 000 pF, the typical output pulse width is defined as: FEATURES • DC triggered from active HIGH or active LOW inputs • Schmitt-trigger action on all inputs except for the reset input where: tW = pulse width in ns; REXT = external resistor in kΩ; CEXT = external capacitor in pF. Schmitt-trigger action in the nA and nB inputs, makes the circuit highly tolerant to slower input rise and fall times. tW = 0.45 × REXT × CEXT (typ.), The ‘123’ is identical to the ‘423’ but can be triggered via the reset input. • Output capability: standard (except for nREXT/CEXT) • ICC category: MSI GENERAL DESCRIPTION The 74HC/HCT123 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT123 are dual retriggerable monostable multivibrators with output pulse width control by three methods. The basic pulse time is programmed by selection of an external resistor (REXT) and capacitor (CEXT). The external resistor and capacitor are normally connected as shown in Fig.6. Once triggered, the basic output pulse width may be extended by retriggering the gated active LOW-going edge input (nA) or the active HIGH-going edge input (nB). By repeating this process, the output pulse period (nQ = HIGH, nQ = LOW) can be made as long as desired. Alternatively an output delay can be terminated at any time by a LOW-going edge on input nRD, which also inhibits the triggering. QUICK REFERENCE DATA GND = 0 V; Tamb = 25 °C; tr = tf = 6 ns TYPICAL SYMBOL PARAMETER UNIT HC tPHL/ tPLH propagation delay nA, nB to nQ, nQ nRD to nQ, nQ CI input capacitance CPD power dissipation capacitance per monostable CL = 15 pF; VCC = 5 V; REXT = 5 kΩ; CEXT = 0 pF notes 1 and 2 HCT 26 26 ns 20 23 ns 3.5 3.5 pF 54 56 pF Notes 1. CPD is used to determine the dynamic power dissipation (PD in µW): PD = CPD × VCC2 × fi + ∑(CL × VCC2 × fo) + 0.75 × CEXT × VCC2 × fo + D × 16 × VCC where: fi = input frequency in MHz fo = output frequency in MHz D = duty factor in % CL = output load capacitance in pF VCC = supply voltage in V CEXT = timing capacitance in pF ∑ (CL × VCC2 × fo) sum of outputs 2. For HC the condition is VI = GND to VCC For HCT the condition is VI = GND to VCC − 1.5 V An internal connection from nRD to the input gates makes it possible to trigger the circuit by a positive-going signal at input nRD as shown in the function table. Figures 7 and 8 illustrate pulse control by retriggering 1998 Jul 08 CONDITIONS 2 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 ORDERING INFORMATION PACKAGE TYPE NUMBER NAME DESCRIPTION VERSION 74HC123N; 74HCT123N DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 74HC123D; 74HCT123D SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 74HC123DB; 74HCT123DB SSOP16 74HC123PW; 74HCT123PW TSSOP16 PIN DESCRIPTION PIN NO. SYMBOL NAME AND FUNCTION 1, 9 1A, 2A trigger inputs (negative-edge triggered) 2, 10 1B, 2B trigger inputs (positive-edge triggered) 3, 11 1RD, 2RD direct reset LOW and trigger action at positive edge 4, 12 1Q, 2Q outputs (active LOW) 7 2REXT/CEXT external resistor/capacitor connection 8 GND ground (0 V) 13, 5 1Q, 2Q outputs (active HIGH) 14, 6 1CEXT, 2CEXT external capacitor connection 15 1REXT/CEXT external resistor/capacitor connection 16 VCC positive supply voltage Fig.1 Pin configuration. 1998 Jul 08 Fig.2 Logic symbol. 3 Fig.3 IEC logic symbol. Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 FUNCTION TABLE INPUTS nRD L nA X OUTPUTS nB nQ nQ X L H H(1) H(1) X H X L(1) X X L L(1) H L ↑ H ↓ H ↑ L H 1. If the monostable was triggered before this condition was established, the pulse will continue as programmed. (1) For minimum noise generation, it is recommended to ground pins 6 (2CEXT) and 14 (1CEXT) externally to pin 8 (GND). Fig.5 Logic diagram. 1998 Jul 08 = HIGH voltage level L = LOW voltage level X = don’t care ↑ = LOW-to-HIGH transition ↓ = HIGH-to-LOW transition = one HIGH level output pulse = one LOW level output pulse Note Fig.4 Functional diagram. H 4 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 Fig.6 Timing component connections. DC CHARACTERISTICS FOR 74HC For the DC characteristics see “74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: standard (except for nREXT/CEXT) ICC category: MSI 1998 Jul 08 5 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 AC CHARACTERISTICS FOR 74HC GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (°C) TEST CONDITIONS 74HC SYMBOL PARAMETER −40 to +85 −40 to +125 min. typ. max. min. max. min. max. +25 UNIT V CC (V) WAVEFORMS/ NOTES tPLH propagation delay nRD, nA, nB to nQ 83 30 24 255 51 43 320 64 54 