AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com AM335x ARM® Cortex™-A8 Microprocessors (MPUs) Check for Samples: AM3359, AM3358 1 Device Summary 1.1 Features • Highlights – 275-MHz, 500-MHz, 600-MHz, or 720-MHz ARM® Cortex™-A8 32-Bit RISC Microprocessor • NEON™ SIMD Coprocessor • 32KB/32KB of L1 Instruction/Data Cache with Single-Error Detection (parity) • 256KB of L2 Cache with Error Correcting Code (ECC) – mDDR(LPDDR)/DDR2/DDR3 Support – General-Purpose Memory Support (NAND, NOR, SRAM, etc.) Supporting Up to 16-bit ECC – SGX530 Graphics Engine – LCD Controller With WXGA Resolution at 60-Hz Refresh Rate – Programmable Real-Time Unit Subsystem – Real-Time Clock (RTC) – Up to Two USB 2.0 High-Speed OTG Ports with Integrated PHY – 10/100/1000 Ethernet Switch Supporting Up to Two Ports – Serial Interfaces Including: • Two Controller Area Network Ports (CAN) • Six UARTs, Two McASPs, Two McSPI, and Three I2C Ports – 12-Bit Successive Approximation Register (SAR) ADC – Up to Three 32-Bit Enhanced Capture Modules (eCAP) – Up to Three Enhanced High-Resolution PWM Modules (eHRPWM) – Crypto Hardware Accelerators (AES, SHA, PKA, RNG) • MPU Subsystem – 275-MHz, 500-MHz, 600-MHz, or 720-MHz ARM® Cortex™-A8 32-Bit RISC Microprocessor – NEON™ SIMD Coprocessor – 32KB of L1 Instruction Cache with Single-Error Detection (parity) – 32KB of L1 Data Cache with Single Error-Detection (parity) – 256KB of L2 Cache with Error Correcting Code (ECC) – 176KB of On-Chip Boot ROM – 64KB of Dedicated RAM – Emulation/Debug • JTAG • Embedded Trace Buffer – Interrupt Controller (up to 128 interrupt requests) • On-Chip Memory (Shared L3 RAM) – 64 KB of General-Purpose On-Chip Memory Controller (OCMC) RAM – Accessible to all Masters – Supports Retention for Fast Wake-Up • External Memory Interfaces (EMIF) – mDDR/DDR2/DDR3 Controller: • mDDR: 200-MHz Clock (400-MHz Data Rate) • DDR2: 266-MHz Clock (532-MHz Data Rate) • DDR3: 303-MHz Clock (606-MHz Data Rate) • 16-Bit Data Bus • 1 GB of Total Addressable Space • Supports One x16 or Two x8 Memory Device Configurations • Supports Retention for Fast Wake-Up – General-Purpose Memory Controller (GPMC) • Flexible 8/16-Bit Asynchronous Memory Interface with Up to seven Chip Selects (NAND, NOR, Muxed-NOR, SRAM, etc.) • Uses BCH Code to Support 4-Bit, 8-Bit, or 16-Bit ECC • Uses Hamming Code to Support 1-Bit ECC 1 2 3 4 5 6 7 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SmartReflex, DSP/BIOS, XDS are trademarks of Texas Instruments. Cortex, NEON are trademarks of ARM Ltd or its subsidiaries. ARM is a registered trademark of ARM Ltd or its subsidiaries. EtherCAT is a registered trademark of EtherCAT Technology Group. POWERVR SGX is a trademark of Imagination Technologies Limited. All other trademarks are the property of their respective owners. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. Copyright © 2011–2012, Texas Instruments Incorporated PRODUCT PREVIEW 1234567 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 PRODUCT PREVIEW – Error Locator Module (ELM) • Used in Conjunction with the GPMC to Locate Addresses of Data Errors from Syndrome Polynomials Generated Using a BCH Algorithm • Supports 4-Bit, 8-Bit, and 16-Bit per 512-byte Block Error Location Based on BCH Algorithms • Programmable Real-Time Unit Subsystem (PRUSS) – Two Programmable Real-Time Units (PRUs) • 32-Bit Load/Store RISC Processor Capable of Running at 200 MHz • 8 KB Instruction RAM with Single-Error Detection (parity) • 8 KB Data RAM with Single-Error Detection (parity) • Single-Cycle 32-Bit Multiplier with 64-Bit Accumulator • Enhanced GPIO Module Provides Shift-In/Out Support and Parallel Latch on External Signal – 12 KB of Shared RAM with Single-Error Detection (parity) – Three 120-byte Register Banks Accessible by Each PRU – Interrupt Controller Module (INTC) for Handling System Input Events – Local Interconnect Bus for Connecting Internal and External Masters to the Resources Inside the PRUSS – Peripherals Inside the PRUSS • One UART Port with Flow Control Pins, Supports Up to 12 Mbps • Two MII Ethernet Ports that Support Industrial Ethernet, such as EtherCAT® • One MDIO Port • One Enhanced Capture (eCAP) Module • Power Reset and Clock Management (PRCM) Module – Controls the entry and Exit of Stand-By and Deep-Sleep Modes – Responsible for Sleep Sequencing, Power Domain Switch-Off Sequencing, Wake-Up Sequencing and Power Domain Switch-On Sequencing – Clocks • Integrated 15-35 MHz High-Frequency Oscillator Used to Generate a Reference Clock for Various System and Peripheral Clocks • Supports Individual Clock Enable/Disable Control for Subsystems and Peripherals to Facilitate Reduced Power Consumption 2 Device Summary www.ti.com • Five ADPLLs to Generate System Clocks (MPU Subsystem, DDR Interface, USB and Peripherals [MMC/SD, UART, SPI, I2C, etc.], L3, L4, Ethernet, GFX [SGX530], LCD Pixel Clock) – Power • Two Non-Switchable Power Domains (Real-Time Clock [RTC], Wake-Up Logic [WAKE-UP]) • Three Switchable Power Domains (MPU Subsystem [MPU], SGX530 [GFX], Peripherals and Infrastructure [PER]) • Implements SmartReflex™ Class 2B for Core Voltage Scaling Based On Die Temperature, Process Variation and Performance (Adaptive Voltage Scaling [AVS]) • Dynamic Voltage Frequency Scaling (DVFS) • Real-Time Clock (RTC) – Real-Time Date (Day/Month/Year/Day of Week) and Time (Hours/Minutes/Seconds) Information – Internal 32.768-kHz Oscillator, RTC Logic and 1.1-V Internal LDO – Independent Power-on-Reset (RTC_PWRONRSTn) Input – Dedicated Input Pin (EXT_WAKEUP) for External Wake Events – Programmable Alarm Can be Used to Generate Internal Interrupts to the PRCM (for Wake Up) or Cortex-A8 (for Event Notification) – Programmable alarm Can be Used with External Output (PMIC_POWER_EN) to Enable the Power Management IC to Restore Non-RTC Power Domains • Peripherals – Up to Two USB 2.0 High-Speed OTG Ports with Integrated PHY – Up to Two Industrial Gigabit Ethernet MACs (10/100/1000 Mbps) • Integrated Switch • Each MAC Supports MII/RMII/RGMII and MDIO Interfaces • Ethernet MACs and Switch Can Operate Independent of Other Functions • IEEE 1588 Precision Time Protocol (PTP) – Up to Two Controller-Area Network (CAN) Ports • Supports CAN Version 2 Parts A and B – Up to Two Multichannel Audio Serial Ports (McASP) • Transmit/Receive Clocks Up to 50 MHz • Up to Four Serial Data Pins per McASP Port with Independent TX/RX Clocks Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com • – – – – – – – – Balancing and Power Management Advanced Geometry DMA Driven Operation for Minimum CPU Interaction • Programmable High-Quality Image Anti-Aliasing • Fully Virtualized Memory Addressing for OS Operation in a Unified Memory Architecture LCD Controller • Up to 24-Bits Data Output; 8-Bits per Pixel (RGB) • Up to WXGA (1366x768) Resolution • Integrated LCD Interface Display Driver (LIDD) Controller • Integrated Raster Controller • Integrated DMA Engine to Pull Data from the External Frame Buffer without Burdening the Processor via Interrupts or a Firmware Timer • 512-Word Deep Internal FIFO • Supported Display Types: – Character Displays - Uses LCD Interface Display Driver (LIDD) Controller to Program these Displays – Passive Matrix LCD Displays - Uses LCD Raster Display Controller to Provide Timing and Data for Constant Graphics Refresh to a Passive Display – Active Matrix LCD Displays - Uses External Frame Buffer Space and the Internal DMA Engine to Drive Streaming Data to the Panel. Maximum Resolution is WXGA (1366x768) at 60-Hz Refresh Rate 12-Bit Successive Approximation Register (SAR) ADC • 100K Samples per Second • Input Can be Selected from any of the Eight Analog Inputs Multiplexed Through an 8:1 analog Switch • Can be Configured to Operate as a 4-wire, 5-wire, or 8-wire Resistive Touch Screen Controller (TSC) Interface Up to Three 32-Bit Enhanced Capture Modules (eCAP) • Configurable as Three Capture Inputs or Three Auxiliary PWM Outputs Up to Three Enhanced High-Resolution PWM Modules (eHRPWM) • Dedicated 16-Bit Time-Base Counter with Time and Frequency Controls • Configurable as Six Single-Ended, Six Dual-Edge Symmetric, or Three Dual-Edge Asymmetric Outputs Up to Three 32-Bit Enhanced Quadrature Pulse Encoder (eQPE) Modules • – – – – – Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Device Summary 3 PRODUCT PREVIEW – Supports Time Division Multiplexing (TDM), Inter-IC Sound (I2S), and similar Formats • Supports Digital Audio Interface Transmission (SPDIF, IEC60958-1, and AES-3 Formats) • FIFO Buffers for Transmit and Receive (256 bytes) Up to Six UARTs • All UARTs Support IrDA and CIR Modes • All UARTs Support RTS and CTS Flow Control • UART1 Supports Full Modem control Up to Two Master/Slave McSPI Serial Interfaces • Up to Two Chip Selects • Up to 48 MHz Up to Three MMC/SD/SDIO Ports • 1-Bit, 4-Bit and 8-Bit MMC/SD/SDIO Modes • MMCSD0 has dedicated Power Rail for 1.8-V or 3.3-V Operation • Up to 48-MHz Data Transfer Rate • Supports Card Detect and Write Protect • Complies with MMC4.3 and SD/SDIO 2.0 Specifications Up to Three I2C Master/Slave Interfaces • Standard Mode (up to 100 kHz) • Fast Mode (up to 400 kHz) Up to Four Banks of General-Purpose IO (GPIO) • 32 GPIOs per Bank (Multiplexed with Other Functional Pins) • GPIOs Can be Used as Interrupt Inputs (Up to Two Interrupt Inputs per Bank) Up to Three External DMA Event Inputs That Can Also be Used as Interrupt Inputs Eight 32-Bit General-Purpose Timers • DMTIMER1 is a 1-ms Timer Used for Operating System (OS) Ticks • DMTIMER4 - DMTIMER7 are Pinned Out One Watchdog Timer SGX530 3D Graphics Engine • Tile-Based Architecture Delivering Up to 20 MPloy/sec • Universal Scalable Shader Engine is a Multi-Threaded Engine Incorporating Pixel and Vertex Shader Functionality • Advanced Shader Feature Set in Excess of Microsoft VS3.0, PS3.0 and OGL2.0 • Industry Standard API Support of Direct3D Mobile, OGL-ES 1.1 and 2.0, OpenVG 1.0, and OpenMax • Fine-Grained Task Switching, Load AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 PRODUCT PREVIEW • Device Identification – Contains Electrical fuse Farm (FuseFarm) of Which Some Bits are Factory Programmable • Production ID • Device Part Number (Unique JTAG ID) • Device Revision (readable by Host ARM) • Debug Interface Support – JTAG/cJTAG for ARM (Cortex-A8 and PRCM), PRU Debug – Embedded Trace Buffer (ETB) – Supports Device Boundary Scan – Supports IEEE1500 • DMA – On-Chip Enhanced DMA Controller (EDMA) has Three Third-Party Transfer Controllers (TPTC) and One Third-Party Channel Controller (TPCC), Which Supports Up to 64 Programmable Logical Channels and Eight QDMA Channels. EDMA is Used for: • Transfers to/from On-Chip Memories • Transfers to/from External Storage (EMIF, General-Purpose Memory Controller, Slave Peripherals) 1.2 • • • • • • Inter-Processor Communication (IPC) – Integrates Hardware-Based Mailbox for IPC and Spinlock for Process Synchronization Between the Cortex-A8, PRCM, and Each PRU • Mailbox Registers that Generate Interrupts – Four Initiators (Cortex-A8, PRCM, PRU0, PRU1) • Spinlock has 128 Software-Assigned Lock Registers • Security – Crypto Hardware accelerators (AES, SHA, PKA, RNG) • Boot Modes – Boot Mode is Selected via Boot Configuration Pins Latched on the Rising Edge of the PWRONRSTn Reset Input Pin • Packages: – 298-Pin S-PBGA-N298 package (ZCE Suffix), 0.65-mm Ball Pitch – 324-Pin S-PBGA-N324 package (ZCZ Suffix), 0.80-mm Ball Pitch Applications Gaming Peripherals Home and Industrial Automation Consumer Medical Appliances Printers Smart Toll Systems 1.3 www.ti.com • • • • Connected Vending Machines Weighing Scales Educational Consoles Advanced Toys Description The AM335x microprocessors, based on the ARM Cortex-A8, are enhanced with image, graphics processing, peripherals and industrial interface options such as EtherCAT and PROFIBUS. The device supports the following high-level operating systems (HLOSs) that are available free of charge from TI: • Linux® • Windows® CE • Android™ The AM335x microrocessor contains these subsystems: • Microprocessor unit (MPU) subsystem based on the ARM Cortex-A8 microprocessor. • POWERVR SGX™ Graphics Accelerator subsystem for 3D graphics acceleration to support display and gaming effects. • Programmable Real-Time Unit Subsystem (PRUSS) enables the user to create a variety of digital resources beyond native peripherals of the device. In addition, the PRUSS is separate from the ARM core. This allows independent operation and clocking to give the device greater flexibility in complex system solutions. Note: The subsystem available on this device is the next-generation PRUSS (PRUSSv2). 4 Device Summary Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 1.4 Functional Block Diagram The AM335x microrocessor functional block diagram is shown in Figure 1-1. ARM Cortex-A8 275/500/600/720 MHz Graphics PowerVR SGX 3D GFX 32K/32K L1 w/SED 256K L2 w/ECC Crypto 176K ROM 64K RAM 64K shared RAM Display 24-bit LCD controller (WXGA) Touch screen controller PRU subsystem 12K RAM PRU x2 w/SED 200 MHz 8K/8K w/SED Peripherals L3/L4 interconnect System UART x6 SPI x2 eDMA Timers x8 WDT ADC (8 channel) 12-bit SAR RTC eHRPWM x3 eQEP x3 Crystal Oscillator x2 2 I C x3 McASP x2 (4 channel) CAN x2 (Ver. 2 A and B) USB 2.0 HS OTG + PHY x2 eCAP x3 JTAG/ETB Parallel MMC/SD/ SDIO x3 GPIO PRODUCT PREVIEW Serial PRCM EMAC (2-port) 10M/100M/1G IEEE1588, and switch (MII, RMII, RGMII) Memory interface mDDR(LPDDR) / DDR2 / DDR3 (16-bit, 200 / 266 / 303 MHz) NAND/NOR (16-bit ECC) Figure 1-1. AM335x Functional Block Diagram Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Device Summary 5 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 ........................................ 1 1.1 Features .............................................. 1 1.2 Applications .......................................... 4 1.3 Description ........................................... 4 1.4 Functional Block Diagram ............................ 5 Revision History .............................................. 7 2 Terminal Description ................................... 9 2.1 Pin Assignments ..................................... 9 2.2 Ball Characteristics ................................. 17 2.3 Signal Description .................................. 49 3 Device Operating Conditions ....................... 77 3.1 Absolute Maximum Ratings ........................ 77 3.2 Recommended Operating Conditions .............. 80 3.3 DC Electrical Characteristics ....................... 83 3.4 External Capacitors ................................. 87 4 Power and Clocking ................................... 91 1 www.ti.com Device Summary 5 ..................................... 91 ................................ 96 Peripheral Information and Timings ............. 102 5.1 Parameter Information ............................ 102 4.1 Power Supplies 4.2 Clock Specifications 5.2 Recommended Clock and Control Signal Transition Behavior ........................................... 102 Ethernet Media Access Controller (EMAC)/Switch ..................................................... 103 5.3 6 7 ....................... ............................ Device and Documentation Support ............. 6.1 Device Support .................................... 6.2 Documentation Support ........................... 5.4 External Memory Interfaces 5.5 LCD Controller (LCDC) 110 172 188 188 189 Mechanical Packaging and Orderable Information ............................................ 191 7.1 7.2 7.3 ....... Via Channel ....................................... Packaging Information ............................ Thermal Data for ZCE and ZCZ Packages 191 191 191 PRODUCT PREVIEW 6 Contents Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision A (January 2012) to Revision B Global: deleted references to Embedded Trace Module (ETM) ............................................................... Changes from Original (October 2011) to Revision A • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 1 Page Changed ARM speeds features list item .......................................................................................... 1 Changed I2C ports features list item .............................................................................................. 1 Changed Memory device configurations features list item ..................................................................... 1 Changed Timers features list item ................................................................................................. 3 Changed Functional block diagram figure ........................................................................................ 5 Changed paragraph ................................................................................................................ 17 Added paragraphs .................................................................................................................. 49 Changed VDD_MPU parameter description .................................................................................... 77 Changed USB0_ID and USB1_ID parameter descriptions ................................................................... 77 Changed footnote .................................................................................................................. 77 Added VDD_CORE OPP100/OPP50 descriptions and values ............................................................... 79 Changed footnote .................................................................................................................. 79 Added footnote ...................................................................................................................... 79 Changed OPP120 Extended POH value ........................................................................................ 80 Changed OPP50 VDD_CORE value ............................................................................................ 80 Added VDD_CORE OPP100/OPP50 descriptions and values ............................................................... 80 Changed DDR2 and mDDR values for Turbo, OPP120, and OPP100 ..................................................... 82 Added footnote ...................................................................................................................... 82 Added footnote ...................................................................................................................... 82 Changed DDR2 and mDDR values for OPP100 ............................................................................... 82 Added footnote ...................................................................................................................... 82 Added footnote ...................................................................................................................... 82 Changed footnote .................................................................................................................. 88 Changed paragraph ................................................................................................................ 90 Added footnote ...................................................................................................................... 91 Added footnote ...................................................................................................................... 92 Added footnote ...................................................................................................................... 93 Added footnote ...................................................................................................................... 94 Added footnote ...................................................................................................................... 95 Changed paragraph ................................................................................................................ 95 Added paragraphs .................................................................................................................. 95 Added paragraphs ................................................................................................................ 102 Added paragraphs ................................................................................................................ 132 Added mDDR(LPDDR) Routing Guidelines section .......................................................................... 132 Changed paragraph .............................................................................................................. 142 Changed table ..................................................................................................................... 142 Added footnote .................................................................................................................... 142 Changed figure .................................................................................................................... 142 Changed paragraph .............................................................................................................. 142 Changed figure and figure title .................................................................................................. 144 Added figure ....................................................................................................................... 144 Changed paragraph .............................................................................................................. 145 Changed parameter 4 MIN and MAX values and added footnote .......................................................... 145 Changed footnote ................................................................................................................. 145 Changed footnote ................................................................................................................. 145 Changed layer descriptions ...................................................................................................... 145 Changed parameter 3 description and MIN value and parameter 5 description ......................................... 146 Added footnote .................................................................................................................... 146 Changed paragraph .............................................................................................................. 148 Changed figure .................................................................................................................... 148 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Contents 7 PRODUCT PREVIEW • Page AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 • • • • • • • • • • • • • • • • • • • • • www.ti.com Changed parameter 1 description and MIN value ............................................................................ Changed parameter 2 description and MIN value ............................................................................ Changed footnotes ................................................................................................................ Deleted parameter 4 MIN value ................................................................................................. Changed parameter 9 description and MIN value ............................................................................ Changed parameter 10 description and MIN value .......................................................................... Changed table ..................................................................................................................... Changed table ..................................................................................................................... Changed paragraph .............................................................................................................. Changed footnotes ................................................................................................................ Changed parameter 3 description and MIN/MAX values .................................................................... Added paragraph .................................................................................................................. Added table ........................................................................................................................ Changed parameter 1 description .............................................................................................. Changed footnote ................................................................................................................. Changed figure .................................................................................................................... Changed footnote ................................................................................................................. Changed footnote ................................................................................................................. Changed footnote ................................................................................................................. Added DDR3 Routing Guidelines section ..................................................................................... Added paragraph .................................................................................................................. 148 148 148 149 149 149 149 149 150 150 150 150 150 152 152 153 153 153 153 154 191 PRODUCT PREVIEW 8 Contents Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2 Terminal Description 2.1 Pin Assignments NOTE The terms "ball", "pin", and "terminal" are used interchangeably throughout the document. An attempt is made to use "ball" only when referring to the physical package. 2.1.1 ZCE Package Pin Maps (Top View) PRODUCT PREVIEW The pin maps below show the pin assignments on the ZCE package in three sections (left, middle, and right). Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 9 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-1. ZCE Pin Map [Section Left - Top View] PRODUCT PREVIEW A B C D E F 19 VSS I2C0_SCL UART1_TXD UART1_RTSn UART0_RXD UART0_CTSn 18 SPI0_SCLK SPI0_D0 I2C0_SDA UART1_RXD ECAP0_IN_PWM0_OUT UART0_RTSn 17 SPI0_CS0 SPI0_D1 EXTINTn XXXX UART1_CTSn UART0_TXD 16 WARMRSTn SPI0_CS1 XXXX XXXX XXXX VDDS 15 EMU0 XDMA_EVENT_INTR1 XDMA_EVENT_INTR0 XXXX PWRONRSTn XXXX 14 TDO TCK TMS EMU1 XXXX VDDSHV6 13 TRSTn TDI CAP_VBB_MPU CAP_VDD_SRAM_MPU VDDSHV6 VSS 12 AIN7 AIN5 VDDS_SRAM_MPU_BB VDDS VDDSHV6 VSS 11 AIN1 AIN3 XXXX XXXX VDDSHV6 VDD_CORE 10 AIN6 CAP_VDD_SRAM_CORE VDDS_SRAM_CORE_BG VSS VSS XXXX 9 VREFP VREFN XXXX XXXX VSS VDD_CORE 8 AIN2 AIN0 AIN4 VSSA_ADC VSS VSS 7 RTC_KALDO_ENn RTC_PWRONRSTn PMIC_POWER_EN VDDA_ADC VSS VSS 6 RTC_XTALIN RESERVED VDDS_RTC CAP_VDD_RTC XXXX VSS 5 RTC_XTALOUT EXT_WAKEUP VDDS_PLL_DDR XXXX DDR_A4 XXXX 4 DDR_WEn DDR_BA2 XXXX XXXX XXXX DDR_A12 3 DDR_BA0 DDR_A3 DDR_A8 XXXX DDR_A15 DDR_A0 2 DDR_A5 DDR_A9 DDR_CK DDR_A7 DDR_A10 DDR_RASn 1 VSS DDR_A6 DDR_CKn DDR_A2 DDR_BA1 DDR_CASn Pin map section location Left 10 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com G H J K L M 19 MMC0_CLK MMC0_DAT3 MII1_COL MII1_RX_ER MII1_RX_DV MII1_RX_CLK 18 MMC0_DAT0 MMC0_DAT2 MII1_CRS RMII1_REF_CLK MII1_TXD0 MII1_TXD1 17 MMC0_CMD MMC0_DAT1 XXXX MII1_TX_EN XXXX MII1_TXD3 16 USB0_DRVVBUS VDDS_PLL_MPU XXXX VDD_CORE XXXX VDDS 15 VDDSHV4 VDDSHV4 VSS VDD_CORE VSS VDDSHV5 14 XXXX VDDSHV4 VSS XXXX VSS VDDSHV5 13 XXXX VDD_CORE VDD_CORE XXXX VDD_CORE VDD_CORE 12 VSS VDD_CORE VDD_CORE VSS VDD_CORE VDD_CORE 11 VDD_CORE VSS VSS VSS VSS VSS 10 XXXX VSS XXXX XXXX XXXX VSS 9 VDD_CORE VSS VSS VSS VSS VSS 8 VSS VDD_CORE VDD_CORE VSS VDD_CORE VDD_CORE 7 XXXX VDD_CORE VDD_CORE XXXX VDD_CORE VDD_CORE 6 XXXX VDDS_DDR VSS XXXX VSS VDDS_DDR 5 VDDS_DDR VDDS_DDR VSS VDDS_DDR VSS VDDS_DDR 4 DDR_A11 DDR_VREF XXXX VDDS_DDR XXXX DDR_D11 3 DDR_CKE DDR_A14 XXXX DDR_DQM1 XXXX DDR_D10 2 DDR_RESETn DDR_CSn0 DDR_A1 DDR_D8 DDR_DQSn1 DDR_D12 1 DDR_ODT DDR_A13 DDR_VTP DDR_D9 DDR_DQS1 DDR_D13 PRODUCT PREVIEW Table 2-2. ZCE Pin Map [Section Middle - Top View] Pin map section location Middle Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 11 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-3. ZCE Pin Map [Section Right - Top View] PRODUCT PREVIEW N P R T U V W 19 MII1_TX_CLK MII1_RXD1 MDC USB0_VBUS USB0_DP USB0_ID VSS 18 MII1_TXD2 MII1_RXD0 VDDA3P3V_USB0 USB0_CE USB0_DM GPMC_BEn1 GPMC_WPn 17 MII1_RXD3 MDIO VDDA1P8V_USB0 XXXX GPMC_CSn3 GPMC_AD15 GPMC_AD14 16 MII1_RXD2 VSSA_USB XXXX XXXX XXXX GPMC_CLK GPMC_AD9 15 VDDSHV5 XXXX GPMC_WAIT0 XXXX GPMC_CSn2 GPMC_AD8 GPMC_AD7 14 XXXX VSS XXXX VDDS GPMC_AD6 GPMC_CSn1 GPMC_AD5 13 XXXX VSS VDDSHV1 GPMC_AD13 GPMC_AD12 GPMC_AD4 GPMC_AD3 12 VSS VSS VDDSHV1 GPMC_AD10 GPMC_AD11 GPMC_AD2 XTALOUT 11 VDD_CORE VDD_CORE VDDSHV1 XXXX XXXX VSS_OSC XTALIN 10 XXXX XXXX VSS VSS VDDS_OSC GPMC_ADVn_ALE GPMC_AD0 9 VDD_CORE VDD_CORE VDDSHV1 XXXX XXXX GPMC_AD1 GPMC_OEn_REn 8 VSS VSS VDDSHV1 VDDS_PLL_CORE_LCD GPMC_WEn GPMC_BEn0_CLE GPMC_CSn0 7 XXXX VSS VDDSHV6 LCD_HSYNC LCD_VSYNC LCD_DATA15 LCD_AC_BIAS_EN 6 XXXX VDDSHV6 XXXX VDDS LCD_DATA13 LCD_DATA12 LCD_DATA14 5 VDDS_DDR XXXX VPP XXXX LCD_DATA10 LCD_DATA11 LCD_PCLK 4 DDR_D0 DDR_D1 XXXX XXXX XXXX LCD_DATA8 LCD_DATA9 3 DDR_DQM0 DDR_D4 DDR_D7 XXXX LCD_DATA7 LCD_DATA6 LCD_DATA5 2 DDR_D14 DDR_D2 DDR_DQSn0 DDR_D6 LCD_DATA1 LCD_DATA3 LCD_DATA4 1 DDR_D15 DDR_D3 DDR_DQS0 DDR_D5 LCD_DATA0 LCD_DATA2 VSS Pin map section location Right 12 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.1.2 ZCZ Package Pin Maps (Top View) PRODUCT PREVIEW The pin maps below show the pin assignments on the ZCZ package in three sections (left, middle, and right). Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 13 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-4. ZCZ Pin Map [Section Left - Top View] PRODUCT PREVIEW A B C D E F 18 VSS EXTINTn ECAP0_IN_PWM0_OUT UART1_CTSn UART0_CTSn MMC0_DAT2 17 SPI0_SCLK SPI0_D0 I2C0_SDA UART1_RTSn UART0_RTSn MMC0_DAT3 16 SPI0_CS0 SPI0_D1 I2C0_SCL UART1_RXD UART0_TXD USB0_DRVVBUS 15 XDMA_EVENT_INTR0 PWRONRSTn SPI0_CS1 UART1_TXD UART0_RXD USB1_DRVVBUS 14 MCASP0_AHCLKX EMU1 EMU0 XDMA_EVENT_INTR1 VDDS VDDSHV6 13 MCASP0_ACLKX MCASP0_FSX MCASP0_FSR MCASP0_AXR1 VDDSHV6 VDD_MPU 12 TCK MCASP0_ACLKR MCASP0_AHCLKR MCASP0_AXR0 VDDSHV6 VDD_MPU 11 TDO TDI TMS CAP_VDD_SRAM_MPU VDDSHV6 VDD_MPU 10 WARMRSTn TRSTn CAP_VBB_MPU VDDS_SRAM_MPU_BB VDDSHV6 VDD_MPU 9 VREFN VREFP AIN7 CAP_VDD_SRAM_CORE VDDS_SRAM_CORE_BG VDDS 8 AIN6 AIN5 AIN4 VDDA_ADC VSSA_ADC VSS 7 AIN3 AIN2 AIN1 VDDS_RTC VDDS_PLL_DDR VDD_CORE 6 RTC_XTALIN AIN0 PMIC_POWER_EN CAP_VDD_RTC VDDS VDD_CORE 5 VSS_RTC RTC_PWRONRSTn EXT_WAKEUP DDR_A6 VDDS_DDR VDDS_DDR 4 RTC_XTALOUT RTC_KALDO_ENn DDR_BA0 DDR_A8 DDR_A2 DDR_A10 3 RESERVED DDR_BA2 DDR_A3 DDR_A15 DDR_A12 DDR_A0 2 VDD_MPU_MON DDR_WEn DDR_A4 DDR_CK DDR_A7 DDR_A11 1 VSS DDR_A5 DDR_A9 DDR_CKn DDR_BA1 DDR_CASn Pin map section location Left 14 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com G H J K L M 18 MMC0_CMD RMII1_REF_CLK MII1_TXD3 MII1_TX_CLK MII1_RX_CLK MDC 17 MMC0_CLK MII1_CRS MII1_RX_DV MII1_TXD0 MII1_RXD3 MDIO 16 MMC0_DAT0 MII1_COL MII1_TX_EN MII1_TXD1 MII1_RXD2 MII1_RXD0 15 MMC0_DAT1 VDDS_PLL_MPU MII1_RX_ER MII1_TXD2 MII1_RXD1 USB0_CE 14 VDDSHV6 VDDSHV4 VDDSHV4 VDDSHV5 VDDSHV5 VSSA_USB 13 VDD_MPU VDD_MPU VDD_MPU VDDS VSS VDD_CORE 12 VSS VSS VDD_CORE VDD_CORE VSS VSS 11 VSS VDD_CORE VSS VSS VSS VDD_CORE 10 VDD_CORE VSS VSS VSS VSS VSS 9 VSS VSS VSS VSS VDD_CORE VSS 8 VSS VSS VSS VDD_CORE VDD_CORE VSS 7 VDD_CORE VSS VSS VSS VDD_CORE VSS 6 VDD_CORE VSS VSS VDD_CORE VDD_CORE VSS 5 VDDS_DDR VDDS_DDR VDDS_DDR VDDS_DDR VDDS_DDR VPP 4 DDR_RASn DDR_A14 DDR_VREF DDR_D12 DDR_D14 DDR_D1 3 DDR_CKE DDR_A13 DDR_VTP DDR_D11 DDR_D13 DDR_D0 2 DDR_RESETn DDR_CSn0 DDR_DQM1 DDR_D10 DDR_DQSn1 DDR_DQM0 1 DDR_ODT DDR_A1 DDR_D8 DDR_D9 DDR_DQS1 DDR_D15 PRODUCT PREVIEW Table 2-5. ZCZ Pin Map [Section Middle - Top View] Pin map section location Middle Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 15 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-6. ZCZ Pin Map [Section Right - Top View] PRODUCT PREVIEW N P R T U V 18 USB0_DM USB1_CE USB1_DM USB1_VBUS GPMC_BEn1 VSS 17 USB0_DP USB1_ID USB1_DP GPMC_WAIT0 GPMC_WPn GPMC_A11 16 VDDA1P8V_USB0 USB0_ID VDDA1P8V_USB1 GPMC_A10 GPMC_A9 GPMC_A8 15 VDDA3P3V_USB0 USB0_VBUS VDDA3P3V_USB1 GPMC_A7 GPMC_A6 GPMC_A5 14 VSSA_USB VDDS GPMC_A4 GPMC_A3 GPMC_A2 GPMC_A1 13 VDD_CORE VDDSHV3 GPMC_A0 GPMC_CSn3 GPMC_AD15 GPMC_AD14 12 VDD_CORE VDDSHV3 GPMC_AD13 GPMC_AD12 GPMC_AD11 GPMC_CLK 11 VSS VDDSHV2 VDDS_OSC GPMC_AD10 XTALOUT VSS_OSC 10 VSS VDDSHV2 VDDS_PLL_CORE_LCD GPMC_AD9 GPMC_AD8 XTALIN 9 VDD_CORE VDDS GPMC_AD6 GPMC_AD7 GPMC_CSn1 GPMC_CSn2 8 VDD_CORE VDDSHV1 GPMC_AD2 GPMC_AD3 GPMC_AD4 GPMC_AD5 7 VSS VDDSHV1 GPMC_ADVn_ALE GPMC_OEn_REn GPMC_AD0 GPMC_AD1 6 VDDS VDDSHV6 LCD_AC_BIAS_EN GPMC_BEn0_CLE GPMC_WEn GPMC_CSn0 5 VDDSHV6 VDDSHV6 LCD_HSYNC LCD_DATA15 LCD_VSYNC LCD_PCLK 4 DDR_D5 DDR_D7 LCD_DATA3 LCD_DATA7 LCD_DATA11 LCD_DATA14 3 DDR_D4 DDR_D6 LCD_DATA2 LCD_DATA6 LCD_DATA10 LCD_DATA13 2 DDR_D3 DDR_DQSn0 LCD_DATA1 LCD_DATA5 LCD_DATA9 LCD_DATA12 1 DDR_D2 DDR_DQS0 LCD_DATA0 LCD_DATA4 LCD_DATA8 VSS Pin map section location Right 16 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.2 Ball Characteristics 5. 6. 7. 8. Note: The default mode is the mode at the release of the reset; also see the RESET REL. MODE column. (b) Modes 1 to 7 are possible modes for alternate functions. On each terminal, some modes are effectively used for alternate functions, while some modes are not used and do not correspond to a functional configuration. TYPE: Signal direction – I = Input – O = Output – I/O = Input/Output – D = Open drain – DS = Differential – A = Analog – PWR = Power – GND = Ground Note: In the safe_mode, the buffer is configured in high-impedance. BALL RESET STATE: The state of the terminal at the power-on reset. – 0: The buffer drives VOL (pulldown/pullup resistor not activated) 0(PD): The buffer drives VOL with an active pulldown resistor – 1: The buffer drives VOH (pulldown/pullup resistor not activated) 1(PU): The buffer drives VOH with an active pullup resistor – Z: High-impedance – L: High-impedance with an active pulldown resistor – H : High-impedance with an active pullup resistor BALL RESET REL. STATE: The state of the terminal at the release of the System Control Module reset (PRCM CORE_RSTPWRON_RET reset signal). – 0: The buffer drives VOL (pulldown/pullup resistor not activated) 0(PD): The buffer drives VOL with an active pulldown resistor – 1: The buffer drives VOH (pulldown/pullup resistor not activated) 1(PU): The buffer drives VOH with an active pullup resistor – Z: High-impedance. – L: High-impedance with an active pulldown resistor – H : High-impedance with an active pullup resistor RESET REL. MODE: The mode is automatically configured at the release of the System Control Module reset (PRCM CORE_RSTPWRON_RET reset signal). Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 17 PRODUCT PREVIEW The AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73) and this document may reference internal signal names when discussing peripheral input and output signals since many of the AM335x package terminals can be multiplexed to one of several peripheral signals. The following table has a Pin Name column that lists all device terminal names and a Signal Name column that lists all internal signal names multiplexed to each terminal which provides a cross reference of internal signal names to terminal names. This table also identifies other important terminal characteristics. 1. BALL NUMBER: Package ball number(s) associated with each signal(s). 2. PIN NAME: The name of the package pin or terminal. Note: The table does not take into account subsystem terminal multiplexing options. 3. SIGNAL NAME: The signal name for that pin in the mode being used. 4. MODE: Multiplexing mode number. (a) Mode 0 is the primary mode; this means that when mode 0 is set, the function mapped on the terminal corresponds to the name of the terminal. There is always a function mapped on the primary mode. Notice that primary mode is not necessarily the default mode. AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 9. POWER: The voltage supply that powers the terminal’s I/O buffers. 10. HYS: Indicates if the input buffer is with hysteresis. 