IN-P32TATRGB Top View SMD LED 3528 PLCC Type Features Description • 3528 1.9mm SMD LED • High Brightness • AlInGaP / InGaN Technology • Small package • High reliability • Clear Lens The IN-P32TATRGB is a tri-color 3528 package with versatile design capabilities. It is a PLCC type LED which can be used in various applications. Recommended Solder Pattern Applications • Consumer Electronics • Wearables • Automobile After Market • Industrial Equipment Figure 1. IN-P32TATRGB Solder Pattern Package Dimensions in mm Figure 2. IN-P32TATRGB Package Dimensions Inolux Corporation Proprietary & Confidential May 12, 2017 Page 1 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Absolute Maximum Rating at 25oC (Note 1) Product Emission Color Pd (mW) IF (mA) IFP* (mA) Red 70 30 70 Green 90 30 100 Blue 90 30 100 IN-P32TATRGB VR (V) TOP (oC) 5 -30 C~+85 C o TST (oC) o o o -40 C~+90 C Notes 1. Condition for IFP is pulse of 1/10 duty and 0.1msec width ESD Precaution ATTENTION: Electrostatic Discharge (ESD) protection The symbol above denotes that ESD precaution is needed. ESD protection for GaP and AlGaAs based chips is necessary even though they are relatively safe in the presence of low static-electric discharge. Parts built with AlInGaP, GaN, or/and InGaN based chips are STATIC SENSITIVE devices. ESD precaution must be taken during design and assembly. If manual work or processing is needed, please ensure the device is adequately protected from ESD during the process. Please be advised that normal static precautions should be taken in the handling and assembly of this device to prevent damage or degradation which may be induced by electrostatic discharge (ESD). Electrical Characteristics T A = 25°C (Note 1) VF(V) Product IN-P32TATRGB Emission Color IF(mA) Red Viewing λ(nm) Angel I*V(mcd) typ. max λD λP △λ 2θ1/2 typ. 20 2.2 2.6 624 630 20 120 280 Green 20 3.2 3.6 525 530 35 120 900 Blue 20 3.2 3.6 468 470 30 120 300 Notes 1. Performance guaranteed only under conditions listed in above tables. Inolux Corporation Proprietary & Confidential May 12, 2017 Page 2 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Typical Characteristic Curves – YG, Y, A, R Inolux Corporation Proprietary & Confidential May 12, 2017 Page 3 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Typical Characteristic Curves – B, G, W Inolux Corporation Proprietary & Confidential May 12, 2017 Page 4 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Typical Characteristic Curves – Radiation Pattern Ordering Information Product Emission Color IN-P32TATRGB Red Green Blue Inolux Corporation Proprietary & Confidential Test Current IF (mA) Luminous Intensity IV (mcd) (Typ.) Forward Voltage VF (V) (Typ.) Orderable Part Number 280 900 300 2.2 3.2 3.2 IN-P32TATRGB 20 May 12, 2017 Page 5 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Label Specifications Inolux P/N: I N - P Material Inolux SMD P = PLCC Type 3 2 Package T A Variation 32TA = 3.5 x 2.8 x 1.9mm T R G B - Orientation Current Lens Color Chip Type T = Top Mount (Blank) = 20mA (Blank) = Clear R=630nm G=530nm B=470nm (blank) = Standard X X X X Customized Stamp-off Lot No.: Z Internal Tracker Inolux Corporation Proprietary & Confidential 2 0 1 7 Year (2017, 2018, …..) 01 24 001 Month Date Serial May 12, 2017 Page 6 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Packaging Information: 2000pcs Per Reel Tape Dimension Reel Dimension Inolux Corporation Proprietary & Confidential May 12, 2017 Page 7 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Packing Dimension 5 boxes per carton are available depending on shipment quantity. Specification Material Quantity Carrier tape Per EIA 481-1A specs Conductive black tape 2000pcs per reel Reel Per EIA 481-1A specs Conductive black Label IN standard Paper Packing bag 220x240mm Aluminum laminated bag/ no-zipper One reel per bag Carton IN standard Paper Non-specified Others: Each immediate box consists of 5 reels. The 5 reels may not necessarily have the same lot number or the same bin combinations of Iv, λD and Vf. Each reel has a label identifying its specification; the immediate box consists of a product label as well. Inolux Corporation Proprietary & Confidential May 12, 2017 Page 8 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Dry