385 77 65 ns 2.0 4.5 6.0 CEXT = 0 pF; REXT = 5 kΩ tPLH propagation delay nRD, nA, nB to nQ 83 30 24 255 51 43 320 64 54 385 77 65 ns 2.0 4.5 6.0 CEXT = 0 pF; REXT = 5 kΩ tPHL propagation delay nRD to nQ (reset) 66 24 19 215 43 37 270 54 46 325 65 55 ns 2.0 4.5 6.0 CEXT = 0 pF; REXT = 5 kΩ tPLH propagation delay nRD to nQ (reset) 66 24 19 215 43 37 270 54 46 325 65 55 ns 2.0 4.5 6.0 CEXT = 0 pF; REXT = 5 kΩ tTHL / tTLH output transition time 19 7 6 75 15 13 95 19 16 110 22 19 ns 2.0 4.5 6.0 tW trigger pulse width nA = LOW 100 20 17 8 3 2 125 25 21 150 30 26 ns 2.0 4.5 6.0 Fig.7 tW trigger pulse width nB = HIGH 100 20 17 17 6 5 125 25 21 150 30 26 ns 2.0 4.5 6.0 Fig.7 tW reset pulse width nRD = LOW 100 20 17 14 5 4 125 25 21 150 30 26 ns 2.0 4.5 6.0 Fig.8 tW output pulse width nQ = HIGH nQ = LOW 450 − − µs 5.0 CEXT = 100 nF; REXT = 10 kΩ; Figs 7 and 8 tW output pulse width nQ = HIGH nQ = LOW 75 − − ns 5.0 CEXT = 0 pF; REXT = 5 kΩ; note 1; Figs 7 and 8 trt retrigger time nA, nB 110 − − ns 5.0 CEXT = 0 pF; REXT = 5 kΩ; note 2; Fig.7 REXT external timing resistor 1000 − 1000 − kΩ 2.0 5.0 Fig.9 CEXT external timing capacitor pF 5.0 Fig.9; note 3 1998 Jul 08 10 2 no limits 6 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 DC CHARACTERISTICS FOR 74HCT For the DC characteristics see “74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: standard (except for nREXT / CEXT) ICC category: MSI Note to HCT types The value of additional quiescent supply current (∆ICC) for a unit load of 1 is given in the family specifications. To determine ∆ICC per input, multiply this value by the unit load coefficient shown in the table below. INPUT UNIT LOAD COEFFICIENT nA, nB 0.35 nRD 0.50 1998 Jul 08 7 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 AC CHARACTERISTICS FOR 74HCT GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (°C) TEST CONDITIONS 74HCT SYMBOL PARAMETER −40 to +85 +25 −40 to +125 min. typ. max. min. max. min. UNIT V CC (V) WAVEFORMS/ NOTES max. tPHL propagation delay nRD, nA, nB to nQ 30 51 64 77 ns 4.5 CEXT = 0 pF; REXT = 5 kΩ tPLH propagation delay nRD, nA, nB to nQ 28 51 64 77 ns 4.5 CEXT = 0 pF; REXT = 5 kΩ tPHL propagation delay nRD to nQ (reset) 27 46 58 69 ns 4.5 CEXT = 0 pF; REXT = 5 kΩ tPLH propagation delay nRD to nQ (reset) 23 46 58 69 ns 4.5 CEXT = 0 pF; REXT = 5 kΩ tTHL / tTLH output transition time 7 15 19 22 ns 4.5 tW trigger pulse width nA = LOW 20 3 25 30 ns 4.5 Fig.7 tW trigger pulse width nB = HIGH 20 5 25 30 ns 4.5 Fig.7 tW reset pulse width nRD = LOW 20 7 25 30 ns 4.5 Fig.8 tW output pulse width nQ = HIGH nQ = LOW 450 − − µs 5.0 CEXT = 100 nF; REXT = 10 kΩ; Figs 7 and 8 tW output pulse width nQ = HIGH nQ = LOW 75 − − ns 5.0 CEXT = 0 pF; REXT = 5 kΩ; note 1; Figs 7 and 8 trt retrigger time nA, nB 110 − − ns 5.0 CEXT = 0 pF; REXT = 5 kΩ; note 2; Fig.7 REXT external timing resistor 1000 − − kΩ 5.0 Fig.9 CEXT external timing capacitor pF 5.0 Fig.9; note 3 1998 Jul 08 2 no limits 8 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 Notes to AC characteristics 1. For other REXT and CEXT combinations see Fig.9. If CEXT > 10 nF, the next formula is valid: tW = K × REXT × CEXT (typ.) where: tW = output pulse width in ns; REXT = external resistor in kΩ; CEXT = external capacitor in pF; K = constant = 0.55 for VCC = 5.0 V and 0.48 for VCC = 2.0 V. The inherent test jig and pin capacitance at pins 15 and 7 (nREXT / CEXT) is approximately 7 pF. 2. The time to retrigger the monostable multivibrator depends on the values of REXT and CEXT. The output pulse width will only be extended when the time between the active-going edges of the trigger input pulses meets the minimum retrigger time. If CEXT > 10 pF, the next formula (at VCC = 5.0 V) for the set-up time of a retrigger pulse is valid: trt = 30 + 0.19 × REXT × CEXT0.9 + 13 × REXT1.05 (typ.) where: trt = retrigger time in ns; CEXT = external capacitor in pF; REXT = external resistor in kΩ. The inherent test jig and pin capacitance at pins 15 and 7 (nREXT / CEXT) is 7 pF. 3. When the device is powered-up, initiate the device via a reset pulse, when CEXT < 50 pF. 1998 Jul 08 9 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 AC WAVEFORMS Fig.7 Fig.9 Fig.8 Output pulse control using retrigger pulse; nRD = HIGH. Typical output pulse width as a function of the external capacitor values at VCC = 5.0 V and Tamb = 25 °C. 1998 Jul 08 Output pulse control using reset input in nRD; nA = LOW. Fig.10 HCT typical “k” factor as a function of VCC; CX = 10 nF; RX = 10 kΩ to 100 kΩ. 10 