11. BUFFER STRENGTH: Drive strength of the associated output buffer. 12. PULLUP/DOWN TYPE: Denotes the presence of an internal pullup or pulldown resistor. Pullup and pulldown resistors can be enabled or disabled via software. 13. I/O CELL: IO cell information. Note: Configuring two terminals to the same input signal is not supported as it can yield unexpected results. This can be easily prevented with the proper software configuration. PRODUCT PREVIEW 18 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) PIN NAME [2] SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] B8 B6 AIN0 AIN0 0 A (13) Z Z 0 VDDA_ADC / VDDA_ADC NA 50 NA Analog A11 C7 AIN1 AIN1 0 A (12) Z Z 0 VDDA_ADC / VDDA_ADC NA 50 NA Analog A8 B7 AIN2 AIN2 0 A (12) Z Z 0 VDDA_ADC / VDDA_ADC NA 50 NA Analog B11 A7 AIN3 AIN3 0 A (11) Z Z 0 VDDA_ADC / VDDA_ADC NA 50 NA Analog C8 C8 AIN4 AIN4 0 A (11) Z Z 0 VDDA_ADC / VDDA_ADC NA 50 NA Analog B12 B8 AIN5 AIN5 0 A Z Z 0 VDDA_ADC / VDDA_ADC NA NA NA Analog A10 A8 AIN6 AIN6 0 A Z Z 0 VDDA_ADC / VDDA_ADC NA NA NA Analog A12 C9 AIN7 AIN7 0 A Z Z 0 VDDA_ADC / VDDA_ADC NA NA NA Analog C13 C10 CAP_VBB_MPU CAP_VBB_MPU NA A D6 D6 CAP_VDD_RTC CAP_VDD_RTC NA A B10 D9 CAP_VDD_SRAM_CORE CAP_VDD_SRAM_CORE NA A D13 D11 CAP_VDD_SRAM_MPU CAP_VDD_SRAM_MPU NA A F3 F3 DDR_A0 ddr_a0 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL J2 H1 DDR_A1 ddr_a1 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL D1 E4 DDR_A2 ddr_a2 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL B3 C3 DDR_A3 ddr_a3 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL E5 C2 DDR_A4 ddr_a4 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL A2 B1 DDR_A5 ddr_a5 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL B1 D5 DDR_A6 ddr_a6 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL D2 E2 DDR_A7 ddr_a7 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL C3 D4 DDR_A8 ddr_a8 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL B2 C1 DDR_A9 ddr_a9 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL E2 F4 DDR_A10 ddr_a10 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL G4 F2 DDR_A11 ddr_a11 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 19 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] PIN NAME [2] SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] PRODUCT PREVIEW F4 E3 DDR_A12 ddr_a12 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL H1 H3 DDR_A13 ddr_a13 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL H3 H4 DDR_A14 ddr_a14 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL E3 D3 DDR_A15 ddr_a15 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL A3 C4 DDR_BA0 ddr_ba0 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL E1 E1 DDR_BA1 ddr_ba1 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL B4 B3 DDR_BA2 ddr_ba2 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL F1 F1 DDR_CASn ddr_casn 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL C2 D2 DDR_CK ddr_ck 0 O L 0 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL G3 G3 DDR_CKE ddr_cke 0 O L 0 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL C1 D1 DDR_CKn ddr_nck 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL H2 H2 DDR_CSn0 ddr_csn0 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL N4 M3 DDR_D0 ddr_d0 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL P4 M4 DDR_D1 ddr_d1 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL P2 N1 DDR_D2 ddr_d2 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL P1 N2 DDR_D3 ddr_d3 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL P3 N3 DDR_D4 ddr_d4 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL T1 N4 DDR_D5 ddr_d5 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL T2 P3 DDR_D6 ddr_d6 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL R3 P4 DDR_D7 ddr_d7 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL K2 J1 DDR_D8 ddr_d8 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL K1 K1 DDR_D9 ddr_d9 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL M3 K2 DDR_D10 ddr_d10 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL 20 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) PIN NAME [2] SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] M4 K3 DDR_D11 ddr_d11 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL M2 K4 DDR_D12 ddr_d12 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL M1 L3 DDR_D13 ddr_d13 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL N2 L4 DDR_D14 ddr_d14 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL N1 M1 DDR_D15 ddr_d15 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL N3 M2 DDR_DQM0 ddr_dqm0 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL K3 J2 DDR_DQM1 ddr_dqm1 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL R1 P1 DDR_DQS0 ddr_dqs0 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL L1 L1 DDR_DQS1 ddr_dqs1 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL R2 P2 DDR_DQSn0 ddr_dqsn0 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL L2 L2 DDR_DQSn1 ddr_dqsn1 0 I/O L Z 0 VDDS_DDR / VDDS_DDR Yes 8 PU/PD LVCMOS/SSTL/ HSTL G1 G1 DDR_ODT ddr_odt 0 O L 0 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL F2 G4 DDR_RASn ddr_rasn 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL G2 G2 DDR_RESETn ddr_resetn 0 O L 0 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL H4 J4 DDR_VREF ddr_vref 0 AP (9) NA NA NA VDDS_DDR / VDDS_DDR NA NA NA Analog J1 J3 DDR_VTP ddr_vtp 0 I NA NA NA VDDS_DDR / VDDS_DDR NA NA NA Analog A4 B2 DDR_WEn ddr_wen 0 O H 1 0 VDDS_DDR / VDDS_DDR NA 8 PU/PD LVCMOS/SSTL/ HSTL E18 C18 ECAP0_IN_PWM0_OUT eCAP0_in_PWM0_out 0 I/O Z L 7 4 PU/PD LVCMOS 1 O VDDSHV6 / VDDSHV6 Yes uart3_txd spi1_cs1 2 I/O pr1_ecap0_ecap_capin_apwm_o 3 I/O spi1_sclk 4 I/O mmc0_sdwp 5 I xdma_event_intr2 6 I gpio0_7 7 I/O EMU0 0 I/O H H 0 6 PU/PD LVCMOS 7 I/O VDDSHV6 / VDDSHV6 Yes gpio3_7 A15 C14 EMU0 (10) Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 21 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] D14 B14 PIN NAME [2] EMU1 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] EMU1 0 I/O gpio3_8 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] H H 0 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS PRODUCT PREVIEW C17 B18 EXTINTn nNMI 0 I Z H 0 VDDSHV6 / VDDSHV6 Yes NA PU/PD LVCMOS B5 C5 EXT_WAKEUP EXT_WAKEUP 0 I L L 0 VDDS_RTC / VDDS_RTC Yes NA NA LVCMOS NA R13 GPMC_A0 gpmc_a0 0 O L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS gmii2_txen 1 O rgmii2_tctl 2 O rmii2_txen 3 O gpmc_a16 4 O pr1_mii_mt1_clk 5 I ehrpwm1_tripzone_input 6 I gpio1_16 7 I/O gpmc_a1 0 O L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS gmii2_rxdv 1 I rgmii2_rctl 2 I mmc2_dat0 3 I/O gpmc_a17 4 O pr1_mii1_txd3 5 O ehrpwm0_synco 6 O gpio1_17 7 I/O gpmc_a2 0 O L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS gmii2_txd3 1 O rgmii2_td3 2 O mmc2_dat1 3 I/O gpmc_a18 4 O pr1_mii1_txd2 5 O ehrpwm1A 6 O gpio1_18 7 I/O gpmc_a3 0 O L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS gmii2_txd2 1 O rgmii2_td2 2 O mmc2_dat2 3 I/O gpmc_a19 4 O pr1_mii1_txd1 5 O ehrpwm1B 6 O gpio1_19 7 I/O NA NA NA 22 V14 U14 T14 GPMC_A1 GPMC_A2 GPMC_A3 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) NA NA NA NA R14 V15 U15 T15 PIN NAME [2] GPMC_A4 GPMC_A5 GPMC_A6 GPMC_A7 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_a4 0 O gmii2_txd1 1 O rgmii2_td1 2 O rmii2_txd1 3 O gpmc_a20 4 O pr1_mii1_txd0 5 O eQEP1A_in 6 I gpio1_20 7 I/O gpmc_a5 0 O gmii2_txd0 1 O rgmii2_td0 2 O rmii2_txd0 3 O gpmc_a21 4 O pr1_mii1_rxd3 5 I eQEP1B_in 6 I gpio1_21 7 I/O gpmc_a6 0 O gmii2_txclk 1 I rgmii2_tclk 2 O mmc2_dat4 3 I/O gpmc_a22 4 O pr1_mii1_rxd2 5 I eQEP1_index 6 I/O gpio1_22 7 I/O gpmc_a7 0 O gmii2_rxclk 1 I rgmii2_rclk 2 I mmc2_dat5 3 I/O gpmc_a23 4 O pr1_mii1_rxd1 5 I eQEP1_strobe 6 I/O gpio1_23 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 23 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] NA NA PRODUCT PREVIEW NA NA W10 V9 24 V16 U16 T16 V17 U7 V7 PIN NAME [2] GPMC_A8 GPMC_A9 GPMC_A10 GPMC_A11 GPMC_AD0 GPMC_AD1 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_a8 0 O gmii2_rxd3 1 I rgmii2_rd3 2 I mmc2_dat6 3 I/O gpmc_a24 4 O pr1_mii1_rxd0 5 I mcasp0_aclkx 6 I/O gpio1_24 7 I/O gpmc_a9 0 O gmii2_rxd2 1 I rgmii2_rd2 2 I mmc2_dat7 3 I/O gpmc_a25 4 O pr1_mii_mr1_clk 5 I mcasp0_fsx 6 I/O gpio1_25 7 I/O gpmc_a10 0 O gmii2_rxd1 1 I rgmii2_rd1 2 I rmii2_rxd1 3 I gpmc_a26 4 O pr1_mii1_rxdv 5 I mcasp0_axr0 6 I/O gpio1_26 7 I/O gpmc_a11 0 O gmii2_rxd0 1 I rgmii2_rd0 2 I rmii2_rxd0 3 I gpmc_a27 4 O pr1_mii1_rxer 5 I mcasp0_axr1 6 I/O gpio1_27 7 I/O gpmc_ad0 0 I/O mmc1_dat0 1 I/O gpio1_0 7 I/O gpmc_ad1 0 I/O mmc1_dat1 1 I/O gpio1_1 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) V12 W13 V13 W14 U14 W15 V15 W16 R8 T8 U8 V8 R9 T9 U10 T10 PIN NAME [2] GPMC_AD2 GPMC_AD3 GPMC_AD4 GPMC_AD5 GPMC_AD6 GPMC_AD7 GPMC_AD8 GPMC_AD9 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_ad2 0 I/O mmc1_dat2 1 I/O gpio1_2 7 I/O gpmc_ad3 0 I/O mmc1_dat3 1 I/O gpio1_3 7 I/O gpmc_ad4 0 I/O mmc1_dat4 1 I/O gpio1_4 7 I/O gpmc_ad5 0 I/O mmc1_dat5 1 I/O gpio1_5 7 I/O gpmc_ad6 0 I/O mmc1_dat6 1 I/O gpio1_6 7 I/O gpmc_ad7 0 I/O mmc1_dat7 1 I/O gpio1_7 7 I/O gpmc_ad8 0 I/O lcd_data23 1 O mmc1_dat0 2 I/O mmc2_dat4 3 I/O ehrpwm2A 4 O pr1_mii_mt0_clk 5 I gpio0_22 7 I/O gpmc_ad9 0 I/O lcd_data22 1 O mmc1_dat1 2 I/O mmc2_dat5 3 I/O ehrpwm2B 4 O pr1_mii0_col 5 I gpio0_23 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 25 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] T12 U12 PRODUCT PREVIEW U13 T13 W17 26 T11 U12 T12 R12 V13 PIN NAME [2] GPMC_AD10 GPMC_AD11 GPMC_AD12 GPMC_AD13 GPMC_AD14 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_ad10 0 I/O lcd_data21 1 O mmc1_dat2 2 I/O mmc2_dat6 3 I/O ehrpwm2_tripzone_input 4 I pr1_mii0_txen 5 O gpio0_26 7 I/O gpmc_ad11 0 I/O lcd_data20 1 O mmc1_dat3 2 I/O mmc2_dat7 3 I/O ehrpwm0_synco 4 O pr1_mii0_txd3 5 O gpio0_27 7 I/O gpmc_ad12 0 I/O lcd_data19 1 O mmc1_dat4 2 I/O mmc2_dat0 3 I/O eQEP2A_in 4 I pr1_mii0_txd2 5 O pr1_pru0_pru_r30_14 6 O gpio1_12 7 I/O gpmc_ad13 0 I/O lcd_data18 1 O mmc1_dat5 2 I/O mmc2_dat1 3 I/O eQEP2B_in 4 I pr1_mii0_txd1 5 O pr1_pru0_pru_r30_15 6 O gpio1_13 7 I/O gpmc_ad14 0 I/O lcd_data17 1 O mmc1_dat6 2 I/O mmc2_dat2 3 I/O eQEP2_index 4 I/O pr1_mii0_txd0 5 O pr1_pru0_pru_r31_14 6 I gpio1_14 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) V17 V10 V8 V18 V16 W8 U13 R7 T6 U18 V12 V6 PIN NAME [2] GPMC_AD15 GPMC_ADVn_ALE GPMC_BEn0_CLE GPMC_BEn1 GPMC_CLK GPMC_CSn0 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_ad15 0 I/O lcd_data16 1 O mmc1_dat7 2 I/O mmc2_dat3 3 I/O eQEP2_strobe 4 I/O pr1_ecap0_ecap_capin_apwm_o 5 I/O pr1_pru0_pru_r31_15 6 I gpio1_15 7 I/O gpmc_advn_ale 0 O timer4 2 I/O gpio2_2 7 I/O gpmc_be0n_cle 0 O timer5 2 I/O gpio2_5 7 I/O gpmc_be1n 0 O gmii2_col 1 I gpmc_csn6 2 O mmc2_dat3 3 I/O gpmc_dir 4 O pr1_mii1_rxlink 5 I mcasp0_aclkr 6 I/O gpio1_28 7 I/O gpmc_clk 0 I/O lcd_memory_clk 1 O gpmc_wait1 2 I mmc2_clk 3 I/O pr1_mii1_crs 4 I pr1_mdio_mdclk 5 O mcasp0_fsr 6 I/O gpio2_1 7 I/O gpmc_csn0 0 O gpio1_29 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV3 Yes 6 PU/PD LVCMOS L L 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 27 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] V14 U15 PRODUCT PREVIEW U17 W9 R15 U8 28 U9 V9 T13 T7 T17 U6 PIN NAME [2] GPMC_CSn1 GPMC_CSn2 GPMC_CSn3 GPMC_OEn_REn GPMC_WAIT0 GPMC_WEn SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_csn1 0 O gpmc_clk 1 I/O mmc1_clk 2 I/O pr1_edio_data_in6 3 I pr1_edio_data_out6 4 O pr1_pru1_pru_r30_12 5 O pr1_pru1_pru_r31_12 6 I gpio1_30 7 I/O gpmc_csn2 0 O gpmc_be1n 1 O mmc1_cmd 2 I/O pr1_edio_data_in7 3 I pr1_edio_data_out7 4 O pr1_pru1_pru_r30_13 5 O pr1_pru1_pru_r31_13 6 I gpio1_31 7 I/O gpmc_csn3 0 O mmc2_cmd 3 I/O pr1_mii0_crs 4 I pr1_mdio_data 5 I/O EMU4 6 I/O gpio2_0 7 I/O gpmc_oen_ren 0 O timer7 2 I/O gpio2_3 7 I/O gpmc_wait0 0 I gmii2_crs 1 I gpmc_csn4 2 O rmii2_crs_dv 3 I mmc1_sdcd 4 I pr1_mii1_col 5 I uart4_rxd 6 I gpio0_30 7 I/O gpmc_wen 0 O timer6 2 I/O gpio2_4 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV2 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV3 Yes 6 PU/PD LVCMOS H H 7 VDDSHV1 / VDDSHV1 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) W18 C18 B19 W7 U1 U17 C17 C16 R6 R1 PIN NAME [2] GPMC_WPn I2C0_SDA I2C0_SCL LCD_AC_BIAS_EN LCD_DATA0 (3) SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gpmc_wpn 0 O gmii2_rxerr 1 I gpmc_csn5 2 O rmii2_rxerr 3 I mmc2_sdcd 4 I pr1_mii1_txen 5 O uart4_txd 6 O gpio0_31 7 I/O I2C0_SDA 0 I/OD timer4 1 I/O uart2_ctsn 2 I eCAP2_in_PWM2_out 3 I/O gpio3_5 7 I/O I2C0_SCL 0 I/OD timer7 1 I/O uart2_rtsn 2 O eCAP1_in_PWM1_out 3 I/O gpio3_6 7 I/O lcd_ac_bias_en 0 O gpmc_a11 1 O pr1_mii1_crs 2 I pr1_edio_data_in5 3 I pr1_edio_data_out5 4 O pr1_pru1_pru_r30_11 5 O pr1_pru1_pru_r31_11 6 I gpio2_25 7 I/O lcd_data0 0 I/O gpmc_a0 1 O pr1_mii_mt0_clk 2 I ehrpwm2A 3 O pr1_pru1_pru_r30_0 5 O pr1_pru1_pru_r31_0 6 I gpio2_6 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] H H 7 VDDSHV1 / VDDSHV3 Yes 6 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z L 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 29 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] U2 V1 PRODUCT PREVIEW V2 W2 W3 30 R2 R3 R4 T1 T2 PIN NAME [2] LCD_DATA1 (3) LCD_DATA2 (3) LCD_DATA3 (3) LCD_DATA4 (3) LCD_DATA5 (3) SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] lcd_data1 0 I/O gpmc_a1 1 O pr1_mii0_txen 2 O ehrpwm2B 3 O pr1_pru1_pru_r30_1 5 O pr1_pru1_pru_r31_1 6 I gpio2_7 7 I/O lcd_data2 0 I/O gpmc_a2 1 O pr1_mii0_txd3 2 O ehrpwm2_tripzone_input 3 I pr1_pru1_pru_r30_2 5 O pr1_pru1_pru_r31_2 6 I gpio2_8 7 I/O lcd_data3 0 I/O gpmc_a3 1 O pr1_mii0_txd2 2 O ehrpwm0_synco 3 O pr1_pru1_pru_r30_3 5 O pr1_pru1_pru_r31_3 6 I gpio2_9 7 I/O lcd_data4 0 I/O gpmc_a4 1 O pr1_mii0_txd1 2 O eQEP2A_in 3 I pr1_pru1_pru_r30_4 5 O pr1_pru1_pru_r31_4 6 I gpio2_10 7 I/O lcd_data5 0 I/O gpmc_a5 1 O pr1_mii0_txd0 2 O eQEP2B_in 3 I pr1_pru1_pru_r30_5 5 O pr1_pru1_pru_r31_5 6 I gpio2_11 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) V3 U3 V4 W4 T3 T4 U1 U2 PIN NAME [2] LCD_DATA6 (3) LCD_DATA7 (3) LCD_DATA8 (3) LCD_DATA9 (3) SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] lcd_data6 0 I/O gpmc_a6 1 O pr1_edio_data_in6 2 I eQEP2_index 3 I/O pr1_edio_data_out6 4 O pr1_pru1_pru_r30_6 5 O pr1_pru1_pru_r31_6 6 I gpio2_12 7 I/O lcd_data7 0 I/O gpmc_a7 1 O pr1_edio_data_in7 2 I eQEP2_strobe 3 I/O pr1_edio_data_out7 4 O pr1_pru1_pru_r30_7 5 O pr1_pru1_pru_r31_7 6 I gpio2_13 7 I/O lcd_data8 0 I/O gpmc_a12 1 O ehrpwm1_tripzone_input 2 I mcasp0_aclkx 3 I/O uart5_txd 4 O pr1_mii0_rxd3 5 I uart2_ctsn 6 I gpio2_14 7 I/O lcd_data9 0 I/O gpmc_a13 1 O ehrpwm0_synco 2 O mcasp0_fsx 3 I/O uart5_rxd 4 I pr1_mii0_rxd2 5 I uart2_rtsn 6 O gpio2_15 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 31 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] U5 V5 PRODUCT PREVIEW V6 U6 32 U3 U4 V2 V3 PIN NAME [2] LCD_DATA10 (3) LCD_DATA11 (3) LCD_DATA12 (3) LCD_DATA13 (3) SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] lcd_data10 0 I/O gpmc_a14 1 O ehrpwm1A 2 O mcasp0_axr0 3 I/O pr1_mii0_rxd1 5 I uart3_ctsn 6 I gpio2_16 7 I/O lcd_data11 0 I/O gpmc_a15 1 O ehrpwm1B 2 O mcasp0_ahclkr 3 I/O mcasp0_axr2 4 I/O pr1_mii0_rxd0 5 I uart3_rtsn 6 O gpio2_17 7 I/O lcd_data12 0 I/O gpmc_a16 1 O eQEP1A_in 2 I mcasp0_aclkr 3 I/O mcasp0_axr2 4 I/O pr1_mii0_rxlink 5 I uart4_ctsn 6 I gpio0_8 7 I/O lcd_data13 0 I/O gpmc_a17 1 O eQEP1B_in 2 I mcasp0_fsr 3 I/O mcasp0_axr3 4 I/O pr1_mii0_rxer 5 I uart4_rtsn 6 O gpio0_9 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) W6 V7 T7 W5 U7 V4 T5 R5 V5 U5 PIN NAME [2] LCD_DATA14 (3) LCD_DATA15 (3) LCD_HSYNC LCD_PCLK LCD_VSYNC SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] lcd_data14 0 I/O gpmc_a18 1 O eQEP1_index 2 I/O mcasp0_axr1 3 I/O uart5_rxd 4 I pr1_mii_mr0_clk 5 I uart5_ctsn 6 I gpio0_10 7 I/O lcd_data15 0 I/O gpmc_a19 1 O eQEP1_strobe 2 I/O mcasp0_ahclkx 3 I/O mcasp0_axr3 4 I/O pr1_mii0_rxdv 5 I uart5_rtsn 6 O gpio0_11 7 I/O lcd_hsync 0 O gpmc_a9 1 O pr1_edio_data_in3 3 I pr1_edio_data_out3 4 O pr1_pru1_pru_r30_9 5 O pr1_pru1_pru_r31_9 6 I gpio2_23 7 I/O lcd_pclk 0 O gpmc_a10 1 O pr1_mii0_crs 2 I pr1_edio_data_in4 3 I pr1_edio_data_out4 4 O pr1_pru1_pru_r30_10 5 O pr1_pru1_pru_r31_10 6 I gpio2_24 7 I/O lcd_vsync 0 O gpmc_a8 1 O pr1_edio_data_in2 3 I pr1_edio_data_out2 4 O pr1_pru1_pru_r30_8 5 O pr1_pru1_pru_r31_8 6 I gpio2_22 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z Z 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z L 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z L 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z L 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 33 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] NA NA PRODUCT PREVIEW NA NA NA 34 B13 B12 C12 A14 A13 PIN NAME [2] MCASP0_FSX MCASP0_ACLKR MCASP0_AHCLKR MCASP0_AHCLKX MCASP0_ACLKX SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] mcasp0_fsx 0 I/O ehrpwm0B 1 O spi1_d0 3 I/O mmc1_sdcd 4 I pr1_pru0_pru_r30_1 5 O pr1_pru0_pru_r31_1 6 I gpio3_15 7 I/O mcasp0_aclkr 0 I/O eQEP0A_in 1 I mcasp0_axr2 2 I/O mcasp1_aclkx 3 I/O mmc0_sdwp 4 I pr1_pru0_pru_r30_4 5 O pr1_pru0_pru_r31_4 6 I gpio3_18 7 I/O mcasp0_ahclkr 0 I/O ehrpwm0_synci 1 I mcasp0_axr2 2 I/O spi1_cs0 3 I/O eCAP2_in_PWM2_out 4 I/O pr1_pru0_pru_r30_3 5 O pr1_pru0_pru_r31_3 6 I gpio3_17 7 I/O mcasp0_ahclkx 0 I/O eQEP0_strobe 1 I/O mcasp0_axr3 2 I/O mcasp1_axr1 3 I/O EMU4 4 I/O pr1_pru0_pru_r30_7 5 O pr1_pru0_pru_r31_7 6 I gpio3_21 7 I/O mcasp0_aclkx 0 I/O ehrpwm0A 1 O spi1_sclk 3 I/O mmc0_sdcd 4 I pr1_pru0_pru_r30_0 5 O pr1_pru0_pru_r31_0 6 I gpio3_14 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) NA NA NA R19 P17 C13 D12 D13 M18 M17 PIN NAME [2] MCASP0_FSR MCASP0_AXR0 MCASP0_AXR1 MDC MDIO SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] mcasp0_fsr 0 I/O eQEP0B_in 1 I mcasp0_axr3 2 I/O mcasp1_fsx 3 I/O EMU2 4 I/O pr1_pru0_pru_r30_5 5 O pr1_pru0_pru_r31_5 6 I gpio3_19 7 I/O mcasp0_axr0 0 I/O ehrpwm0_tripzone_input 1 I spi1_d1 3 I/O mmc2_sdcd 4 I pr1_pru0_pru_r30_2 5 O pr1_pru0_pru_r31_2 6 I gpio3_16 7 I/O mcasp0_axr1 0 I/O eQEP0_index 1 I/O mcasp1_axr0 3 I/O EMU3 4 I/O pr1_pru0_pru_r30_6 5 O pr1_pru0_pru_r31_6 6 I gpio3_20 7 I/O mdio_clk 0 O timer5 1 I/O uart5_txd 2 O uart3_rtsn 3 O mmc0_sdwp 4 I mmc1_clk 5 I/O mmc2_clk 6 I/O gpio0_1 7 I/O mdio_data 0 I/O timer6 1 I/O uart5_rxd 2 O uart3_ctsn 3 I mmc0_sdcd 4 I mmc1_cmd 5 I/O mmc2_cmd 6 I/O gpio0_0 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS L L 7 NA / VDDSHV6 Yes 6 PU/PD LVCMOS H H 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS H H 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 35 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] L19 K17 PRODUCT PREVIEW K19 M19 36 J17 J16 J15 L18 PIN NAME [2] MII1_RX_DV MII1_TX_EN MII1_RX_ER MII1_RX_CLK SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gmii1_rxdv 0 I lcd_memory_clk 1 O rgmii1_rctl 2 I uart5_txd 3 O mcasp1_aclkx 4 I/O mmc2_dat0 5 I/O mcasp0_aclkr 6 I/O gpio3_4 7 I/O gmii1_txen 0 O rmii1_txen 1 O rgmii1_tctl 2 O timer4 3 I/O mcasp1_axr0 4 I/O eQEP0_index 5 I/O mmc2_cmd 6 I/O gpio3_3 7 I/O gmii1_rxerr 0 I rmii1_rxerr 1 I spi1_d1 2 I/O I2C1_SCL 3 I/OD mcasp1_fsx 4 I/O uart5_rtsn 5 O uart2_txd 6 O gpio3_2 7 I/O gmii1_rxclk 0 I uart2_txd 1 O rgmii1_rclk 2 I mmc0_dat6 3 I/O mmc1_dat1 4 I/O uart1_dsrn 5 I mcasp0_fsx 6 I/O gpio3_10 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) N19 J19 J18 P18 K18 H16 H17 M16 PIN NAME [2] MII1_TX_CLK MII1_COL MII1_CRS MII1_RXD0 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gmii1_txclk 0 I uart2_rxd 1 I rgmii1_tclk 2 O mmc0_dat7 3 I/O mmc1_dat0 4 I/O uart1_dcdn 5 I mcasp0_aclkx 6 I/O gpio3_9 7 I/O gmii1_col 0 I rmii2_refclk 1 I/O spi1_sclk 2 I/O uart5_rxd 3 I mcasp1_axr2 4 I/O mmc2_dat3 5 I/O mcasp0_axr2 6 I/O gpio3_0 7 I/O gmii1_crs 0 I rmii1_crs_dv 1 I spi1_d0 2 I/O I2C1_SDA 3 I/OD mcasp1_aclkx 4 I/O uart5_ctsn 5 I uart2_rxd 6 I gpio3_1 7 I/O gmii1_rxd0 0 I rmii1_rxd0 1 I rgmii1_rd0 2 I mcasp1_ahclkx 3 I/O mcasp1_ahclkr 4 I/O mcasp1_aclkr 5 I/O mcasp0_axr3 6 I/O gpio2_21 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 37 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] P19 N16 PRODUCT PREVIEW N17 L18 38 L15 L16 L17 K17 PIN NAME [2] MII1_RXD1 MII1_RXD2 MII1_RXD3 MII1_TXD0 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gmii1_rxd1 0 I rmii1_rxd1 1 I rgmii1_rd1 2 I mcasp1_axr3 3 I/O mcasp1_fsr 4 I/O eQEP0_strobe 5 I/O mmc2_clk 6 I/O gpio2_20 7 I/O gmii1_rxd2 0 I uart3_txd 1 O rgmii1_rd2 2 I mmc0_dat4 3 I/O mmc1_dat3 4 I/O uart1_rin 5 I mcasp0_axr1 6 I/O gpio2_19 7 I/O gmii1_rxd3 0 I uart3_rxd 1 I rgmii1_rd3 2 I mmc0_dat5 3 I/O mmc1_dat2 4 I/O uart1_dtrn 5 O mcasp0_axr0 6 I/O gpio2_18 7 I/O gmii1_txd0 0 O rmii1_txd0 1 O rgmii1_td0 2 O mcasp1_axr2 3 I/O mcasp1_aclkr 4 I/O eQEP0B_in 5 I mmc1_clk 6 I/O gpio0_28 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) M18 N18 M17 G17 K16 K15 J18 G18 PIN NAME [2] MII1_TXD1 MII1_TXD2 MII1_TXD3 MMC0_CMD SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] gmii1_txd1 0 O rmii1_txd1 1 O rgmii1_td1 2 O mcasp1_fsr 3 I/O mcasp1_axr1 4 I/O eQEP0A_in 5 I mmc1_cmd 6 I/O gpio0_21 7 I/O gmii1_txd2 0 O dcan0_rx 1 I rgmii1_td2 2 O uart4_txd 3 O mcasp1_axr0 4 I/O mmc2_dat2 5 I/O mcasp0_ahclkx 6 I/O gpio0_17 7 I/O gmii1_txd3 0 O dcan0_tx 1 O rgmii1_td3 2 O uart4_rxd 3 I mcasp1_fsx 4 I/O mmc2_dat1 5 I/O mcasp0_fsr 6 I/O gpio0_16 7 I/O mmc0_cmd 0 I/O gpmc_a25 1 O uart3_rtsn 2 O uart2_txd 3 O dcan1_rx 4 I pr1_pru0_pru_r30_13 5 O pr1_pru0_pru_r31_13 6 I gpio2_31 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS L L 7 VDDSHV5 / VDDSHV5 Yes 6 PU/PD LVCMOS H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 39 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] G19 G18 PRODUCT PREVIEW H17 H18 40 G17 G16 G15 F18 PIN NAME [2] MMC0_CLK MMC0_DAT0 MMC0_DAT1 MMC0_DAT2 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] mmc0_clk 0 I/O gpmc_a24 1 O uart3_ctsn 2 I uart2_rxd 3 I dcan1_tx 4 O pr1_pru0_pru_r30_12 5 O pr1_pru0_pru_r31_12 6 I gpio2_30 7 I/O mmc0_dat0 0 I/O gpmc_a23 1 O uart5_rtsn 2 O uart3_txd 3 O uart1_rin 4 I pr1_pru0_pru_r30_11 5 O pr1_pru0_pru_r31_11 6 I gpio2_29 7 I/O mmc0_dat1 0 I/O gpmc_a22 1 O uart5_ctsn 2 I uart3_rxd 3 I uart1_dtrn 4 O pr1_pru0_pru_r30_10 5 O pr1_pru0_pru_r31_10 6 I gpio2_28 7 I/O mmc0_dat2 0 I/O gpmc_a21 1 O uart4_rtsn 2 O timer6 3 I/O uart1_dsrn 4 I pr1_pru0_pru_r30_9 5 O pr1_pru0_pru_r31_9 6 I gpio2_27 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) H19 F17 PIN NAME [2] MMC0_DAT3 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] mmc0_dat3 0 I/O gpmc_a20 1 O uart4_ctsn 2 I timer5 3 I/O uart1_dcdn 4 I pr1_pru0_pru_r30_8 5 O pr1_pru0_pru_r31_8 6 I gpio2_26 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] H H 7 VDDSHV4 / VDDSHV4 Yes 6 PU/PD LVCMOS C7 C6 PMIC_POWER_EN PMIC_POWER_EN 0 O H 1 0 VDDS_RTC / VDDS_RTC NA 6 NA LVCMOS E15 B15 PWRONRSTn porz 0 I Z Z 0 VDDSHV6 / VDDSHV6 Yes NA NA LVCMOS B6 A3 RESERVED testout 0 O NA NA NA VDDSHV6 / VDDSHV6 NA NA NA Analog K18 H18 RMII1_REF_CLK rmii1_refclk 0 I/O L L 7 6 PU/PD LVCMOS 1 I VDDSHV5 / VDDSHV5 Yes xdma_event_intr2 spi1_cs0 2 I/O uart5_txd 3 O mcasp1_axr3 4 I/O mmc0_pow 5 O mcasp1_ahclkx 6 I/O gpio0_29 7 I/O A7 B4 RTC_KALDO_ENn ENZ_KALDO_1P8V 0 I Z Z 0 VDDS_RTC / VDDS_RTC NA NA NA Analog B7 B5 RTC_PWRONRSTn RTC_porz 0 I Z Z 0 VDDS_RTC / VDDS_RTC Yes NA NA LVCMOS A6 A6 RTC_XTALIN OSC1_IN 0 I Z Z 0 VDDS_RTC / VDDS_RTC Yes NA NA (2) LVCMOS A5 A4 RTC_XTALOUT OSC1_OUT 0 O Z Z 0 VDDS_RTC / VDDS_RTC NA TBD NA LVCMOS A18 A17 SPI0_SCLK spi0_sclk 0 I/O Z H 7 6 PU/PD LVCMOS 1 I VDDSHV6 / VDDSHV6 Yes uart2_rxd I2C2_SDA 2 I/OD ehrpwm0A 3 O pr1_uart0_cts_n 4 I pr1_edio_sof 5 O EMU2 6 I/O gpio0_2 7 I/O (14) Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 41 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] A17 B16 PRODUCT PREVIEW B18 B17 A16 C15 B17 B16 PIN NAME [2] SPI0_CS0 SPI0_CS1 SPI0_D0 SPI0_D1 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] spi0_cs0 0 I/O mmc2_sdwp 1 I I2C1_SCL 2 I/OD ehrpwm0_synci 3 I pr1_uart0_txd 4 O pr1_edio_data_in1 5 I pr1_edio_data_out1 6 O gpio0_5 7 I/O spi0_cs1 0 I/O uart3_rxd 1 I eCAP1_in_PWM1_out 2 I/O mmc0_pow 3 O xdma_event_intr2 4 I mmc0_sdcd 5 I EMU4 6 I/O gpio0_6 7 I/O spi0_d0 0 I/O uart2_txd 1 O I2C2_SCL 2 I/OD ehrpwm0B 3 O pr1_uart0_rts_n 4 O pr1_edio_latch_in 5 I EMU3 6 I/O gpio0_3 7 I/O spi0_d1 0 I/O mmc1_sdwp 1 I I2C1_SDA 2 I/OD ehrpwm0_tripzone_input 3 I pr1_uart0_rxd 4 I pr1_edio_data_in0 5 I pr1_edio_data_out0 6 O gpio0_4 7 I/O BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z H 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 6 PU/PD LVCMOS B14 A12 TCK TCK 0 I H H 0 VDDSHV6 / VDDSHV6 Yes NA PU/PD LVCMOS B13 B11 TDI TDI 0 I H H 0 VDDSHV6 / VDDSHV6 Yes NA PU/PD LVCMOS A14 A11 TDO TDO 0 O H H 0 VDDSHV6 / VDDSHV6 NA 4 PU/PD LVCMOS C14 C11 TMS TMS 0 I H H 0 VDDSHV6 / VDDSHV6 Yes NA PU/PD LVCMOS 42 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) PIN NAME [2] SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] A13 B10 TRSTn nTRST 0 I L L 0 VDDSHV6 / VDDSHV6 Yes NA PU/PD LVCMOS F17 E16 UART0_TXD uart0_txd 0 O Z H 7 4 PU/PD LVCMOS 1 I/O VDDSHV6 / VDDSHV6 Yes spi1_cs1 dcan0_rx 2 I I2C2_SCL 3 I/OD eCAP1_in_PWM1_out 4 I/O pr1_pru1_pru_r30_15 5 O pr1_pru1_pru_r31_15 6 I gpio1_11 7 I/O uart0_ctsn 0 I Z H 7 4 PU/PD LVCMOS 1 I VDDSHV6 / VDDSHV6 Yes uart4_rxd dcan1_tx 2 O I2C1_SDA 3 I/OD spi1_d0 4 I/O timer7 5 I/O pr1_edc_sync0_out 6 O gpio1_8 7 I/O uart0_rxd 0 I Z H 7 4 PU/PD LVCMOS 1 I/O VDDSHV6 / VDDSHV6 Yes spi1_cs0 dcan0_tx 2 O I2C2_SDA 3 I/OD eCAP2_in_PWM2_out 4 I/O pr1_pru1_pru_r30_14 5 O pr1_pru1_pru_r31_14 6 I gpio1_10 7 I/O uart0_rtsn 0 O Z H 7 4 PU/PD LVCMOS 1 O VDDSHV6 / VDDSHV6 Yes uart4_txd dcan1_rx 2 I I2C1_SCL 3 I/OD spi1_d1 4 I/O spi1_cs0 5 I/O pr1_edc_sync1_out 6 O gpio1_9 7 I/O F19 E19 F18 E18 E15 E17 UART0_CTSn UART0_RXD UART0_RTSn Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] 43 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] C19 D18 PRODUCT PREVIEW D19 E17 T18 D15 D16 D17 D18 M15 PIN NAME [2] UART1_TXD UART1_RXD UART1_RTSn UART1_CTSn USB0_CE SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] uart1_txd 0 O mmc2_sdwp 1 I dcan1_rx 2 I I2C1_SCL 3 I/OD pr1_uart0_txd 5 O pr1_pru0_pru_r31_16 6 I gpio0_15 7 I/O uart1_rxd 0 I mmc1_sdwp 1 I dcan1_tx 2 O I2C1_SDA 3 I/OD pr1_uart0_rxd 5 I pr1_pru1_pru_r31_16 6 I gpio0_14 7 I/O uart1_rtsn 0 O timer5 1 I/O dcan0_rx 2 I I2C2_SCL 3 I/OD spi1_cs1 4 I/O pr1_uart0_rts_n 5 O pr1_edc_latch1_in 6 I gpio0_13 7 I/O uart1_ctsn 0 I timer6 1 I/O dcan0_tx 2 O I2C2_SDA 3 I/OD spi1_cs0 4 I/O pr1_uart0_cts_n 5 I pr1_edc_latch0_in 6 I gpio0_12 7 I/O USB0_CE 0 A BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z H 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z Z 0 VDDA*_USB0 / VDDA*_USB0 TBD TBD TBD Analog TBD TBD TBD Analog VDDA*_USB0 / VDDA*_USB0 TBD TBD TBD Analog VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS (16) T19 P15 USB0_VBUS USB0_VBUS 0 A Z Z 0 VDDA*_USB0 / VDDA*_USB0 (16) U18 N18 USB0_DM USB0_DM 0 A Z Z 0 G16 F16 USB0_DRVVBUS USB0_DRVVBUS 0 O L 0(PD) 0 gpio0_18 7 I/O 44 (5) Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] V19 P16 PIN NAME [2] USB0_ID SIGNAL NAME [3] USB0_ID MODE [4] 0 BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] A Z Z 0 VDDA*_USB0 / VDDA*_USB0 BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] TBD TBD TBD Analog VDDA*_USB0 / VDDA*_USB0 TBD TBD TBD Analog NA / VDDA*_USB1 TBD TBD TBD Analog TBD TBD TBD Analog TBD TBD TBD Analog TBD TBD TBD Analog NA / VDDSHV6 Yes 4 PU/PD LVCMOS NA / VDDA*_USB1 TBD TBD Analog (16) U19 N17 USB0_DP USB0_DP 0 A Z Z 0 NA P18 USB1_CE USB1_CE 0 A Z Z 0 (5) (17) NA P17 USB1_ID USB1_ID 0 A Z Z 0 NA / VDDA*_USB1 NA T18 USB1_VBUS USB1_VBUS 0 A Z Z 0 NA / VDDA*_USB1 PRODUCT PREVIEW (17) (17) NA R17 USB1_DP USB1_DP 0 A Z Z 0 NA F15 USB1_DRVVBUS USB1_DRVVBUS 0 O L 0(PD) 0 gpio3_13 7 I/O Z Z 0 NA R18 USB1_DM USB1_DM 0 A R17 N16 VDDA1P8V_USB0 VDDA1P8V_USB0 NA PWR NA R16 VDDA1P8V_USB1 VDDA1P8V_USB1 NA PWR R18 N15 VDDA3P3V_USB0 VDDA3P3V_USB0 NA PWR NA R15 VDDA3P3V_USB1 VDDA3P3V_USB1 NA PWR D7 D8 VDDA_ADC VDDA_ADC NA PWR D12, F16, E6, E14, F9, M16, T6, T14 K13, N6, P9, P14 VDDS VDDS NA PWR R8, R9, R11, R12, R13 P7, P8 VDDSHV1 VDDSHV1 NA PWR NA P10, P11 VDDSHV2 VDDSHV2 NA PWR NA P12, P13 VDDSHV3 VDDSHV3 NA PWR G15, H14, H15 H14, J14 VDDSHV4 VDDSHV4 NA PWR M14, M15, N15 K14, L14 VDDSHV5 VDDSHV5 NA PWR E11, E12, E10, E11, VDDSHV6 E13, F14, P6, E12, E13, R7 F14, G14, N5, P5, P6 VDDSHV6 NA PWR G5, H5, H6, K4, K5, M5, M6, N5 E5, F5, G5, VDDS_DDR H5, J5, K5, L5 VDDS_DDR NA PWR U10 R11 VDDS_OSC VDDS_OSC NA PWR T8 R10 VDDS_PLL_CORE_LCD VDDS_PLL_CORE_LCD NA PWR C5 E7 VDDS_PLL_DDR VDDS_PLL_DDR NA PWR (6) (6) NA / VDDA*_USB1 TBD Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 45 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] PIN NAME [2] SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] BUFFER STRENGTH (mA) [11] PULLUP /DOWN TYPE [12] I/O CELL [13] PRODUCT PREVIEW H16 H15 VDDS_PLL_MPU VDDS_PLL_MPU NA PWR C6 D7 VDDS_RTC VDDS_RTC NA PWR C10 E9 VDDS_SRAM_CORE_BG VDDS_SRAM_CORE_BG NA PWR C12 D10 VDDS_SRAM_MPU_BB VDDS_SRAM_MPU_BB NA PWR F9, F11, G9, G11, H7, H8, H12, H13, J7, J8, J12, J13, K15, K16, L7, L8, L12, L13, M7, M8, M12, M13, N9, N11, P9, P11 F6, F7, G6, VDD_CORE G7, G10, H11, J12, K6, K8, K12, L6, L7, L8, L9, M11, M13, N8, N9, N12, N13 VDD_CORE NA PWR NA F10, F11, F12, F13, G13, H13, J13 VDD_MPU VDD_MPU NA PWR NA A2 VDD_MPU_MON VDD_MPU_MON NA R5 M5 VPP VPP NA PWR B9 A9 VREFN VREFN 0 AP Z Z 0 VDDA_ADC / VDDA_ADC NA NA NA Analog A9 B9 VREFP VREFP 0 AP Z Z 0 VDDA_ADC / VDDA_ADC NA NA NA Analog A1, A19, D10, E7, E8, E9, E10, F6, F7, F8, F12, F13, G8, G12, H9, H10, H11, J5, J6, J9, J11, J14, J15, K8, K9, K11, K12, L5, L6, L9, L11, L14, L15, M9, M10, M11, N8, N12, P7, P8, P12, P13, P14, R10, T10, W1, W19 A1, A18, F8, VSS G8, G9, G11, G12, H6, H7, H8, H9, H10, H12, J6, J7, J8, J9, J10, J11, K7, K9, K10, K11, L10, L11, L12, L13, M6, M7, M8, M9, M10, M12, N7, N10, N11, V1, V18 VSS NA GND D8 E8 VSSA_ADC VSSA_ADC NA GND P16 M14, N14 VSSA_USB VSSA_USB NA GND V11 V11 VSS_OSC VSS_OSC NA A NA A5 VSS_RTC VSS_RTC NA GND A16 A10 WARMRSTn nRESETIN_OUT 0 I/OD 0 0 0 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS 46 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-7. Ball Characteristics (ZCE and ZCZ Packages) (continued) C15 B15 A15 D14 PIN NAME [2] XDMA_EVENT_INTR0 XDMA_EVENT_INTR1 SIGNAL NAME [3] MODE [4] BALL RESET TYPE BALL RESET RESET REL. ZCE POWER / HYS REL. STATE [5] STATE [6] MODE [8] ZCZ POWER [9] [10] [7] xdma_event_intr0 0 I timer4 2 I/O clkout1 3 O spi1_cs1 4 I/O pr1_pru1_pru_r31_16 5 I EMU2 6 I/O gpio0_19 7 I/O xdma_event_intr1 0 I tclkin 2 I clkout2 3 O timer7 4 I/O pr1_pru0_pru_r31_16 5 I EMU3 6 I/O gpio0_20 7 I/O PULLUP /DOWN TYPE [12] I/O CELL [13] (7) (4) VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z L 7 VDDSHV6 / VDDSHV6 Yes 4 PU/PD LVCMOS Z 0 VDDS_OSC / VDDS_OSC Yes NA PD (1) LVCMOS 0 VDDS_OSC / VDDS_OSC NA TBD NA LVCMOS Z (8) BUFFER STRENGTH (mA) [11] W11 V10 XTALIN OSC0_IN 0 I Z W12 U11 XTALOUT OSC0_OUT 0 O (15) PRODUCT PREVIEW ZCE BALL ZCZ BALL NUMBER [1] NUMBER [1] (1) A internal 15 kohm pull down is turned on when the oscillator is disabled. The oscillator is enabled by default after power is applied. (2) An external pull-down resistor should be connected to this terminal to minmize leakage current when not using the oscillator. (3) LCD_DATA[15:0] terminals are respectively SYSBOOT[15:0] inputs, latched on the rising edge of PWRONRSTn. (4) Reset Release Mode = 7 if sysboot[5] is low. Mode = 3 if sysboot[5] is high. (5) The internal USB PHY can be configured to multiplex the UART2_TX or UART2_RX signals to this terminal. For more details refer to USB GPIO Details section of the TRM. (6) The internal USB PHY can be configured to multiplex the UART3_TX or UART3_RX signals to this terminal. For more details refer to USB GPIO Details section of the TRM. (7) This terminal has an internal pull-down that remains on after reset is released if sysboot[5] is low on the rising edge or PWRONRSTn. This terminal will initially be driven low after reset is released if sysboot[5] is high on the rising edge or PWRONRSTn, then it begins to toggle at the same frequency of the XTALIN terminal. (8) This terminal has an internal pull-down turned on while reset is asserted. (9) This terminal is a analog input used to set the switching threshold of the DDR input buffers to (VDDS_DDR / 2). (10) This terminal is a analog passive signal that connects to an external 49.9 ohm 1%, 20mW reference resistor which is used to calibrate the DDR input/output buffers. (11) This terminal is analog input that may also be configured as an open-drain output. (12) This terminal is analog input that may also be configured as an open-source or open-drain output. (13) This terminal is analog input that may also be configured as an open-source output. (14) This terminal is high-Z when the oscillator is diasabled. This terminal is driven high if RTC_XTALIN is less than VIL, driven low if RTC_XTALIN is greater than VIH, and driven to a unknown value if RTC_XTALIN is between VIL and VIH when the oscillator is enabled. The oscillator is disabled by default after power is applied. (15) This terminal is high-Z when the oscillator is diasabled. This terminal is driven high if XTALIN is less than VIL, driven low if XTALIN is greater than VIH, and driven to a unknown value if XTALIN is between VIL and VIH when the oscillator is enabled. The oscillator is enabled by default after power is applied. (16) This terminal requires two power supplies, VDDA3P3v_USB0 and VDDA1P8v_USB0. The "*" character in the power supply name is a wild card that represents "3P3v" and "1P8v". Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 47 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com (17) This terminal requires two power supplies, VDDA3P3v_USB1 and VDDA1P8v_USB1. The "*" character in the power supply name is a wild card that represents "3P3v" and "1P8v". PRODUCT PREVIEW 48 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3 Signal Description The AM335x device contains many peripheral interfaces. In order to reduce package size and cost while maintaining maximum functionality, many of the AM335x terminals can multiplex up to eight signal functions. Although there are many combinations of pin multiplexing that are possible, only a certain number of sets, called IO sets, are valid due to timing limitations. These valid IO sets were carefully chosen to provide many possible application scenarios for the user. PRODUCT PREVIEW Texas Instruments has developed a Windows application called Pin Mux Utility that helps a system designer select the appropriate pin-multiplexing configuration for their AM335x-based product design. This tool provides a way to select valid IO sets of specific peripheral interfaces to ensure that the pin-multiplexing configuration selected for a design only uses valid IO sets supported by the AM335x device. Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 49 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com (1) SIGNAL NAME: The signal name (2) DESCRIPTION: Description of the signal (3) TYPE: Ball type for this specific function: – I = Input – O = Output – I/O = Input/Output – D = Open drain – DS = Differential – A = Analog (4) BALL: Package ball location Table 2-8. ADC Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW AIN0 Analog Input/Output A B8 B6 AIN1 Analog Input/Output A A11 C7 AIN2 Analog Input/Output A A8 B7 AIN3 Analog Input/Output A B11 A7 AIN4 Analog Input/Output A C8 C8 AIN5 Analog Input/Output A B12 B8 AIN6 Analog Input/Output A A10 A8 AIN7 Analog Input/Output A A12 C9 VREFN Analog Reference Input Negative Terminal AP B9 A9 VREFP Analog Reference Input Positive Terminal AP A9 B9 Table 2-9. Debug Subsystem Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] EMU0 MISC EMULATION PIN I/O A15 C14 EMU1 MISC EMULATION PIN I/O D14 B14 EMU2 MISC EMULATION PIN I/O A18, C15 A15, A17, C13 EMU3 MISC EMULATION PIN I/O B15, B18 B17, D13, D14 EMU4 MISC EMULATION PIN I/O B16, U17 A14, C15, T13 nTRST JTAG TEST RESET (ACTIVE LOW) I A13 B10 TCK JTAG TEST CLOCK I B14 A12 TDI JTAG TEST DATA INPUT I B13 B11 TDO JTAG TEST DATA OUTPUT O A14 A11 TMS JTAG TEST MODE SELECT I C14 C11 Table 2-10. ECAT Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_edc_latch0_in Data In I E17 D18 pr1_edc_latch1_in Data In I D19 D17 pr1_edc_sync0_out Data Out O F19 E18 pr1_edc_sync1_out Data Out O F18 E17 pr1_edio_data_in0 Data In I B17 B16 pr1_edio_data_in1 Data In I A17 A16 pr1_edio_data_in2 Data In I U7 U5 pr1_edio_data_in3 Data In I T7 R5 pr1_edio_data_in4 Data In I W5 V5 pr1_edio_data_in5 Data In I W7 R6 50 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-10. ECAT Signals Description (continued) SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_edio_data_in6 Data In I V14, V3 T3, U9 pr1_edio_data_in7 Data In I U15, U3 T4, V9 pr1_edio_data_out0 Data Out O B17 B16 pr1_edio_data_out1 Data Out O A17 A16 pr1_edio_data_out2 Data Out O U7 U5 pr1_edio_data_out3 Data Out O T7 R5 pr1_edio_data_out4 Data Out O W5 V5 pr1_edio_data_out5 Data Out O W7 R6 pr1_edio_data_out6 Data Out O V14, V3 T3, U9 pr1_edio_data_out7 Data Out O U15, U3 T4, V9 pr1_edio_latch_in Latch In I B18 B17 pr1_edio_sof Start of Frame O A18 A17 Table 2-11. LCD Controller Signals Description DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] lcd_ac_bias_en LCD AC bias enable chip select O W7 R6 lcd_data0 LCD data bus I/O U1 R1 lcd_data1 LCD data bus I/O U2 R2 lcd_data10 LCD data bus I/O U5 U3 lcd_data11 LCD data bus I/O V5 U4 lcd_data12 LCD data bus I/O V6 V2 lcd_data13 LCD data bus I/O U6 V3 lcd_data14 LCD data bus I/O W6 V4 lcd_data15 LCD data bus I/O V7 T5 lcd_data16 LCD data bus O V17 U13 lcd_data17 LCD data bus O W17 V13 lcd_data18 LCD data bus O T13 R12 lcd_data19 LCD data bus O U13 T12 lcd_data2 LCD data bus I/O V1 R3 lcd_data20 LCD data bus O U12 U12 lcd_data21 LCD data bus O T12 T11 lcd_data22 LCD data bus O W16 T10 lcd_data23 LCD data bus O V15 U10 lcd_data3 LCD data bus I/O V2 R4 lcd_data4 LCD data bus I/O W2 T1 lcd_data5 LCD data bus I/O W3 T2 lcd_data6 LCD data bus I/O V3 T3 lcd_data7 LCD data bus I/O U3 T4 lcd_data8 LCD data bus I/O V4 U1 lcd_data9 LCD data bus I/O W4 U2 lcd_hsync LCD Horizontal Sync O T7 R5 lcd_memory_clk LCD MCLK O L19, V16 J17, V12 lcd_pclk LCD pixel clock O W5 V5 lcd_vsync LCD Vertical Sync O U7 U5 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description PRODUCT PREVIEW SIGNAL NAME [1] 51 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.1 www.ti.com External Memory Interfaces Table 2-12. External Memory Interfaces/DDR Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW ddr_a0 DDR SDRAM ROW/COLUMN ADDRESS O F3 F3 ddr_a1 DDR SDRAM ROW/COLUMN ADDRESS O J2 H1 ddr_a10 DDR SDRAM ROW/COLUMN ADDRESS O E2 F4 ddr_a11 DDR SDRAM ROW/COLUMN ADDRESS O G4 F2 ddr_a12 DDR SDRAM ROW/COLUMN ADDRESS O F4 E3 ddr_a13 DDR SDRAM ROW/COLUMN ADDRESS O H1 H3 ddr_a14 DDR SDRAM ROW/COLUMN ADDRESS O H3 H4 ddr_a15 DDR SDRAM ROW/COLUMN ADDRESS O E3 D3 ddr_a2 DDR SDRAM ROW/COLUMN ADDRESS O D1 E4 ddr_a3 DDR SDRAM ROW/COLUMN ADDRESS O B3 C3 ddr_a4 DDR SDRAM ROW/COLUMN ADDRESS O E5 C2 ddr_a5 DDR SDRAM ROW/COLUMN ADDRESS O A2 B1 ddr_a6 DDR SDRAM ROW/COLUMN ADDRESS O B1 D5 ddr_a7 DDR SDRAM ROW/COLUMN ADDRESS O D2 E2 ddr_a8 DDR SDRAM ROW/COLUMN ADDRESS O C3 D4 ddr_a9 DDR SDRAM ROW/COLUMN ADDRESS O B2 C1 ddr_ba0 DDR SDRAM BANK ADDRESS O A3 C4 ddr_ba1 DDR SDRAM BANK ADDRESS O E1 E1 ddr_ba2 DDR SDRAM BANK ADDRESS O B4 B3 ddr_casn DDR SDRAM COLUMN ADDRESS STROBE. (ACTIVE LOW) O F1 F1 ddr_ck DDR SDRAM CLOCK (Differential+) O C2 D2 ddr_cke DDR SDRAM CLOCK ENABLE O G3 G3 ddr_csn0 DDR SDRAM CHIP SELECT O H2 H2 ddr_d0 DDR SDRAM DATA I/O N4 M3 ddr_d1 DDR SDRAM DATA I/O P4 M4 ddr_d10 DDR SDRAM DATA I/O M3 K2 ddr_d11 DDR SDRAM DATA I/O M4 K3 ddr_d12 DDR SDRAM DATA I/O M2 K4 ddr_d13 DDR SDRAM DATA I/O M1 L3 ddr_d14 DDR SDRAM DATA I/O N2 L4 ddr_d15 DDR SDRAM DATA I/O N1 M1 ddr_d2 DDR SDRAM DATA I/O P2 N1 ddr_d3 DDR SDRAM DATA I/O P1 N2 ddr_d4 DDR SDRAM DATA I/O P3 N3 ddr_d5 DDR SDRAM DATA I/O T1 N4 ddr_d6 DDR SDRAM DATA I/O T2 P3 ddr_d7 DDR SDRAM DATA I/O R3 P4 ddr_d8 DDR SDRAM DATA I/O K2 J1 ddr_d9 DDR SDRAM DATA I/O K1 K1 ddr_dqm0 DDR WRITE ENABLE / DATA MASK FOR DATA[7:0] O N3 M2 ddr_dqm1 DDR WRITE ENABLE / DATA MASK FOR DATA[15:8] O K3 J2 ddr_dqs0 DDR DATA STROBE FOR DATA[7:0] (Differential+) I/O R1 P1 52 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-12. External Memory Interfaces/DDR Signals Description (continued) SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] ddr_dqs1 DDR DATA STROBE FOR DATA[15:8] (Differential+) I/O L1 L1 ddr_dqsn0 DDR DATA STROBE FOR DATA[7:0] (Differential-) I/O R2 P2 ddr_dqsn1 DDR DATA STROBE FOR DATA[15:8] (Differential-) I/O L2 L2 ddr_nck DDR SDRAM CLOCK (Differential-) O C1 D1 ddr_odt ODT O G1 G1 ddr_rasn DDR SDRAM ROW ADDRESS STROBE (ACTIVE LOW) O F2 G4 ddr_resetn DDR3 resetn O G2 G2 ddr_vref Voltage Reference AP H4 J4 ddr_vtp VTP Compensation pin I J1 J3 ddr_wen DDR SDRAM WRITE ENABLE (ACTIVE LOW) O A4 B2 SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpmc_a0 GPMC Address O U1 R1, R13 gpmc_a1 GPMC Address O U2 R2, V14 gpmc_a10 GPMC Address O W5 T16, V5 gpmc_a11 GPMC Address O W7 R6, V17 gpmc_a12 GPMC Address O V4 U1 gpmc_a13 GPMC Address O W4 U2 gpmc_a14 GPMC Address O U5 U3 gpmc_a15 GPMC Address O V5 U4 gpmc_a16 GPMC Address O V6 R13, V2 gpmc_a17 GPMC Address O U6 V14, V3 gpmc_a18 GPMC Address O W6 U14, V4 gpmc_a19 GPMC Address O V7 T14, T5 gpmc_a2 GPMC Address O V1 R3, U14 gpmc_a20 GPMC Address O H19 F17, R14 gpmc_a21 GPMC Address O H18 F18, V15 gpmc_a22 GPMC Address O H17 G15, U15 gpmc_a23 GPMC Address O G18 G16, T15 gpmc_a24 GPMC Address O G19 G17, V16 gpmc_a25 GPMC Address O G17 G18, U16 gpmc_a26 GPMC Address O NA T16 gpmc_a27 GPMC Address O NA V17 gpmc_a3 GPMC Address O V2 R4, T14 gpmc_a4 GPMC Address O W2 R14, T1 gpmc_a5 GPMC Address O W3 T2, V15 gpmc_a6 GPMC Address O V3 T3, U15 gpmc_a7 GPMC Address O U3 T15, T4 gpmc_a8 GPMC Address O U7 U5, V16 gpmc_a9 GPMC Address O T7 R5, U16 gpmc_ad0 GPMC Address & Data I/O W10 U7 gpmc_ad1 GPMC Address & Data I/O V9 V7 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW Table 2-13. External Memory Interfaces/General Purpose Memory Controller Signals Description Terminal Description 53 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-13. External Memory Interfaces/General Purpose Memory Controller Signals Description (continued) SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW gpmc_ad10 GPMC Address & Data I/O T12 T11 gpmc_ad11 GPMC Address & Data I/O U12 U12 gpmc_ad12 GPMC Address & Data I/O U13 T12 gpmc_ad13 GPMC Address & Data I/O T13 R12 gpmc_ad14 GPMC Address & Data I/O W17 V13 gpmc_ad15 GPMC Address & Data I/O V17 U13 gpmc_ad2 GPMC Address & Data I/O V12 R8 gpmc_ad3 GPMC Address & Data I/O W13 T8 gpmc_ad4 GPMC Address & Data I/O V13 U8 gpmc_ad5 GPMC Address & Data I/O W14 V8 gpmc_ad6 GPMC Address & Data I/O U14 R9 gpmc_ad7 GPMC Address & Data I/O W15 T9 gpmc_ad8 GPMC Address & Data I/O V15 U10 gpmc_ad9 GPMC Address & Data I/O W16 T10 gpmc_advn_ale GPMC Address Valid / Address Latch Enable O V10 R7 gpmc_be0n_cle GPMC Byte Enable 0 / Command Latch Enable O V8 T6 gpmc_be1n GPMC Byte Enable 1 O U15, V18 U18, V9 gpmc_clk GPMC Clock I/O V14, V16 U9, V12 gpmc_csn0 GPMC Chip Select O W8 V6 gpmc_csn1 GPMC Chip Select O V14 U9 gpmc_csn2 GPMC Chip Select O U15 V9 gpmc_csn3 GPMC Chip Select O U17 T13 gpmc_csn4 GPMC Chip Select O R15 T17 gpmc_csn5 GPMC Chip Select O W18 U17 gpmc_csn6 GPMC Chip Select O V18 U18 gpmc_dir GPMC Data Direction O V18 U18 gpmc_oen_ren GPMC Output / Read Enable O W9 T7 gpmc_wait0 GPMC Wait 0 I R15 T17 gpmc_wait1 GPMC Wait 1 I V16 V12 gpmc_wen GPMC Write Enable O U8 U6 gpmc_wpn GPMC Write Protect O W18 U17 54 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.2 General Purpose IOs Table 2-14. General Purpose IOs/GPIO0 Signals Description DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpio0_0 GPIO I/O P17 M17 gpio0_1 GPIO I/O R19 M18 gpio0_10 GPIO I/O W6 V4 gpio0_11 GPIO I/O V7 T5 gpio0_12 GPIO I/O E17 D18 gpio0_13 GPIO I/O D19 D17 gpio0_14 GPIO I/O D18 D16 gpio0_15 GPIO I/O C19 D15 gpio0_16 GPIO I/O M17 J18 gpio0_17 GPIO I/O N18 K15 gpio0_18 GPIO I/O G16 F16 gpio0_19 GPIO I/O C15 A15 gpio0_2 GPIO I/O A18 A17 gpio0_20 GPIO I/O B15 D14 gpio0_21 GPIO I/O M18 K16 gpio0_22 GPIO I/O V15 U10 gpio0_23 GPIO I/O W16 T10 gpio0_26 GPIO I/O T12 T11 gpio0_27 GPIO I/O U12 U12 gpio0_28 GPIO I/O L18 K17 gpio0_29 GPIO I/O K18 H18 gpio0_3 GPIO I/O B18 B17 gpio0_30 GPIO I/O R15 T17 gpio0_31 GPIO I/O W18 U17 gpio0_4 GPIO I/O B17 B16 gpio0_5 GPIO I/O A17 A16 gpio0_6 GPIO I/O B16 C15 gpio0_7 GPIO I/O E18 C18 gpio0_8 GPIO I/O V6 V2 gpio0_9 GPIO I/O U6 V3 PRODUCT PREVIEW SIGNAL NAME [1] Table 2-15. General Purpose IOs/GPIO1 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpio1_0 GPIO I/O W10 U7 gpio1_1 GPIO I/O V9 V7 gpio1_10 GPIO I/O E19 E15 gpio1_11 GPIO I/O F17 E16 gpio1_12 GPIO I/O U13 T12 gpio1_13 GPIO I/O T13 R12 gpio1_14 GPIO I/O W17 V13 gpio1_15 GPIO I/O V17 U13 gpio1_16 GPIO I/O NA R13 gpio1_17 GPIO I/O NA V14 gpio1_18 GPIO I/O NA U14 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 55 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-15. General Purpose IOs/GPIO1 Signals Description (continued) SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW gpio1_19 GPIO I/O NA T14 gpio1_2 GPIO I/O V12 R8 gpio1_20 GPIO I/O NA R14 gpio1_21 GPIO I/O NA V15 gpio1_22 GPIO I/O NA U15 gpio1_23 GPIO I/O NA T15 gpio1_24 GPIO I/O NA V16 gpio1_25 GPIO I/O NA U16 gpio1_26 GPIO I/O NA T16 gpio1_27 GPIO I/O NA V17 gpio1_28 GPIO I/O V18 U18 gpio1_29 GPIO I/O W8 V6 gpio1_3 GPIO I/O W13 T8 gpio1_30 GPIO I/O V14 U9 gpio1_31 GPIO I/O U15 V9 gpio1_4 GPIO I/O V13 U8 gpio1_5 GPIO I/O W14 V8 gpio1_6 GPIO I/O U14 R9 gpio1_7 GPIO I/O W15 T9 gpio1_8 GPIO I/O F19 E18 gpio1_9 GPIO I/O F18 E17 Table 2-16. General Purpose IOs/GPIO2 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpio2_0 GPIO I/O U17 T13 gpio2_1 GPIO I/O V16 V12 gpio2_10 GPIO I/O W2 T1 gpio2_11 GPIO I/O W3 T2 gpio2_12 GPIO I/O V3 T3 gpio2_13 GPIO I/O U3 T4 gpio2_14 GPIO I/O V4 U1 gpio2_15 GPIO I/O W4 U2 gpio2_16 GPIO I/O U5 U3 gpio2_17 GPIO I/O V5 U4 gpio2_18 GPIO I/O N17 L17 gpio2_19 GPIO I/O N16 L16 gpio2_2 GPIO I/O V10 R7 gpio2_20 GPIO I/O P19 L15 gpio2_21 GPIO I/O P18 M16 gpio2_22 GPIO I/O U7 U5 gpio2_23 GPIO I/O T7 R5 gpio2_24 GPIO I/O W5 V5 gpio2_25 GPIO I/O W7 R6 gpio2_26 GPIO I/O H19 F17 gpio2_27 GPIO I/O H18 F18 gpio2_28 GPIO I/O H17 G15 56 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-16. General Purpose IOs/GPIO2 Signals Description (continued) SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpio2_29 GPIO I/O G18 G16 gpio2_3 GPIO I/O W9 T7 gpio2_30 GPIO I/O G19 G17 gpio2_31 GPIO I/O G17 G18 gpio2_4 GPIO I/O U8 U6 gpio2_5 GPIO I/O V8 T6 gpio2_6 GPIO I/O U1 R1 gpio2_7 GPIO I/O U2 R2 gpio2_8 GPIO I/O V1 R3 gpio2_9 GPIO I/O V2 R4 Table 2-17. General Purpose IOs/GPIO3 Signals Description DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] gpio3_0 GPIO I/O J19 H16 gpio3_1 GPIO I/O J18 H17 gpio3_10 GPIO I/O M19 L18 gpio3_13 GPIO I/O NA F15 gpio3_14 GPIO I/O NA A13 gpio3_15 GPIO I/O NA B13 gpio3_16 GPIO I/O NA D12 gpio3_17 GPIO I/O NA C12 gpio3_18 GPIO I/O NA B12 gpio3_19 GPIO I/O NA C13 gpio3_2 GPIO I/O K19 J15 gpio3_20 GPIO I/O NA D13 gpio3_21 GPIO I/O NA A14 gpio3_3 GPIO I/O K17 J16 gpio3_4 GPIO I/O L19 J17 gpio3_5 GPIO I/O C18 C17 gpio3_6 GPIO I/O B19 C16 gpio3_7 GPIO I/O A15 C14 gpio3_8 GPIO I/O D14 B14 gpio3_9 GPIO I/O N19 K18 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description PRODUCT PREVIEW SIGNAL NAME [1] 57 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.3 www.ti.com Miscellaneous Table 2-18. Miscellaneous/Miscellaneous Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW clkout1 Clock out1 O C15 A15 clkout2 Clock out2 O B15 D14 ENZ_KALDO_1P8V Active low output enable for CAP_VDD_RTC I A7 B4 EXT_WAKEUP EXT_WAKEUP I B5 C5 nNMI External Interrupt to ARM Cortext A8 core I C17 B18 nRESETIN_OUT Chip Reset I/OD A16 A10 OSC0_IN HF OSCILLATOR RECEIVER I W11 V10 OSC0_OUT HF OSCILLATOR DRIVER O W12 U11 PMIC_POWER_EN PMIC_POWER_EN O C7 C6 porz Power on Reset I E15 B15 tclkin Timer Clock In I B15 D14 xdma_event_intr0 External DMA Event or Interrupt 0 I C15 A15 xdma_event_intr1 External DMA Event or Interrupt 1 I B15 D14 xdma_event_intr2 External DMA Event or Interrupt 2 I B16, E18, K18 C15, C18, H18 58 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.3.1 eCAP Table 2-19. eCAP/eCAP0 Signals Description SIGNAL NAME [1] eCAP0_in_PWM0_out DESCRIPTION [2] enhanced capture 0 input or Auxiliary PWM0 out TYPE [3] I/O ZCE BALL [4] E18 ZCZ BALL [4] C18 Table 2-20. eCAP/eCAP1 Signals Description SIGNAL NAME [1] eCAP1_in_PWM1_out DESCRIPTION [2] enhanced capture 1 input or Auxiliary PWM1 out TYPE [3] I/O ZCE BALL [4] B16, B19, F17 ZCZ BALL [4] C15, C16, E16 Table 2-21. eCAP/eCAP2 Signals Description SIGNAL NAME [1] enhanced capture 2 input or Auxiliary PWM2 out TYPE [3] I/O ZCE BALL [4] C18, E19 ZCZ BALL [4] C12, C17, E15 PRODUCT PREVIEW eCAP2_in_PWM2_out DESCRIPTION [2] Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 59 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.3.2 www.ti.com eHRPWM Table 2-22. eHRPWM/eHRPWM0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] ehrpwm0A eHRPWM0 A output. O A18 A13, A17 ehrpwm0B eHRPWM0 B output. O B18 B13, B17 ehrpwm0_synci Sync input to eHRPWM0 module from an external pin I A17 A16, C12 ehrpwm0_synco Sync Output from eHRPWM0 module to an external pin O U12, V2, W4 R4, U12, U2, V14 ehrpwm0_tripzone_input eHRPWM0 trip zone input I B17 B16, D12 Table 2-23. eHRPWM/eHRPWM1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] ehrpwm1A eHRPWM1 A output. O U5 U14, U3 ehrpwm1B eHRPWM1 B output. O V5 T14, U4 ehrpwm1_tripzone_input eHRPWM1 trip zone input I V4 R13, U1 PRODUCT PREVIEW Table 2-24. eHRPWM/eHRPWM2 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] ehrpwm2A eHRPWM2 A output. O U1, V15 R1, U10 ehrpwm2B eHRPWM2 B output. O U2, W16 R2, T10 ehrpwm2_tripzone_input eHRPWM2 trip zone input I T12, V1 R3, T11 60 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.3.3 eQEP Table 2-25. eQEP/eQEP0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] eQEP0A_in eQEP0A quadrature input I M18 B12, K16 eQEP0B_in eQEP0B quadrature input I L18 C13, K17 eQEP0_index eQEP0 index. I/O K17 D13, J16 eQEP0_strobe eQEP0 strobe. I/O P19 A14, L15 Table 2-26. eQEP/eQEP1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] eQEP1A_in eQEP1A quadrature input I V6 R14, V2 eQEP1B_in eQEP1B quadrature input I U6 V15, V3 eQEP1_index eQEP1 index. I/O W6 U15, V4 eQEP1_strobe eQEP1 strobe. I/O V7 T15, T5 SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] eQEP2A_in eQEP2A quadrature input I U13, W2 T1, T12 eQEP2B_in eQEP2B quadrature input I T13, W3 R12, T2 eQEP2_index eQEP2 index. I/O V3, W17 T3, V13 eQEP2_strobe eQEP2 strobe. I/O U3, V17 T4, U13 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 PRODUCT PREVIEW Table 2-27. eQEP/eQEP2 Signals Description Terminal Description 61 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.3.4 www.ti.com Timer Table 2-28. Timer/Timer4 Signals Description SIGNAL NAME [1] timer4 DESCRIPTION [2] Timer trigger event / PWM out TYPE [3] I/O ZCE BALL [4] C15, C18, K17, V10 ZCZ BALL [4] A15, C17, J16, R7 Table 2-29. Timer/Timer5 Signals Description SIGNAL NAME [1] timer5 DESCRIPTION [2] Timer trigger event / PWM out TYPE [3] I/O ZCE BALL [4] D19, H19, R19, V8 ZCZ BALL [4] D17, F17, M18, T6 Table 2-30. Timer/Timer6 Signals Description SIGNAL NAME [1] timer6 DESCRIPTION [2] Timer trigger event / PWM out TYPE [3] I/O ZCE BALL [4] E17, H18, P17, U8 ZCZ BALL [4] D18, F18, M17, U6 PRODUCT PREVIEW Table 2-31. Timer/Timer7 Signals Description SIGNAL NAME [1] timer7 62 DESCRIPTION [2] Timer trigger event / PWM out Terminal Description TYPE [3] I/O ZCE BALL [4] B15, B19, F19, W9 ZCZ BALL [4] C16, D14, E18, T7 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.4 PRU Subsystem Table 2-32. PRU Subsystem/MII0 Signals Description TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_mii0_col MII Collision Detect I W16 T10 pr1_mii0_crs MII Carrier Sense I U17, W5 T13, V5 pr1_mii0_rxd0 MII Receive Data bit 0 I V5 U4 pr1_mii0_rxd1 MII Receive Data bit 1 I U5 U3 pr1_mii0_rxd2 MII Receive Data bit 2 I W4 U2 pr1_mii0_rxd3 MII Receive Data bit 3 I V4 U1 pr1_mii0_rxdv MII Receive Data Valid I V7 T5 pr1_mii0_rxer MII Receive Data Error I U6 V3 pr1_mii0_rxlink MII Receive Link I V6 V2 pr1_mii0_txd0 MII Transmit Data bit 0 O W17, W3 T2, V13 pr1_mii0_txd1 MII Transmit Data bit 1 O T13, W2 R12, T1 pr1_mii0_txd2 MII Transmit Data bit 2 O U13, V2 R4, T12 pr1_mii0_txd3 MII Transmit Data bit 3 O U12, V1 R3, U12 pr1_mii0_txen MII Transmit Enable O T12, U2 R2, T11 pr1_mii_mr0_clk MII Receive Clock I W6 V4 pr1_mii_mt0_clk MII Transmit Clock I U1, V15 R1, U10 PRODUCT PREVIEW SIGNAL NAME [1] Table 2-33. PRU Subsystem/MII1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_mii1_col MII Collision Detect I R15 T17 pr1_mii1_crs MII Carrier Sense I V16, W7 R6, V12 pr1_mii1_rxd0 MII Receive Data bit 0 I NA V16 pr1_mii1_rxd1 MII Receive Data bit 1 I NA T15 pr1_mii1_rxd2 MII Receive Data bit 2 I NA U15 pr1_mii1_rxd3 MII Receive Data bit 3 I NA V15 pr1_mii1_rxdv MII Receive Data Valid I NA T16 pr1_mii1_rxer MII Receive Data Error I NA V17 pr1_mii1_rxlink MII Receive Link I V18 U18 pr1_mii1_txd0 MII Transmit Data bit 0 O NA R14 pr1_mii1_txd1 MII Transmit Data bit 1 O NA T14 pr1_mii1_txd2 MII Transmit Data bit 2 O NA U14 pr1_mii1_txd3 MII Transmit Data bit 3 O NA V14 pr1_mii1_txen MII Transmit Enable O W18 U17 pr1_mii_mr1_clk MII Receive Clock I NA U16 pr1_mii_mt1_clk MII Transmit Clock I NA R13 Table 2-34. PRU Subsystem/UART0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_uart0_cts_n UART Clear to Send I A18, E17 A17, D18 pr1_uart0_rts_n UART Request to Send O B18, D19 B17, D17 pr1_uart0_rxd UART Receive Data I B17, D18 B16, D16 pr1_uart0_txd UART Transmit Data O A17, C19 A16, D15 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 63 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.4.1 www.ti.com PRU0 Table 2-35. PRU0/General Purpose Inputs Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW pr1_pru0_pru_r31_0 PRU0 Data In I NA A13 pr1_pru0_pru_r31_1 PRU0 Data In I NA B13 pr1_pru0_pru_r31_10 PRU0 Data In I H17 G15 pr1_pru0_pru_r31_11 PRU0 Data In I G18 G16 pr1_pru0_pru_r31_12 PRU0 Data In I G19 G17 pr1_pru0_pru_r31_13 PRU0 Data In I G17 G18 pr1_pru0_pru_r31_14 PRU0 Data In I W17 V13 pr1_pru0_pru_r31_15 PRU0 Data In I V17 U13 pr1_pru0_pru_r31_16 PRU0 Data In Capture Enable I B15, C19 D14, D15 pr1_pru0_pru_r31_2 PRU0 Data In I NA D12 pr1_pru0_pru_r31_3 PRU0 Data In I NA C12 pr1_pru0_pru_r31_4 PRU0 Data In I NA B12 pr1_pru0_pru_r31_5 PRU0 Data In I NA C13 pr1_pru0_pru_r31_6 PRU0 Data In I NA D13 pr1_pru0_pru_r31_7 PRU0 Data In I NA A14 pr1_pru0_pru_r31_8 PRU0 Data In I H19 F17 pr1_pru0_pru_r31_9 PRU0 Data In I H18 F18 Table 2-36. PRU0/General Purpose Outputs Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] pr1_pru0_pru_r30_0 PRU0 Data Out O NA A13 pr1_pru0_pru_r30_1 PRU0 Data Out O NA B13 pr1_pru0_pru_r30_10 PRU0 Data Out O H17 G15 pr1_pru0_pru_r30_11 PRU0 Data Out O G18 G16 pr1_pru0_pru_r30_12 PRU0 Data Out O G19 G17 pr1_pru0_pru_r30_13 PRU0 Data Out O G17 G18 pr1_pru0_pru_r30_14 PRU0 Data Out O U13 T12 pr1_pru0_pru_r30_15 PRU0 Data Out O T13 R12 pr1_pru0_pru_r30_2 PRU0 Data Out O NA D12 pr1_pru0_pru_r30_3 PRU0 Data Out O NA C12 pr1_pru0_pru_r30_4 PRU0 Data Out O NA B12 pr1_pru0_pru_r30_5 PRU0 Data Out O NA C13 pr1_pru0_pru_r30_6 PRU0 Data Out O NA D13 pr1_pru0_pru_r30_7 PRU0 Data Out O NA A14 pr1_pru0_pru_r30_8 PRU0 Data Out O H19 F17 pr1_pru0_pru_r30_9 PRU0 Data Out O H18 F18 64 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.4.2 PRU1 Table 2-37. PRU1/General Purpose Inputs Signals Description TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] pr1_pru1_pru_r31_0 PRU1 Data In I U1 R1 pr1_pru1_pru_r31_1 PRU1 Data In I U2 R2 pr1_pru1_pru_r31_10 PRU1 Data In I W5 V5 pr1_pru1_pru_r31_11 PRU1 Data In I W7 R6 pr1_pru1_pru_r31_12 PRU1 Data In I V14 U9 pr1_pru1_pru_r31_13 PRU1 Data In I U15 V9 pr1_pru1_pru_r31_14 PRU1 Data In I E19 E15 pr1_pru1_pru_r31_15 PRU1 Data In I F17 E16 pr1_pru1_pru_r31_16 PRU1 Data In Capture Enable I C15, D18 A15, D16 pr1_pru1_pru_r31_2 PRU1 Data In I V1 R3 pr1_pru1_pru_r31_3 PRU1 Data In I V2 R4 pr1_pru1_pru_r31_4 PRU1 Data In I W2 T1 pr1_pru1_pru_r31_5 PRU1 Data In I W3 T2 pr1_pru1_pru_r31_6 PRU1 Data In I V3 T3 pr1_pru1_pru_r31_7 PRU1 Data In I U3 T4 pr1_pru1_pru_r31_8 PRU1 Data In I U7 U5 pr1_pru1_pru_r31_9 PRU1 Data In I T7 R5 PRODUCT PREVIEW SIGNAL NAME [1] Table 2-38. PRU1/General Purpose Outputs Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] pr1_pru1_pru_r30_0 PRU1 Data Out O U1 R1 pr1_pru1_pru_r30_1 PRU1 Data Out O U2 R2 pr1_pru1_pru_r30_10 PRU1 Data Out O W5 V5 pr1_pru1_pru_r30_11 PRU1 Data Out O W7 R6 pr1_pru1_pru_r30_12 PRU1 Data Out O V14 U9 pr1_pru1_pru_r30_13 PRU1 Data Out O U15 V9 pr1_pru1_pru_r30_14 PRU1 Data Out O E19 E15 pr1_pru1_pru_r30_15 PRU1 Data Out O F17 E16 pr1_pru1_pru_r30_2 PRU1 Data Out O V1 R3 pr1_pru1_pru_r30_3 PRU1 Data Out O V2 R4 pr1_pru1_pru_r30_4 PRU1 Data Out O W2 T1 pr1_pru1_pru_r30_5 PRU1 Data Out O W3 T2 pr1_pru1_pru_r30_6 PRU1 Data Out O V3 T3 pr1_pru1_pru_r30_7 PRU1 Data Out O U3 T4 pr1_pru1_pru_r30_8 PRU1 Data Out O U7 U5 pr1_pru1_pru_r30_9 PRU1 Data Out O T7 R5 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 65 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.5 www.ti.com Removable Media Interfaces Table 2-39. Removable Media Interfaces/MMC0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] mmc0_clk MMC/SD/SDIO Clock I/O G19 G17 mmc0_cmd MMC/SD/SDIO Command I/O G17 G18 mmc0_dat0 MMC/SD/SDIO Data Bus I/O G18 G16 mmc0_dat1 MMC/SD/SDIO Data Bus I/O H17 G15 mmc0_dat2 MMC/SD/SDIO Data Bus I/O H18 F18 mmc0_dat3 MMC/SD/SDIO Data Bus I/O H19 F17 mmc0_dat4 MMC/SD/SDIO Data Bus I/O N16 L16 mmc0_dat5 MMC/SD/SDIO Data Bus I/O N17 L17 mmc0_dat6 MMC/SD/SDIO Data Bus I/O M19 L18 mmc0_dat7 MMC/SD/SDIO Data Bus I/O N19 K18 mmc0_pow MMC/SD Power Switch Control O B16, K18 C15, H18 mmc0_sdcd SD Card Detect I B16, P17 A13, C15, M17 mmc0_sdwp SD Write Protect I E18, R19 B12, C18, M18 PRODUCT PREVIEW Table 2-40. Removable Media Interfaces/MMC1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] mmc1_clk MMC/SD/SDIO Clock I/O L18, R19, V14 K17, M18, U9 mmc1_cmd MMC/SD/SDIO Command I/O M18, P17, U15 K16, M17, V9 mmc1_dat0 MMC/SD/SDIO Data Bus I/O N19, V15, W10 K18, U10, U7 mmc1_dat1 MMC/SD/SDIO Data Bus I/O M19, V9, W16 L18, T10, V7 mmc1_dat2 MMC/SD/SDIO Data Bus I/O N17, T12, V12 L17, R8, T11 mmc1_dat3 MMC/SD/SDIO Data Bus I/O N16, U12, W13 L16, T8, U12 mmc1_dat4 MMC/SD/SDIO Data Bus I/O U13, V13 T12, U8 mmc1_dat5 MMC/SD/SDIO Data Bus I/O T13, W14 R12, V8 mmc1_dat6 MMC/SD/SDIO Data Bus I/O U14, W17 R9, V13 mmc1_dat7 MMC/SD/SDIO Data Bus I/O V17, W15 T9, U13 mmc1_sdcd SD Card Detect I R15 B13, T17 mmc1_sdwp SD Write Protect I B17, D18 B16, D16 Table 2-41. Removable Media Interfaces/MMC2 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] mmc2_clk MMC/SD/SDIO Clock I/O P19, R19, V16 L15, M18, V12 mmc2_cmd MMC/SD/SDIO Command I/O K17, P17, U17 J16, M17, T13 mmc2_dat0 MMC/SD/SDIO Data Bus I/O L19, U13 J17, T12, V14 mmc2_dat1 MMC/SD/SDIO Data Bus I/O M17, T13 J18, R12, U14 mmc2_dat2 MMC/SD/SDIO Data Bus I/O N18, W17 K15, T14, V13 mmc2_dat3 MMC/SD/SDIO Data Bus I/O J19, V17, V18 H16, U13, U18 mmc2_dat4 MMC/SD/SDIO Data Bus I/O V15 U10, U15 mmc2_dat5 MMC/SD/SDIO Data Bus I/O W16 T10, T15 mmc2_dat6 MMC/SD/SDIO Data Bus I/O T12 T11, V16 mmc2_dat7 MMC/SD/SDIO Data Bus I/O U12 U12, U16 mmc2_sdcd SD Card Detect I W18 D12, U17 mmc2_sdwp SD Write Protect I A17, C19 A16, D15 66 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.6 2.3.6.1 Serial Communication Interfaces CAN Table 2-42. CAN/DCAN0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] dcan0_rx DCAN0 Receive Data I D19, F17, N18 D17, E16, K15 dcan0_tx DCAN0 Transmit Data O E17, E19, M17 D18, E15, J18 Table 2-43. CAN/DCAN1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] DCAN1 Receive Data I C19, F18, G17 D15, E17, G18 dcan1_tx DCAN1 Transmit Data O D18, F19, G19 D16, E18, G17 PRODUCT PREVIEW dcan1_rx Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 67 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.6.2 www.ti.com GEMAC_CPSW Table 2-44. GEMAC_CPSW/MDIO Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] mdio_clk MDIO Clk O R19 M18 mdio_data MDIO Data I/O P17 M17 Table 2-45. GEMAC_CPSW/MII1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW gmii1_col MII Colision I J19 H16 gmii1_crs MII Carrier Sense I J18 H17 gmii1_rxclk MII Receive Clock I M19 L18 gmii1_rxd0 MII Receive Data bit 0 I P18 M16 gmii1_rxd1 MII Receive Data bit 1 I P19 L15 gmii1_rxd2 MII Receive Data bit 2 I N16 L16 gmii1_rxd3 MII Receive Data bit 3 I N17 L17 gmii1_rxdv MII Receive Data Valid I L19 J17 gmii1_rxer MII Receive Data Error I K19 J15 gmii1_txclk MII Transmit Clock I N19 K18 gmii1_txd0 MII Transmit Data bit 0 O L18 K17 gmii1_txd1 MII Transmit Data bit 1 O M18 K16 gmii1_txd2 MII Transmit Data bit 2 O N18 K15 gmii1_txd3 MII Transmit Data bit 3 O M17 J18 gmii1_txen MII Transmit Enable O K17 J16 Table 2-46. GEMAC_CPSW/MII2 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] gmii2_col MII Colision I V18 U18 gmii2_crs MII Carrier Sense I R15 T17 gmii2_rxclk MII Receive Clock I NA T15 gmii2_rxd0 MII Receive Data bit 0 I NA V17 gmii2_rxd1 MII Receive Data bit 1 I NA T16 gmii2_rxd2 MII Receive Data bit 2 I NA U16 gmii2_rxd3 MII Receive Data bit 3 I NA V16 gmii2_rxdv MII Receive Data Valid I NA V14 gmii2_rxer MII Receive Data Error I W18 U17 gmii2_txclk MII Transmit Clock I NA U15 gmii2_txd0 MII Transmit Data bit 0 O NA V15 gmii2_txd1 MII Transmit Data bit 1 O NA R14 gmii2_txd2 MII Transmit Data bit 2 O NA T14 gmii2_txd3 MII Transmit Data bit 3 O NA U14 gmii2_txen MII Transmit Enable O NA R13 Table 2-47. GEMAC_CPSW/RGMII1 Signals Description SIGNAL NAME [1] rgmii1_rclk 68 Terminal Description TYPE [3] DESCRIPTION [2] RGMII Receive Clock I ZCE BALL [4] M19 ZCZ BALL [4] L18 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-47. GEMAC_CPSW/RGMII1 Signals Description (continued) SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] rgmii1_rctl RGMII Receive Control I L19 J17 rgmii1_rd0 RGMII Receive Data bit 0 I P18 M16 rgmii1_rd1 RGMII Receive Data bit 1 I P19 L15 rgmii1_rd2 RGMII Receive Data bit 2 I N16 L16 rgmii1_rd3 RGMII Receive Data bit 3 I N17 L17 rgmii1_tclk RGMII Transmit Clock O N19 K18 rgmii1_tctl RGMII Transmit Control O K17 J16 rgmii1_td0 RGMII Transmit Data bit 0 O L18 K17 rgmii1_td1 RGMII Transmit Data bit 1 O M18 K16 rgmii1_td2 RGMII Transmit Data bit 2 O N18 K15 rgmii1_td3 RGMII Transmit Data bit 3 O M17 J18 Table 2-48. GEMAC_CPSW/RGMII2 Signals Description TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] rgmii2_rclk RGMII Receive Clock I NA T15 rgmii2_rctl RGMII Receive Control I NA V14 rgmii2_rd0 RGMII Receive Data bit 0 I NA V17 rgmii2_rd1 RGMII Receive Data bit 1 I NA T16 rgmii2_rd2 RGMII Receive Data bit 2 I NA U16 rgmii2_rd3 RGMII Receive Data bit 3 I NA V16 rgmii2_tclk RGMII Transmit Clock O NA U15 rgmii2_tctl RGMII Transmit Control O NA R13 rgmii2_td0 RGMII Transmit Data bit 0 O NA V15 rgmii2_td1 RGMII Transmit Data bit 1 O NA R14 rgmii2_td2 RGMII Transmit Data bit 2 O NA T14 rgmii2_td3 RGMII Transmit Data bit 3 O NA U14 PRODUCT PREVIEW SIGNAL NAME [1] Table 2-49. GEMAC_CPSW/RMII1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] rmii1_crs_dv RMII Carrier Sense / Data Valid I J18 H17 rmii1_refclk RMII Reference Clock I/O K18 H18 rmii1_rxd0 RMII Receive Data bit 0 I P18 M16 rmii1_rxd1 RMII Receive Data bit 1 I P19 L15 rmii1_rxer RMII Receive Data Error I K19 J15 rmii1_txd0 RMII Transmit Data bit 0 O L18 K17 rmii1_txd1 RMII Transmit Data bit 1 O M18 K16 rmii1_txen RMII Transmit Enable O K17 J16 Table 2-50. GEMAC_CPSW/RMII2 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] rmii2_crs_dv RMII Carrier Sense / Data Valid I R15 T17 rmii2_refclk RMII Reference Clock I/O J19 H16 rmii2_rxd0 RMII Receive Data bit 0 I NA V17 rmii2_rxd1 RMII Receive Data bit 1 I NA T16 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 69 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-50. GEMAC_CPSW/RMII2 Signals Description (continued) SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] rmii2_rxer RMII Receive Data Error I W18 U17 rmii2_txd0 RMII Transmit Data bit 0 O NA V15 rmii2_txd1 RMII Transmit Data bit 1 O NA R14 rmii2_txen RMII Transmit Enable O NA R13 PRODUCT PREVIEW 70 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.6.3 I2C Table 2-51. I2C/I2C0 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] I2C0_SCL I2C0 Clock I/OD B19 C16 I2C0_SDA I2C0 Data I/OD C18 C17 Table 2-52. I2C/I2C1 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] I2C1_SCL I2C1 Clock I/OD A17, C19, F18, K19 A16, D15, E17, J15 I2C1_SDA I2C1 Data I/OD B17, D18, F19, J18 B16, D16, E18, H17 Table 2-53. I2C/I2C2 Signals Description DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] I2C2_SCL I2C2 Clock I/OD B18, D19, F17 B17, D17, E16 I2C2_SDA I2C2 Data I/OD A18, E17, E19 A17, D18, E15 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description PRODUCT PREVIEW SIGNAL NAME [1] 71 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.6.4 www.ti.com McASP Table 2-54. McASP/MCASP0 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW mcasp0_aclkr McASP0 Receive Bit Clock I/O L19, V18, V6 B12, J17, U18, V2 mcasp0_aclkx McASP0 Transmit Bit Clock I/O N19, V4 A13, K18, U1, V16 mcasp0_ahclkr McASP0 Receive Master Clock I/O V5 C12, U4 mcasp0_ahclkx McASP0 Transmit Master Clock I/O N18, V7 A14, K15, T5 mcasp0_axr0 McASP0 Serial Data (IN/OUT) I/O N17, U5 D12, L17, T16, U3 mcasp0_axr1 McASP0 Serial Data (IN/OUT) I/O N16, W6 D13, L16, V17, V4 mcasp0_axr2 McASP0 Serial Data (IN/OUT) I/O J19, V5, V6 B12, C12, H16, U4, V2 mcasp0_axr3 McASP0 Serial Data (IN/OUT) I/O P18, U6, V7 A14, C13, M16, T5, V3 mcasp0_fsr McASP0 Receive Frame Sync I/O M17, U6, V16 C13, J18, V12, V3 mcasp0_fsx McASP0 Transmit Frame Sync I/O M19, W4 B13, L18, U16, U2 Table 2-55. McASP/MCASP1 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] mcasp1_aclkr McASP1 Receive Bit Clock I/O L18, P18 K17, M16 mcasp1_aclkx McASP1 Transmit Bit Clock I/O J18, L19 B12, H17, J17 mcasp1_ahclkr McASP1 Receive Master Clock I/O P18 M16 mcasp1_ahclkx McASP1 Transmit Master Clock I/O K18, P18 H18, M16 mcasp1_axr0 McASP1 Serial Data (IN/OUT) I/O K17, N18 D13, J16, K15 mcasp1_axr1 McASP1 Serial Data (IN/OUT) I/O M18 A14, K16 mcasp1_axr2 McASP1 Serial Data (IN/OUT) I/O J19, L18 H16, K17 mcasp1_axr3 McASP1 Serial Data (IN/OUT) I/O K18, P19 H18, L15 mcasp1_fsr McASP1 Receive Frame Sync I/O M18, P19 K16, L15 mcasp1_fsx McASP1 Transmit Frame Sync I/O K19, M17 C13, J15, J18 72 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 2.3.6.5 SPI Table 2-56. SPI/SPI0 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] spi0_cs0 SPI Chip Select I/O A17 A16 spi0_cs1 SPI Chip Select I/O B16 C15 spi0_d0 SPI Data I/O B18 B17 spi0_d1 SPI Data I/O B17 B16 spi0_sclk SPI Clock I/O A18 A17 Table 2-57. SPI/SPI1 Signals Description DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] spi1_cs0 SPI Chip Select I/O E17, E19, F18, K18 C12, D18, E15, E17, H18 spi1_cs1 SPI Chip Select I/O C15, D19, E18, F17 A15, C18, D17, E16 spi1_d0 SPI Data I/O F19, J18 B13, E18, H17 spi1_d1 SPI Data I/O F18, K19 D12, E17, J15 spi1_sclk SPI Clock I/O E18, J19 A13, C18, H16 Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description PRODUCT PREVIEW SIGNAL NAME [1] 73 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.6.6 www.ti.com UART Table 2-58. UART/UART0 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] uart0_ctsn UART Clear to Send I F19 E18 uart0_rtsn UART Request to Send O F18 E17 uart0_rxd UART Receive Data I E19 E15 uart0_txd UART Transmit Data O F17 E16 Table 2-59. UART/UART1 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW uart1_ctsn UART Clear to Send I E17 D18 uart1_dcdn UART Data Carrier Detect I H19, N19 F17, K18 uart1_dsrn UART Data Set Ready I H18, M19 F18, L18 uart1_dtrn UART Data Terminal Ready O H17, N17 G15, L17 uart1_rin UART Ring Indicator I G18, N16 G16, L16 uart1_rtsn UART Request to Send O D19 D17 uart1_rxd UART Receive Data I D18 D16 uart1_txd UART Transmit Data O C19 D15 Table 2-60. UART/UART2 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] uart2_ctsn UART Clear to Send I C18, V4 C17, U1 uart2_rtsn UART Request to Send O B19, W4 C16, U2 uart2_rxd UART Receive Data I A18, G19, J18, N19 A17, G17, H17, K18 uart2_txd UART Transmit Data O B18, G17, K19, M19 B17, G18, J15, L18 Table 2-61. UART/UART3 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] uart3_ctsn UART Clear to Send I G19, P17, U5 G17, M17, U3 uart3_rtsn UART Request to Send O G17, R19, V5 G18, M18, U4 uart3_rxd UART Receive Data I B16, H17, N17 C15, G15, L17 uart3_txd UART Transmit Data O E18, G18, N16 C18, G16, L16 Table 2-62. UART/UART4 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] uart4_ctsn UART Clear to Send I H19, V6 F17, V2 uart4_rtsn UART Request to Send O H18, U6 F18, V3 uart4_rxd UART Receive Data I F19, M17, R15 E18, J18, T17 uart4_txd UART Transmit Data O F18, N18, W18 E17, K15, U17 74 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 2-63. UART/UART5 Signals Description SIGNAL NAME [1] TYPE [3] DESCRIPTION [2] ZCE BALL [4] ZCZ BALL [4] UART Clear to Send I H17, J18, W6 G15, H17, V4 uart5_rtsn UART Request to Send O G18, K19, V7 G16, J15, T5 uart5_rxd UART Receive Data O J19, P17, W4, W6 H16, M17, U2, V4 uart5_txd UART Transmit Data O K18, L19, R19, V4 H18, J17, M18, U1 PRODUCT PREVIEW uart5_ctsn Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Terminal Description 75 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 2.3.6.7 www.ti.com USB Table 2-64. USB/USB0 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] USB0_CE USB0 PHY Charger Enable A T18 M15 USB0_DM USB0 PHY DATA PLUS A U18 N18 USB0_DP USB0 PHY DATA MINUS A U19 N17 USB0_DRVVBUS USB0 CONTROLLER VBUS CONTROL OUTPUT O G16 F16 USB0_ID USB0 PHY IDENTIFICATION (Mini-A or Mini-B Plug) A V19 P16 USB0_VBUS USB0 BUS VOLTAGE A T19 P15 Table 2-65. USB/USB1 Signals Description SIGNAL NAME [1] DESCRIPTION [2] TYPE [3] ZCE BALL [4] ZCZ BALL [4] PRODUCT PREVIEW USB1_CE USB1 PHY Charger Enable A NA P18 USB1_DM USB1 PHY DATA MINUS A NA R18 USB1_DP USB1 PHY DATA PLUS A NA R17 USB1_DRVVBUS USB1 CONTROLLER VBUS CONTROL OUTPUT O NA F15 USB1_ID USB1 PHY IDENTIFICATION (Mini-A or Mini-B Plug) A NA P17 USB1_VBUS USB1 BUS VOLTAGE A NA T18 76 Terminal Description Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 3 Device Operating Conditions 3.1 Absolute Maximum Ratings Table 3-1. Absolute Maximum Ratings Over Junction Temperature Range (Unless Otherwise Noted)(1)(2) MAX Supply voltage for the MPU core domain PARAMETER -0.5 1.5 V VDD_CORE Supply voltage range for the core domain -0.5 1.5 V CAP_VDD_RTC(4) Supply voltage range for the RTC core domain -0.5 1.5 V VPP(5) Supply voltage range for the FUSE ROM domain -0.5 2.2 V VDDS_RTC Supply voltage range for the RTC domain -0.5 2.1 V VDDS_OSC Supply voltage range for the System oscillator -0.5 2.1 V VDDS_SRAM_CORE_BG Supply voltage range for the Core SRAM LDOs -0.5 2.1 V VDDS_SRAM_MPU_BB Supply voltage range for the MPU SRAM LDOs -0.5 2.1 V VDDS_PLL_DDR Supply voltage range for the DPLL DDR -0.5 2.1 V VDDS_PLL_CORE_LCD Supply voltage range for the DPLL Core and LCD -0.5 2.1 V VDDS_PLL_MPU Supply voltage range for the DPLL MPU -0.5 2.1 V VDDS_DDR Supply voltage range for the DDR IO domain -0.5 2.1 V VDDS Supply voltage range for all dual-voltage IO domains -0.5 2.1 V VDDA1P8V_USB0 Supply voltage range for USBPHY -0.5 2.1 V VDDA1P8V_USB1 (6) UNIT Supply voltage range for USBPHY -0.5 2.1 V VDDA_ADC Supply voltage range for ADC -0.5 2.1 V VDDSHV1 Supply voltage range for the dual-voltage IO domain -0.5 3.8 V VDDSHV2(6) Supply voltage range for the dual-voltage IO domain -0.5 3.8 V (6) VDDSHV3 Supply voltage range for the dual-voltage IO domain -0.5 3.8 V VDDSHV4 Supply voltage range for the dual-voltage IO domain -0.5 3.8 V VDDSHV5 Supply voltage range for the dual-voltage IO domain -0.5 3.8 V VDDSHV6 Supply voltage range for the dual-voltage IO domain -0.5 3.8 V VDDA3P3V_USB0 Supply voltage range for USBPHY -0.5 4 V VDDA3P3V_USB1(6) Supply voltage range for USBPHY -0.5 4 V USB0_VBUS Supply voltage range for USB VBUS comparator input -0.5 5.25 V USB1_VBUS(6) Supply voltage range for USB VBUS comparator input -0.5 5.25 V DDR_VREF Supply voltage range for the DDR SSTL/HSTL reference voltage -0.3 1.1 V -0.5 2.1 V -0.5 2.1 V Steady State Max. Voltage at all IO pins USB0_ID (6) USB1_ID -0.5V to NOM IO supply + 0.3 V Steady state maximum voltage range for the USB ID input Steady state maximum voltage range for the USB ID input Transient Overshoot / Undershoot specification at IO PAD 30% of supply for up to 30% of signal period Storage temperature range, Tstg(7) -55 ESD-HBM (Human Body Model) Electrostatic Discharge (ESD) Performance PRODUCT PREVIEW MIN VDD_MPU(3) (8) 155 °C ±2000 ESD-CDM (Charged-Device Model)(9) ±500 ESD-CDM (Charged-Device Model) Corner Terminals ±750 V (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to their associated VSS or VSSA_x. (3) Not available on the ZCE package. VDD_MPU is merged with VDD_CORE on the ZCE package. (4) This supply is sourced from an internal LDO when RTC_KALDO_ENn is low. If RTC_KALDO_ENn is high, this supply must be sourced Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 77 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com from an external power supply. (5) During functional operation, this pin is a no connect. (6) Not availabe on the ZCE package. (7) For tape and reel the storage temperature range is [-10°C; +50°C] with a maximum relative humidity of 70%. It is recommended returning to ambient room temperature before usage. (8) Based on JEDEC JESD22-A114E [Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM)]. (9) Based on JEDEC JESD22-C101C (Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components). PRODUCT PREVIEW 78 Device Operating Conditions Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-2 summarizes the power consumption at the AM335x power terminals. Table 3-2. Maximum Current Ratings at AM335x Power Terminals PARAMETER UNIT VDD_CORE(1) Maximum current rating for the core domain; OPP100 400 mA Maximum current rating for the core domain; OPP50 250 mA Maximum current rating for the MPU domain; Turbo 720 mA Maximum current rating for the MPU domain; OPP120 600 VDD_MPU(1) mA Maximum current rating for the MPU domain; OPP100 500 mA Maximum current rating for the MPU domain; OPP50 DESCRIPTION 300 mA CAP_VDD_RTC(2) Maximum current rating for RTC domain input/LDO output 2 mA VDDS_RTC Maximum current rating for the RTC domain 5 mA VDDS_DDR Maximum current rating for DDR IO domain 200 mA VDDS Maximum current rating for all dual-voltage IO domains 50 mA VDDS_SRAM_CORE_BG Maximum current rating for core SRAM LDOs 10 mA VDDS_SRAM_MPU_BB Maximum current rating for MPU SRAM LDOs 10 mA VDDS_PLL_DDR Maximum current rating for the DPLL DDR 10 mA VDDS_PLL_CORE_LCD Maximum current rating for the DPLL Core and LCD 20 mA VDDS_PLL_MPU Maximum current rating for the DPLL MPU 10 mA VDDS_OSC Maximum current rating for the system oscillator IOs 5 mA VDDA1P8V_USB0 Maximum current rating for USBPHY 1.8 V 40 mA VDDA1P8V_USB1(3) Maximum current rating for USBPHY 1.8 V 10 mA VDDA3P3V_USB0 Maximum current rating for USBPHY 3.3 V 40 mA VDDA3P3V_USB1(3) Maximum current rating for USBPHY 3.3 V 10 mA VDDA_ADC Maximum current rating for ADC 10 mA VDDSHV1(4) Maximum current rating for dual-voltage IO domain 50 mA (3) VDDSHV2 Maximum current rating for dual-voltage IO domain 50 mA VDDSHV3(3) Maximum current rating for dual-voltage IO domain 50 mA VDDSHV4 Maximum current rating for dual-voltage IO domain 50 mA VDDSHV5 Maximum current rating for dual-voltage IO domain 50 mA VDDSHV6 Maximum current rating for dual-voltage IO domain 100 mA PRODUCT PREVIEW MAX SUPPLY NAME (1) VDD_MPU is merged with VDD_CORE and is not available separately on the ZCE package. The maximum current rating for VDD_CORE on the ZCE package is the sum of VDD_CORE and VDD_MPU shown in this table. (2) This supply is sourced from an internal LDO when RTC_KALDO_ENn is low. If RTC_KALDO_ENn is high, this supply must be sourced from an external power supply. (3) Not available on the ZCE package. (4) VDDSHV1 and VDDSHV2 are merged in the ZCE package. The maximum current rating for VDDSHV1 on the ZCE package is the sum of VDDSHV1 and VDDSHV2 shown in this table. Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 79 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 3.2 www.ti.com Recommended Operating Conditions The device is used under the recommended operating conditions described in Table 3-4. Table 3-3. Reliability Data Operating Condition Commercial VDD_MPU(1)(2) VDD_CORE(2) Junction Temp (Tj) Industrial Life Time (POH)(3) Junction Temp (Tj) Extended Life Time (POH)(3) Junction Temp (Tj) Life Time (POH)(3) Turbo 1.26 V ±4% 1.1 V ±4% 0°C to 90°C TBD -40°C to 90°C TBD -40°C to 105°C TBD OPP120 1.2 V ±4% 1.1 V ±4% 0°C to 90°C 100K -40°C to 90°C 100K -40°C to 105°C 100K OPP100 1.1 V ±4% 1.1 V ±4% 0°C to 90°C 100K -40°C to 90°C 100K -40°C to 105°C 100K OPP50 0.95 V ±4% 0.95 V ±4% 0°C to 90°C 100K -40°C to 90°C 100K -40°C to 105°C 100K (1) Not available on the ZCE package. VDD_MPU is merged with VDD_CORE on the ZCE package. (2) Voltage specification at the device package pin. (3) POH = Power-on hours when the device is fully functional. NOTE Logic functions and parameter values are not assured out of the range specified in the recommended operating conditions. PRODUCT PREVIEW Table 3-4. Recommended Operating Conditions PARAMETER MIN NOM MAX UNIT Supply voltage range for core domain; OPP100 1.06 1.1 1.15 V Supply voltage range for core domain; OPP50 0.91 0.95 0.99 V Supply voltage range for MPU domain; Turbo 1.21 1.26 1.31 Supply voltage range for MPU domain; OPP120 1.15 1.2 1.25 Supply voltage range for MPU domain; OPP100 1.06 1.1 1.15 Supply voltage range for MPU domain; OPP50 0.91 0.95 0.99 CAP_VDD_RTC(2) Supply voltage range for RTC domain input/LDO output 1.06 1.1 1.15 V VDDS_RTC Supply voltage range for RTC domain 1.71 1.8 1.89 V Supply voltage range for DDR IO domain (DDR2) 1.71 1.8 1.89 Supply voltage range for DDR IO domain (DDR3) 1.43 1.5 1.58 VDDS(3) Supply voltage range for all dual-voltage IO domains 1.71 1.8 1.89 V VDDS_SRAM_CORE_BG Supply voltage range for Core SRAM LDOs, Analog 1.71 1.8 1.89 V VDDS_SRAM_MPU_BB Supply voltage range for MPU SRAM LDOs, Analog 1.71 1.8 1.89 V VDDS_PLL_DDR Supply voltage range for DPLL DDR, Analog 1.71 1.8 1.89 V VDDS_PLL_CORE_LCD Supply voltage range for DPLL CORE and LCD, Analog 1.71 1.8 1.89 V VDDS_PLL_MPU Supply voltage range for DPLL MPU, Analog 1.71 1.8 1.89 V SUPPLY NAME VDD_CORE (1) VDD_MPU VDDS_DDR 80 DESCRIPTION Device Operating Conditions V V Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com PARAMETER SUPPLY NAME DESCRIPTION MIN NOM MAX UNIT VDDS_OSC Supply voltage range for system oscillator IO's, Analog 1.71 1.8 1.89 V VDDA1P8V_USB0 Supply voltage range for USB PHY, Analog, 1.8V 1.71 1.8 1.89 V VDDA1P8V_USB1(4) Supply voltage range for USB PHY, Analog, 1.8V 1.71 1.8 1.89 V VDDA3P3V_USB0 Supply voltage range for USB PHY, Analog, 3.3V 3.14 3.3 3.47 V VDDA3P3V_USB1(4) Supply voltage range for USB PHY, Analog, 3.3V 3.14 3.3 3.47 V VDDA_ADC Supply voltage range for ADC, Analog 1.71 1.8 1.89 V VDDSHV1 Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV2(4) Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV3(4) Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV4 Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV5 Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV6 Supply voltage range for dual-voltage IO domain (1.8-V operation) 1.71 1.8 1.89 V VDDSHV1 Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V VDDSHV2(4) Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V VDDSHV3(4) Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V VDDSHV4 Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V VDDSHV5 Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V VDDSHV6 Supply voltage range for dual-voltage IO domain (3.3-V operation) 3.14 3.3 3.47 V DDR_VREF Voltage range for DDR SSTL/HSTL reference input (DDR2/DDR3) 0.49*VDDS_DDR 0.50*VDDS_DDR 0.51*VDDS_DDR V USB0_VBUS Voltage range for USB VBUS comparator input 0 5 V USB1_VBUS(4) Voltage range for USB VBUS comparator input 0 5 V USB0_ID Voltage range for the USB ID input 1.71 1.89 V 1.8 Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated PRODUCT PREVIEW Table 3-4. Recommended Operating Conditions (continued) 81 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-4. Recommended Operating Conditions (continued) PARAMETER SUPPLY NAME USB1_ID(4) DESCRIPTION Voltage range for the USB ID input Commercial Temperature Operating Temperature Range, Tj MIN NOM MAX UNIT 1.71 1.8 1.89 V 0 90 Industrial Temperature -40 90 Extended Temperature -40 105 °C (1) Not available on the ZCE package. VDD_MPU is merged with VDD_CORE on the ZCE package. (2) This supply is sourced from an internal LDO when RTC_KALDO_ENn is low. If RTC_KALDO_ENn is high, this supply must be sourced from an external power supply. (3) VDDS should be supplied irrespective of 1.8-V or 3.3-V mode of operation of the dual-voltage IOs. (4) Not available on the ZCE package. Table 3-5. Operating Performance Points for ZCZ Package(1) OPP VDD_MPU(2) VDD_CORE(2) DDR3(3) ARM (A8) DDR2(3) mDDR(3) L3/L4 (4) PRODUCT PREVIEW Turbo 1.26 V ±4% 1.1 V ±4% 720 MHz 303 MHz 266 MHz 200 MHz 200/100 MHz OPP120 1.2 V ±4% 1.1 V ±4% 600 MHz 303 MHz(4) 266 MHz 200 MHz 200/100 MHz OPP100 1.1 V ±4% 1.1 V ±4% 500 MHz 303 MHz(4) 266 MHz 200 MHz 200/100 MHz OPP50 0.95 V ±4% 0.95 V ±4% 275 MHz - 125 MHz 90 MHz 100/50 MHz (1) Frequencies in this table indicate maximum performance for a given OPP condition. (2) Interfaces in this row are validated and available on OPP50. (3) This parameter represents the maximum memory clock frequency. Since data is transferred on both edges of the clock, double-data rate (DDR), the maximum data rate is two times the maximum memory clock frequency defined in this table. (4) The JEDEC JESD79-3E specification defines the maximum clock period of 3.3 ns for all standard speed bin DDR3 memory devices. Therefore, all standard speed bin DDR3 memory devices are required to operate at 303 MHz. Table 3-6. Operating Performance Points for ZCE Package(1) OPP VDD_CORE(2) ARM (A8) DDR3(3) DDR2(3) mDDR(3) L3/L4 OPP100 1.1 V ±4% 500 MHz 303 MHz(4) 266 MHz 200 MHz 200/100 MHz OPP50 0.95 V ±4% 275 MHz - 125 MHz 90 MHz 100/50 MHz (1) Frequencies in this table indicate maximum performance for a given OPP condition. (2) Interfaces in this row are validated and available on OPP50. (3) This parameter represents the maximum memory clock frequency. Since data is transferred on both edges of the clock, double-data rate (DDR), the maximum data rate is two times the maximum memory clock frequency defined in this table. (4) The JEDEC JESD79-3E specification defines the maximum clock period of 3.3 ns for all standard-speed bin DDR3 memory devices. Therefore, all standard-speed bin DDR3 memory devices are required to operate at 303 MHz. 82 Device Operating Conditions Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 3.3 DC Electrical Characteristics Table 3-7 summarizes the dc electrical characteristics. Note: The interfaces or signals described in Table 3-7 correspond to the interfaces or signals available in multiplexing mode 0. All interfaces or signals multiplexed on the terminals described in Table 3-7 have the same dc electrical characteristics. Table 3-7. DC Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature (Unless Otherwise Noted) PARAMETER MIN NOM MAX UNIT DDR_RESETn,DDR_CSn0,DDR_CKE,DDR_CK,DDR_CKn,DDR_CASn,DDR_RASn,DDR_WEn,DDR_BA0,DDR_BA1,DDR_BA2,DDR_A 0,DDR_A1,DDR_A2,DDR_A3,DDR_A4,DDR_A5,DDR_A6,DDR_A7,DDR_A8,DDR_A9,DDR_A10,DDR_A11,DDR_A12,DDR_A13,DDR_A 14,DDR_A15,DDR_ODT,DDR_D0,DDR_D1,DDR_D2,DDR_D3,DDR_D4,DDR_D5,DDR_D6,DDR_D7,DDR_D8,DDR_D9,DDR_D10,DDR_ D11,DDR_D12,DDR_D13,DDR_D14,DDR_D15,DDR_DQM0,DDR_DQM1,DDR_DQS0,DDR_DQSn0,DDR_DQS1,DDR_DQSn1 pins (mDDR - LVCMOS mode) 0.65 * VDDS_DDR High-level input voltage VIL Low-level input voltage VHYS Hysteresis voltage at an input VOH High level output voltage, driver enabled, pullup or pulldown disbaled IOH = 8 mA VOL Low level output voltage, driver enabled, pullup or pulldown disbaled IOL = 8 mA V 0.07 Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ V 0.25 V VDDS_DDR 0.4 V 0.4 Input leakage current, Receiver disabled, pullup or pulldown inhibited II 0.35 *VDDS_DDR V 10 -240 -80 80 240 Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. 10 µA µA DDR_RESETn,DDR_CSn0,DDR_CKE,DDR_CK,DDR_CKn,DDR_CASn,DDR_RASn,DDR_WEn,DDR_BA0,DDR_BA1,DDR_BA2,DDR_A 0,DDR_A1,DDR_A2,DDR_A3,DDR_A4,DDR_A5,DDR_A6,DDR_A7,DDR_A8,DDR_A9,DDR_A10,DDR_A11,DDR_A12,DDR_A13,DDR_A 14,DDR_A15,DDR_ODT,DDR_D0,DDR_D1,DDR_D2,DDR_D3,DDR_D4,DDR_D5,DDR_D6,DDR_D7,DDR_D8,DDR_D9,DDR_D10,DDR_ D11,DDR_D12,DDR_D13,DDR_D14,DDR_D15,DDR_DQM0,DDR_DQM1,DDR_DQS0,DDR_DQSn0,DDR_DQS1,DDR_DQSn1 pins (DDR2 - SSTL mode) VIH High-level input voltage DDR_VREF + 0.125 VIL Low-level input voltage VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 8 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 8 mA VDDS_DDR 0.125 NA Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. V 0.4 V 10 -240 -80 80 240 10 Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated V V VDDS_DDR 0.4 Input leakage current, Receiver disabled, pullup or pulldown inhibited II V µA µA 83 PRODUCT PREVIEW VIH AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-7. DC Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature (Unless Otherwise Noted) (continued) PARAMETER MIN NOM MAX UNIT DDR_RESETn,DDR_CSn0,DDR_CKE,DDR_CK,DDR_CKn,DDR_CASn,DDR_RASn,DDR_WEn,DDR_BA0,DDR_BA1,DDR_BA2,DDR_A 0,DDR_A1,DDR_A2,DDR_A3,DDR_A4,DDR_A5,DDR_A6,DDR_A7,DDR_A8,DDR_A9,DDR_A10,DDR_A11,DDR_A12,DDR_A13,DDR_A 14,DDR_A15,DDR_ODT,DDR_D0,DDR_D1,DDR_D2,DDR_D3,DDR_D4,DDR_D5,DDR_D6,DDR_D7,DDR_D8,DDR_D9,DDR_D10,DDR_ D11,DDR_D12,DDR_D13,DDR_D14,DDR_D15,DDR_DQM0,DDR_DQM1,DDR_DQS0,DDR_DQSn0,DDR_DQS1,DDR_DQSn1 pins (DDR3 - HSTL mode) VIH High-level input voltage DDR_VREF + 0.1 VIL Low-level input voltage VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 8 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 8 mA V VDDS_DDR 0.1 NA Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled PRODUCT PREVIEW IOZ V VDDS_DDR 0.4 V 0.4 Input leakage current, Receiver disabled, pullup or pulldown inhibited II V V 10 -240 -80 80 240 Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. 10 µA µA ECAP0_IN_PWM0_OUT,UART0_CTSn,UART0_RTSn,UART0_RXD,UART0_TXD,UART1_CTSn,UART1_RTSn,UART1_RXD,UART1_T XD,I2C0_SDA,I2C0_SCL,XDMA_EVENT_INTR0,XDMA_EVENT_INTR1,WARMRSTn,PWRONRSTn,NMIn,TMS,TDO,USB0_DRVVBUS,U SB1_DRVVBUS (VDDSHV6 = 1.8 V) VIH High-level input voltage 0.65 * VDDSHV6 VIL Low-level input voltage VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 4 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 4 mA V 0.18 Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ 84 0.305 V V 0.45 V 5 -161 -100 -52 52 100 170 Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. Device Operating Conditions V VDDSHV6 0.45 Input leakage current, Receiver disabled, pullup or pulldown inhibited II 0.35 * VDDSHV6 5 µA µA Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-7. DC Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature (Unless Otherwise Noted) (continued) PARAMETER MIN NOM MAX UNIT ECAP0_IN_PWM0_OUT,UART0_CTSn,UART0_RTSn,UART0_RXD,UART0_TXD,UART1_CTSn,UART1_RTSn,UART1_RXD,UART1_T XD,I2C0_SDA,I2C0_SCL,XDMA_EVENT_INTR0,XDMA_EVENT_INTR1,WARMRSTn,PWRONRSTn,NMIn,TMS,TDO,USB0_DRVVBUS,U SB1_DRVVBUS (VDDSHV6 = 3.3 V) High-level input voltage VIL Low-level input voltage 2 VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 4 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 4 mA V 0.265 Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ V 0.44 V VDDSHV6 0.2 V 0.2 Input leakage current, Receiver disabled, pullup or pulldown inhibited II 0.8 V 18 -243 -100 -19 51 110 210 Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. 18 µA µA PRODUCT PREVIEW VIH TCK (VDDSHV6 = 1.8 V) VIH High-level input voltage VIL Low-level input voltage VHYS Hysteresis voltage at an input II Input leakage current, Receiver disabled, pullup or pulldown inhibited Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled 1.45 V 0.46 V 5 µA 0.4 V -161 -100 -52 52 100 170 TCK (VDDSHV6 = 3.3 V) VIH High-level input voltage VIL Low-level input voltage VHYS Hysteresis voltage at an input 2.15 V 0.46 0.4 V Input leakage current, Receiver disabled, pullup or pulldown inhibited II Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled 18 -243 -100 -19 51 110 210 Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated V µA 85 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-7. DC Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature (Unless Otherwise Noted) (continued) PARAMETER MIN NOM MAX UNIT All other LVCMOS pins (VDDSHVx = 1.8 V; x=1-6) VIH High-level input voltage 0.65 * VDDSHVx VIL Low-level input voltage VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 6 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 6 mA V 0.18 Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ V 0.305 V VDDSHVx 0.45 V 0.45 Input leakage current, Receiver disabled, pullup or pulldown inhibited II 0.35 * VDDSHVx V 5 -161 -100 -52 52 100 170 PRODUCT PREVIEW Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. 5 µA µA All other LVCMOS pins (VDDSHVx = 3.3 V; x=1-6) VIH High-level input voltage VIL Low-level input voltage 2 VHYS Hysteresis voltage at an input VOH High-level output voltage, driver enabled, pullup or pulldown disbaled IOH = 6 mA VOL Low-level output voltage, driver enabled, pullup or pulldown disbaled IOL = 6 mA V 0.265 Input leakage current, Receiver disabled, pullup enabled Input leakage current, Receiver disabled, pulldown enabled IOZ 86 V V 0.2 V 18 -243 -100 -19 51 110 210 Total leakage current through the PAD connection of a driver/receiver combination that may include a pullup or pulldown. The driver output is disabled and the pullup or pulldown is inhibited. Device Operating Conditions V 0.44 VDDSHVx 0.2 Input leakage current, Receiver disabled, pullup or pulldown inhibited II 0.8 18 µA µA Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 3.4 External Capacitors To improve module performance, decoupling capacitors are required to suppress the switching noise generated by high frequency and to stabilize the supply voltage. A decoupling capacitor is most effective when it is close to the device, because this minimizes the inductance of the circuit board wiring and interconnects. 3.4.1 Voltage Decoupling Capacitors Table 3-8 summarizes the Core voltage decoupling characteristics. 3.4.1.1 Core Voltage Decoupling Capacitors To improve module performance, decoupling capacitors are required to suppress high-frequency switching noise and to stabilize the supply voltage. A decoupling capacitor is most effective when located close to the AM335x device, because this minimizes the inductance of the circuit board wiring and interconnects. Table 3-8. Core Voltage Decoupling Characteristics MIN TYP MAX UNIT CVDD_CORE(1) PARAMETER TBD 10.08 TBD μF CVDD_MPU(2)(3) TBD 10.05 TBD μF PRODUCT PREVIEW (1) The typical value corresponds to 1 cap of 10 µF and 8 caps of 10 nF. (2) Not available on the ZCE package. VDD_MPU is merged with VDD_CORE on the ZCE package. (3) The typical value corresponds to 1 cap of 10 µF and 5 caps of 10 nF. 3.4.1.2 IO and Analog Voltage Decoupling Capacitors Table 3-9 summarizes the power-supply decoupling capacitor recommendations. Table 3-9. Power-Supply Decoupling Capacitor Characteristics MIN TYP MAX UNIT CVDDA_ADC PARAMETER TBD 10 TBD nF CVDDA1P8V_USB0 TBD 10 TBD nF CCVDDA3P3V_USB0 TBD 10 TBD nF CVDDA1P8V_USB1(1) CVDDA3P3V_USB1(1) CVDDS(2) CVDDS_DDR(3)(4) TBD 10 TBD nF TBD 10 TBD nF TBD 10.04 TBD µF TBD 10.06 TBD µF CVDDS_OSC TBD 10 TBD nF CVDDS_PLL_DDR TBD 10 TBD nF CVDDS_PLL_CORE_LCD TBD 10 TBD nF CVDDS_SRAM_CORE_BG TBD 10 TBD nF CVDDS_SRAM_MPU_BB TBD 10 TBD nF CVDDS_PLL_MPU TBD 10 TBD nF CVDDS_RTC TBD 10 TBD nF CVDDSHV1(5) TBD 10.02 TBD µF CVDDSHV2(1)(5) TBD 10.02 TBD µF (1)(5) TBD 10.02 TBD µF CVDDSHV3 Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 87 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 3-9. Power-Supply Decoupling Capacitor Characteristics (continued) MIN TYP MAX UNIT CVDDSHV4(5) PARAMETER TBD 10.02 TBD µF (5) TBD 10.02 TBD µF CVDDSHV6(3) TBD 10.06 TBD µF CVDDSHV5 (1) Not available on the ZCE package. (2) Typical values consist of 1 cap of 10 µF and 4 caps of 10 nF. (3) Typical values consist of 1 cap of 10 µF and 6 caps of 10 nF. (4) For more details on decoupling capacitor requirements for the mDDR(LPDDR)/DDR2/DDR3 memory interface, see Section 5.4.2.2.2.6 and Section 5.4.2.2.2.7. (5) Typical values consist of 1 cap of 10 µF and 2 caps of 10 nF. 3.4.2 Output Capacitors Internal low dropout output (LDO) regulators require external capacitors to stabilize their outputs. These capacitors should be placed as close as possible to the respective terminals of the AM335x device. Table 3-10 summarizes the LDO output capacitor recommendations. Table 3-10. Output Capacitor Characteristics PRODUCT PREVIEW MIN TYP MAX CCAP_VDD_SRAM_CORE(1) PARAMETER 0.7 1 1.3 UNIT μF CCAP_VDD_RTC(1)(2) 0.7 1 1.3 μF CCAP_VDD_SRAM_MPU(1) 0.7 1 1.3 μF CCAP_VBB_MPU(1) 0.7 1 1.3 μF (1) LDO regulator outputs should not be used as a power source for any external components. (2) The CAP_VDD_RTC terminal operates as an input to the RTC core voltage domain when the RTC_KLDO_ENn terminal is high. 88 Device Operating Conditions Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Figure 3-1 illustrates an example of the external capacitors. AM335x Device VDDS_PLL_MPU MPU PLL VDD_MPU CVDDS_PLL_MPU MPU CVDD_MPU VDDS_PLL_CORE_LCD CORE PLL VDD_CORE CORE LCD PLL CVDDS_PLL_CORE_LCD CAP_VBB_MPU CVDD_CORE CCAP_VBB_MPU CVDDSHV1 VDDS_SRAM_MPU_BB VDDSHV1 IOs MPU SRAM LDO Back Bias LDO CVDDSHV2 VDDSHV2 IOs CVDDSHV3 VDDSHV3 IOs CVDDSHV4 VDDSHV4 IOs CVDDSHV5 VDDSHV5 IOs CVDDSHV6 VDDSHV6 IOs CVDDS_SRAM_MPU_BB CAP_VDD_SRAM_MPU CCAP_VDD_SRAM_MPU VDDS_SRAM_CORE_BG CORE SRAM LDO Band Gap Reference CVDDS_SRAM_CORE_BG CAP_VDD_SRAM_CORE CCAP_VDD_SRAM_CORE VDDA_3P3V_USBx CVDDA_3P3V_USBx VSSA_USB CVDDS_DDR USB PHYx CVDDA_1P8V_USBx VSSA_USB VDDS_DDR IOs VDDA_ADC ADC CVDDS_RTC VDDA_1P8V_USBx VDDS_RTC IOs CVDDA_ADC VSSA_ADC VDDS_OSC CVDDS_OSC VDDS_PLL_DDR CVDDS_PLL_DDR DDR PLL CAP_VDD_RTC RTC A. B. CCAP_VDD_RTC Decoupling capacitors must be placed as closed as possible to the power terminal. Choose the ground located closest to the power pin for each decoupling capacitor. In case of interconnecting powers, first insert the decoupling capacitor and then interconnect the powers. The decoupling capacitor value depends on the board characteristics. Figure 3-1. External Capacitors Device Operating Conditions Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 89 PRODUCT PREVIEW CVDDS VDDS IO AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 3.4.3 www.ti.com VDD_MPU_MON Connections Figure 3-2 shows the VDD_MPU_MON connectivity. VDD_MPU_MON connectivity is available only on the ZCZ package. VDD_MPU AM335x Device Power Management IC VDD_MPU_MON Vfeedback Connection for VDD_MPU_MON if voltage monitoring is used VDD_MPU PRODUCT PREVIEW AM335x Device Power Source VDD_MPU_MON Connection for VDD_MPU_MON if voltage monitoring is NOT used Figure 3-2. VDD_MPU_MON Connectivity 90 Device Operating Conditions Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 4 Power and Clocking 4.1 Power Supplies 4.1.1 Power-Up Sequencing 1.8V VDDS_RTC 1.8V RTC_PWRONRSTn 1.8V PMIC_POWER_EN 1.8V All 1.8-V Supplies 1.8V/1.5V VDDS_DDR PRODUCT PREVIEW 3.3V IO 3.3-V Supplies 1.1V VDD_CORE, VDD_MPU 3.3V PWRONRSTn CLK_M_OSC A. B. C. D. E. F. RTC_PWRONRSTn should be asserted for at least 1ms. When using the ZCZ package option, VDD_MPU and VDD_CORE power inputs may be powered from the same source if the application only uses operating performance points (OPPs) that define a common power supply voltage for VDD_MPU and VDD_CORE. The ZCE package option has the VDD_MPU domain merged with the VDD_CORE domain. If a USB port is not used, the respective VDDA1P8V_USB terminal may be connected to any 1.8-V power supply and the respective VDDA3P3V_USB terminal may be connected to any 3.3-V power supply. If the system does not have a 3.3-V power supply, the VDDA3P3V_USB terminal may be connected to ground. If the system uses mDDR or DDR2 memory devices, VDDS_DDR can be ramped simultaneously with the other 1.8-V I/O power supplies. VDDS_RTC can be ramped independent of other power supplies if PMIC_PWR_EN functionality is not required. If VDDS_RTC is ramped after VDD_CORE, there might be a small amount of additional leakage current on VDD_CORE. The power sequence shown provides the lowest leakage option. To configure VDDSHVx [1-6] as 1.8 V, power up the respective VDDSHVx [1-6] to 1.8 V following the recommended sequence. To configure VDDSHVx [1-6] as 3.3 V, power up the respective VDDSHVx [1-6] to 3.3 V following the recommended sequence. Figure 4-1. Preferred Power-Supply Sequencing with Dual-Voltage I/Os Configured as 3.3 V Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 91 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 1.8V VDDS_RTC 1.8V RTC_PWRONRSTn 1.8V PMIC_POWER_EN 3.3V All 1.8-V Supplies All 3.3-V Supplies 1.8V See Notes Below 1.8V/1.5V VDDS_DDR 1.1V VDD_CORE, VDD_MPU PRODUCT PREVIEW PWRONRSTn CLK_M_OSC A. B. C. D. E. F. G. RTC_PWRONRSTn should be asserted for at least 1ms. The 3.3-V I/O power supplies may be ramped simultaneously with the 1.8-V I/O power supplies if the voltage sourced by any 3.3-V power supplies does not exceed the voltage sourced by any 1.8-V power supply by more than 2 V. Serious reliability issues may occur if the system power supply design allows any 3.3-V I/O power supplies to exceed any 1.8-V I/O power supplies by more than 2 V. When using the ZCZ package option, VDD_MPU and VDD_CORE power inputs may be powered from the same source if the application only uses operating performance points (OPPs) that define a common power supply voltage for VDD_MPU and VDD_CORE. The ZCE package option has the VDD_MPU domain merged with the VDD_CORE domain. If a USB port is not used, the respective VDDA1P8V_USB terminal may be connected to any 1.8-V power supply and the respective VDDA3P3V_USB terminal may be connected to any 3.3-V power supply. If the system does not have a 3.3-V power supply, the VDDA3P3V_USB terminal may be connected to ground. If the system uses mDDR or DDR2 memory devices, VDDS_DDR can be ramped simultaneously with the other 1.8-V I/O power supplies. VDDS_RTC can be ramped independent of other power supplies if PMIC_PWR_EN functionality is not required. If VDDS_RTC is ramped after VDD_CORE, there might be a small amount of additional leakage current on VDD_CORE. The power sequence shown provides the lowest leakage option. To configure VDDSHVx [1-6] as 1.8 V, power up the respective VDDSHVx [1-6] to 1.8 V following the recommended sequence. To configure VDDSHVx [1-6] as 3.3 V, power up the respective VDDSHVx [1-6] to 3.3 V following the recommended sequence. Figure 4-2. Alternate Power-Supply Sequencing with Dual-Voltage I/Os Configured as 3.3 V 92 Power and Clocking Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 1.8V VDDS_RTC 1.8V RTC_PWRONRSTn 1.8V PMIC_POWER_EN 1.8V All 1.8-V Supplies 1.8V/1.5V VDDS_DDR 3.3V All 3.3-V Supplies 1.1V VDD_CORE, VDD_MPU PRODUCT PREVIEW 1.8V PWRONRSTn CLK_M_OSC A. B. C. D. E. F. RTC_PWRONRSTn should be asserted for at least 1ms. When using the ZCZ package option, VDD_MPU and VDD_CORE power inputs may be powered from the same source if the application only uses operating performance points (OPPs) that define a common power supply voltage for VDD_MPU and VDD_CORE. The ZCE package option has the VDD_MPU domain merged with the VDD_CORE domain. If a USB port is not used, the respective VDDA1P8V_USB terminal may be connected to any 1.8-V power supply and the respective VDDA3P3V_USB terminal may be connected to any 3.3-V power supply. If the system does not have a 3.3-V power supply, the VDDA3P3V_USB terminal may be connected to ground. If the system uses mDDR or DDR2 memory devices, VDDS_DDR can be ramped simultaneously with the other 1.8-V I/O power supplies. VDDS_RTC can be ramped independent of other power supplies if PMIC_PWR_EN functionality is not required. If VDDS_RTC is ramped after VDD_CORE, there might be a small amount of additional leakage current on VDD_CORE. The power sequence shown provides the lowest leakage option. To configure VDDSHVx [1-6] as 1.8 V, power up the respective VDDSHVx [1-6] to 1.8 V following the recommended sequence. To configure VDDSHVx [1-6] as 3.3 V, power up the respective VDDSHVx [1-6] to 3.3 V following the recommended sequence. Figure 4-3. Power-Supply Sequencing with Dual-Voltage I/Os Configured as 1.8 V Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 93 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 1.8V 1.1V VDDS_RTC, CAP_VDD_RTC 1.8V RTC_PWRONRSTn 1.8V PMIC_POWER_EN 1.8V VDDSHV 1-6 All other 1.8-V Supplies 1.8V/1.5V VDDS_DDR 3.3V All 3.3-V Supplies 1.1V VDD_CORE, VDD_MPU PRODUCT PREVIEW 1.8V PWRONRSTn CLK_M_OSC A. B. C. D. E. F. G. RTC_PWRONRSTn should be asserted for at least 1ms. The CAP_VDD_RTC terminal operates as an input to the RTC core voltage domain when the internal RTC LDO is disabled by connecting the RTC_KALDO_ENn terminal to VDDS_RTC. If the internal RTC LDO is disabled, CAP_VDD_RTC should be sourced from an external 1.1-V power supply. When using the ZCZ package option, VDD_MPU and VDD_CORE power inputs may be powered from the same source if the application only uses operating performance points (OPPs) that define a common power supply voltage for VDD_MPU and VDD_CORE. The ZCE package option has the VDD_MPU domain merged with the VDD_CORE domain. If a USB port is not used, the respective VDDA1P8V_USB terminal may be connected to any 1.8-V power supply and the respective VDDA3P3V_USB terminal may be connected to any 3.3-V power supply. If the system does not have a 3.3-V power supply, the VDDA3P3V_USB terminal may be connected to ground. If the system uses mDDR or DDR2 memory devices, VDDS_DDR can be ramped simultaneously with the other 1.8-V I/O power supplies. VDDS_RTC should be ramped at the same time or before CAP_VDD_RTC, but these power inputs can be ramped independent of other power supplies if PMIC_PWR_EN functionality is not required. If CAP_VDD_RTC is ramped after VDD_CORE, there might be a small amount of additional leakage current on VDD_CORE. The power sequence shown provides the lowest leakage option. To configure VDDSHVx [1-6] as 1.8 V, power up the respective VDDSHVx [1-6] to 1.8 V following the recommended sequence. To configure VDDSHVx [1-6] as 3.3 V, power up the respective VDDSHVx [1-6] to 3.3 V following the recommended sequence. Figure 4-4. Power-Supply Sequencing with Internal RTC LDO Disabled 94 Power and Clocking Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 1.8V VDDS_RTC, All other 1.8-V Supplies 1.8V/1.5V VDDS_DDR 3.3V All 3.3-V Supplies 1.1V VDD_CORE, VDD_MPU CAP_VDD_RTC PWRONRSTn CLK_M_OSC B. C. D. E. F. CAP_VDD_RTC terminal operates as an input to the RTC core voltage domain when the internal RTC LDO is disabled by connecting the RTC_KALDO_ENn terminal to VDDS_RTC. If the internal RTC LDO is disabled, CAP_VDD_RTC should be sourced from an external 1.1-V power supply. The PMIC_POWER_EN output cannot be used when the RTC is disabled. When using the ZCZ package option, VDD_MPU and VDD_CORE power inputs may be powered from the same source if the application only uses operating performance points (OPPs) that define a common power supply voltage for VDD_MPU and VDD_CORE. The ZCE package option has the VDD_MPU domain merged with the VDD_CORE domain. If a USB port is not used, the respective VDDA1P8V_USB terminal may be connected to any 1.8-V power supply and the respective VDDA3P3V_USB terminal may be connected to any 3.3-V power supply. If the system does not have a 3.3-V power supply, the VDDA3P3V_USB terminal may be connected to ground. If the system uses mDDR or DDR2 memory devices, VDDS_DDR can be ramped simultaneously with the other 1.8-V I/O power supplies. VDDS_RTC should be ramped at the same time or before CAP_VDD_RTC, but these power inputs can be ramped independent of other power supplies if PMIC_PWR_EN functionality is not required. If CAP_VDD_RTC is ramped after VDD_CORE, there might be a small amount of additional leakage current on VDD_CORE. The power sequence shown provides the lowest leakage option. To configure VDDSHVx [1-6] as 1.8 V, power up the respective VDDSHVx [1-6] to 1.8 V following the recommended sequence. To configure VDDSHVx [1-6] as 3.3 V, power up the respective VDDSHVx [1-6] to 3.3 V following the recommended sequence. PRODUCT PREVIEW A. Figure 4-5. Power-Supply Sequencing with RTC Feature Disabled 4.1.2 Power-Down Sequencing PWRONRSTn input terminal should be taken low, which stops all internal clocks before power supplies are turned off. All other external clocks to the device should be shut off. The preferred way to sequence power down is to have all the power supplies ramped down sequentially in the exact reverse order of the power-up sequencing. In other words, the power supply that has been ramped up first should be the last one that should be ramped down. This will ensure there would be no spurious current paths during the power-down sequence. The VDDS power supply must ramp down after all 3.3-V VDDSHVx [1-6] power supplies. If it is desired to ramp down VDDS and VDDSHVx [1-6] simultaneously, it should always be ensured that the difference between VDDS and VDDSHVx [1-6] during the entire power-down sequence is <2 V. If this is violated it can result in reliability risks for the device. Further, it should also be ensured that the VDDS supply should be ≥1.5 V of all the other supplies in the system during the ramp down. If there is no 3.3-V VDDSHVx [1-6] power supply, the VDDS power supply may ramp down at the same time or after all 1.8-V VDDSHVx[1-6] power supplies. It should be ensured that the VDDS supply should be ≥1.5 V of all the other supplies in the system during ramp down. Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 95 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 4.2 www.ti.com Clock Specifications 4.2.1 Input Clock Specifications The AM335x device has two clock inputs. Each clock input passes through an internal oscillator which can be connected to an external crystal circuit (oscillator mode) or external LVCMOS square-wave digital clock source (bypass mode). The oscillators automatically operate in bypass mode when their input is connected to an external LVCMOS square-wave digital clock source. The oscillator associated with a specific clock input must be enabled when the clock input is being used in either oscillator mode or bypass mode. The OSC1 oscillator provides a 32.768-kHz reference clock to the real-time clock (RTC) and is connected to the RTC_XTALIN and RTC_XTALOUT terminals. This clock source is referred to as the 32K oscillator (CLK_32K_RTC) in the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). OSC1 is disabled by default after power is applied. This clock input is optional and may not be required if the RTC is configured to receive a clock from the internal 32k RC oscillator (CLK_RC32K) or peripheral PLL (CLK_32KHZ) which receives a reference clock from the OSC0 input. PRODUCT PREVIEW The OSC0 oscillator provides a 19.2-MHz, 24-MHz, 25-MHz, or 26-MHz reference clock which is used to clock all non-RTC functions and is connected to the XTALIN and XTALOUT terminals. This clock source is referred to as the master oscillator (CLK_M_OSC) in the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). OSC0 is enabled by default after power is applied. For more information related to recommended circuit topologies and crystal oscillator circuit requirements for these clock inputs, see Section 4.2.2. 4.2.2 Input Clock Requirements 4.2.2.1 OSC0 Internal Oscillator Clock Source Figure 4-6 shows the recommended crystal circuit. It is recommended that pre-production printed circuit board (PCB) designs include the two optional resistors Rbias and Rd in case they are required for proper oscillator operation when combined with production crystal circuit components. In most cases, Rbias will not be required and Rd will be a zero ohm resistor. These resistors may be removed from production PCB designs after evaluating oscillator performance with production crystal circuit components installed on pre-production PCBs. The XTALIN terminal has a 15 - 40 kΩ internal pull-down resistor which is enabled when OSC0 is disabled. This internal resistor prevents the XTALIN terminal from floating to an invalid logic level which may increase leakage current through the oscillator input buffer. 