Pack All SMD optical devices are MOISTURE SENSITIVE. Avoid exposure to moisture at all times during transportation or storage. Every reel is packaged in a moisture protected anti-static bag. Each bag is properly sealed prior to shipment. Upon request, a humidity indicator will be included in the moisture protected anti-static bag prior to shipment. The packaging sequence is as follows: Reflow Soldering • Recommended tin glue specifications: melting temperature in the range of 178~192 OC • The recommended reflow soldering profile is as follows (temperatures indicated are as measured on the surface of the LED resin): Lead-free Solder Profile Inolux Corporation Proprietary & Confidential May 12, 2017 Page 9 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Precautions • • • • • • Avoid exposure to moisture at all times during transportation or storage. Anti-Static precaution must be taken when handling GaN, InGaN, and AlInGaP products. It is suggested to connect the unit with a current limiting resistor of the proper size. Avoid applying a reverse voltage. Avoid operation beyond the limits as specified by the absolute maximum ratings. Avoid direct contact with the surface through which the LED emits light. If possible, assemble the unit in a clean room or dust-free environment. Reworking • • • Rework should be completed within 5 seconds under 260 OC. The iron tip must not come in contact with the copper foil. Twin-head type is preferred. Cleaning Following are cleaning procedures after soldering: • An alcohol-based solvent such as isopropyl alcohol (IPA) is recommended. • Temperature x Time should be 50oC x 30sec. or <30oC x 3min • Ultra sonic cleaning: < 15W/ bath; bath volume ≤ 1liter • Curing: 100 OC max, <3min Cautions of Pick and Place • • • Avoid stress on the resin at elevated temperature. Avoid rubbing or scraping the resin by any object. Electro-static may cause damage to the component. Please ensure that the equipment is properly grounded. Use of an ionizer fan is recommended. Inolux Corporation Proprietary & Confidential May 12, 2017 Page 10 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Reliability Item Precondition Frequency/ lots/ samples/ failures For all reliability monitoring tests according to JEDEC Level 2 1Q/ 1/ 22/ 0 Solderability Standards Reference J-STD-020 CNS-554 1.) Baking at 85°C for 24hrs 2.) Moisture storage at 85°C/ 60% R.H. for 168hrs Accelerated aging 155°C/ 24hrs Tinning speed: 2.5+0.5cm/s Tinning: A: 215°C/ 3+1s or B: 260°C/ 10+1s Dipping soldering terminal only Soldering bath temperature A: 260+/-5°C; 10+/-1s B: 350+/-10°C; 3+/-0.5s 1.) Precondition: 85°C bakin g for 24hrs 85°C/ 60%R.H. for 168hrs 2.) Tamb25°C; IF=20mA; duration 1000hrs Tamb: 85°C Humidity: 85% R.H., IF=5mA Duration: 1000hrs Tamb: 55°C IF=20mA Duration: 1000hrs Tamb25°C, If=20mA,, Ip=100mA, Duty cycle=0.125 (tp=125μs,T=1sec) Duration 500hrs) A cycle: -40 degree C 15min; +85 degree C 15min Thermal steady within 5 min.. 300 cycles 2 chamber/ Air-to-air type 60+3°C 90+5/-10% R.H. for 500hrs 100+10°C for 500hrs CNS-6118 -40+5°C for 500hrs JESD22-B102-B And CNS-5068 CNS-5067 Resistance to soldering heat 1Q/ 1/ 40/ 0 CNS-11829 Operating life test High humidity, 1Q/ 1/ 45/ 0 high temperature bias 1Q/ 1/ 20 High temperature bias JESD-A101-B IN specs. 1Q/ 1/ 40/ 0 Pulse life test 1Q/ 1/ 76/ 0 Temperature cycle High humidity 1Q/ 1/ 40/ 0 storage test High temperature 1Q/ 1/ 40/ 0 storage test Low temperature 1Q/ 1/ 40/ 0 storage test Inolux Corporation Proprietary & Confidential Conditions JESD-A104-A IEC 68-2-14, Nb CNS-6117 May 12, 2017 Page 11 www.inolux-corp.com IN-P32TATRGB Top View SMD LED 3528 PLCC Type Revision History Changes since last revision Initial Release Page Version No. V1.0 Revision Date 05-12-2017 DISCLAIMER INOLUX reserves the right to make changes without further notice to any products herein to improve reliability, function or design. INOLUX does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. LIFE SUPPORT POLICY INOLUX’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of INOLUX or INOLUX CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Inolux Corporation Proprietary & Confidential May 12, 2017 Page 12 www.inolux-corp.com