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 APPLICATION INFORMATION Power-up considerations When the monostable is powered-up it may produce an output pulse, with a pulse width defined by the values of RX and CX, this output pulse can be eliminated using the circuit shown in Fig.11. Fig.11 Power-up output pulse elimination circuit. Power-down considerations A large capacitor (CX) may cause problems when powering-down the monostable due to the energy stored in this capacitor. When a system containing this device is powered-down or a rapid decrease of VCC to zero occurs, the monostable may substain damage, due to the capacitor discharging through the input protection diodes. To avoid this possibility, use a damping diode (DX) preferably a germanium or Schottky type diode able to withstand large current surges and connect as shown in Fig.12 Fig.12 Power-down protection circuit. 1998 Jul 08 11 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 PACKAGE OUTLINES DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 9 16 pin 1 index E 1 8 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.7 0.51 3.7 1.40 1.14 0.53 0.38 0.32 0.23 21.8 21.4 6.48 6.20 2.54 7.62 3.9 3.4 8.25 7.80 9.5 8.3 0.254 2.2 inches 0.19 0.020 0.15 0.055 0.045 0.021 0.015 0.013 0.009 0.86 0.84 0.26 0.24 0.10 0.30 0.15 0.13 0.32 0.31 0.37 0.33 0.01 0.087 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT38-1 050G09 MO-001AE 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 92-10-02 95-01-19 12 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE v M A Z 16 9 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 8 e 0 detail X w M bp 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.39 0.014 0.0075 0.38 0.16 0.15 0.050 0.039 0.016 0.028 0.020 0.01 0.01 0.004 0.028 0.012 inches 0.244 0.041 0.228 θ Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT109-1 076E07S MS-012AC 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 95-01-23 97-05-22 13 o 8 0o Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm D SOT338-1 E A X c y HE v M A Z 9 16 Q A2 A (A 3) A1 pin 1 index θ Lp L 8 1 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) θ mm 2.0 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 7.9 7.6 1.25 1.03 0.63 0.9 0.7 0.2 0.13 0.1 1.00 0.55 8 0o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 1998 Jul 08 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 94-01-14 95-02-04 MO-150AC 14 o Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index θ Lp L 1 8 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ mm 1.10 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1.0 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8 0o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 1998 Jul 08 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 94-07-12 95-04-04 MO-153 15 o Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Typical reflow temperatures range from 215 to 250 °C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C. WAVE SOLDERING This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (order code 9398 652 90011). Wave soldering can be used for all SO packages. Wave soldering is not recommended for SSOP and TSSOP packages, because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices. DIP If wave soldering is used - and cannot be avoided for SSOP and TSSOP packages - the following conditions must be observed: SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. • A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. • The longitudinal axis of the package footprint must be parallel to the solder flow and must incorporate solder thieves at the downstream end. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Even with these conditions: • Only consider wave soldering SSOP packages that have a body width of 4.4 mm, that is SSOP16 (SOT369-1) or SSOP20 (SOT266-1). • Do not consider wave soldering TSSOP packages with 48 leads or more, that is TSSOP48 (SOT362-1) and TSSOP56 (SOT364-1). REPAIRING SOLDERED JOINTS Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. SO, SSOP and TSSOP Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C. REFLOW SOLDERING Reflow soldering techniques are suitable for all SO, SSOP and TSSOP packages. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. 1998 Jul 08 16 Philips Semiconductors Product specification Dual retriggerable monostable multivibrator with reset 74HC/HCT123 REPAIRING SOLDERED JOINTS Fix the component by first soldering two diagonally- opposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1998 Jul 08 17