96 Power and Clocking Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com AM335x VSS_OSC XTALIN C1 XTALOUT C2 Optional Rbias Optional Rd Crystal B. Oscillator components (Crystal, C1, C2, optional Rbias and Rd) must be located close to the AM335x package. Parasitic capacitance to the printed circuit board (PCB) ground and other signals should be minimized to reduce noise coupled into the oscillator. The VSS_OSC terminal provides a Kelvin ground reference for the external crystal components. External crystal component grounds should only be connected to the VSS_OSC terminal and should not be connected to the PCB ground plane. C1 and C2 represent the total capacitance of the respective PCB trace, load capacitor, and other components (excluding the crystal) connected to each crystal terminal. The value of capacitors C1 and C2 should be selected to provide the total load capacitance, CL, specified by the crystal manufacturer. The total load capacitance is CL = [(C1*C2)/(C1+C2)] + Cshunt, where Cshunt is the crystal shunt capacitance (C0) specified by the crystal manufacturer plus any mutual capacitance (Cpkg + CPCB) seen across the AM335x XTALIN and XTALOUT signals. For recommended values of crystal circuit components, see Table 4-1. PRODUCT PREVIEW A. Figure 4-6. OSC0 Crystal Circuit Schematic Table 4-1. OSC0 Crystal Circuit Requirements NAME DESCRIPTION MIN fxtal Crystal parallel resonance frequency Fundamental mode oscillation only Crystal frequency stability/tolerance TYP MAX 19.2, 24.0, 25.0, or 26.0 UNIT MHz -50.0 50.0 ppm CC1 C1 capacitance 12.0 24.0 pF CC2 C2 capacitance 12.0 24.0 pF Cshunt Shunt capacitance ESR Crystal effective series resistance 5.0 pF fxtal = 19.2 MHz, oscillator has nominal negative resistance of 272 Ω and worst-case negative resistance of 163 Ω 54.4 Ω fxtal = 24.0 MHz, oscillator has nominal negative resistance of 240 Ω and worst-case negative resistance of 144 Ω 48.0 Ω fxtal = 25.0 MHz, oscillator has nominal negative resistance of 233 Ω and worst-case negative resistance of 140 Ω 46.6 Ω fxtal = 26.0 MHz, oscillator has nominal negative resistance of 227 Ω and worst-case negative resistance of 137 Ω 45.3 Ω Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 97 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 4.2.2.2 www.ti.com OSC0 LVCMOS Digital Clock Source Figure 4-7 shows the recommended oscillator connections when OSC0 is connected to an LVCMOS square-wave digital clock source. The LVCMOS clock source is connected to the XTALIN terminal. In this mode of operation, the XTALOUT terminal should not be used to source any external components. The printed circuit board design should provide a mechanism to disconnect the XTALOUT terminal from any external components or signal traces that may couple noise into OSC0 via the XTALOUT terminal. The XTALIN terminal has a 15 - 40 kΩ internal pull-down resistor which is enabled when OSC0 is disabled. This internal resistor prevents the XTALIN terminal from floating to an invalid logic level which may increase leakage current through the oscillator input buffer. AM335x XTALIN VSS_OSC XTALOUT PRODUCT PREVIEW LVCMOS Digital Clock Source Figure 4-7. OSC0 LVCMOS Circuit Schematic 4.2.2.3 OSC1 Internal Oscillator Clock Source Figure 4-8 shows the recommended crystal circuit. It is recommended that pre-production printed circuit board (PCB) designs include the two optional resistors Rbias and Rd in case they are required for proper oscillator operation when combined with production crystal circuit components. In most cases, Rbias will not be required and Rd will be a zero ohm resistor. These resistors may be removed from production PCB designs after evaluating oscillator performance with production crystal circuit components installed on pre-production PCBs. The RTC_XTALIN terminal does not enable an internal pull-down resistor when OSC1 is disabled. If this oscillator is disabled, the RTC_XTALIN terminal may float to an invalid logic level which may increase leakage current through the oscillator input buffer. This should not be an issue for most applications that use this oscillator to source the RTC clock since the RTC requires a continuous clock to maintain time. 98 Power and Clocking Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com AM335x RTC_XTALIN RTC_XTALOUT Optional Rbias Crystal Optional Rd C1 A. B. C2 Oscillator components (Crystal, C1, C2, optional Rbias and Rd) must be located close to the AM335x package. Parasitic capacitance to the printed circuit board (PCB) ground and other signals should be minimized to reduce noise coupled into the oscillator. C1 and C2 represent the total capacitance of the respective PCB trace, load capacitor, and other components (excluding the crystal) connected to each crystal terminal. The value of capacitors C1 and C2 should be selected to provide the total load capacitance, CL, specified by the crystal manufacturer. The total load capacitance is CL = [(C1*C2)/(C1+C2)] + Cshunt, where Cshunt is the crystal shunt capacitance (C0) specified by the crystal manufacturer plus any mutual capacitance (Cpkg + CPCB) seen across the AM335x RTC_XTALIN and RTC_XTALOUT signals. For recommended values of crystal circuit components, see Table 4-2. PRODUCT PREVIEW Figure 4-8. OSC1 Crystal Circuit Schematic Table 4-2. OSC1 Crystal Circuit Requirements NAME DESCRIPTION fxtal Crystal parallel resonance frequency Fundamental mode oscillation only MIN TYP MAX Crystal frequency stability/tolerance Maximum RTC error = 10.512 minutes/year -20.0 20.0 ppm Maximum RTC error = 26.28 minutes/year -50.0 50.0 ppm 32.768 UNIT kHz CC1 C1 capacitance 12.0 24.0 pF CC2 C2 capacitance 12.0 24.0 pF Cshunt Shunt capacitance ESR Crystal effective series resistance 4.2.2.4 fxtal = 32.768 kHz, oscillator has nominal negative resistance of 725 kΩ and worst-case negative resistance of 250 kΩ 5.0 pF 80 kΩ OSC1 LVCMOS Digital Clock Source Figure 4-9 shows the recommended oscillator connections when OSC1 is connected to an LVCMOS square-wave digital clock source. The LVCMOS clock source is connected to the RTC_XTALIN terminal. In this mode of operation, the RTC_XTALOUT terminal should not be used to source any external components. The printed circuit board design should provide a mechanism to disconnect the RTC_XTALOUT terminal from any external components or signal traces that may couple noise into OSC1 via the RTC_XTALOUT terminal. The RTC_XTALIN terminal does not enable an internal pull-down resistor when OSC1 is disabled. If this oscillator is disabled, the RTC_XTALIN terminal may float to an invalid logic level which may increase leakage current through the oscillator input buffer. This should not be an issue for most applications that use this oscillator to source the RTC clock since the RTC requires a continuous clock to maintain time. Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 99 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com AM335x RTC_XTALIN RTC_XTALOUT LVCMOS Digital Clock Source N/C Figure 4-9. OSC1 LVCMOS Circuit Schematic 4.2.2.5 OSC1 Not Used Figure 4-10 shows the recommended oscillator connections when OSC1 is not being used. An external 10 kΩ maximum pull-down resistor should be connected to the RTC_XTALIN terminal to prevent this input from floating to an invalid logic level which may increase leakage current through the oscillator input buffer. The RTC_XTALOUT terminal is a no connect (NC). PRODUCT PREVIEW AM335x RTC_XTALIN RTC_XTALOUT Rpd N/C Figure 4-10. OSC1 Not Used Schematic 4.2.3 Output Clock Specifications The AM335x device has two clock output signals. The CLKOUT1 signal is always a replica of the OSC0 input clock which is referred to as the master oscillator (CLK_M_OSC) in the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). The CLKOUT2 signal can be configured to output the OSC0 input clock, which is referred to as the 32K oscillator (CLK_32K_RTC) in the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73), or four other internal clocks. For more information related to configuring these clock output signals, see the CLKOUT Signals section of the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). 4.2.4 Output Clock Characteristics 4.2.4.1 CLKOUT1 The CLKOUT1 signal can be output on the XDMA_EVENT_INTR0 terminal. This terminal connects to one of seven internal signals via configurable multiplexers. The XDMA_EVENT_INTR0 multiplexer must be configured for Mode 3 to connect the CLKOUT1 signal to the XDMA_EVENT_INTR0 terminal. The default reset configuration of the XDMA_EVENT_INTR0 multiplexer is selected by the logic level applied to the LCD_DATA5 terminal on the rising edge of PWRONRSTn. The XDMA_EVENT_INTR0 multiplexer will be configured to Mode 7 if the LCD_DATA5 terminal is low on the rising edge of PWRONRSTn or Mode 3 if the LCD_DATA5 terminal is high on the rising edge of PWRONRSTn. This allows the CLKOUT1 signal to be output on the XDMA_EVENT_INTR0 terminal without software intervention. In this mode, the output will be held low while PWRONRSTn is active and will begin to toggle after PWRONRSTn is released. 100 Power and Clocking Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 4.2.4.2 CLKOUT2 The CLKOUT2 signal can be output on the XDMA_EVENT_INTR1 terminal. This terminal connects to one of seven internal signals via configurable multiplexers. The XDMA_EVENT_INTR1 multiplexer must be configured for Mode 3 to connect the CLKOUT2 signal to the XDMA_EVENT_INTR1 terminal. PRODUCT PREVIEW The default reset configuration of the XDMA_EVENT_INTR1 multiplexer is always Mode 7. Software must configure the XDMA_EVENT_INTR1 multiplexer to Mode 3 for the CLKOUT2 signal to be output on the XDMA_EVENT_INTR1 terminal. Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Power and Clocking 101 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5 Peripheral Information and Timings The AM335x device contains many peripheral interfaces. In order to reduce package size and cost while maintaining maximum functionality, many of the AM335x terminals can multiplex up to eight signal functions. Although there are many combinations of pin multiplexing that are possible, only a certain number of sets, called IO sets, are valid due to timing limitations. These valid IO sets were carefully chosen to provide many possible application scenarios for the user. Texas Instruments has developed a Windows application called Pin Mux Utility that helps a system designer select the appropriate pin-multiplexing configuration for their AM335x-based product design. This tool provides a way to select valid IO sets of specific peripheral interfaces to ensure that the pin-multiplexing configuration selected for a design only uses valid IO sets supported by the AM335x device. 5.1 5.1.1 Parameter Information Timing Parameters and Board Routing Analysis PRODUCT PREVIEW The timing parameter values specified in this data manual do not include delays by board routings. As a good board design practice, such delays must always be taken into account. Timing values may be adjusted by increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification (IBIS) models to analyze the timing characteristics correctly. If needed, external logic hardware such as buffers may be used to compensate any timing differences. For the mDDR(LPDDR)/DDR2/DDR3 memory interface, it is not necessary to use the IBIS models to analyze timing characteristics. TI provides a PCB routing rules solution that describes the routing rules to ensure the mDDR(LPDDR)/DDR2/DDR3 memory interface timings are met. 5.2 Recommended Clock and Control Signal Transition Behavior All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic manner. 102 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.3 Ethernet Media Access Controller (EMAC)/Switch 5.3.1 Ethernet MAC/Switch Electrical Data/Timing The Ethernet MAC/Switch implemented in the AM335x device supports GMII mode, but the AM335x design does not pin out 9 of the 24 GMII signals. This was done to reduce the total number of package terminals. Therefore, the AM335x device does not support GMII mode. MII mode is supported with the remaining GMII signals. The AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73) and this document may reference internal signal names when discussing peripheral input and output signals since many of the AM335x package terminals can be multiplexed to one of several peripheral signals. For example, the AM335x terminal names for port 1 of the Ethernet MAC/Switch have been changed from GMII to MII to indicate their Mode 0 function, but the internal signal is named GMII. However, documents that describe the Ethernet switch reference these signals by their internal signal name. For a cross-reference of internal signal names to terminal names, see Table 2-7. Operation of the Ethernet MAC/Switch is not supported for OPP50. Table 5-1. Ethernet MAC/Switch Timing Conditions MIN TYP MAX UNIT tR Input signal rise time tF Input signal fall time 1(1) 5(1) ns (1) 5(1) ns 3 30 pF 1 Output Condition CLOAD Output load capacitance (1) Except when specified otherwise. 5.3.1.1 Ethernet MAC/Switch MII Electrical Data/Timing Table 5-2. Timing Requirements for GMII[x]_RXCLK - MII Mode (see Figure 5-1) 10 Mbps NO. MIN TYP 100 Mbps TYP MAX UNIT MAX MIN 399.96 400.04 39.996 40.004 ns 1 tc(RX_CLK) Cycle time, RX_CLK 2 tw(RX_CLKH) Pulse Duration, RX_CLK high 140 260 14 26 ns 3 tw(RX_CLKL) Pulse Duration, RX_CLK low 140 260 14 26 ns 4 tt(RX_CLK) Transition time, RX_CLK 5 ns 5 4 1 2 3 GMII[x]_RXCLK 4 Figure 5-1. GMII[x]_RXCLK Timing - MII Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 103 PRODUCT PREVIEW TIMING CONDITION PARAMETER Input Conditions AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-3. Timing Requirements for GMII[x]_TXCLK - MII Mode (see Figure 5-2) 10 Mbps NO. MIN 100 Mbps TYP MAX MIN TYP MAX UNIT 1 tc(TX_CLK) Cycle time, TX_CLK 399.96 400.04 39.996 40.004 ns 2 tw(TX_CLKH) Pulse Duration, TX_CLK high 140 260 14 26 ns 3 tw(TX_CLKL) Pulse Duration, TX_CLK low 140 260 14 26 ns 4 tt(TX_CLK) Transition time, TX_CLK 5 ns 5 4 1 3 2 GMII[x]_TXCLK 4 Figure 5-2. GMII[x]_TXCLK Timing - MII Mode Table 5-4. Timing Requirements for GMII[x]_RXD[3:0], GMII[x]_RXDV, and GMII[x]_RXER - MII Mode PRODUCT PREVIEW (see Figure 5-3) 10 Mbps NO. 1 2 MIN tsu(RXD-RX_CLK) Setup time, RXD[3:0] valid before RX_CLK tsu(RX_DV-RX_CLK) Setup time, RX_DV valid before RX_CLK tsu(RX_ER-RX_CLK) Setup time, RX_ER valid before RX_CLK th(RX_CLK-RXD) Hold time RXD[3:0] valid after RX_CLK th(RX_CLK-RX_DV) Hold time RX_DV valid after RX_CLK th(RX_CLK-RX_ER) Hold time RX_ER valid after RX_CLK 100 Mbps TYP MAX MIN TYP MAX UNIT 8 8 ns 8 8 ns 1 2 GMII[x]_MRCLK (Input) GMII[x]_RXD[3:0], GMII[x]_RXDV, GMII[x]_RXER (Inputs) Figure 5-3. GMII[x]_RXD[3:0], GMII[x]_RXDV, GMII[x]_RXER Timing - MII Mode 104 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-5. Switching Characteristics for GMII[x]_TXD[3:0], and GMII[x]_TXEN - MII Mode (see Figure 5-4) NO. 1 PARAMETER td(TX_CLK-TXD) Delay time, TX_CLK high to TXD[3:0] valid td(TX_CLK-TX_EN) Delay time, TX_CLK to TX_EN valid 10 Mbps MIN 5 TYP 100 Mbps MAX MIN 25 5 TYP MAX 25 UNIT ns 1 GMII[x]_TXCLK (input) GMII[x]_TXD[3:0], GMII[x]_TXEN (outputs) PRODUCT PREVIEW Figure 5-4. GMII[x]_TXD[3:0], GMII[x]_TXEN Timing - MII Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 105 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.3.1.2 www.ti.com Ethernet MAC/Switch RMII Electrical Data/Timing Table 5-6. Timing Requirements for RMII[x]_REFCLK - RMII Mode (see Figure 5-5) NO. MIN TYP MAX UNIT 1 tc(REF_CLK) Cycle time, REF_CLK 19.999 20.001 ns 2 tw(REF_CLKH) Pulse Duration, REF_CLK high 7 13 ns 3 tw(REF_CLKL) Pulse Duration, REF_CLK low 7 13 ns 1 2 RMII[x]_REFCLK (Input) 3 Figure 5-5. RMII[x]_REFCLK Timing - RMII Mode PRODUCT PREVIEW Table 5-7. Timing Requirements for RMII[x]_RXD[1:0], RMII[x]_CRS_DV, and RMII[x]_RXER - RMII Mode (see Figure 5-6) NO. 1 2 MIN tsu(RXD-REF_CLK) Setup time, RXD[1:0] valid before REF_CLK tsu(CRS_DV-REF_CLK) Setup time, CRS_DV valid before REF_CLK tsu(RX_ER-REF_CLK) Setup time, RX_ER valid before REF_CLK th(REF_CLK-RXD) Hold time RXD[1:0] valid after REF_CLK th(REF_CLK-CRS_DV) Hold time, CRS_DV valid after REF_CLK th(REF_CLK-RX_ER) Hold time, RX_ER valid after REF_CLK TYP MAX UNIT 4 ns 2 ns 1 2 RMII[x]_REFCLK (input) RMII[x]_RXD[1:0], RMII[x]_CRS_DV, RMII[x]_RXER (inputs) Figure 5-6. RMII[x]_RXD[1:0], RMII[x]_CRS_DV, RMII[x]_RXER Timing - RMII Mode 106 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-8. Switching Characteristics for RMII[x]_TXD[1:0], and RMII[x]_TXEN - RMII Mode (see Figure 5-7) NO. 1 2 3 PARAMETER td(REF_CLK-TXD) Delay time, REF_CLK high to TXD[1:0] valid td(REF_CLK-TXEN) Delay time, REF_CLK to TXEN valid tr(TXD) Rise time, TXD outputs tr(TX_EN) Rise time, TX_EN output tf(TXD) Fall time, TXD outputs tf(TX_EN) Fall time, TX_EN output MIN TYP MAX UNIT 2 13 ns 1 5 ns 1 5 ns 1 RMII[x]_REFCLK (Input) RMII[x]_TXD[1:0], RMII[x]_TXEN (Outputs) 2 3 PRODUCT PREVIEW Figure 5-7. RMII[x]_TXD[1:0], RMII[x]_TXEN Timing - RMII Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 107 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.3.1.3 www.ti.com Ethernet MAC/Switch RGMII Electrical Data/Timing RGMII mode is not supported for OPP50. Table 5-9. Timing Requirements for RGMII[x]_RCLK - RGMII Mode (see Figure 5-8) 10 Mbps NO. 1 MIN 100 Mbps TYP MAX MIN TYP 1000 Mbps MAX MIN TYP MAX UNIT tc(RXC) Cycle time, RXC 360 440 36 44 7.2 8.8 ns 2 tw(RXCH) Pulse duration, RXC high 160 240 16 24 3.6 4.4 ns 3 tw(RXCL) Pulse duration, RXC low 160 240 16 24 3.6 4.4 ns 4 tt(RXC) Transition time, RXC 0.75 ns 0.75 0.75 1 4 2 4 3 RGMII[x]_RCLK PRODUCT PREVIEW Figure 5-8. RGMII[x]_RCLK Timing - RGMII Mode Table 5-10. Timing Requirements for RGMII[x]_RD[3:0], and RGMII[x]_RCTL - RGMII Mode (see Figure 5-9) 10 Mbps NO. MIN 100 Mbps MAX MIN TYP 1000 Mbps MAX MIN TYP MAX tsu(RD-RXC) Setup time, RD[3:0] valid before RXC high/low 1 1 1 tsu(RX_CTL-RXC) Setup time, RX_CTL valid before RXC high/low 1 1 1 th(RXC-RD) Hold time, RD[3:0] valid after RXC high/low 1 1 1 th(RXC-RX_CTL) Hold time, RX_CTL valid after RXC high/low 1 1 1 tt(RD) Transition time, RD 0.75 0.75 0.75 tt(RX_CTL) Transition time, RX_CTL 0.75 0.75 0.75 1 2 3 TYP UNIT ns ns ns (A) RGMII[x]_RCLK 1 1st Half-byte 2 2nd Half-byte (B) RGMII[x]_RD[3:0] (B) RGMII[x]_RCTL RGRXD[3:0] RGRXD[7:4] RXDV RXERR 3 A. B. RGMII[x]_RCLK must be externally delayed relative to the RGMII[x]_RD[3:0] and RGMII[x]_RCTL signals to meet the respective timing requirements. Data and control information is received using both edges of the clocks. RGMII[x]_RD[3:0] carries data bits 3-0 on the rising edge of RGMII[x]_RCLK and data bits 7-4 on the falling edge of RGMII[x]_RCLK. Similarly, RGMII[x]_RCTL carries RXDV on rising edge of RGMII[x]_RCLK and RXERR on falling edge of RGMII[x]_RCLK. Figure 5-9. RGMII[x]_RD[3:0], RGMII[x]_RCTL Timing - RGMII Mode 108 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-11. Switching Characteristics for RGMII[x]_TCLK - RGMII Mode (see Figure 5-10) 10 Mbps NO. 1 MIN 100 Mbps TYP MAX MIN 1000 Mbps TYP MAX MIN TYP MAX UNIT tc(TXC) Cycle time, TXC 360 440 36 44 7.2 8.8 ns 2 tw(TXCH) Pulse duration, TXC high 160 240 16 24 3.6 4.4 ns 3 tw(TXCL) Pulse duration, TXC low 160 240 16 24 3.6 4.4 ns 4 tt(TXC) Transition time, TXC 0.75 ns 0.75 0.75 1 4 2 4 3 RGMII[x]_TCLK Figure 5-10. RGMII[x]_TCLK Timing - RGMII Mode Table 5-12. Switching Characteristics for RGMII[x]_TD[3:0], and RGMII[x]_TCTL - RGMII Mode 10 Mbps NO. MIN 1 2 TYP 100 Mbps MAX MIN TYP 1000 Mbps MAX MIN TYP MAX tsk(TD-TXC) TD to TXC output skew -0.5 0.5 -0.5 0.5 -0.5 0.5 tsk(TX_CTL-TXC) TX_CTL to TXC output skew -0.5 0.5 -0.5 0.5 -0.5 0.5 tt(TD) Transition time, TD 0.75 0.75 0.75 tt(TX_CTL) Transition time, TX_CTL 0.75 0.75 0.75 UNIT ns ns (A) RGMII[x]_TCLK 1 1 2 (B) 1st Half-byte 2nd Half-byte (B) TXEN TXERR RGMII[x]_TD[3:0] RGMII[x]_TCTL A. B. The Ethernet MAC/Switch implemented in the AM335x device supports internal delay mode, but timing closure was not performed for this mode of operation. Therefore, the AM335x device does not support internal delay mode. Data and control information is transmitted using both edges of the clocks. RGMII[x]_TD[3:0] carries data bits 3-0 on the rising edge of RGMII[x]_TCLK and data bits 7-4 on the falling edge of RGMII[x]_TCLK. Similarly, RGMII[x]_TCTL carries TXEN on rising edge of RGMII[x]_TCLK and TXERR of falling edge of RGMII[x]_TCLK. Figure 5-11. RGMII[x]_TD[3:0], RGMII[x]_TCTL Timing - RGMII Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 109 PRODUCT PREVIEW (see Figure 5-11) AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.4 www.ti.com External Memory Interfaces The device includes the following external memory interfaces: • General-purpose memory controller (GPMC) • mDDR(LPDDR)/DDR2/DDR3 Memory Interface (EMIF) 5.4.1 General-Purpose Memory Controller (GPMC) NOTE For more information, see the Memory Subsystem/General-Purpose Memory Controller section of the AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). The GPMC is the unified memory controller used to interface external memory devices such as: • Asynchronous SRAM-like memories and ASIC devices • Asynchronous page mode and synchronous burst NOR flash • NAND flash 5.4.1.1 GPMC/NOR Flash—Synchronous Mode PRODUCT PREVIEW Synchronous mode is not supported for OPP50. Table 5-14 and Table 5-15 assume testing over the recommended operating conditions and electrical characteristic conditions below (see Figure 5-12 through Figure 5-16). Table 5-13. GPMC/NOR Flash Timing Conditions—Synchronous Mode TIMING CONDITION PARAMETER MIN TYP MAX UNIT Input Conditions tR Input signal rise time 1 5 ns tF Input signal fall time 1 5 ns 3 30 pF Output Condition CLOAD Output load capacitance Table 5-14. GPMC/NOR Flash Timing Requirements—Synchronous Mode NO. OPP100 PARAMETER MIN MAX UNIT F12 tsu(dV-clkH) Setup time, input data gpmc_ad[15:0] valid before output clock gpmc_clk high 3.2 ns F13 th(clkH-dV) Hold time, input data gpmc_ad[15:0] valid after output clock gpmc_clk high 2.5 ns F21 tsu(waitV-clkH) Setup time, input wait gpmc_wait[x](1) valid before output clock gpmc_clk high 3.2 ns F22 th(clkH-waitV) Hold time, input wait gpmc_wait[x](1) valid after output clock gpmc_clk high 2.5 ns (1) In gpmc_wait[x], x is equal to 0 or 1. 110 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-15. GPMC/NOR Flash Switching Characteristics—Synchronous Mode(2) PARAMETER OPP100 UNIT MIN MAX F0 1 / tc(clk) Frequency(15), output clock gpmc_clk F1 tw(clkH) Typical pulse duration, output clock gpmc_clk high 0.5P(12) 0.5P(12) ns F1 tw(clkL) Typical pulse duration, output clock gpmc_clk low 0.5P(12) 0.5P(12) ns tdc(clk) Duty cycle error, output clock gpmc_clk –500 500 ps 100 (16) tJ(clk) Jitter standard deviation 33.33 ps tR(clk) Rise time, output clock gpmc_clk 2 ns tF(clk) Fall time, output clock gpmc_clk 2 ns tR(do) Rise time, output data gpmc_ad[15:0] 2 ns tF(do) Fall time, output data gpmc_ad[15:0] 2 ns F2 td(clkH-csnV) Delay time, output clock gpmc_clk rising edge to output chip select gpmc_csn[x](11) transition F(6) – 2.2 F(6) + 4.5 ns F3 td(clkH-csnIV) Delay time, output clock gpmc_clk rising edge to output chip select gpmc_csn[x](11) invalid E(5) – 2.2 E(5) + 4.5 ns F4 td(aV-clk) Delay time, output address gpmc_a[27:1] valid to output clock gpmc_clk first edge B(2) – 4.5 B(2) + 2.3 ns F5 td(clkH-aIV) Delay time, output clock gpmc_clk rising edge to output address gpmc_a[27:1] invalid –2.3 4.5 ns F6 td(be[x]nV-clk) Delay time, output lower byte enable/command latch enable gpmc_be0n_cle, output upper byte enable gpmc_be1n valid to output clock gpmc_clk first edge B(2) – 1.9 B(2) + 2.3 ns F7 td(clkH-be[x]nIV) Delay time, output clock gpmc_clk rising edge to output lower byte enable/command latch enable gpmc_be0n_cle, output upper byte enable gpmc_be1n invalid D(4) – 2.3 D(4) + 1.9 ns F8 td(clkH-advn) Delay time, output clock gpmc_clk rising edge to output address valid/address latch enable gpmc_advn_ale transition G(7) + 2.3 G(7) + 4.5 ns F9 td(clkH-advnIV) Delay time, output clock gpmc_clk rising edge to output address valid/address latch enable gpmc_advn_ale invalid D(4) – 2.3 D(4) + 3.5 ns F10 td(clkH-oen) Delay time, output clock gpmc_clk rising edge to output enable gpmc_oen transition H(8) – 2.3 H(8) + 3.5 ns F11 td(clkH-oenIV) Delay time, output clock gpmc_clk rising edge to output enable gpmc_oen invalid E(5) – 2.3 E(5) + 3.5 ns F14 td(clkH-wen) Delay time, output clock gpmc_clk rising edge to output write enable gpmc_wen transition I(9) – 2.3 I(9) + 4.5 ns F15 td(clkH-do) Delay time, output clock gpmc_clk rising edge to output data gpmc_ad[15:0] transition J(10) – 2.3 J(10) + 1.9 ns F17 td(clkH-be[x]n) Delay time, output clock gpmc_clk rising edge to output lower byte enable/command latch enable gpmc_be0n_cle transition J(10) – 2.3 J(10) + 1.9 ns F18 tw(csnV) Pulse duration, output chip select gpmc_csn[x](11) low Read A(1) ns Write A(1) ns Pulse duration, output lower byte enable/command latch enable gpmc_be0n_cle, output upper byte enable gpmc_be1n low Read C(3) ns Write (3) ns K (13) ns K (13) ns F19 F20 tw(be[x]nV) tw(advnV) , output clock gpmc_clk MHz Pulse duration, output address valid/address latch enable gpmc_advn_ale low Read Write C PRODUCT PREVIEW NO. (1) For single read: A = (CSRdOffTime – CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst read: A = (CSRdOffTime – CSOnTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: A = (CSWrOffTime – CSOnTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) With n being the page burst access number. (2) B = ClkActivationTime * GPMC_FCLK(14) (3) For single read: C = RdCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK (14) For burst read: C = (RdCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: C = (WrCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) With n being the page burst access number. (4) For single read: D = (RdCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 111 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com For burst read: D = (RdCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: D = (WrCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) (5) For single read: E = (CSRdOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst read: E = (CSRdOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: E = (CSWrOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) (6) For csn falling edge (CS activated): – Case GpmcFCLKDivider = 0: – F = 0.5 * CSExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – F = 0.5 * CSExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and CSOnTime are odd) or (ClkActivationTime and CSOnTime are even) – F = (1 + 0.5 * CSExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – F = 0.5 * CSExtraDelay * GPMC_FCLK(14) if ((CSOnTime – ClkActivationTime) is a multiple of 3) – F = (1 + 0.5 * CSExtraDelay) * GPMC_FCLK(14) if ((CSOnTime – ClkActivationTime – 1) is a multiple of 3) – F = (2 + 0.5 * CSExtraDelay) * GPMC_FCLK(14) if ((CSOnTime – ClkActivationTime – 2) is a multiple of 3) PRODUCT PREVIEW (7) For ADV falling edge (ADV activated): – Case GpmcFCLKDivider = 0: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and ADVOnTime are odd) or (ClkActivationTime and ADVOnTime are even) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if ((ADVOnTime – ClkActivationTime) is a multiple of 3) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVOnTime – ClkActivationTime – 1) is a multiple of 3) – G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVOnTime – ClkActivationTime – 2) is a multiple of 3) For ADV rising edge (ADV deactivated) in Reading mode: – Case GpmcFCLKDivider = 0: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and ADVRdOffTime are odd) or (ClkActivationTime and ADVRdOffTime are even) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if ((ADVRdOffTime – ClkActivationTime) is a multiple of 3) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVRdOffTime – ClkActivationTime – 1) is a multiple of 3) – G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVRdOffTime – ClkActivationTime – 2) is a multiple of 3) For ADV rising edge (ADV deactivated) in Writing mode: – Case GpmcFCLKDivider = 0: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and ADVWrOffTime are odd) or (ClkActivationTime and ADVWrOffTime are even) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – G = 0.5 * ADVExtraDelay * GPMC_FCLK(14) if ((ADVWrOffTime – ClkActivationTime) is a multiple of 3) – G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVWrOffTime – ClkActivationTime – 1) is a multiple of 3) – G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK(14) if ((ADVWrOffTime – ClkActivationTime – 2) is a multiple of 3) (8) For OE falling edge (OE activated) / IO DIR rising edge (Data Bus input direction): – Case GpmcFCLKDivider = 0: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and OEOnTime are odd) or (ClkActivationTime and OEOnTime are even) – H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) if ((OEOnTime – ClkActivationTime) is a multiple of 3) – H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) if ((OEOnTime – ClkActivationTime – 1) is a multiple of 3) – H = (2 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) if ((OEOnTime – ClkActivationTime – 2) is a multiple of 3) For OE rising edge (OE deactivated): – Case GpmcFCLKDivider = 0: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and OEOffTime are odd) or (ClkActivationTime and OEOffTime are even) – H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) otherwise 112 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com – Case GpmcFCLKDivider = 2: – H = 0.5 * OEExtraDelay * GPMC_FCLK(14) if ((OEOffTime – ClkActivationTime) is a multiple of 3) – H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) if ((OEOffTime – ClkActivationTime – 1) is a multiple of 3) – H = (2 + 0.5 * OEExtraDelay) * GPMC_FCLK(14) if ((OEOffTime – ClkActivationTime – 2) is a multiple of 3) For WE rising edge (WE deactivated): – Case GpmcFCLKDivider = 0: – I = 0.5 * WEExtraDelay * GPMC_FCLK (14) – Case GpmcFCLKDivider = 1: – I = 0.5 * WEExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and WEOffTime are odd) or (ClkActivationTime and WEOffTime are even) – I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – I = 0.5 * WEExtraDelay * GPMC_FCLK(14) if ((WEOffTime – ClkActivationTime) is a multiple of 3) – I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) if ((WEOffTime – ClkActivationTime – 1) is a multiple of 3) – I = (2 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) if ((WEOffTime – ClkActivationTime – 2) is a multiple of 3) (10) J = GPMC_FCLK(14) (11) In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. (12) P = gpmc_clk period in ns (13) For read: K = (ADVRdOffTime – ADVOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For write: K = (ADVWrOffTime – ADVOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) (14) GPMC_FCLK is general-purpose memory controller internal functional clock period in ns. (15) Related to the gpmc_clk output clock maximum and minimum frequencies programmable in the GPMC module by setting the GPMC_CONFIG1_CSx configuration register bit field GpmcFCLKDivider. (16) The jitter probability density can be approximated by a Gaussian function. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 113 PRODUCT PREVIEW (9) For WE falling edge (WE activated): – Case GpmcFCLKDivider = 0: – I = 0.5 * WEExtraDelay * GPMC_FCLK(14) – Case GpmcFCLKDivider = 1: – I = 0.5 * WEExtraDelay * GPMC_FCLK(14) if (ClkActivationTime and WEOnTime are odd) or (ClkActivationTime and WEOnTime are even) – I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) otherwise – Case GpmcFCLKDivider = 2: – I = 0.5 * WEExtraDelay * GPMC_FCLK(14) if ((WEOnTime – ClkActivationTime) is a multiple of 3) – I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) if ((WEOnTime – ClkActivationTime – 1) is a multiple of 3) – I = (2 + 0.5 * WEExtraDelay) * GPMC_FCLK(14) if ((WEOnTime – ClkActivationTime – 2) is a multiple of 3) AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com F1 F0 F1 gpmc_clk F2 F3 F18 gpmc_csn[x] F4 gpmc_a[10:1] Valid Address F6 F7 F19 gpmc_be0n_cle F19 gpmc_be1n F6 F8 F8 F20 F9 gpmc_advn_ale F10 F11 PRODUCT PREVIEW gpmc_oen F13 F12 gpmc_ad[15:0] D0 gpmc_wait[x] A. B. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-12. GPMC/NOR Flash—Synchronous Single Read—(GpmcFCLKDivider = 0) 114 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com F1 F0 F1 gpmc_clk F2 F3 gpmc_csn[x] F4 Valid Address gpmc_a[10:1] F6 F7 gpmc_be0n_cle F7 gpmc_be1n F6 F8 F8 F9 gpmc_advn_ale F10 F11 gpmc_oen F13 F13 gpmc_ad[15:0] D0 F21 F12 D1 D2 D3 PRODUCT PREVIEW F12 F22 gpmc_wait[x] A. B. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-13. GPMC/NOR Flash—Synchronous Burst Read—4x16-bit (GpmcFCLKDivider = 0) Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 115 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com F1 F1 F0 gpmc_clk F2 F3 gpmc_csn[x] F4 Valid Address gpmc_a[10:1] F17 F6 F17 F17 gpmc_be0n_cle F17 F17 F17 gpmc_be1n F6 F8 F8 F9 gpmc_advn_ale F14 F14 PRODUCT PREVIEW gpmc_wen F15 gpmc_ad[15:0] D0 D1 F15 F15 D2 D3 gpmc_wait[x] A. B. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-14. GPMC/NOR Flash—Synchronous Burst Write—(GpmcFCLKDivider > 0) 116 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com F1 F0 F1 gpmc_clk F2 F3 gpmc_csn[x] F6 F7 gpmc_be0n_cle Valid F6 F7 gpmc_be1n Valid F4 gpmc_a[27:17] Address (MSB) F12 F4 gpmc_ad[15:0] F5 Address (LSB) F13 D0 F8 D1 F12 D2 F8 D3 F9 gpmc_advn_ale F10 F11 PRODUCT PREVIEW gpmc_oen gpmc_wait[x] A. B. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-15. GPMC/Multiplexed NOR Flash—Synchronous Burst Read Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 117 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com F1 F1 F0 gpmc_clk F2 F3 F18 gpmc_csn[x] F4 gpmc_a[27:17] Address (MSB) F17 F6 F17 F6 F17 F17 gpmc_be1n F17 F17 gpmc_be0n_cle F8 F8 F20 F9 gpmc_advn_ale F14 F14 PRODUCT PREVIEW gpmc_wen F15 gpmc_ad[15:0] Address (LSB) D0 F22 D1 F15 F15 D2 D3 F21 gpmc_wait[x] A. B. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-16. GPMC/Multiplexed NOR Flash—Synchronous Burst Write 118 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.1.2 GPMC/NOR Flash—Asynchronous Mode Table 5-17 and Table 5-18 assume testing over the recommended operating conditions and electrical characteristic conditions below (see Figure 5-17 through Figure 5-22). Table 5-16. GPMC/NOR Flash Timing Conditions—Asynchronous Mode TIMING CONDITION PARAMETER MIN TYP MAX UNIT Input Conditions tR Input signal rise time 1 5 ns tF Input signal fall time 1 5 ns 3 30 pF Output Condition CLOAD Output load capacitance Table 5-17. GPMC/NOR Flash Internal Timing Parameters—Asynchronous Mode(1)(2) PARAMETER FI1 Delay time, output data gpmc_ad[15:0] generation from internal functional clock GPMC_FCLK(3) FI2 Delay time, input data gpmc_ad[15:0] capture from internal functional clock GPMC_FCLK(3) FI3 OPP100 MIN OPP50 MAX MIN MAX UNIT 6.5 6.5 ns 4 4 ns Delay time, output chip select gpmc_csn[x] generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI4 Delay time, output address gpmc_a[27:1] generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI5 Delay time, output address gpmc_a[27:1] valid from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI6 Delay time, output lower-byte enable/command latch enable gpmc_be0n_cle, output upper-byte enable gpmc_be1n generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI7 Delay time, output enable gpmc_oen generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI8 Delay time, output write enable gpmc_wen generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns FI9 Skew, internal functional clock GPMC_FCLK(3) 100 100 ps PRODUCT PREVIEW NO. (1) The internal parameters table must be used to calculate data access time stored in the corresponding CS register bit field. (2) Internal parameters are referred to the GPMC functional internal clock which is not provided externally. (3) GPMC_FCLK is general-purpose memory controller internal functional clock. