MASW-011055 Switch, SP2T 100 Watt Reflective 0.03 - 3.0 GHz Features Rev. V1 Functional Schematic Suitable for High Power Military and Civilian Radio Applications Power Handling: 100 W @ 85°C Insertion Loss: 0.35 dB @ 2 GHz Isolation: 51 dB @ 2 GHz Lead-Free 5 mm HQFN-12LD Package RoHS* Compliant and 260°C Reflow Compatible N/C RFC N/C 12 11 10 N/C 1 9 N/C Description N/C 2 8 N/C The MASW-011055 is a high power PIN diode SP2T switch in a common anode configuration, operating from 30 MHz to 3 GHz. It features low insertion loss and excellent linearity. This device is capable of handling 100 Watts CW incident power at a base plate temperature of 85ºC. RF1 3 7 RF2 This high power switch is ideal for use on land mobile radio and MIL-COM applications that require higher CW and pulsed power operation. The MASW-011055 is manufactured using MACOM’s hybrid manufacturing process featuring high voltage PIN diodes and passive devices integrated in a 5 mm HQFN 12-lead plastic package. Ordering Information1 Part Number Package MASW-011055-TR0500 500 piece reel MASW-011055-SMB Sample Board 4 5 6 B1 N/C B2 Pin Configuration Pin Function Pin Function 1 No Connection 7 RF2 / V2 Bias 2 No Connection 8 No Connection 3 RF1 / V1 Bias 9 No Connection 4 B1 Bias 10 No Connection 5 No Connection 11 RFC / V3 Bias 6 B2 Bias 12 No Connection Paddle2 Ground 2. The exposed pad centered on the package bottom must be connected to RF, DC and thermal ground. 1. Reference Application Note M513 for reel size information. * Restrictions on Hazardous Substances, European Union Directive 2011/65/EU. 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASW-011055 Switch, SP2T 100 Watt Reflective 0.03 - 3.0 GHz Rev. V1 Electrical Specifications: TA = 25°C, Bias3 = +5 / -5 V, 50 mA / 100 mA Parameter Test Conditions Units Min. Typ. Max. Insertion Loss PIN = 0 dBm 0.5 GHz 1 GHz 2 GHz dB — 0.10 0.20 0.35 — 0.50 — Isolation PIN = 0 dBm 0.5 GHz 1 GHz 2 GHz dB — 48 — 52 54 51 — Input Return Loss PIN = 0 dBm dB — >15 — CW Input Power 25°C base plate, 2 GHz dBm W — 52 158 — CW Input Power 85°C base plate, 2 GHz dBm W — 50 100 — P0.1dB 25°C base plate, 2 GHz dBm — >52 — Input IP3 F1 = 2000 MHz, F2 = 2010 MHz PIN = 40 dBm/Tone, 28 V dBm — 66 — RF Switching Speed (10-90% RF Voltage) 1 MHz Rep Rate in Modulating Mode ns — 500 — 3. See Bias table. Bias (+5 V / -5 V) V1 Bias (V) V2 Bias (V) V3 Bias (V) B1 Bias (V) B2 Bias (V) RFC – RF1 Low Loss RFC – RF2 Isolation -5 V @ 100 mA +5 V @ 50 mA 0V 0V 0V RFC – RF2 Low Loss RFC – RF1 Isolation +5 V @ 50 mA -5 V @ 100 mA 0V 0V 0V RF State 4. DC reverse bias of a PIN Diode operating at a high power is dependent on RF frequency, incident power, and VSWR. See Minimum Reverse DC Voltage table for high power operation. 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASW-011055 Switch, SP2T 100 Watt Reflective 0.03 - 3.0 GHz Minimum Reverse DC Voltage5 Frequency (MHz) Minimum Reverse DC Voltage 30 | -120 V | 100 | -119 V | 200 | -114 V | 300 | -106 V | 500 | -90 V | Rev. V1 Application Schematic RFC C8 C7 L5 V3 R3 V1 1000 | -59 V | 1500 | -43 V | 2000 | -33 V | V2 C6 C1 L1 RF1 L4 C2 C5 L2 R1 L3 R2 B1 B2 C3 C4 5. Required to maintain low loss under 100 W of incident power with 1.5:1 VSWR. Absolute Maximum Ratings6,7 Parameter Absolute Maximum Off-Chip Component Values Operating Frequency Component Size 0.03 - 1.0 GHz 0.5 - 3.0 GHz Forward Current 200 mA Reverse DC Voltage -150 V Operating Temperature -40°C to +85°C Storage Temperature -55°C to +150°C Junction Temperature +175°C 6. Exceeding any one or combination of these limits may cause permanent damage to this device. 7. MACOM does not recommend sustained operation near these survivability limits. C1, C3, C4, C6, C7, C8 0.1 µF 270 pF 0603 C2, C5, C8 0.1 µF 27 pF 0603 L1 - L5 3.3 µH 82 nH 0603 R1 - R28 82 Ω 82 Ω 1210 R38 39 Ω 39 Ω 1210 8. Resistance values are used for small signal testing under +5 V / -5 V bias conditions. 3 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support RF3 MASW-011055 Switch, SP2T 100 Watt Reflective 0.03 - 3.0 GHz Rev. V1 Typical Performance Curves @ +25°C (using external bias tees): Insertion Loss Isolation 0.0 0 -10 -0.2 RFC - RF1 RFC - RF2 -20 (dB) (dB) -0.4 -0.6 -1.0 -40 -50 RFC - RF1 RFC - RF2 -0.8 -30 -60 0.0 0.5 1.0 1.5 2.0 2.5 -70 0.0 3.0 0.5 1.0 Frequency (GHz) 1.5 2.0 2.5 3.0 2.5 3.0 Frequency (GHz) Input Return Loss Output Return Loss 0 0 RFC - RF1 RFC - RF2 -10 RFC - RF1 RFC - RF2 -10 (dB) -20 (dB) -20 -30 -30 -40 -40 -50 0.0 0.5 1.0 1.5 2.0 Frequency (GHz) 2.5 3.0 -50 0.0 0.5 1.0 1.5 2.0 Frequency (GHz) 4 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASW-011055 Switch, SP2T 100 Watt Reflective 0.03 - 3.0 GHz Rev. V1 Lead Free 5 mm 12-Lead HQFN † † Reference Application Note S2083 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 1 requirements. Plating is NiPdAuAg. Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Silicon Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these Class 1B HBM devices. 5 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support