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 119 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-18. GPMC/NOR Flash Timing Requirements—Asynchronous Mode NO. PARAMETER OPP100 MIN FA5(1) tacc(d) OPP50 MAX FA20 tacc1-pgmode(d) FA21(3) tacc2-pgmode(d) UNIT MAX H(5) H(5) ns Page mode successive data access time P (4) P(4) ns Page mode first data access time H(5) H(5) ns Data access time (2) MIN (1) The FA5 parameter illustrates the amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA5 functional clock cycles, input data is internally sampled by active functional clock edge. FA5 value must be stored inside the AccessTime register bit field. (2) The FA20 parameter illustrates amount of time required to internally sample successive input page data. It is expressed in number of GPMC functional clock cycles. After each access to input page data, next input page data is internally sampled by active functional clock edge after FA20 functional clock cycles. The FA20 value must be stored in the PageBurstAccessTime register bit field. (3) The FA21 parameter illustrates amount of time required to internally sample first input page data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA21 functional clock cycles, first input page data is internally sampled by active functional clock edge. FA21 value must be stored inside the AccessTime register bit field. (4) P = PageBurstAccessTime * (TimeParaGranularity + 1) * GPMC_FCLK(6) (5) H = AccessTime * (TimeParaGranularity + 1) * GPMC_FCLK(6) (6) GPMC_FCLK is general-purpose memory controller internal functional clock period in ns. Table 5-19. GPMC/NOR Flash Switching Characteristics—Asynchronous Mode PRODUCT PREVIEW NO. FA0 FA1 FA3 OPP100 PARAMETER MIN OPP50 MAX MIN tR(d) Rise time, output data gpmc_ad[15:0] tF(d) Fall time, output data gpmc_ad[15:0] tw(be[x]nV) Pulse duration, output lower-byte enable/command latch enable gpmc_be0n_cle, output upper-byte enable gpmc_be1n valid time Read Write N(12) N(12) Pulse duration, output chip select gpmc_csn[x](13) low Read A(1) A(1) Write (1) A(1) Delay time, output chip select gpmc_csn[x](13) valid to output address valid/address latch enable gpmc_advn_ale invalid Read tw(csnV) td(csnV-advnIV) 2 MAX Write 2 ns 2 2 ns N(12) N(12) ns A B(2) – 0.2 B (2) – 0.2 B(2) + 2.0 B (2) UNIT B(2) – 0.2 + 2.0 B (2) B(2) + 2.0 – 0.2 B(2) + 2.0 ns ns FA4 td(csnV-oenIV) Delay time, output chip select gpmc_csn[x](13) valid to output enable gpmc_oen invalid (Single read) C(3) – 0.2 C(3) + 2.0 C(3) – 0.2 C(3) + 2.0 ns FA9 td(aV-csnV) Delay time, output address gpmc_a[27:1] valid to output chip select gpmc_csn[x](13) valid J(9) – 0.2 J(9) + 2.0 J(9) – 0.2 J(9) + 2.0 ns FA10 td(be[x]nV-csnV) Delay time, output lower-byte enable/command latch enable gpmc_be0n_cle, output upper-byte enable gpmc_be1n valid to output chip select gpmc_csn[x](13) valid J(9) – 0.2 J(9) + 2.0 J(9) – 0.2 J(9) + 2.0 ns FA12 td(csnV-advnV) Delay time, output chip select gpmc_csn[x](13) valid to output address valid/address latch enable gpmc_advn_ale valid K(10) – 0.2 K(10) + 2.0 K(10) – 0.2 K(10) + 2.0 ns FA13 td(csnV-oenV) Delay time, output chip select gpmc_csn[x](13) valid to output enable gpmc_oen valid L(11) – 0.2 L(11) + 2.0 L L(11) + 2.0 ns FA16 tw(aIV) Pulse durationm output address gpmc_a[26:1] invalid between 2 successive R/W accesses G(7) FA18 td(csnV-oenIV) Delay time, output chip select gpmc_csn[x](13) valid to output enable gpmc_oen invalid (Burst read) I(8) – 0.2 FA20 tw(aV) Pulse duration, output address gpmc_a[27:1] valid – 2nd, 3rd, and 4th accesses FA25 td(csnV-wenV) Delay time, output chip select gpmc_csn[x](13) valid to output write enable gpmc_wen valid 120 Peripheral Information and Timings (11) G(7) I(8) + 2.0 I(8) – 0.2 D(4) E(5) – 0.2 – 0.2 ns I(8) + 2.0 D(4) E(5) + 2.0 E(5) – 0.2 ns ns E(5) + 2.0 ns Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-19. GPMC/NOR Flash Switching Characteristics—Asynchronous Mode (continued) NO. PARAMETER FA27 td(csnV-wenIV) Delay time, output chip select gpmc_csn[x](13) valid to output write enable gpmc_wen invalid FA28 td(wenV-dV) Delay time, output write enable gpmc_ wen valid to output data gpmc_ad[15:0] valid FA29 td(dV-csnV) Delay time, output data gpmc_ad[15:0] valid to output chip select gpmc_csn[x](13) valid FA37 td(oenV-aIV) Delay time, output enable gpmc_oen valid to output address gpmc_ad[15:0] phase end OPP100 OPP50 UNIT MIN MAX MIN MAX F(6) – 0.2 F(6) + 2.0 F(6) – 0.2 F(6) + 2.0 ns 2.0 ns J(9) + 2.0 ns 2.0 ns 2.0 J(9) – 0.2 J(9) + 2.0 J(9) – 0.2 2.0 (1) For single read: A = (CSRdOffTime – CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For single write: A = (CSWrOffTime – CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst read: A = (CSRdOffTime – CSOnTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: A = (CSWrOffTime – CSOnTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) with n being the page burst access number (2) For reading: B = ((ADVRdOffTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) For writing: B = ((ADVWrOffTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (4) D = PageBurstAccessTime * (TimeParaGranularity + 1) * GPMC_FCLK(14) (5) E = ((WEOnTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (6) F = ((WEOffTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (7) G = Cycle2CycleDelay * GPMC_FCLK(14) (8) I = ((OEOffTime + (n – 1) * PageBurstAccessTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (9) J = (CSOnTime * (TimeParaGranularity + 1) + 0.5 * CSExtraDelay) * GPMC_FCLK(14) (10) K = ((ADVOnTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (11) L = ((OEOnTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (12) For single read: N = RdCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK(14) For single write: N = WrCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst read: N = (RdCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) For burst write: N = (WrCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) (13) In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. (14) GPMC_FCLK is general-purpose memory controller internal functional clock period in ns. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 121 PRODUCT PREVIEW (3) C = ((OEOffTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK gpmc_clk FA5 FA1 gpmc_csn[x] FA9 gpmc_a[10:1] Valid Address FA0 FA10 gpmc_be0n_cle Valid FA0 gpmc_be1n Valid FA10 FA3 FA12 gpmc_advn_ale FA4 PRODUCT PREVIEW FA13 gpmc_oen Data IN 0 gpmc_ad[15:0] Data IN 0 gpmc_wait[x] A. B. C. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. FA5 parameter illustrates amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA5 functional clock cycles, input data will be internally sampled by active functional clock edge. FA5 value must be stored inside AccessTime register bits field. GPMC_FCLK is an internal clock (GPMC functional clock) not provided externally. Figure 5-17. GPMC/NOR Flash—Asynchronous Read—Single Word 122 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK gpmc_clk FA5 FA5 FA1 FA1 gpmc_csn[x] FA16 FA9 FA9 gpmc_a[10:1] Address 0 Address 1 FA0 FA10 FA0 FA10 gpmc_be0n_cle Valid Valid FA0 gpmc_be1n FA0 Valid FA10 Valid FA10 FA3 FA3 FA12 FA12 gpmc_advn_ale FA4 PRODUCT PREVIEW FA4 FA13 FA13 gpmc_oen gpmc_ad[15:0] Data Upper gpmc_wait[x] A. B. C. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. FA5 parameter illustrates amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA5 functional clock cycles, input data will be internally sampled by active functional clock edge. FA5 value must be stored inside AccessTime register bits field. GPMC_FCLK is an internal clock (GPMC functional clock) not provided externally. Figure 5-18. GPMC/NOR Flash—Asynchronous Read—32-bit Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 123 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK gpmc_clk FA21 FA20 FA20 FA20 Add1 Add2 Add3 D0 D1 D2 FA1 gpmc_csn[x] FA9 Add0 gpmc_a[10:1] Add4 FA0 FA10 gpmc_be0n_cle FA0 FA10 gpmc_be1n FA12 gpmc_advn_ale FA18 PRODUCT PREVIEW FA13 gpmc_oen gpmc_ad[15:0] D3 D3 gpmc_wait[x] A. B. C. D. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. FA21 parameter illustrates amount of time required to internally sample first input page data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA21 functional clock cycles, first input page data will be internally sampled by active functional clock edge. FA21 calculation must be stored inside AccessTime register bits field. FA20 parameter illustrates amount of time required to internally sample successive input page data. It is expressed in number of GPMC functional clock cycles. After each access to input page data, next input page data will be internally sampled by active functional clock edge after FA20 functional clock cycles. FA20 is also the duration of address phases for successive input page data (excluding first input page data). FA20 value must be stored in PageBurstAccessTime register bits field. GPMC_FCLK is an internal clock (GPMC functional clock) not provided externally. Figure 5-19. GPMC/NOR Flash—Asynchronous Read—Page Mode 4x16-bit 124 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com gpmc_fclk gpmc_clk FA1 gpmc_csn[x] FA9 gpmc_a[10:1] Valid Address FA0 FA10 gpmc_be0n_cle FA0 FA10 gpmc_be1n FA3 FA12 gpmc_advn_ale FA27 FA25 PRODUCT PREVIEW gpmc_wen FA29 gpmc_ad[15:0] Data OUT gpmc_wait[x] A. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-20. GPMC/NOR Flash—Asynchronous Write—Single Word Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 125 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK gpmc_clk FA1 FA5 gpmc_csn[x] FA9 gpmc_a[27:17] Address (MSB) FA0 FA10 gpmc_be0n_cle Valid FA0 FA10 gpmc_be1n Valid FA3 FA12 gpmc_advn_ale FA4 PRODUCT PREVIEW FA13 gpmc_oen FA29 gpmc_ad[15:0] FA37 Data IN Address (LSB) Data IN gpmc_wait[x] A. B. C. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. FA5 parameter illustrates amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after FA5 functional clock cycles, input data will be internally sampled by active functional clock edge. FA5 value must be stored inside AccessTime register bits field. GPMC_FCLK is an internal clock (GPMC functional clock) not provided externally. Figure 5-21. GPMC / Multiplexed NOR Flash—Asynchronous Read—Single Word 126 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com gpmc_fclk gpmc_clk FA1 gpmc_csn[x] FA9 gpmc_a[27:17] Address (MSB) FA0 FA10 gpmc_be0n_cle FA0 FA10 gpmc_be1n FA3 FA12 gpmc_advn_ale FA27 FA25 FA29 gpmc_ad[15:0] PRODUCT PREVIEW gpmc_wen FA28 Valid Address (LSB) Data OUT gpmc_wait[x] A. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. Figure 5-22. GPMC/Multiplexed NOR Flash—Asynchronous Write—Single Word Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 127 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.4.1.3 www.ti.com GPMC/NAND Flash—Asynchronous Mode Table 5-21 and Table 5-22 assume testing over the recommended operating conditions and electrical characteristic conditions below (see Figure 5-23 through Figure 5-26). Table 5-20. GPMC/NAND Flash Timing Conditions—Asynchronous Mode TIMING CONDITION PARAMETER MIN TYP MAX UNIT Input Conditions tR Input signal rise time 1 5 ns tF Input signal fall time 1 5 ns 3 30 pF Output Condition CLOAD Output load capacitance Table 5-21. GPMC/NAND Flash Internal Timing Parameters—Asynchronous Mode(1)(2) NO. PARAMETER OPP100 MIN OPP50 MAX MIN MAX UNIT PRODUCT PREVIEW GNFI1 Delay time, output data gpmc_ad[15:0] generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI2 Delay time, input data gpmc_ad[15:0] capture from internal functional clock GPMC_FCLK(3) 4.0 4.0 ns GNFI3 Delay time, output chip select gpmc_csn[x] generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI4 Delay time, output address valid/address latch enable gpmc_advn_ale generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI5 Delay time, output lower-byte enable/command latch enable gpmc_be0n_cle generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI6 Delay time, output enable gpmc_oen generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI7 Delay time, output write enable gpmc_wen generation from internal functional clock GPMC_FCLK(3) 6.5 6.5 ns GNFI8 Skew, functional clock GPMC_FCLK(3) 100 100 ps (1) Internal parameters table must be used to calculate data access time stored in the corresponding CS register bit field. (2) Internal parameters are referred to the GPMC functional internal clock which is not provided externally. (3) GPMC_FCLK is general-purpose memory controller internal functional clock. Table 5-22. GPMC/NAND Flash Timing Requirements—Asynchronous Mode NO. GNF12(1) OPP100 PARAMETER tacc(d) MIN OPP50 MAX J(2) Access time, input data gpmc_ad[15:0] MIN MAX J(2) UNIT ns (1) The GNF12 parameter illustrates the amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of the read cycle and after GNF12 functional clock cycles, input data is internally sampled by the active functional clock edge. The GNF12 value must be stored inside AccessTime register bit field. (2) J = AccessTime * (TimeParaGranularity + 1) * GPMC_FCLK(3) (3) GPMC_FCLK is general-purpose memory controller internal functional clock period in ns. 128 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-23. GPMC/NAND Flash Switching Characteristics—Asynchronous Mode OPP100 PARAMETER MIN OPP50 MAX MIN MAX UNIT tR(d) Rise time, output data gpmc_ad[15:0] 2 2 ns tF(d) Fall time, output data gpmc_ad[15:0] 2 2 ns GNF0 tw(wenV) Pulse duration, output write enable gpmc_wen valid A(1) GNF1 td(csnV-wenV) Delay time, output chip select gpmc_csn[x](13) valid to output write enable gpmc_wen valid B(2) – 0.2 B(2) + 2.0 B(2) – 0.2 B(2) + 2.0 ns GNF2 tw(cleH-wenV) Delay time, output lower-byte enable/command latch enable gpmc_be0n_cle high to output write enable gpmc_wen valid C(3) – 0.2 C(3) + 2.0 C(3) – 0.2 C(3) + 2.0 ns GNF3 tw(wenV-dV) Delay time, output data gpmc_ad[15:0] valid to output write enable gpmc_wen valid D(4) – 0.2 D(4) + 2.0 D(4) – 0.2 D(4) + 2.0 ns GNF4 tw(wenIV-dIV) Delay time, output write enable gpmc_wen invalid to output data gpmc_ad[15:0] invalid E(5) – 0.2 E(5) + 2.0 E(5) – 0.2 E(5) + 2.0 ns GNF5 tw(wenIV-cleIV) Delay time, output write enable gpmc_wen invalid to output lower-byte enable/command latch enable gpmc_be0n_cle invalid F(6) – 0.2 F(6) + 2.0 F(6) – 0.2 F(6) + 2.0 ns GNF6 tw(wenIV-csnIV) Delay time, output write enable gpmc_wen invalid to output chip select gpmc_csn[x](13) invalid G(7) – 0.2 G(7) + 2.0 G(7) – 0.2 G(7) + 2.0 ns GNF7 tw(aleH-wenV) Delay time, output address valid/address latch enable gpmc_advn_ale high to output write enable gpmc_wen valid C(3) – 0.2 C(3) + 2.0 C(3) – 0.2 C(3) + 2.0 ns GNF8 tw(wenIV-aleIV) Delay time, output write enable gpmc_wen invalid to output address valid/address latch enable gpmc_advn_ale invalid F(6) – 0.2 F(6) + 2.0 F(6) – 0.2 F(6) + 2.0 ns GNF9 tc(wen) Cycle time, write H(8) ns + 2.0 ns K(10) ns ns H(8) (13) GNF10 td(csnV-oenV) Delay time, output chip select gpmc_csn[x] valid to output enable gpmc_oen valid GNF13 tw(oenV) Pulse duration, output enable gpmc_oen valid GNF14 tc(oen) Cycle time, read GNF15 tw(oenIV-csnIV) A(1) Delay time, output enable gpmc_oen invalid to output chip select gpmc_csn[x](13) invalid (9) I (9) – 0.2 I (9) + 2.0 I (9) – 0.2 I K(10) L(11) (12) M L(11) (12) – 0.2 M (12) + 2.0 M PRODUCT PREVIEW NO. ns (12) – 0.2 M + 2.0 ns (1) A = (WEOffTime – WEOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK(14) (2) B = ((WEOnTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (3) C = ((WEOnTime – ADVOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay – ADVExtraDelay)) * GPMC_FCLK(14) (4) D = (WEOnTime * (TimeParaGranularity + 1) + 0.5 * WEExtraDelay) * GPMC_FCLK(14) (5) E = ((WrCycleTime – WEOffTime) * (TimeParaGranularity + 1) – 0.5 * WEExtraDelay) * GPMC_FCLK(14) (6) F = ((ADVWrOffTime – WEOffTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay – WEExtraDelay)) * GPMC_FCLK(14) (7) G = ((CSWrOffTime – WEOffTime) * (TimeParaGranularity + 1) + 0.5 * (CSExtraDelay – WEExtraDelay)) * GPMC_FCLK(14) (8) H = WrCycleTime * (1 + TimeParaGranularity) * GPMC_FCLK(14) (9) I = ((OEOnTime – CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay – CSExtraDelay)) * GPMC_FCLK(14) (10) K = (OEOffTime – OEOnTime) * (1 + TimeParaGranularity) * GPMC_FCLK(14) (11) L = RdCycleTime * (1 + TimeParaGranularity) * GPMC_FCLK(14) (12) M = ((CSRdOffTime – OEOffTime) * (TimeParaGranularity + 1) + 0.5 * (CSExtraDelay – OEExtraDelay)) * GPMC_FCLK(14) (13) In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. (14) GPMC_FCLK is general-purpose memory controller internal functional clock period in ns. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 129 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK GNF1 GNF6 GNF2 GNF5 gpmc_csn[x] gpmc_be0n_cle gpmc_advn_ale gpmc_oen GNF0 gpmc_wen GNF3 GNF4 gpmc_ad[15:0] (1) Command In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. Figure 5-23. GPMC/NAND Flash—Command Latch Cycle GPMC_FCLK PRODUCT PREVIEW GNF1 GNF6 GNF7 GNF8 gpmc_csn[x] gpmc_be0n_cle gpmc_advn_ale gpmc_oen GNF9 GNF0 gpmc_wen GNF3 gpmc_ad[15:0] (1) GNF4 Address In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. Figure 5-24. GPMC/NAND Flash—Address Latch Cycle 130 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com GPMC_FCLK GNF12 GNF10 GNF15 gpmc_csn[x] gpmc_be0n_cle gpmc_advn_ale GNF14 GNF13 gpmc_oen gpmc_ad[15:0] DATA gpmc_wait[x] (1) (2) (3) GNF12 parameter illustrates amount of time required to internally sample input data. It is expressed in number of GPMC functional clock cycles. From start of read cycle and after GNF12 functional clock cycles, input data will be internally sampled by active functional clock edge. GNF12 value must be stored inside AccessTime register bits field. GPMC_FCLK is an internal clock (GPMC functional clock) not provided externally. In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. In gpmc_wait[x], x is equal to 0 or 1. PRODUCT PREVIEW Figure 5-25. GPMC/NAND Flash—Data Read Cycle GPMC_FCLK GNF1 GNF6 gpmc_csn[x] gpmc_be0n_cle gpmc_advn_ale gpmc_oen GNF9 GNF0 gpmc_wen GNF3 gpmc_ad[15:0] (1) GNF4 DATA In gpmc_csn[x], x is equal to 0, 1, 2, 3, 4 or 5. Figure 5-26. GPMC / NAND Flash—Data Write Cycle Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 131 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.4.2 www.ti.com mDDR(LPDDR)/DDR2/DDR3 Memory Interface The device has a dedicated interface to mDDR(LPDDR), DDR2, and DDR3 SDRAM. It supports JEDEC standard compliant mDDR(LPDDR), DDR2, and DDR3 SDRAM devices with a 16-bit data path to external SDRAM memory. For more details on the mDDR(LPDDR)/DDR2/DDR3 memory interface, see the EMIF chapter of the AM335x Sitara ARM Cortex A-8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). 5.4.2.1 mDDR(LPDDR) Routing Guidelines It is common to find industry references to mobile double data rate (mDDR) when discussing JEDEC defined low-power double-data rate (LPDDR) memory devices. The following guidelines use LPDDR when referencing JEDEC defined low-power double-data rate memory devices. 5.4.2.1.1 Board Designs TI only supports board designs that follow the guidelines outlined in this document. The switching characteristics and the timing diagram for the LPDDR memory interface are shown in Table 5-24 and Figure 5-27. PRODUCT PREVIEW Table 5-24. Switching Characteristics Over Recommended Operating Conditions for LPDDR Memory Interface NO. 1 (1) PARAMETER MIN MAX tc(DDR_CK/DDR_CKn) Cycle time, DDR_CK/DDR_CKn 5 (1) UNIT ns The JEDEC JESD209B specification only defines the maximum clock period for LPDDR333 and faster speed bin LPDDR memory devices. To determine the maximum clock period, see the respective LPDDR memory data sheet. 1 DDR_CK DDR_CKn Figure 5-27. LPDDR Memory Interface Clock Timing 5.4.2.1.2 LPDDR Interface This section provides the timing specification for the LPDDR interface as a PCB design and manufacturing specification. The design rules constrain PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. These rules, when followed, result in a reliable LPDDR memory system without the need for a complex timing closure process. For more information regarding the guidelines for using this LPDDR specification, see the Understanding TI’s PCB Routing Rule-Based DDR Timing Specification application report (literature number SPRAAV0). This application report provides generic guidelines and approach. All the specifications provided in the data manual take precedence over the generic guidelines and must be adhered to for a reliable LPDDR interface operation. 5.4.2.1.2.1 LPDDR Interface Schematic Figure 5-28 shows the schematic connections for 16-bit interface on AM335x device using one x16 LPDDR device. The AM335x LPDDR memory interface only supports 16-bit wide mode of operation. The AM335x device can only source one load connected to the DQS[x] and DQ[x] net class signals and one load connected to the CK and ADDR_CTRL net class signals. For more information related to net classes, see Section 5.4.2.1.2.8. 132 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 16-Bit LPDDR Device AM335x DDR_D0 DQ0 DDR_D7 DDR_DQM0 DDR_DQS0 NC (A) DQ8 DDR_D15 DDR_DQM1 DDR_DQS1 DDR_DQSn1 NC DDR_ODT NC DDR_BA0 DDR_BA1 DDR_BA2 T T NC BA0 BA1 DDR_A0 T A0 DDR_A15 DDR_CSn0 T T A15 CS DDR_CASn DDR_RASn DDR_WEn DDR_CKE DDR_CK T T T T T T CAS DDR_CKn DQ15 UDM UDQS (A) PRODUCT PREVIEW DDR_DQSn0 DDR_D8 DQ7 LDM LDQS RAS WE CKE CK CK DDR_VREF NC DDR_RESETn NC DDR_VTP 49.9 Ω (±1%, 20 mW) A. B. Enable internal weak pulldown on these pins. For details, see the EMIF chapter of the AM335x Sitara ARM Cortex A-8 Microprocessors (MPUs) Technical Reference Manual (literature number SPRUH73). For all the termination requirements, see Section 5.4.2.1.2.9. Figure 5-28. 16-Bit LPDDR Interface Using One 16-Bit LPDDR Device Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 133 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.2.2 Compatible JEDEC LPDDR Devices Table 5-25 shows the parameters of the JEDEC LPDDR devices that are compatible with this interface. Generally, the LPDDR interface is compatible with x16 LPDDR400 speed grade LPDDR devices. Table 5-25. Compatible JEDEC LPDDR Devices (Per Interface)(1) NO. PARAMETER 1 JEDEC LPDDR device speed grade 2 JEDEC LPDDR device bit width 3 JEDEC LPDDR device count 4 JEDEC LPDDR device terminal count MIN MAX UNIT LPDDR400 x16 x16 Bits 1 Devices 60 Terminals (1) If the LPDDR interface is operated with a clock frequency less than 200 MHz, lower-speed grade LPDDR devices may be used if the minimum clock period specified for the LPDDR device is less than or equal to the minimum clock period selected for the AM335x LPDDR interface. 5.4.2.1.2.3 PCB Stackup The minimum stackup required for routing the AM335x device is a four-layer stackup as shown in Table 5-26. Additional layers may be added to the PCB stackup to accommodate other circuitry, enhance signal integrity and electromagnetic interference performance, or to reduce the size of the PCB footprint. PRODUCT PREVIEW Table 5-26. Minimum PCB Stackup (1) (1) 134 LAYER TYPE DESCRIPTION 1 Signal Top signal routing 2 Plane Ground 3 Plane Split Power Plane 4 Signal Bottom signal routing All signals that have critical signal integrity requirements should be routed first on layer 1. It may not be possible to route all of these signals on layer 1 which requires some to be routed on layer 4. When this is done, the signal routes on layer 4 should not cross splits in the power plane. Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Complete stackup specifications are provided in Table 5-27. Table 5-27. PCB Stackup Specifications(1) PARAMETER MIN TYP 1 PCB routing/plane layers 4 2 Signal routing layers 2 3 Full ground layers under LPDDR routing region 1 4 Number of ground plane cuts allowed within LPDDR routing region 5 Full VDDS_DDR power reference layers under LPDDR routing region 6 Number of layers between LPDDR routing layer and reference ground plane 7 PCB routing feature size 4 8 PCB trace width, w 4 9 PCB BGA escape via pad size(2) 10 0 0 18 PCB BGA escape via hole size AM335x BGA pad size 13 Single-ended impedance, Zo(3) 14 Impedance control(4)(5) UNIT 1 (2) 11 MAX mils mils 20 mils 10 ZCZ package 0.5 ZCE package 0.4 50 Zo-5 Zo mils mm 75 ohms Zo+5 ohms (1) For the LPDDR device BGA pad size, see the LPDDR device manufacturer documentation. (2) A 20/10 via may be used if enough power routing resources are available. An 18/10 via allows for more flexible power routing to the AM335x device. (3) Zo is the nominal singled-ended impedance selected for the PCB. (4) This parameter specifies the AC characteristic impedance tolerance for each segment of a PCB signal trace relative to the chosen Zo defined by the single-ended impedance parameter. (5) Tighter impedance control is required to ensure flight time skew is minimal. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 135 PRODUCT PREVIEW NO. AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.2.4 Placement Figure 5-29 shows the required placement for the LPDDR devices. The dimensions for this figure are defined in Table 5-28. The placement does not restrict the side of the PCB on which the devices are mounted. The ultimate purpose of the placement is to limit the maximum trace lengths and allow for proper routing space. For single-memory LPDDR systems, the second LPDDR device is omitted from the placement. X Y OFFSET LPDDR Device Y Y OFFSET LPDDR Interface A1 AM335x A1 PRODUCT PREVIEW Recommended LPDDR Device Orientation Figure 5-29. AM335x Device and LPDDR Device Placement Table 5-28. Placement Specifications(1) NO. MAX UNIT 1 X(2)(3) PARAMETER MIN 1750 mils 2 Y(2)(3) 1280 mils 650 mils (2)(3)(4) 3 Y Offset 4 Clearance from non-LPDDR signal to LPDDR keepout region(5)(6) 4 w (1) LPDDR keepout region to encompass entire LPDDR routing area. (2) For dimension definitions, see Figure 5-29. (3) Measurements from center of AM335x device to center of LPDDR device. (4) For single-memory systems, it is recommended that Y offset be as small as possible. (5) w is defined as the signal trace width. (6) Non-LPDDR signals allowed within LPDDR keepout region provided they are separated from LPDDR routing layers by a ground plane. 136 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.2.5 LPDDR Keepout Region The region of the PCB used for the LPDDR circuitry must be isolated from other signals. The LPDDR keepout region is defined for this purpose and is shown in Figure 5-30. This region should encompass all LPDDR circuitry and the region size varies with component placement and LPDDR routing. Additional clearances required for the keepout region are shown in Table 5-28. Non-LPDDR signals should not be routed on the same signal layer as LPDDR signals within the LPDDR keepout region. Non-LPDDR signals may be routed in the region provided they are routed on layers separated from LPDDR signal layers by a ground layer. No breaks should be allowed in the reference ground or VDDS_DDR power plane in this region. In addition, the VDDS_DDR power plane should cover the entire keepout region. LPDDR Device LPDDR Interface A1 Figure 5-30. LPDDR Keepout Region 5.4.2.1.2.6 Bulk Bypass Capacitors Bulk bypass capacitors are required for moderate speed bypassing of the LPDDR and other circuitry. Table 5-29 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note that this table only covers the bypass needs of the AM335x LPDDR interface and LPDDR device(s). Additional bulk bypass capacitance may be needed for other circuitry. Table 5-29. Bulk Bypass Capacitors(1) NO. PARAMETER 1 AM335x VDDS_DDR bulk bypass capacitor count 2 AM335x VDDS_DDR bulk bypass total capacitance 3 LPDDR#1 bulk bypass capacitor count 4 LPDDR#1 bulk bypass total capacitance 5 LPDDR#2 bulk bypass capacitor count (2) 6 LPDDR#2 bulk bypass total capacitance(2) MIN 1 MAX UNIT Devices 10 μF 1 Devices 10 μF 1 Devices 10 μF (1) These devices should be placed near the device they are bypassing, but preference should be given to the placement of the high-speed (HS) bypass capacitors. (2) Only used when two LPDDR devices are used. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 137 PRODUCT PREVIEW A1 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.2.7 High-Speed Bypass Capacitors High-speed (HS) bypass capacitors are critical for proper LPDDR interface operation. It is particularly important to minimize the parasitic series inductance of the HS bypass capacitors, AM335x/LPDDR power, and AM335x/LPDDR ground connections. Table 5-30 contains the specification for the HS bypass capacitors as well as for the power connections on the PCB. Table 5-30. High-Speed Bypass Capacitors NO. PARAMETER MIN PRODUCT PREVIEW 1 HS bypass capacitor package size(1) 2 Distance from HS bypass capacitor to device being bypassed 3 Number of connection vias for each HS bypass capacitor(2) 4 Trace length from bypass capacitor contact to connection via 5 Number of connection vias for each AM335x VDDS_DDR/VSS terminal 6 Trace length from AM335x VDDS_DDR/VSS terminal to connection via 7 Number of connection vias for each LPDDR device power/ground terminal 8 Trace length from LPDDR device power/ground terminal to connection via 9 AM335x VDDS_DDR HS bypass capacitor count(3) 10 10 AM335x VDDS_DDR HS bypass capacitor total capacitance 0.6 11 LPDDR device HS bypass capacitor count(3)(4) 12 LPDDR device HS bypass capacitor total capacitance(4) MAX UNIT 0402 10 mils 250 2 mils Vias 30 1 mils Vias 35 1 mils Vias 35 8 0.4 mils Devices μF Devices μF (1) LxW, 10-mil units; i.e., a 0402 is a 40x20-mil surface-mount capacitor. (2) An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board. (3) These devices should be placed as close as possible to the device being bypassed. (4) Per LPDDR device. 5.4.2.1.2.8 Net Classes Table 5-31 lists the clock net classes for the LPDDR interface. Table 5-32 lists the signal net classes, and associated clock net classes, for the signals in the LPDDR interface. These net classes are used for the termination and routing rules that follow. Table 5-31. Clock Net Class Definitions CLOCK NET CLASS AM335x PIN NAMES CK DDR_CK/DDR_CKn DQS0 DDR_DQS0 DQS1 DDR_DQS1 Table 5-32. Signal Net Class Definitions 138 SIGNAL NET CLASS ASSOCIATED CLOCK NET CLASS ADDR_CTRL CK DQ0 DQS0 DDR_D[7:0], DDR_DQM0 DQ1 DQS1 DDR_D[15:8], DDR_DQM1 Peripheral Information and Timings AM335x PIN NAMES DDR_BA[1:0], DDR_A[15:0], DDR_CSn0, DDR_CASn, DDR_RASn, DDR_WEn, DDR_CKE Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.2.9 LPDDR Signal Termination There is no specific need for adding terminations on the LPDDR interface. However, system designers may evaluate the need for serial terminators for EMI and overshoot reduction. Placement of serial terminations for DQS[x] and DQ[x] net class signals should be determined based on PCB analysis. Placement of serial terminations for ADDR_CTRL net class signals should be close to the AM335x device. Table 5-33 shows the specifications for the serial terminators in such cases. Table 5-33. LPDDR Signal Terminations No. Min Typ Max Unit 1 Parameter CK net class(1) 0 22 Zo(2) ohms 2 ADDR_CTRL net class(1)(3)(4) 0 22 Zo(2) ohms 3 DQS0, DQS1, DQ0, and DQ1 net classes 0 22 Zo(2) ohms (1) Only series termination is permitted. (2) Zo is the LPDDR PCB trace characteristic impedance. (3) Series termination values larger than typical only recommended to address EMI issues. PRODUCT PREVIEW (4) Series termination values should be uniform across net class. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 139 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.1.3 LPDDR CK and ADDR_CTRL Routing Figure 5-31 shows the topology of the routing for the CK and ADDR_CTRL net classes. The length of signal path AB and AC should be minimized with emphasis to minimize lengths C and D such that length A is the majority of the total length of signal path AB and AC. C A LPDDR Interface B A1 AM335x A1 Figure 5-31. CK and ADDR_CTRL Routing and Topology PRODUCT PREVIEW Table 5-34. CK and ADDR_CTRL Routing Specification(1)(2) NO. PARAMETER MIN TYP MAX UNIT 1 Center-to-center CK spacing 2w 2 CK differential pair skew length mismatch(2)(3) 25 mils 3 CK B-to-CK C skew length mismatch 25 mils 4 Center-to-center CK to other LPDDR trace spacing(4) 5 CK/ADDR_CTRL nominal trace length(5) CACLM+50 mils 6 ADDR_CTRL-to-CK skew length mismatch 100 mils 7 ADDR_CTRL-to-ADDR_CTRL skew length mismatch 100 mils 8 Center-to-center ADDR_CTRL to other LPDDR trace spacing(4) 4w 3w 4w CACLM-50 CACLM 9 Center-to-center ADDR_CTRL to other ADDR_CTRL trace spacing(4) 10 ADDR_CTRL A-to-B/ADDR_CTRL A-to-C skew length mismatch(2) 100 mils 11 ADDR_CTRL B-to-C skew length mismatch 100 mils (1) CK represents the clock net class, and ADDR_CTRL represents the address and control signal net class. (2) Series terminator, if used, should be located closest to the AM335x device. (3) Differential impedance should be Zo x 2, where Zo is the single-ended impedance defined in Table 5-27. (4) Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. (5) CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes. 140 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com A1 DQ[0] DQ[1] LPDDR Interface Figure 5-32 shows the topology and routing for the DQS[x] and DQ[x] net classes; the routes are point to point. Skew matching across bytes is not needed nor recommended. AM335x Figure 5-32. DQS[x] and DQ[x] Routing and Topology Table 5-35. DQS[x] and DQ[x] Routing Specification(1) PARAMETER 1 Center-to-center DQS[x] spacing 2 Center-to-center DDR_DQS[x] to other LPDDR trace spacing(2) 3 DQS[x]/DQ[x] nominal trace length(3) 4 DQ[x]-to-DQS[x] skew length mismatch(3) MIN TYP MAX UNIT 2w 4w DQLM-50 DQLM DQLM+50 mils 100 mils 100 mils (3) 5 DQ[x]-to-DQ[x] skew length mismatch 6 Center-to-center DQ[x] to other LPDDR trace spacing(2)(4) 4w 7 Center-to-center DQ[x] to other DQ[x] trace spacing(2)(5) 3w (1) DQS[x] represents the DQS0 and DQS1 clock net classes, and DQ[x] represents the DQ0 and DQ1 signal net classes. (2) Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. (3) There is no requirement, and it is not recommended, to skew match between data bytes; i.e., from net classes DQS0 and DQ0 to net classes DQS1 and DQ1. (4) Signals from one DQ net class should be considered other LPDDR traces to another DQ net class. (5) DQLM is the longest Manhattan distance of each of the DQS[x] and DQ[x] net classes. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 141 PRODUCT PREVIEW NO. AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.4.2.2 www.ti.com DDR2 Routing Guidelines 5.4.2.2.1 Board Designs TI only supports board designs that follow the guidelines outlined in this document. The switching characteristics and the timing diagram for the DDR2 memory interface are shown in Table 5-36 and Figure 5-33. Table 5-36. Switching Characteristics Over Recommended Operating Conditions for DDR2 Memory Interface NO. 1 (1) PARAMETER MIN MAX tc(DDR_CK/DDR_CKn) Cycle time, DDR_CK/DDR_CKn 3.75 8 (1) UNIT ns The JEDEC JESD79-2F specification defines the maximum clock period of 8 ns for all standard-speed bin DDR2 memory devices. Therefore, all standard-speed bin DDR2 memory devices are required to operate at 125 MHz. 1 DDR_CK PRODUCT PREVIEW DDR_CKn Figure 5-33. DDR2 Memory Interface Clock Timing 5.4.2.2.2 DDR2 Interface This section provides the timing specification for the DDR2 interface as a PCB design and manufacturing specification. The design rules constrain PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. These rules, when followed, result in a reliable DDR2 memory system without the need for a complex timing closure process. For more information regarding the guidelines for using this DDR2 specification, see the Understanding TI’s PCB Routing Rule-Based DDR Timing Specification application report (literature number SPRAAV0). This application report provides generic guidelines and approach. All the specifications provided in the data manual take precedence over the generic guidelines and must be adhered to for a reliable DDR2 interface operation. 5.4.2.2.2.1 DDR2 Interface Schematic Figure 5-34 shows the schematic connections for 16-bit interface on AM335x device using one x16 DDR2 device and Figure 5-35 shows the schematic connections for 16-bit interface on AM335x using two x8 DDR2 devices. The AM335x DDR2 memory interface only supports 16-bit wide mode of operation. The AM335x device can only source one load connected to the DQS[x] and DQ[x] net class signals and two loads connected to the CK and ADDR_CTRL net class signals. For more information related to net classes, see Section 5.4.2.2.2.8. 142 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 16-Bit DDR2 Device AM335x DDR_D0 DDR_D7 DDR_DQM0 DDR_DQS0 DQ7 LDM LDQS DDR_DQSn0 DDR_D8 LDQS DQ8 DDR_D15 DDR_DQM1 DDR_DQS1 DDR_DQSn1 DQ15 UDM UDQS UDQS DDR_ODT T ODT DDR_BA0 T BA0 DDR_BA2 DDR_A0 T T BA2 A0 DDR_A15 DDR_CSn0 T T A15 CS DDR_CASn DDR_RASn DDR_WEn DDR_CKE DDR_CK T T T T T T CAS DDR_CKn RAS WE CKE CK CK DDR_VREF 0.1 µF (B) 0.1 µF (A) 1 K Ω 1% DDR_VREF VREF 0.1 µF DDR_RESETn VDDS_DDR PRODUCT PREVIEW DQ0 (B) 0.1 µF 1 K Ω 1% NC DDR_VTP 49.9 Ω (±1%, 20 mW) A. B. C. VDDS_DDR is the power supply for the DDR2 memories and the AM335x DDR2 interface. One of these capacitors can be eliminated if the divider and its capacitors are placed near a DDR_VREF pin. For all the termination requirements, see Section 5.4.2.2.2.9. Figure 5-34. 16-Bit DDR2 Interface Using One 16-Bit DDR2 Device Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 143 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 8-Bit DDR2 Devices AM335x DDR_D0 DQ0 DDR_D7 DDR_DQM0 DDR_DQS0 DQ7 DM DQS DDR_DQSn0 DQS DDR_D8 DQ0 DDR_D15 DDR_DQM1 DDR_DQS1 DDR_DQSn1 DQ7 DM DQS DQS PRODUCT PREVIEW DDR_ODT T ODT ODT DDR_BA0 T BA0 BA0 DDR_BA2 DDR_A0 T T BA2 A0 BA2 A0 DDR_A15 DDR_CSn0 T T A15 CS A15 CS DDR_CASn DDR_RASn DDR_WEn DDR_CKE DDR_CK T T T T T T CAS CAS RAS WE CKE CK CK RAS WE CKE CK CK DDR_CKn DDR_VREF VREF (B) 0.1 µF DDR_RESETn (B) 0.1 µF VDDS_DDR 0.1 µF (A) 1 K Ω 1% DDR_VREF VREF (B) 0.1 µF 0.1 µF 1 K Ω 1% NC DDR_VTP 49.9 Ω (±1%, 20 mW) A. B. C. VDDS_DDR is the power supply for the DDR2 memories and the AM335x DDR2 interface. One of these capacitors can be eliminated if the divider and its capacitors are placed near a DDR_VREF pin. For all the termination requirements, see Section 5.4.2.2.2.9. Figure 5-35. 16-Bit DDR2 Interface Using Two 8-Bit DDR2 Devices 144 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.2 Compatible JEDEC DDR2 Devices Table 5-37 shows the parameters of the JEDEC DDR2 devices that are compatible with this interface. Generally, the DDR2 interface is compatible with x16 or x8 DDR2-533 speed grade DDR2 devices. Table 5-37. Compatible JEDEC DDR2 Devices (Per Interface)(1) NO. PARAMETER 1 JEDEC DDR2 device speed grade(2) 2 JEDEC DDR2 device bit width 3 JEDEC DDR2 device count 4 JEDEC DDR2 device terminal count(3) MIN MAX UNIT DDR2-533 x8 x16 1 2 Devices Bits 60 84 Terminals (1) If the DDR2 interface is operated with a clock frequency less than 266 MHz, lower-speed grade DDR2 devices may be used if the minimum clock period specified for the DDR2 device is less than or equal to the minimum clock period selected for the AM335x DDR2 interface. (2) Higher DDR2 speed grades are supported due to inherent JEDEC DDR2 backwards compatibility. (3) 92-terminal devices are also supported for legacy reasons. New designs will migrate to 84-terminal DDR2 devices. Electrically, the 92and 84-terminal DDR2 devices are the same. The minimum stackup required for routing the AM335x device is a four-layer stackup as shown in Table 5-38. Additional layers may be added to the PCB stackup to accommodate other circuitry, enhance signal integrity and electromagnetic interference performance, or to reduce the size of the PCB footprint. Table 5-38. Minimum PCB Stackup (1) (1) LAYER TYPE DESCRIPTION 1 Signal Top signal routing 2 Plane Ground 3 Plane Split Power Plane 4 Signal Bottom signal routing All signals that have critical signal integrity requirements should be routed first on layer 1. It may not be possible to route all of these signals on layer 1 which requires some to be routed on layer 4. When this is done, the signal routes on layer 4 should not cross splits in the power plane. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 145 PRODUCT PREVIEW 5.4.2.2.2.3 PCB Stackup AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Complete stackup specifications are provided in Table 5-39. Table 5-39. PCB Stackup Specifications(1) NO. PARAMETER MIN TYP 1 PCB routing/plane layers 4 2 Signal routing layers 2 3 Full ground layers under DDR2 routing region 1 4 Number of ground plane cuts allowed within DDR2 routing region 5 Full VDDS_DDR power reference layers under DDR2 routing region 6 Number of layers between DDR2 routing layer and reference ground plane 7 PCB routing feature size 4 8 PCB trace width, w 4 9 PCB BGA escape via pad size(2) 10 13 Single-ended impedance, Zo(3) 14 0 0 18 PCB BGA escape via hole size AM335x BGA pad size Impedance control UNIT 1 (2) 11 MAX mils mils 20 10 ZCZ package 0.5 ZCE package 0.4 50 (4)(5) Zo-5 Zo mils mils mm 75 ohms Zo+5 ohms PRODUCT PREVIEW (1) For the DDR2 device BGA pad size, see the DDR2 device manufacturer documentation. (2) A 20/10 via may be used if enough power routing resources are available. An 18/10 via allows for more flexible power routing to the AM335x device. (3) Zo is the nominal singled-ended impedance selected for the PCB. (4) This parameter specifies the AC characteristic impedance tolerance for each segment of a PCB signal trace relative to the chosen Zo defined by the single-ended impedance parameter. (5) Tighter impedance control is required to ensure flight time skew is minimal. 146 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.4 Placement Figure 5-36 shows the required placement for the DDR2 devices. The dimensions for this figure are defined in Table 5-40. The placement does not restrict the side of the PCB on which the devices are mounted. The ultimate purpose of the placement is to limit the maximum trace lengths and allow for proper routing space. For single-memory DDR2 systems, the second DDR2 device is omitted from the placement. X Y OFFSET DDR2 Device Y Y OFFSET DDR2 Interface A1 AM335x Recommended DDR2 Device Orientation Figure 5-36. AM335x Device and DDR2 Device Placement Table 5-40. Placement Specifications(1) NO. MAX UNIT 1 X(2)(3) PARAMETER MIN 1750 mils 2 Y(2)(3) 1280 mils 650 mils (2)(3)(4) 3 Y Offset 4 Clearance from non-DDR2 signal to DDR2 keepout region(5)(6) 4 w (1) DDR2 keepout region to encompass entire DDR2 routing area. (2) For dimension definitions, see Figure 5-36. (3) Measurements from center of AM335x device to center of DDR2 device. (4) For single-memory systems, it is recommended that Y offset be as small as possible. (5) w is defined as the signal trace width. (6) Non-DDR2 signals allowed within DDR2 keepout region provided they are separated from DDR2 routing layers by a ground plane. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 147 PRODUCT PREVIEW A1 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.5 DDR2 Keepout Region The region of the PCB used for the DDR2 circuitry must be isolated from other signals. The DDR2 keepout region is defined for this purpose and is shown in Figure 5-37. This region should encompass all DDR2 circuitry and the region size varies with component placement and DDR2 routing. Additional clearances required for the keepout region are shown in Table 5-40. Non-DDR2 signals should not be routed on the same signal layer as DDR2 signals within the DDR2 keepout region. Non-DDR2 signals may be routed in the region provided they are routed on layers separated from DDR2 signal layers by a ground layer. No breaks should be allowed in the reference ground or VDDS_DDR power plane in this region. In addition, the VDDS_DDR power plane should cover the entire keepout region. DDR2 Device DDR2 Interface A1 A1 PRODUCT PREVIEW Figure 5-37. DDR2 Keepout Region 5.4.2.2.2.6 Bulk Bypass Capacitors Bulk bypass capacitors are required for moderate speed bypassing of the DDR2 and other circuitry. Table 5-41 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note that this table only covers the bypass needs of the AM335x DDR2 interface and DDR2 device(s). Additional bulk bypass capacitance may be needed for other circuitry. Table 5-41. Bulk Bypass Capacitors(1) NO. PARAMETER MIN MAX UNIT 1 AM335x VDDS_DDR bulk bypass capacitor count 1 2 AM335x VDDS_DDR bulk bypass total capacitance 10 μF 1 Devices 10 μF 1 Devices 10 μF 3 DDR2#1 bulk bypass capacitor count 4 DDR2#1 bulk bypass total capacitance 5 DDR2#2 bulk bypass capacitor count (2) 6 DDR2#2 bulk bypass total capacitance(2) Devices (1) These devices should be placed near the device they are bypassing, but preference should be given to the placement of the high-speed (HS) bypass capacitors. (2) Only used when two DDR2 devices are used. 148 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.7 High-Speed Bypass Capacitors High-speed (HS) bypass capacitors are critical for proper DDR2 interface operation. It is particularly important to minimize the parasitic series inductance of the HS bypass capacitors, AM335x/DDR2 power, and AM335x/DDR2 ground connections. Table 5-42 contains the specification for the HS bypass capacitors as well as for the power connections on the PCB. Table 5-42. High-Speed Bypass Capacitors PARAMETER MIN 1 HS bypass capacitor package size(1) 2 Distance from HS bypass capacitor to device being bypassed 3 Number of connection vias for each HS bypass capacitor(2) 4 Trace length from bypass capacitor contact to connection via 5 Number of connection vias for each AM335x VDDS_DDR/VSS terminal 6 Trace length from AM335x VDDS_DDR/VSS terminal to connection via 7 Number of connection vias for each DDR2 device power/ground terminal 8 Trace length from DDR2 device power/ground terminal to connection via 10 30 DDR2 device HS bypass capacitor total capacitance(4) mils Vias 35 mils 1 Vias 35 0.6 12 mils Vias 1 AM335x VDDS_DDR HS bypass capacitor total capacitance DDR2 device HS bypass capacitor count(3)(4) 10 mils 250 10 11 UNIT 0402 2 AM335x VDDS_DDR HS bypass capacitor count(3) 9 MAX 8 mils Devices μF Devices 0.4 μF (1) LxW, 10-mil units; i.e., a 0402 is a 40x20-mil surface-mount capacitor. (2) An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board. (3) These devices should be placed as close as possible to the device being bypassed. (4) Per DDR2 device. 5.4.2.2.2.8 Net Classes Table 5-43 lists the clock net classes for the DDR2 interface. Table 5-44 lists the signal net classes, and associated clock net classes, for the signals in the DDR2 interface. These net classes are used for the termination and routing rules that follow. Table 5-43. Clock Net Class Definitions CLOCK NET CLASS AM335x PIN NAMES CK DDR_CK/DDR_CKn DQS0 DDR_DQS0/DDR_DQSn0 DQS1 DDR_DQS1/DDR_DQSn1 Table 5-44. Signal Net Class Definitions SIGNAL NET CLASS ASSOCIATED CLOCK NET CLASS ADDR_CTRL CK DQ0 DQS0 DDR_D[7:0], DDR_DQM0 DQ1 DQS1 DDR_D[15:8], DDR_DQM1 AM335x PIN NAMES DDR_BA[2:0], DDR_A[15:0], DDR_CSn0, DDR_CASn, DDR_RASn, DDR_WEn, DDR_CKE, DDR_ODT Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 149 PRODUCT PREVIEW NO. AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.9 DDR2 Signal Termination Signal terminations are required on the CK and ADDR_CTRL net class signals. Serial terminations should be used on the CK and ADDR_CTRL lines and is the preferred termination scheme. On-device terminations (ODTs) are required on the DQS[x] and DQ[x] net class signals. They should be enabled to ensure signal integrity. Table 5-45 shows the specifications for the series terminators. Placement of serial terminations for ADDR_CTRL net class signals should be close to the AM335x device. Table 5-45. DDR2 Signal Terminations NO. PARAMETER MIN 1 CK net class(1) 0 2 ADDR_CTRL net class(1)(2)(3) 0 3 DQS0, DQS1, DQ0, and DQ1 net classes(5) TYP 22 NA MAX UNIT 10 ohms Zo(4) ohms NA ohms (1) Only series termination is permitted. (2) Series termination values larger than typical only recommended to address EMI issues. (3) Series termination values should be uniform across net class. (4) Zo is the DDR2 PCB trace characteristic impedance. (5) No external termination resistors are allowed and ODT must be used for these net classes. PRODUCT PREVIEW If the DDR2 interface is operated at a lower frequency (<200-MHz clock rate), on-device terminations are not specifically required for the DQS[x] and DQ[x] net class signals and serial terminations for the CK and ADDR_CTRL net class signals are not mandatory. System designers may evaluate the need for serial terminators for EMI and overshoot reduction. Placement of serial terminations for DQS[x] and DQ[x] net class signals should be determined based on PCB analysis. Placement of serial terminations for ADDR_CTRL net class signals should be close to the AM335x device. Table 5-46 shows the specifications for the serial terminators in such cases. Table 5-46. Lower-Frequency DDR2 Signal Terminations No. Min Typ Max Unit 1 CK net class(1) 0 22 Zo(2) ohms 2 ADDR_CTRL net class(1)(3)(4) 0 22 Zo(2) ohms 22 (2) ohms 3 Parameter DQS0, DQS1, DQ0, and DQ1 net classes 0 Zo (1) Only series termination is permitted. (2) Zo is the DDR2 PCB trace characteristic impedance. (3) Series termination values larger than typical only recommended to address EMI issues. (4) Series termination values should be uniform across net class. 150 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.2.10 DDR_VREF Routing DDR_VREF is used as a reference by the input buffers of the DDR2 memories as well as the AM335x device. DDR_VREF is intended to be half the DDR2 power supply voltage and should be created using a resistive divider as shown in Figure 5-34 and Figure 5-35. Other methods of creating DDR_VREF are not recommended. Figure 5-38 shows the layout guidelines for DDR_VREF. DDR_VREF Bypass Capacitor DDR2 Device A1 DDR_VREF Nominal Minimum Trace Width is 20 Mils AM335x A1 PRODUCT PREVIEW Neck down to minimum in BGA escape regions is acceptable. Narrowing to accommodate via congestion for short distances is also acceptable. Best performance is obtained if the width of DDR_VREF is maximized. Figure 5-38. DDR_VREF Routing and Topology Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 151 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.2.3 DDR2 CK and ADDR_CTRL Routing Figure 5-39 shows the topology of the routing for the CK and ADDR_CTRL net classes. The length of signal path AB and AC should be minimized with emphasis to minimize lengths C and D such that length A is the majority of the total length of signal path AB and AC. T C A DDR2 Interface B A1 AM335x A1 Figure 5-39. CK and ADDR_CTRL Routing and Topology NO. PARAMETER MIN TYP MAX UNIT 1 Center-to-center CK spacing 2w 2 CK differential pair skew length mismatch(2)(3) 25 mils 3 CK B-to-CK C skew length mismatch 25 mils 4 Center-to-center CK to other DDR2 trace spacing(4) 5 CK/ADDR_CTRL nominal trace length(5) CACLM+50 mils 6 ADDR_CTRL-to-CK skew length mismatch 100 mils 7 ADDR_CTRL-to-ADDR_CTRL skew length mismatch 100 mils 8 Center-to-center ADDR_CTRL to other DDR2 trace spacing(4) 4w 3w 4w CACLM-50 CACLM 9 Center-to-center ADDR_CTRL to other ADDR_CTRL trace spacing(4) 10 ADDR_CTRL A-to-B/ADDR_CTRL A-to-C skew length mismatch(2) 100 mils 11 ADDR_CTRL B-to-C skew length mismatch 100 mils (1) CK represents the clock net class, and ADDR_CTRL represents the address and control signal net class. (2) Series terminator, if used, should be located closest to the AM335x device. (3) Differential impedance should be Zo x 2, where Zo is the single-ended impedance defined in Table 5-39. (4) Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. (5) CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes. Figure 5-40 shows the topology and routing for the DQS[x] and DQ[x] net classes; the routes are point to point. Skew matching across bytes is not needed nor recommended. A1 DQ[0] DQ[1] DDR2 Interface PRODUCT PREVIEW Table 5-47. CK and ADDR_CTRL Routing Specification(1)(2) AM335x Figure 5-40. DQS[x] and DQ[x] Routing and Topology 152 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-48. DQS[x] and DQ[x] Routing Specification(1) NO. PARAMETER MIN 1 Center-to-center DQS[x] spacing 2 DQS[x] differential pair skew length mismatch(2) 3 Center-to-center DDR_DQS[x] to other DDR2 trace spacing(3) 4 DQS[x]/DQ[x] nominal trace length(4) 5 DQ[x]-to-DQS[x] skew length mismatch(4) 6 DQ[x]-to-DQ[x] skew length mismatch(4) TYP MAX UNIT 2w 25 mils DQLM+50 mils 100 mils 100 mils 4w DQLM-50 7 Center-to-center DQ[x] to other DDR2 trace spacing (3)(5) 4w 8 Center-to-center DQ[x] to other DQ[x] trace spacing(3)(6) 3w DQLM (1) DQS[x] represents the DQS0 and DQS1 clock net classes, and DQ[x] represents the DQ0 and DQ1 signal net classes. (2) Differential impedance should be Zo x 2, where Zo is the single-ended impedance defined in Table 5-39. (3) Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. (4) There is no requirement, and it is not recommended, to skew match between data bytes; i.e., from net classes DQS0 and DQ0 to net classes DQS1 and DQ1. (5) Signals from one DQ net class should be considered other DDR2 traces to another DQ net class. PRODUCT PREVIEW (6) DQLM is the longest Manhattan distance of each of the DQS[x] and DQ[x] net classes. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 153 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.4.2.3 www.ti.com DDR3 Routing Guidelines 5.4.2.3.1 Board Designs TI only supports board designs utilizing DDR3 memory that follow the guidelines in this document. The switching characteristics and timing diagram for the DDR3 memory interface are shown in Table 5-49 and Figure 5-41. Table 5-49. Switching Characteristics Over Recommended Operating Conditions for DDR3 Memory Interface NO. 1 PARAMETER MIN MAX UNIT tc(DDR_CK/DDR_CKn) Cycle time, DDR_CK/DDR_CKn 3.3 3.3(1) ns (1) The JEDEC JESD79-3E specification defines the maximum clock period of 3.3 ns for all standard-speed bin DDR3 memory devices. Therefore, all standard-speed bin DDR3 memory devices are required to operate at 303 MHz. 1 DDR_CK DDR_CKn PRODUCT PREVIEW Figure 5-41. DDR3 Memory Interface Clock Timing 5.4.2.3.1.1 DDR3 versus DDR2 This specification only covers AM335x PCB designs that utilize DDR3 memory. Designs using DDR2 memory should use the DDR2 routing guidleines described in Section 5.4.2.2. While similar, the two memory systems have different requirements. It is currently not possible to design one PCB that meets the requirements of both DDR2 and DDR3. 5.4.2.3.2 DDR3 Device Combinations Since there are several possible combinations of device counts and single-side or dual-side mounting, Table 5-50 summarizes the supported device configurations. Table 5-50. Supported DDR3 Device Combinations NUMBER OF DDR3 DEVICES DDR3 DEVICE WIDTH (BITS) MIRRORED? DDR3 EMIF WIDTH (BITS) 1 2 16 N 16 8 Y(1) 16 (1) Two DDR3 devices are mirrored when one device is placed on the top of the board and the second device is placed on the bottom of the board. 5.4.2.3.3 DDR3 Interface 5.4.2.3.3.1 DDR3 Interface Schematic The DDR3 interface schematic varies, depending upon the width of the DDR3 devices used. Figure 5-42 shows the schematic connections for 16-bit interface on AM335x device using one x16 DDR3 device and Figure 5-43 shows the schematic connections for 16-bit interface on AM335x device using two x8 DDR3 devices. The AM335x DDR3 memory interface only supports 16-bit wide mode of operation. The AM335x device can only source one load connected to the DQS[x] and DQ[x] net class signals and two loads connected to the CK and ADDR_CTRL net class signals. For more information related to net classes, see Section 5.4.2.3.3.8. 154 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 16-Bit DDR3 Interface 16-Bit DDR3 Device DDR_D15 DQU7 8 DDR_D8 DQU0 DDR_DQM1 DDR_DQS1 DDR_DQSn1 DMU DQSU DQSU# DDR_D7 DQL7 8 DDR_D0 DQL0 DDR_DQM0 DDR_DQS0 DDR_DQSn0 DML DQSL DQSL# DDR_CK DDR_CKn CK CK# DDR_ODT DDR_CSn0 DDR_BA0 DDR_BA1 DDR_BA2 Zo VDDS_DDR Zo ODT CS# BA0 BA1 BA2 DDR_A0 0.1 µF DDR_VTT A0 Zo A15 Zo DDR_A15 DDR_CASn DDR_RASn DDR_WEn DDR_CKE DDR_RESETn ZQ DDR_VREF 0.1 µF CAS# RAS# WE# CKE RESET# ZQ VREFDQ VREFCA 0.1 µF PRODUCT PREVIEW 15 DDR_VREF 0.1 µF DDR_VTP 49.9 Ω (±1%, 20 mW) Zo ZQ Termination is required. See terminator comments. Value determined according to the DDR3 memory device data sheet. Figure 5-42. 16-Bit DDR3 Interface Using One 16-Bit DDR3 Device Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 155 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 16-Bit DDR3 Interface 8-Bit DDR3 Devices DDR_D15 DQ7 8 DDR_D8 DQ0 DDR_DQM1 NC DDR_DQS1 DDR_DQSn1 DDR_D7 DM/TDQS TDQS# DQS DQS# DQ7 8 DDR_D0 DQ0 DDR_DQM0 NC DDR_DQS0 DDR_DQSn0 DDR_CK DDR_CKn DDR_ODT DDR_CSn0 DDR_BA0 DDR_BA1 DDR_BA2 PRODUCT PREVIEW DDR_A0 DM/TDQS TDQS# DQS DQS# Zo CK CK# CK CK# ODT CS# BA0 BA1 BA2 ODT CS# BA0 BA1 BA2 A0 A0 Zo A15 A15 Zo CAS# RAS# WE# CKE RESET# ZQ VREFDQ VREFCA CAS# RAS# WE# CKE RESET# ZQ VREFDQ VREFCA 0.1 µF VDDS_DDR Zo DDR_VTT 15 DDR_A15 DDR_CASn DDR_RASn DDR_WEn DDR_CKE DDR_RESETn ZQ DDR_VREF 0.1 µF 0.1 µF 0.1 µF DDR_VREF ZQ 0.1 µF DDR_VTP 49.9 Ω (±1%, 20 mW) Zo ZQ Termination is required. See terminator comments. Value determined according to the DDR3 memory device data sheet. Figure 5-43. 16-Bit DDR3 Interface Using Two 8-Bit DDR3 Devices 156 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.3.2 Compatible JEDEC DDR3 Devices Table 5-51 shows the parameters of the JEDEC DDR3 devices that are compatible with this interface. Generally, the DDR3 interface is compatible with DDR3-800 devices in the x8 or x16 widths. Table 5-51. Compatible JEDEC DDR3 Devices (Per Interface) NO. PARAMETER MIN MAX 1 JEDEC DDR3 device speed grade(1) 2 JEDEC DDR3 device bit width x8 x16 3 JEDEC DDR3 device count(2) 1 2 UNIT DDR3-800 Bits Devices (1) DDR3 speed grade depends on desired clock rate. Data rate is 2x the clock rate. For DDR3-800, the clock rate is 400 MHz. (2) For valid DDR3 device configurations and device counts, see Section 5.4.2.3.3.1, Figure 5-42, and Figure 5-43. 5.4.2.3.3.3 PCB Stackup The minimum stackup for routing the DDR3 interface is a four-layer stack up as shown in Table 5-52. Additional layers may be added to the PCB stackup to accommodate other circuitry, enhance signal integrity and electromagnetic interference performance, or to reduce the size of the PCB footprint. (1) LAYER TYPE DESCRIPTION 1 Signal Top signal routing 2 Plane Ground 3 Plane Split Power Plane 4 Signal Bottom signal routing PRODUCT PREVIEW Table 5-52. Minimum PCB Stackup (1) All signals that have critical signal integrity requirements should be routed first on layer 1. It may not be possible to route all of these signals on layer 1 which requires some to be routed on layer 4. When this is done, the signal routes on layer 4 should not cross splits in the power plane. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 157 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-53. PCB Stackup Specifications(1) NO. PARAMETER MIN 1 PCB routing/plane layers 4 2 Signal routing layers 2 3 Full ground reference layers under DDR3 routing region(2) TYP MAX 1 (2) 4 Full VDDS_DDR power reference layers under the DDR3 routing region 5 Number of reference plane cuts allowed within DDR3 routing region(3) 0 6 Number of layers between DDR3 routing layer and reference plane(4) 0 7 PCB routing feature size 4 8 PCB trace width, w 4 9 PCB BGA escape via pad size(5) 10 PCB BGA escape via hole size 11 AM335x BGA pad size 13 Single-ended impedance, Zo(6) 14 Impedance control UNIT 1 18 mils mils 20 10 ZCZ package 0.5 ZCE package 0.4 50 (7)(8) Zo-5 Zo mils mils mm 75 ohms Zo+5 ohms (1) For the DDR3 device BGA pad size, see the DDR3 device manufacturer documentation. PRODUCT PREVIEW (2) Ground reference layers are preferred over power reference layers. Be sure to include bypass caps to accommodate reference layer return current as the trace routes switch routing layers. (3) No traces should cross reference plane cuts within the DDR3 routing region. High-speed signal traces crossing reference plane cuts create large return current paths which can lead to excessive crosstalk and EMI radiation. (4) Reference planes are to be directly adjacent to the signal plane to minimize the size of the return current loop. (5) An 18-mil pad assumes Via Channel is the most economical BGA escape. A 20-mil pad may be used if additional layers are available for power routing. An 18-mil pad is required for minimum layer count escape. (6) Zo is the nominal singled-ended impedance selected for the PCB. (7) This parameter specifies the AC characteristic impedance tolerance for each segment of a PCB signal trace relative to the chosen Zo defined by the single-ended impedance parameter. (8) Tighter impedance control is required to ensure flight time skew is minimal. 158 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.3.4 Placement Figure 5-44 shows the required placement for the AM335x device as well as the DDR3 devices. The dimensions for this figure are defined in Table 5-54. The placement does not restrict the side of the PCB on which the devices are mounted. The ultimate purpose of the placement is to limit the maximum trace lengths and allow for proper routing space. X1 X2 DDR3 Interface Y Table 5-54. Placement Specifications(1) NO. PARAMETER 1 X1(2)(3)(4) 2 (2)(3) X2 3 Y Offset(2)(3)(4) 4 Clearance from non-DDR3 signal to DDR3 keepout region(5)(6) MIN MAX UNIT 1000 mils 600 mils 1500 mils 4 w (1) DDR3 keepout region to encompass entire DDR3 routing area. (2) For dimension definitions, see Figure 5-44. (3) Measurements from center of AM335x device to center of DDR3 device. (4) Minimizing X1 and Y improves timing margins. (5) w is defined as the signal trace width. (6) Non-DDR3 signals allowed within DDR3 keepout region provided they are separated from DDR3 routing layers by a ground plane. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 159 PRODUCT PREVIEW Figure 5-44. Placement Specifications AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.3.5 DDR3 Keepout Region The region of the PCB used for DDR3 circuitry must be isolated from other signals. The DDR3 keepout region is defined for this purpose and is shown in Figure 5-45. This region should encompass all DDR3 circuitry and the region size varies with component placement and DDR3 routing. Additional clearances required for the keepout region are shown in Table 5-54. Non-DDR3 signals should not be routed on the same signal layer as DDR3 signals within the DDR3 keepout region. Non-DDR3 signals may be routed in the region provided they are routed on layers separated from DDR3 signal layers by a ground layer. No breaks should be allowed in the reference ground or VDDS_DDR power plane in this region. In addition, the VDDS_DDR power plane should cover the entire keepout region. DDR3 Interface DDR3 Keepout Region Encompasses Entire DDR3 Routing Area PRODUCT PREVIEW Figure 5-45. DDR3 Keepout Region 5.4.2.3.3.6 Bulk Bypass Capacitors Bulk bypass capacitors are required for moderate speed bypassing of the DDR3 and other circuitry. Table 5-55 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note that this table only covers the bypass needs of the AM335x DDR3 interface and DDR3 device(s). Additional bulk bypass capacitance may be needed for other circuitry. Table 5-55. Bulk Bypass Capacitors(1) NO. PARAMETER MIN MAX 2 UNIT 1 AM335x VDDS_DDR bulk bypass capacitor count Devices 2 AM335x VDDS_DDR bulk bypass total capacitance 3 DDR3#1 bulk bypass capacitor count 4 DDR3#1 bulk bypass total capacitance 20 μF 5 DDR3#2 bulk bypass capacitor count(2) 2 Devices 6 DDR3#2 bulk bypass total capacitance(2) 20 μF 20 μF 2 Devices (1) These devices should be placed near the devices they are bypassing, but preference should be given to the placement of the high-speed (HS) bypass capacitors and DDR3 signal routing. (2) Only used when two DDR3 devices are used. 160 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.3.7 High-Speed Bypass Capacitors High-speed (HS) bypass capacitors are critcal for proper DDR3 interface operation. It is particularly important to minimize the parasitic series inductance of the HS bypass capacitors, AM335x/DDR3 power, and AM335x/DDR3 ground connections. Table 5-56 contains the specification for the HS bypass capacitors as well as for the power connections on the PCB. Generally speaking, it is good to: 1. Fit as many HS bypass capacitors as possible. 2. Minimize the distance from the bypass cap to the power terminals being bypassed. 3. Use the smallest physical sized capacitors possible with the highest capacitance readily available. 4. Connect the bypass capacitor pads to their vias using the widest traces possible and using the largest hole size via possible. 5. Minimize via sharing. Note the limites on via sharing shown in Table 5-56. NO. PARAMETER MIN (1) 1 HS bypass capacitor package size 2 Distance, HS bypass capacitor to AM335x VDDS_DDR/VSS terminal being bypassed(2)(3)(4) 3 AM335x VDDS_DDR HS bypass capacitor count 4 AM335x VDDS_DDR HS bypass capacitor total capacitance 5 Trace length from AM335x VDDS_DDR/VSS terminal to connection via(2) 6 Distance, HS bypass capacitor to DDR3 device being bypassed(5) (6) 7 DDR3 device HS bypass capacitor count 8 DDR3 device HS bypass capacitor total capacitance(6) 9 Number of connection vias for each HS bypass capacitor(7)(8) 10 Trace length from bypass capacitor connect to connection via(2)(8) 11 Number of connection vias for each DDR3 device power/ground terminal(9) 12 Trace length from DDR3 device power/ground terminal to connection via(2)(7) TYP MAX UNIT 0201 0402 10 mils 400 mils 20 Devices μF 1 35 70 mils 150 mils 12 Devices μF 0.85 2 Vias 35 100 1 mils Vias 35 60 mils (1) LxW, 10-mil units, i.e., a 0402 is a 40x20-mil surface-mount capacitor. (2) Closer/shorter is better. (3) Measured from the nearest AM335x VDDS_DDR and ground terminal to the center of the capacitor package. (4) Three of these capacitors should be located underneath the AM335x device, between the cluster of VDDS_DDR and ground terminals, between the DDR3 interfaces on the package. (5) Measured from the DDR3 device power/ground terminal to the center of the capacitor package. (6) Per DDR3 device. (7) An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board. No sharing of vias is permitted on the same side of the board. (8) An HS bypass capacitor may share a via with a DDR3 device mounted on the same side of the PCB. A wide trace should be used for the connection and the length from the capacitor pad to the DDR3 device pad should be less than 150 mils. (9) Up to a total of two pairs of DDR3 power/ground terminals may share a via. 5.4.2.3.3.7.1 Return Current Bypass Capacitors Use additional bypass capacitors if the return current reference plane changes due to DDR3 signals hopping from one signal layer to another. The bypass capacitor here provides a path for the return current to hop planes along with the signal. As many of these return current bypass capacitors should be used as possible. Since these are returns for signal current, the signal via size may be used for these capacitors. 5.4.2.3.3.8 Net Classes Table 5-57 lists the clock net classes for the DDR3 interface. Table 5-58 lists the signal net classes, and associated clock net classes, for signals in the DDR3 interface. These net classes are used for the termination and routing rules that follow. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 161 PRODUCT PREVIEW Table 5-56. High-Speed Bypass Capacitors AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-57. Clock Net Class Definitions CLOCK NET CLASS AM335x PIN NAMES CK DDR_CK/DDR_CKn DQS0 DDR_DQS0/DDR_DQSn0 DQS1 DDR_DQS1/DDR_DQSn1 Table 5-58. Signal Net Class Definitions SIGNAL NET CLASS ASSOCIATED CLOCK NET CLASS ADDR_CTRL CK DQ0 DQS0 DDR_D[7:0], DDR_DQM0 DQ1 DQS1 DDR_D[15:8], DDR_DQM1 AM335x PIN NAMES DDR_BA[2:0], DDR_A[15:0], DDR_CSn0, DDR_CASn, DDR_RASn, DDR_WEn, DDR_CKE, DDR_ODT 5.4.2.3.3.9 DDR3 Signal Termination Signal terminations are required for the CK and ADDR_CTRL net class signals. On-device terminations (ODTs) are required on the DQS[x] and DQ[x] net class signals. Detailed termination specifications are covered in the routing rules in the following sections. PRODUCT PREVIEW 5.4.2.3.3.10 DDR_VREF Routing DDR_VREF is used as a reference by the input buffers of the DDR3 memories as well as the AM335x device. DDR_VREF is intended to be half the DDR3 power supply voltage and is typically generated with a voltage divider connected to the VDDS_DDR power supply. It should be routed as a nominal 20-mil wide trace with 0.1 µF bypass capacitors near each device connection. Narrowing of DDR_VREF is allowed to accommodate routing congestion. 5.4.2.3.3.11 VTT Like DDR_VREF, the nominal value of the VTT supply is half the DDR3 supply voltage. Unlike DDR_VREF, VTT is expected to source and sink current, specifically the termination current for the ADDR_CTRL net class Thevinen terminators. VTT is needed at the end of the address bus and it should be routed as a power sub-plane. VTT should be bypassed near the terminator resistors. 5.4.2.3.4 DDR3 CK and ADDR_CTRL Topologies and Routing Definition The CK and ADDR_CTRL net classes are routed similarly and are length matched to minimize skew between them. CK is a bit more complicated because it runs at a higher transition rate and is differential. The following subsections show the topology and routing for various DDR3 configurations for CK and ADDR_CTRL. The figures in the following subsections define the terms for the routing specification detailed in Table 5-59. 5.4.2.3.4.1 Two DDR3 Devices Two DDR3 devices are supported on the DDR3 interface consisting of two x8 DDR3 devices arranged as one 16-bit bank. These two devices may be mounted on a single side of the PCB, or may be mirrored in a pair to save board space at a cost of increased routing complexity and parts on the backside of the PCB. 5.4.2.3.4.1.1 CK and ADDR_CTRL Topologies, Two DDR3 Devices Figure 5-46 shows the topology of the CK net classes and Figure 5-47 shows the topology for the corresponding ADDR_CTRL net classes. 162 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com + – + – AS+ AS- AS+ AS- DDR3 Differential CK Input Buffers Clock Parallel Terminator VDDS_DDR Rcp A1 AM335x Differential Clock Output Buffer A3 A2 AT Cac + – Rcp A1 A3 A2 0.1 µF AT Routed as Differential Pair PRODUCT PREVIEW Figure 5-46. CK Topology for Two DDR3 Devices AM335x Address/Control Output Buffer A1 A2 AS AS DDR3 Address/Control Input Buffers A3 Address/Control Terminator Rtt Vtt AT Figure 5-47. ADDR_CTRL Topology for Two DDR3 Devices 5.4.2.3.4.1.2 CK and ADDR_CTRL Routing, Two DDR3 Devices Figure 5-48 shows the CK routing for two DDR3 devices placed on the same side of the PCB. Figure 5-49 shows the corresponding ADDR_CTRL routing. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 163 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 A1 A1 www.ti.com VDDS_DDR A3 A3 = Rcp Cac Rcp 0.1 µF AT AT AS+ AS- A2 A2 Figure 5-48. CK Routing for Two Single-Side DDR3 Devices A1 PRODUCT PREVIEW Rtt A3 = AT Vtt AS A2 Figure 5-49. ADDR_CTRL Routing for Two Single-Side DDR3 Devices 164 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com A1 A1 To save PCB space, the two DDR3 memories may be mounted as a mirrored pair at a cost of increased routing and assembly complexity. Figure 5-50 and Figure 5-51 show the routing for CK and ADDR_CTRL, respectively, for two DDR3 devices mirrored in a single-pair configuration. VDDS_DDR A3 A3 Cac Rcp 0.1 µF PRODUCT PREVIEW = Rcp AT AT AS+ AS- A2 A2 A1 Figure 5-50. CK Routing for Two Mirrored DDR3 Devices Rtt = AT Vtt AS A3 A2 Figure 5-51. ADDR_CTRL Routing for Two Mirrored DDR3 Devices Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 165 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.4.2 One DDR3 Device A single DDR3 device is supported on the DDR3 interface consisting of one x16 DDR3 device arranged as one 16-bit bank. 5.4.2.3.4.2.1 CK and ADDR_CTRL Topologies, One DDR3 Device Figure 5-52 shows the topology of the CK net classes and Figure 5-53 shows the topology for the corresponding ADDR_CTRL net classes. DDR3 Differential CK Input Buffer AS+ AS- + – Clock Parallel Terminator VDDS_DDR Rcp A1 PRODUCT PREVIEW AM335x Differential Clock Output Buffer AT A2 Cac + – Rcp A1 0.1 µF AT A2 Routed as Differential Pair Figure 5-52. CK Topology for One DDR3 Device AS DDR3 Address/Control Input Buffers AM335x Address/Control Output Buffer A1 A2 Address/Control Terminator Rtt AT Vtt Figure 5-53. ADDR_CTRL Topology for One DDR3 Device 166 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.4.2.2 CK and ADDR/CTRL Routing, One DDR3 Device A1 A1 Figure 5-54 shows the CK routing for one DDR3 device. Figure 5-55 shows the corresponding ADDR_CTRL routing. VDDS_DDR Rcp Cac Rcp 0.1 µF AT AT PRODUCT PREVIEW = AS+ AS- A2 A2 A1 Figure 5-54. CK Routing for One DDR3 Device Rtt AT = Vtt AS A2 Figure 5-55. ADDR_CTRL Routing for One DDR3 Device 5.4.2.3.5 Data Topologies and Routing Definition No matter the number of DDR3 devices used, the data line topology is always point to point, so its definition is simple. 5.4.2.3.5.1 DQS[x] and DQ[x] Topologies, Any Number of Allowed DDR3 Devices DQS[x] lines are point-to-point differential, and DQ[x] lines are point-to-point singled ended. Figure 5-56 and Figure 5-57 show these topologies. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 167 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com AM335x DQS[x] I/O Buffer DDR3 DQS[x] I/O Buffer DQS[x]+ DQS[x]Routed Differentially x = 0, 1 Figure 5-56. DQS[x] Topology AM335x DQ[x] I/O Buffer DDR3 DQ[x] I/O Buffer DQ[x] x = 0, 1 Figure 5-57. DQ[x] Topology 5.4.2.3.5.2 DQS[x] and DQ[x] Routing, Any Number of Allowed DDR3 Devices Figure 5-58 and Figure 5-59 show the DQS[x] and DQ[x] routing. PRODUCT PREVIEW DQS[x]+ DQS[x]- DQS[x] Routed Differentially x = 0, 1 Figure 5-58. DQS[x] Routing With Any Number of Allowed DDR3 Devices DQ[x] x = 0, 1 Figure 5-59. DQ[x] Routing With Any Number of Allowed DDR3 Devices 168 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 5.4.2.3.6 Routing Specification 5.4.2.3.6.1 CK and ADDR_CTRL Routing Specification Skew within the CK and ADDR_CTRL net classes directly reduces setup and hold margin and, thus, this skew must be controlled. The only way to practically match lengths on a PCB is to lengthen the shorter traces up to the length of the longest net in the net class and its associated clock. A metric to establish this maximum length is Manhattan distance. The Manhattan distance between two points on a PCB is the length between the points when connecting them only with horizontal or vertical segments. A reasonable trace route length is to within a percentage of its Manhattan distance. CACLM is defined as Clock Address Control Longest Manhattan distance. (A) A1 A8 PRODUCT PREVIEW Given the clock and address pin locations on the AM335x device and the DDR3 memories, the maximum possible Manhattan distance can be determined given the placement. Figure 5-60 shows this distance for two loads. It is from this distance that the specifications on the lengths of the transmission lines for the address bus are determined. CACLM is determined similarly for other address bus configurations; i.e., it is based on the longest net of the CK/ADDR_CTRL net class. For CK and ADDR_CTRL routing, these specifications are contained in Table 5-59. CACLMY CACLMX A8 (A) A8 (A) Rtt A3 = A. AT Vtt AS A2 It is very likely that the longest CK/ADDR_CTRL Manhattan distance will be for Address Input 8 (A8) on the DDR3 memories. CACLM is based on the longest Manhattan distance due to the device placement. Verify the net class that satisfies this criteria and use as the baseline for CK/ADDR_CTRL skew matching and length control. The length of shorter CK/ADDR_CTRL stubs as well as the length of the terminator stub are not included in this length calculation. Non-included lengths are grayed out in the figure. Assuming A8 is the longest, CALM = CACLMY + CACLMX + 300 mils. The extra 300 mils allows for routing down lower than the DDR3 memories and returning up to reach A8. Figure 5-60. CACLM for Two Address Loads on One Side of PCB Table 5-59. CK and ADDR_CTRL Routing Specification(1)(2)(3) NO. PARAMETER MIN TYP MAX UNIT 2500 mils 25 mils 660 mils 1 A1+A2 length 2 A1+A2 skew 3 A3 length 4 A3 skew(4) 25 mils 5 (5) A3 skew 125 mils 6 AS length 100 mils Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 169 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-59. CK and ADDR_CTRL Routing Specification(1)(2)(3) (continued) NO. MAX UNIT 7 AS skew PARAMETER MIN TYP 25 mils 8 AS+/AS- length 70 mils 9 AS+/AS- skew 5 mils 10 AT length(6) 500 (7) 11 AT skew 12 AT skew(8) 13 CK/ADDR_CTRL nominal trace length(9) mils 100 CACLM-50 (10) CACLM mils 5 mils CACLM+50 mils 14 Center-to-center CK to other DDR3 trace spacing 15 Center-to-center ADDR_CTRL to other DDR3 trace spacing(10)(11) 4w 4w 16 Center-to-center ADDR_CTRL to other ADDR_CTRL trace spacing(10) 3w 17 CK center-to-center spacing(12) 18 CK spacing to other net(10) 19 Rcp(13) Zo-1 Zo Zo+ ohms 20 Rtt(13)(14) Zo-5 Zo Zo+5 ohms 4w (1) CK represents the clock net class, and ADDR_CTRL represents the address and control signal net class. (2) The use of vias should be minimized. PRODUCT PREVIEW (3) Additional bypass capacitors are required when using the VDDS_DDR plane as the reference plane to allow the return current to jump between the VDDS_DDR plane and the ground plane when the net class switches layers at a via. (4) Mirrored configuration (one DDR3 device on top of the board and one DDR3 device on the bottom). (5) Non-mirrored configuration (all DDR3 memories on same side of PCB). (6) While this length can be increased for convenience, its length should be minimized. (7) ADDR_CTRL net class only (not CK net class). Minimizing this skew is recommended, but not required. (8) CK net class only. (9) CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes + 300 mils. For definition, see Section 5.4.2.3.6.1 and Figure 5-60. (10) Center-to-center spacing is allowed to fall to minimum (w) for up to 1250 mils of routed length. (11) Signals from one DQ net class should be considered other DDR3 traces to another DQ net class. (12) CK spacing set to ensure proper differential impedance. (13) Source termination (series resistor at driver) is specifically not allowed. (14) Termination values should be uniform across the net class. 5.4.2.3.6.2 DQS[x] and DQ[x] Routing Specification Skew within the DQS[x] and DQ[x] net classes directly reduces setup and hold margin and, thus, this skew must be controlled. The only way to practically match lengths on a PCB is to lengthen the shorter traces up to the length of the longest net in the net class and its associated clock. DQLMn is defined as DQ Longest Manhattan distance n, where n is the byte number. For a 16-bit interface, there are two DQLMs, DQLM0-DQLM1. NOTE It is not required, nor is it recommended, to match the lengths across all bytes. Length matching is only required within each byte. Given the DQS[x] and DQ[x] pin locations on the AM335x device and the DDR3 memories, the maximum possible Manhattan distance can be determined given the placement. Figure 5-61 shows this distance for a two-load case. It is from this distance that the specifications on the lengths of the transmission lines for the data bus are determined. For DQS[x] and DQ[x] routing, these specifications are contained in Table 5-60. 170 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com DQLMX0 DQ0 DQ1 DQ[0:7]/DM0/DQS0 DQ[8:15]/DM1/DQS1 DQLMX1 DQLMY0 DQLMY1 1 0 DQ0 - DQ1 represent data bytes 0 - 1. There are two DQLMs, one for each byte (16-bit interface). Each DQLM is the longest Manhattan distance of the byte; therefore: DQLM0 = DQLMX0 + DQLMY0 DQLM1 = DQLMX1 + DQLMY1 Table 5-60. DQS[x] and DQ[x] Routing Specification(1)(2) NO. MAX UNIT 1 DQ0 nominal length(3)(4) PARAMETER MIN TYP DQLM0 mils 2 (3)(5) DQ1 nominal length DQLM1 mils 3 DQ[x] skew(6) 25 mils 4 DQS[x] skew 5 mils 25 mils (6)(7) 5 DQS[x]-to-DQ[x] skew 6 Center-to-center DQ[x] to other DDR3 trace spacing(8)(9) 4w 7 Center-to-center DQ[x] to other DQ[x] trace spacing(8)(10) 3w 8 DQS[x] center-to-center spacing(11) 9 DQS[x] center-to-center spacing to other net(8) 4w (1) DQS[x] represents the DQS0 and DQS1 clock net classes, and DQ[x] represents the DQ0 and DQ1 signal net classes. (2) External termination disallowed. Data termination should use built-in ODT functionality. (3) DQLMn is the longest Manhattan distance of a byte. For definition, see Section 5.4.2.3.6.2 and Figure 5-61. (4) DQLM0 is the longest Manhattan length for the DQ0 net class. (5) DQLM1 is the longest Manhattan length for the DQ1 net class. (6) Length matching is only done within a byte. Length matching across bytes is neither required nor recommended. (7) Each DQS clock net class is length matched to its associated DQ signal net class. (8) Center-to-center spacing is allowed to fall to minimum for up to 1250 mils of routed length. (9) Other DDR3 trace spacing means signals that are not part of the same DQ[x] signal net class. (10) This applies to spacing within same DQ[x] signal net class. (11) DQS[x] pair spacing is set to ensure proper differential impedance. Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 171 PRODUCT PREVIEW Figure 5-61. DQLM for Any Number of Allowed DDR3 Devices AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.5 www.ti.com LCD Controller (LCDC) The LCD controller consists of two independent controllers, the raster controller and the LCD interface display driver (LIDD) controller. Each controller operates independently from the other and only one of them is active at any given time. • The raster controller handles the synchronous LCD interface. It provides timing and data for constant graphics refresh to a passive display. It supports a wide variety of monochrome and full-color display types and sizes by use of programmable timing controls, a built-in palette, and a gray-scale/serializer. Graphics data is processed and stored in frame buffers. A frame buffer is a contiguous memory block in the system. A built-in DMA engine supplies the graphics data to the raster engine which, in turn, outputs to the external LCD device. • The LIDD controller supports the asynchronous LCD interface. It provides full-timing programmability of control signals (CS, WE, OE, ALE) and output data. The maximum resolution for the LCD controller is 2048 x 2048 pixels. The maximum frame rate is determined by the image size in combination with the pixel clock rate. Table 5-61. LCD Controller Timing Conditions TIMING CONDITION PARAMETER MIN TYP MAX UNIT Output Condition PRODUCT PREVIEW CLOAD 5.5.1 Output load capacitance LIDD mode 5 60 pF Raster mode 3 30 pF LCD Interface Display Driver (LIDD Mode) Table 5-62. Timing Requirements for LCD LIDD Mode (see Figure 5-63 through Figure 5-71) NO. OPP100 PARAMETER 16 tsu(LCD_DATA-LCD_MEMORY_CLK) Setup time, LCD_DATA[15:0] valid before LCD_MEMORY_CLK high 17 th(LCD_MEMORY_CLK-LCD_DATA) 18 tt(LCD_DATA) MIN MAX UNIT 18 ns Hold time, LCD_DATA[15:0] valid after LCD_MEMORY_CLK high 0 ns Transition time, LCD_DATA[15:0] 1 3 pf Table 5-63. Switching Characteristics Over Recommended Operating Conditions for LCD LIDD Mode (see Figure 5-63 through Figure 5-71) NO. MIN MAX tc(LCD_MEMORY_CLK) Cycle time, LCD_MEMORY_CLK 2 tw(LCD_MEMORY_CLKH) Pulse duration, LCD_MEMORY_CLK high 0.45tc 0.55tc ns 3 tw(LCD_MEMORY_CLKL) Pulse duration, LCD_MEMORY_CLK low 0.45tc 0.55tc ns 4 td(LCD_MEMORY_CLK-LCD_DATAV) Delay time, LCD_MEMORY_CLK high to LCD_DATA[15:0] valid (write) 7 ns 5 td(LCD_MEMORY_CLK-LCD_DATAI) Delay time, LCD_MEMORY_CLK high to LCD_DATA[15:0] invalid (write) 0 6 td(LCD_MEMORY_CLK-LCD_AC_BIAS_EN) Delay time, LCD_MEMORY_CLK high to LCD_AC_BIAS_EN 0 6.8 ns 7 tt(LCD_AC_BIAS_EN) Transition time, LCD_AC_BIAS_EN 1 10 ns 8 td(LCD_MEMORY_CLK-LCD_VSYNC) Delay time, LCD_MEMORY_CLK high to LCD_VSYNC 0 7 ns 9 tt(LCD_VSYNC) Transition time, LCD_VSYNC 1 10 ns td(LCD_MEMORY_CLK-LCD_HYSNC) Delay time, LCD_MEMORY_CLK high to LCD_HSYNC 0 7 ns Peripheral Information and Timings 23.7 UNIT 1 10 172 OPP100 PARAMETER ns ns Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Table 5-63. Switching Characteristics Over Recommended Operating Conditions for LCD LIDD Mode (continued) (see Figure 5-63 through Figure 5-71) NO. OPP100 PARAMETER MIN MAX UNIT 11 tt(LCD_HSYNC) Transition time, LCD_HYSNC 1 10 ns 12 td(LCD_MEMORY_CLK-LCD_PCLK) Delay time, LCD_MEMORY_CLK high to LCD_PCLK 0 7 ns 13 tt(LCD_PCLK) Transition time, LCD_PCLK 1 10 ns 14 td(LCD_MEMORY_CLK-LCD_DATAZ) Delay time, LCD_MEMORY_CLK high to LCD_DATA[15:0] high-Z 0 7 ns 15 td(LCD_MEMORY_CLK-LCD_DATA) Delay time, LCD_MEMORY_CLK high to LCD_DATA[15:0] driven 0 7 ns 19 tt(LCD_MEMORY_CLK) Transition time, LCD_MEMORY_CLK 1 2.5 ns 20 tt(LCD_DATA) Transition time, LCD_DATA 1 10 ns W_SU (0 to 31) CS_DELAY (0 to 3) W_STROBE (1 to 63) W_HOLD (1 to 15) PRODUCT PREVIEW LCD_MEMORY_CLK 6 6 LCD_MEMORY_CLK (E1) 7 4 LCD_DATA[7:0] 5 Write Instruction 8 8 10 10 LCD_VSYNC (RS) 9 LCD_HSYNC (R/W) 6 6 11 LCD_AC_BIAS_EN (E0) 7 A. Hitachi mode performs asynchronous operations that do not require an external LCD_MEMORY_CLK. The first LCD_MEMORY_CLK waveform is only shown as a reference of the internal clock that sequences the other signals. The second LCD_MEMORY_CLK waveform is shown as E1 since the LCD_MEMORY_CLK signal is used to implement the E1 function in Hitachi mode. Figure 5-62. Command Write in Hitachi Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 173 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com W_SU (0 to 31) CS_DELAY (0 to 3) W_STROBE (1 to 63) W_HOLD (1 to 15) LCD_MEMORY_CLK 6 6 LCD_MEMORY_CLK (E1) 7 4 LCD_DATA[15:0] 5 Write Data 20 LCD_VSYNC (RS) 10 10 LCD_HSYNC (R/W) 11 6 6 LCD_AC_BIAS_EN (E0) 7 PRODUCT PREVIEW A. Hitachi mode performs asynchronous operations that do not require an external LCD_MEMORY_CLK. The first LCD_MEMORY_CLK waveform is only shown as a reference of the internal clock that sequences the other signals. The second LCD_MEMORY_CLK waveform is shown as E1 since the LCD_MEMORY_CLK signal is used to implement the E1 function in Hitachi mode. Figure 5-63. Data Write in Hitachi Mode R_SU (0 to 31) R_STROBE (1 to 63) R_HOLD (1 to 15) CS_DELAY (0 to 3) LCD_MEMORY_CLK 6 6 LCD_MEMORY_CLK (E1) 14 7 16 17 15 LCD_DATA[15:0] 8 Read Command 18 8 LCD_VSYNC (RS) 9 LCD_HSYNC (R/W) 6 6 LCD_AC_BIAS_EN (E0) 7 A. Hitachi mode performs asynchronous operations that do not require an external LCD_MEMORY_CLK. The first LCD_MEMORY_CLK waveform is only shown as a reference of the internal clock that sequences the other signals. The second LCD_MEMORY_CLK waveform is shown as E1 since the LCD_MEMORY_CLK signal is used to implement the E1 function in Hitachi mode. Figure 5-64. Command Read in Hitachi Mode 174 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com R_SU (0 to 31) R_STROBE (1 to 63) R_HOLD (1 to 15) CS_DELAY (0 to 3) LCD_MEMORY_CLK 6 6 LCD_MEMORY_CLK (E1) 14 7 16 17 15 LCD_DATA[15:0] Read Data 18 LCD_VSYNC (RS) LCD_HSYNC (R/W) 6 6 LCD_AC_BIAS_EN (E0) PRODUCT PREVIEW 7 A. Hitachi mode performs asynchronous operations that do not require an external LCD_MEMORY_CLK. The first LCD_MEMORY_CLK waveform is only shown as a reference of the internal clock that sequences the other signals. The second LCD_MEMORY_CLK waveform is shown as E1 since the LCD_MEMORY_CLK signal is used to implement the E1 function in Hitachi mode. Figure 5-65. Data Read in Hitachi Mode Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 175 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com W_HOLD (1−15) 1 W_SU (0−31) W_STROBE (1−63) 2 3 W_HOLD (1−15) W_SU (0−31) CS_DELAY (0−3) W_STROBE (1−63) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 19 6 6 6 6 4 5 LCD_MEMORY_CLK (CS1) Async Mode 7 4 LCD_DATA[15:0] 5 Write Address Write Data 20 6 6 6 6 10 10 LCD_AC_BIAS_EN (CS0) 7 PRODUCT PREVIEW 8 8 LCD_VSYNC (ALE) 9 10 10 LCD_HSYNC (DIR) 11 12 12 12 12 LCD_PCLK (EN) A. 13 Motorola mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-66. Micro-Interface Graphic Display Motorola Write 176 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com R_SU (0−31) W_HOLD (1−15) 1 W_SU (0−31) 2 3 W_STROBE (1−63) R_STROBE (1−63) CS_DELAY (0−3) R_HOLD (1−15) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 19 6 6 6 6 LCD_MEMORY_CLK (CS1) Async Mode 7 4 LCD_DATA[15:0] 5 16 14 17 15 Write Address 18 20 6 6 Read Data 6 6 LCD_AC_BIAS_EN (CS0) 8 PRODUCT PREVIEW 7 8 LCD_VSYNC (ALE) 9 10 10 LCD_HSYNC (DIR) 11 12 12 12 12 LCD_PCLK (EN) A. 13 Motorola mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-67. Micro-Interface Graphic Display Motorola Read Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 177 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com R_SU (0−31) 1 2 3 R_STROBE (1−63) R_HOLD (1−15) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 19 6 6 LCD_MEMORY_CLK (CS1) Async Mode 7 14 16 17 15 LCD_DATA[15:0] Read Status 18 6 6 LCD_AC_BIAS_EN (CS0) PRODUCT PREVIEW 7 8 8 LCD_VSYNC (ALE) 9 LCD_HSYNC (DIR) 12 12 LCD_PCLK (EN) 13 A. Motorola mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-68. Micro-Interface Graphic Display Motorola Status 178 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com W_HOLD (1−15) 1 W_SU (0−31) 2 3 W_HOLD (1−15) W_SU (0−31) W_STROBE (1−63) CS_DELAY (0−3) W_STROBE (1−63) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 19 6 6 6 6 5 4 5 LCD_MEMORY_CLK (CS1) Async Mode 7 4 LCD_DATA[15:0] Write Address Write Data 20 6 6 6 6 LCD_AC_BIAS_EN (CS0) 8 PRODUCT PREVIEW 7 8 LCD_VSYNC (ALE) 9 10 10 10 10 LCD_HSYNC (WS) 11 LCD_PCLK (RS) A. Intel mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-69. Micro-Interface Graphic Display Intel Write Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 179 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com R_SU (0−31) W_HOLD (1−15) 1 W_SU (0−31) W_STROBE (1−63) 2 3 R_STROBE (1−63) CS_DELAY (0−3) R_HOLD (1−15) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 6 6 19 6 6 LCD_MEMORY_CLK (CS1) Async Mode 7 4 LCD_DATA[15:0] 5 16 14 17 15 Write Address 18 20 6 6 Read Data 6 6 LCD_AC_BIAS_EN (CS0) 7 PRODUCT PREVIEW 8 8 LCD_VSYNC (ALE) 9 10 10 LCD_HSYNC (WS) 11 12 12 LCD_PCLK (RS) A. 13 Intel mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-70. Micro-Interface Graphic Display Intel Read 180 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com R_SU (0−31) 1 2 3 R_STROBE (1−63) R_HOLD (1−15) CS_DELAY (0−3) LCD_MEMORY_CLK (MCLK) Sync Mode 19 6 6 LCD_MEMORY_CLK (CS1) Async Mode 7 14 16 17 15 LCD_DATA[15:0] Read Status 18 6 6 LCD_AC_BIAS_EN (CS0) 8 PRODUCT PREVIEW 7 8 LCD_VSYNC (ALE) 9 LCD_HSYNC (WS) 12 12 LCD_PCLK (RS) 13 A. Intel mode can be configured to perform asynchronous operations or synchronous operations. When configured in asynchronous mode, LCD_MEMORY_CLK is not required, so it performs the CS1 function. When configured in synchronous mode, LCD_MEMORY_CLK performs the MCLK function. LCD_MEMORY_CLK is also shown as a reference of the internal clock that sequences the other signals. Figure 5-71. Micro-Interface Graphic Display Intel Status Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 181 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 5.5.2 www.ti.com LCD Raster Mode Table 5-64. Switching Characteristics Over Recommended Operating Conditions for LCD Raster Mode (see Figure 5-73 through Figure 5-76) NO. PARAMETER OPP50 MIN OPP100 MAX 7.9 MIN MAX 7.9 UNIT PRODUCT PREVIEW 1 tc(LCD_PCLK) Cycle time, pixel clock 2 tw(LCD_PCLKH) Pulse duration, pixel clock high 0.45tc 0.55tc 0.45tc 0.55tc ns 3 tw(LCD_PCLKL) Pulse duration, pixel clock low 0.45tc 0.55tc 0.45tc 0.55tc ns 4 td(LCD_PCLK-LCD_DATAV) Delay time, LCD_PCLK to LCD_DATA[23:0] valid (write) 1 ns 5 td(LCD_PCLK-LCD_DATAI) Delay time, LCD_PCLK to LCD_DATA[23:0] invalid (write) 6 td(LCD_PCLK-LCD_AC_BIAS_EN) Delay time, LCD_PCLK to LCD_AC_BIAS_EN 7 tt(LCD_AC_BIAS_EN) Transition time, LCD_AC_BIAS_EN 8 td(LCD_PCLK-LCD_VSYNC) Delay time, LCD_PCLK to LCD_VSYNC 9 tt(LCD_VSYNC) Transition time, LCD_VSYNC 10 td(LCD_PCLK-LCD_HSYNC) Delay time, LCD_PCLK to LCD_HSYNC -1.5 1 11 tt(LCD_HSYNC) Transition time, LCD_HSYNC 0.5 2.4 12 tt(LCD_PCLK) Transition time, LCD_PCLK 0.5 2.4 13 tt(LCD_DATA) Transition time, LCD_DATA 0.5 2.4 1 -1.5 ns -1 ns -1.5 1 -1 1 ns 0.5 2.4 0.5 2.4 ns -1.5 1 -1 1 ns 0.5 2.4 0.5 2.4 ns -1 1 ns 0.5 2.4 ns 0.5 2.4 ns 0.5 2.4 ns Frame-to-frame timing is derived through the following parameters in the LCD (RASTER_TIMING_1) register: • Vertical front porch (VFP) • Vertical sync pulse width (VSW) • Vertical back porch (VBP) • Lines per panel (LPP_B10 + LPP) Line-to-line timing is derived through the following parameters in the LCD (RASTER_TIMING_0) register: • Horizontal front porch (HFP) • Horizontal sync pulse width (HSW) • Horizontal back porch (HBP) • Pixels per panel (PPLMSB + PPLLSB) LCD_AC_BIAS_EN timing is derived through the following parameter in the LCD (RASTER_TIMING_2) register: • AC bias frequency (ACB) The display format produced in raster mode is shown in Figure 5-72. An entire frame is delivered one line at a time. The first line delivered starts at data pixel (1, 1) and ends at data pixel (P, 1). The last line delivered starts at data pixel (1, L) and ends at data pixel (P, L). The beginning of each new frame is denoted by the activation of I/O signal LCD_VSYNC. The beginning of each new line is denoted by the activation of I/O signal LCD_HSYNC. 182 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Data Pixels (From 1 to P) 1, 1 2, 1 1, 2 2, 2 P−2, 1 3, 1 P−1, 1 P, 1 P−1, 2 P, 2 1, 3 Data Lines (From 1 to L) P, 3 LCD 1, L−2 1, L−1 2, L−1 1, L 2, L P−2, L 3, L P−1, L−1 P, L−1 P−1, L P, L PRODUCT PREVIEW P, L−2 Figure 5-72. LCD Raster-Mode Display Format Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 183 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Frame Time VBP (0 to 255) VSW (1 to 64) Line Time LPP_B10 + LPP VFP (1 to 2048) (0 to 255) VSW (1 to 64) LCD_HSYNC LCD_VSYNC LCD_DATA[23:0] 1, 1 P, 1 1, 2 P, 2 1, L-1 P, L-1 1, L P, L PRODUCT PREVIEW LCD_AC_BIAS_EN (ACTVID) 10 10 LCD_HSYNC 11 LCD_PCLK LCD_DATA[23:0] 1, 1 2, 1 1, 2 P, 1 2, 2 P, 2 LCD_AC_BIAS_EN (ACTVID) PPLMSB + PPLLSB HFP HSW HBP PPLMSB + PPLLSB 16 × (1 to 2048) (1 to 256) (1 to 64) (1 to 256) 16 × (1 to 2048) Line 1 Line 2 Figure 5-73. LCD Raster-Mode Active 184 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com Frame Time VBP = 0 VFP = 0 VSW = 1 LPP_B10 + LPP (1 to 2048) Line Time LCD_HSYNC LCD_VSYNC 1, L Data LCD_DATA[7:0] 1, L: P, L 1, 1: P, 1 1, 2: P, 2 1, 3: P, 3 1, 4: P, 4 1, 5: P, 5 1, 6: P, 6 1, L P, L 1, L−1 P, L−1 1, L−4 P, L−4 1, L−3 P, L−3 1, L−2 P, L−2 1, 1 P, 1 1, 2 P, 2 1, L−1 P, L−1 ACB ACB (0 to 255) (0 to 255) 10 PRODUCT PREVIEW LCD_AC_BIAS_EN 10 LCD_HSYNC 11 LCD_PCLK LCD_DATA[7:0] A. 1, 5 P, 5 2, 5 1, 6 2, 6 P, 6 PPLMSB + PPLLSB HFP HSW HBP PPLMSB + PPLLSB 16 x (1 to 2048) (1 to 256) (1 to 64) (1 to 256) 16 x (1 to 2048) Line 6 Line 5 The dashed portion of LCD_PCLK is only shown as a reference of the internal clock that sequences the other signals. Figure 5-74. LCD Raster-Mode Passive Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 185 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 6 LCD_AC_BIAS_EN 7 8 LCD_VSYNC 9 10 10 LCD_HSYNC 11 1 2 3 LCD_PCLK (passive mode) 5 4 PRODUCT PREVIEW LCD_DATA[7:0] (passive mode) 1, L 2, L P, L 1, 1 2, 1 P, 1 1 2 3 LCD_PCLK (active mode) 5 4 LCD_DATA[23:0] (active mode) VBP = 0 VFP = 0 VWS = 1 1, L 2, L P, L PPLMSB + PPLLSB 16 x (1 to 2048) HFP (1 to 256) HSW (1 to 64) HBP (1 to 256) Line L A. PPLMSB + PPLLSB 16 x (1 to 2048) Line 1 (Passive Only) The dashed portion of LCD_PCLK is only shown as a reference of the internal clock that sequences the other signals. Figure 5-75. LCD Raster-Mode Control Signal Activation 186 Peripheral Information and Timings Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 6 LCD_AC_BIAS_EN 8 LCD_VSYNC 10 10 LCD_HSYNC 11 1 2 3 LCD_PCLK (passive mode) 4 1, 1 P, 1 2, 1 1, 2 2, 2 1, 1 2, 1 5 P, 2 1 2 3 LCD_PCLK (active mode) 4 LCD_DATA[23:0] (active mode) VBP = 0 VFP = 0 VWS = 1 PPLMSB + PPLLSB 16 x (1 to 2048) HFP (1 to 256) HSW (1 to 64) HBP (1 to 256) PPLMSB + PPLLSB Line 1 A. 5 P, 1 16 x (1 to 2048) Line 1 for active Line 2 for passive The dashed portion of LCD_PCLK is only shown as a reference of the internal clock that sequences the other signals. Figure 5-76. LCD Raster-Mode Control Signal Deactivation Peripheral Information and Timings Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 187 PRODUCT PREVIEW LCD_D[7:0] (passive mode) AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 6 Device and Documentation Support 6.1 6.1.1 Device Support Development Support TI offers an extensive line of development tools, including tools to evaluate the performance of the processors, generate code, develop algorithm implementations, and fully integrate and debug software and hardware modules. The tool's support documentation is electronically available within the Code Composer Studio™ Integrated Development Environment (IDE). The following products support development of AM335x device applications: Software Development Tools: Code Composer Studio™ Integrated Development Environment (IDE): including Editor C/C++/Assembly Code Generation, and Debug plus additional development tools Scalable, Real-Time Foundation Software (DSP/BIOS™), which provides the basic run-time target software needed to support any AM335x device application. DSP/BIOS™ Hardware Development Tools: Extended Development System (XDS™) Emulator XDS™ PRODUCT PREVIEW For a complete listing of development-support tools for the AM335x microprocessor platform, visit the Texas Instruments website at www.ti.com. For information on pricing and availability, contact the nearest TI field sales office or authorized distributor. 6.1.2 Device Nomenclature To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all microprocessors (MPUs) and support tools. Each device has one of three prefixes: X, P, or null (no prefix) (e.g., XAM3358ZCE). Texas Instruments recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes (TMDX) through fully qualified production devices/tools (TMDS). Device development evolutionary flow: X Experimental device that is not necessarily representative of the final device's electrical specifications and may not use production assembly flow. P Prototype device that is not necessarily the final silicon die and may not necessarily meet final electrical specifications. null Production version of the silicon die that is fully qualified. Support tool development evolutionary flow: TMDX Development-support product that has not yet completed Texas Instruments internal qualification testing. TMDS Fully-qualified development-support product. X and P devices and TMDX development-support tools are shipped against the following disclaimer: "Developmental product is intended for internal evaluation purposes." Production devices and TMDS development-support tools have been characterized fully, and the quality and reliability of the device have been demonstrated fully. TI's standard warranty applies. Predictions show that prototype devices (X or P) have a greater failure rate than the standard production devices. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used. 188 Device and Documentation Support Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type (for example, ZCE), the temperature range (for example, blank is the default commercial temperature range), and the device speed range, in megahertz (for example, 27 is 275-MHz). Figure 6-1 provides a legend for reading the complete device name for any AM335x device. For orderable part numbers of AM335x devices in the ZCE and ZCZ package types, see the Package Option Addendum of this document, the TI website (www.ti.com), or contact your TI sales representative. For additional description of the device nomenclature markings on the die, see the AM335x ARM Cortex-A8 Microprocessors (MPUs) Silicon Errata (literature number SPRZ360). AM3358 PREFIX X = Experimental device Blank = Qualified device (A) ZCE ( ) ( ) TEMPERATURE RANGE Blank = 0°C to 90°C (commercial junction temperature) A = -40°C to 105°C (extended temperature) D = -40°C to 90°C (industrial temperature) (B) PACKAGE TYPE ZCE = 298-pin plastic BGA, with Pb-Free solder balls ZCZ = 324-pin plastic BGA, with Pb-Free solder balls SILICON REVISION Blank = silicon revision 1.0 B. ) DEVICE SPEED RANGE 27 = 275-MHZ Cortex-A8 50 = 500-MHZ Cortex-A8 60 = 600-MHZ Cortex-A8 72 = 720-MHz Cortex-A8 DEVICE ARM Cortex-A8 MPU: AM3352 AM3354 AM3356 AM3357 AM3358 AM3359 A. ( The AM3358 device shown in this device nomenclature example is one of several valid part numbers for the AM335x family of devices. For orderable device part numbers, see the Package Option Addendum of this document. BGA = Ball Grid Array. Figure 6-1. AM335x Device Nomenclature 6.2 6.2.1 Documentation Support Related Documentation from Texas Instruments The following documents describe the AM335x MPU. Copies of these documents are available on the Internet at www.ti.com. Tip: Enter the literature number in the search box. The current documentation that describes the AM335x MPU, related peripherals, and other technical collateral, is available in the product folder at: www.ti.com. 6.2.2 SPRUH73 AM335x ARM Cortex-A8 Microprocessors (MPUs) Technical Reference Manual. Collection of documents providing detailed information on the AM335x device including power, reset, and clock control, interrupts, memory map, and switch fabric interconnect. Detailed information on the microprocessor unit (MPU) subsystem as well as a functional description of the peripherals supported on AM335x devices is also included. SPRZ360 AM335x ARM Cortex-A8 Microprocessors (MPUs) Silicon Errata. Describes the known exceptions to the functional specifications for the AM335x ARM Cortex-A8 Microprocessors. Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. TI Embedded Processors Wiki Texas Instruments Embedded Processors Wiki. Established to help developers get started with Embedded Processors from Texas Instruments and to foster Device and Documentation Support Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 189 PRODUCT PREVIEW X AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com innovation and growth of general knowledge about the hardware and software surrounding these devices. 6.2.3 Related Documentation from Other Sources The following documents are related to the AM335x MPU. Copies of these documents can be obtained directly from the internet or from your Texas Instruments representative. Cortex-A8 Technical Reference Manual. This is the technical reference manual for the Cortex-A8 processor. A copy of this document can be obtained via the internet at http://infocenter.arm.com. To determine the revision of the Cortex-A8 core used on your device, see the AM335x ARM Cortex-A8 Microprocessors (MPUs) Silicon Errata (literature number SPRZ360). ARM Core Cortex™-A8 (AT400/AT401) Errata Notice. Provides a list of advisories for the different revisions of the Cortex-A8 processor. Contact your TI representative for a copy of this document. To determine the revision of the Cortex-A8 core used on your device, see the AM335x ARM Cortex-A8 Microprocessors (MPUs) Silicon Errata (literature number SPRZ360). PRODUCT PREVIEW 190 Device and Documentation Support Copyright © 2011–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 AM3359, AM3358, AM3357 AM3356, AM3354, AM3352 SPRS717B – OCTOBER 2011 – REVISED JANUARY 2012 www.ti.com 7 Mechanical Packaging and Orderable Information 7.1 Thermal Data for ZCE and ZCZ Packages Table 7-1 provides thermal characteristics for the packages used on this device. NOTE Table 7-1 provides simulation data and may not represent actual use-case values. NAME DESCRIPTION ΘJC ΘJB ΘJA ZCZ (°C/W) (2) Junction-to-case (1S0P) (3) N/A 10.3 10.2 Junction-to-board (2S2P) (3) N/A 11.6 12.1 0.0 24.7 24.2 1.0 20.5 20.1 2.0 19.7 19.3 3.0 19.2 18.8 0.0 0.4 0.3 1.0 0.6 0.6 2.0 0.7 0.7 (3) Junction-to-package top (2S2P) (3) Junction-to-board (2S2P) (3) ΨJB 7.2 ZCE (°C/W) (2) Junction-to-free air (2S2P) ΨJT (1) (2) (3) AIR FLOW (1) 3.0 0.9 0.8 0.0 11.9 12.7 1.0 11.7 12.3 2.0 11.7 12.3 3.0 11.6 12.2 PRODUCT PREVIEW Table 7-1. Thermal Resistance Characteristics (PBGA Package) [ZCE and ZCZ] m/s = meters per second. °C/W = degress celsius per watt. The board types are defined by JEDEC (reference JEDEC standard JESD51-9, Test Board for Area Array Surface Mount Package Thermal Measurements). Via Channel The ZCE package has been specially engineered with Via Channel™ technology. This allows larger than normal PCB via and trace sizes and reduced PCB signal layers to be used in a PCB design with the 0.65-mm pitch package, and substantially reduces PCB costs. It allows PCB routing in only two signal layers (four layers total) due to the increased layer efficiency of the Via Channel™ BGA technology. Via Channel™ technology implemented on the ZCE package makes it possible to build an AM335x-based product with a 4-layer PCB, but a 4-layer PCB may not meet system performance goals. Therefore, system performance using a 4-layer PCB design must be evaluated during product design. 7.3 Packaging Information The following packaging information and addendum reflect the most current data available for the designated device(s). This data is subject to change without notice and without revision of this document. The figures below show the package drawings for the ZCE and ZCZ package options. Mechanical Packaging and Orderable Information Submit Documentation Feedback Product Folder Link(s): AM3359 AM3358 AM3357 AM3356 AM3354 AM3352 Copyright © 2011–2012, Texas Instruments Incorporated 191 PACKAGE OPTION ADDENDUM www.ti.com 5-Mar-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) AM3352ZCE27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3352ZCE50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3352ZCED27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3352ZCED50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3352ZCZ27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3352ZCZ60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3352ZCZ72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3352ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCE27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3354ZCE50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3354ZCED27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3354ZCED50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3354ZCZ27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCZ60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCZ72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCZD60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3354ZCZD72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCE27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3356ZCE50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3356ZCED27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3356ZCED50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3356ZCZ27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCZ60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCZ72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCZD60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3356ZCZD72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3357ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3357ZCZD60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI Addendum-Page 1 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 5-Mar-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) AM3357ZCZD72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3358ZCE27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3358ZCE50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3358ZCED27 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3358ZCED50 PREVIEW NFBGA ZCE 298 TBD Call TI Call TI AM3358ZCZ27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3358ZCZ60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3358ZCZ72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3358ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3358ZCZD60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3359ZCZD27 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3359ZCZD60 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI AM3359ZCZD72 PREVIEW NFBGA ZCZ 324 TBD Call TI Call TI XAM3358ZCE ACTIVE NFBGA ZCE 298 1 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR XAM3359ZCZ ACTIVE NFBGA ZCZ 324 1 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 5-Mar-2012 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated