LED Lamp GL5❏❏43 series ø5mm(T-1 3/4), Cylinder Type, Colorless Transparency LED Lamps for Indicator GL5❏❏43 series ■ Outline Dimensions (Ta=25˚C) ø4.8±0.15 Protruded resin 1.5MAX -20˚ -10˚ +20˚ +30˚ +40˚ Relative luminous intensity(%) 1.0 (Tie-bar cut) -50˚ 23.0MIN -60˚ 0.5±0.1 0˚ 100 +10˚ -40˚ 12.8±0.5 7.8 -30˚ 9.0 Colorless transparency ■ Directive Characteristics (Unit : mm) -70˚ 80 +50˚ 60 +60˚ 40 +70˚ 20 -80˚ +80˚ -90˚ +90˚ Single Color (1.0) 0 1 ø5.75 0.5±0.1 2.54NOM ±0.2 2.4 2 Pin connections 1 Anode 2 Cathode Unspecified tolerance:±0.2 ■ Absolute Maximum Ratings Model No. Emitting color GL5HD43 GL5HS43 GL5HY43 GL5EG43 GL5KG43 Red Sunset orange Yellow Yellow-green Green Material GaAsP on GAP GaAsP on GAP GaAsP on GAP GaP GaP (Ta=25˚C) Power dissipation Forward current Peak forward current P IF IFM*1 (mW) (mA) (mA) 84 84 84 84 84 30 30 30 30 30 Derating factor Reverse voltage Operating temperature Storage temperature (mA/˚C) VR Topr Tstg (V) (˚C) (˚C) DC Pulse 50 50 50 50 50 0.40 0.40 0.40 0.40 0.40 0.67 0.67 0.67 0.67 0.67 -25 to +85 -25 to +85 -25 to +85 -25 to +85 -25 to +85 5 5 5 5 5 Soldering temperature Tsol*2 (˚C) -25 to +100 -25 to +100 -25 to +100 -25 to +100 -25 to +100 260 260 260 260 260 *1 Duty ratio=1/10, Pulse width=0.1ms *2 5s or less(At the position of 1.6mm or more from the bottom face of resin package) ■ Electro-optical Characteristics Lens type Model No. GL5HD43 GL5HS43 Colorless GL5HY43 transparency GL5EG43 GL5KG43 Notice Internet Forward voltage VF(V) TYP 2.0 2.0 2.0 2.1 2.1 MAX 2.8 2.8 2.8 2.8 2.8 (Ta=25˚C) Peak emission wavelength λp(nm) TYP IF (mA) 635 610 585 565 555 20 20 20 20 20 Luminous intensity IF IV(mcd) (mA) TYP 300 250 250 300 120 20 20 20 20 20 Spectrum radiation bandwidth IF ∆λ(nm) (mA) TYP 35 35 30 30 30 20 20 20 20 20 Reverse current VR IR(µA) (V) MAX 10 10 10 10 10 4 4 4 4 4 Page for characteristics (MHZ) diagrams Terminal capacitance Ct(pF) TYP 20 15 35 35 35 1 1 1 1 1 100 100 101 102 102 In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/ 57 Characteristics Diagrams PR,P series Forward Current Derating Curve Forward Current vs. Forward Voltage(Note) 60 Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 (Ta=25˚C) 1000 500 50 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 Ambient temperature Ta(˚C) 1.6 1.8 2.0 2.2 2.4 -20 2.6 0 Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current (Ta=25˚C) 1000 60 20 Ambient temperature Ta(˚C) Forward voltage VF(V) (Ta=25˚C) 500 500 200 200 40 30 20 Peak forward current IFM(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 5.0 100 50 20 10 5.0 10 2.0 0 -25 0 25 50 75 85 100 1.0 0.1 125 2.0 1.0 0.2 0.5 1 2 5 10 20 1/50 50 1/20 Forward current IF(mA) Ambient temperature Ta(˚C) 1/10 1/5 1/2 1 Duty ratio DR HD,D series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current (Ta=25˚C) 1000 60 20 Ambient temperature Ta(˚C) (Ta=25˚C) 500 500 300 40 30 20 200 Peak forward current IF(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 25 50 75 85 Ambient temperature Ta(˚C) 100 125 30 10 2.0 0 50 5.0 10 0 -25 100 1.0 0.1 5 0.2 0.5 1 2 5 10 20 Forward current IF(mA) 50 1/50 1/20 1/10 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) 100 Notice Internet In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/ Characteristics Diagrams HS,S series Forward Current Derating Curve Forward Current vs. Forward Voltage(Note) 60 Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 50 500 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 40 20 10 5 3 2 10 0 25 50 75 85 100 0.5 1.0 125 200 100 50 20 1 0 -25 (IF=20mA) 1000 10 1.2 1.4 Ambient temperature Ta(˚C) 1.6 1.8 2.0 2.2 2.4 -20 0 Forward voltage VF(V) 60 500 50 200 40 60 80 100 Duty Ratio vs. Peak Forward Current Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 20 Ambient temperature Ta(˚C) (Ta=25˚C) (Ta=25˚C) 500 40 30 20 100 Peak forward current IF(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 300 50 20 10 5 10 0 25 50 75 85 100 1 0.1 125 50 30 10 2 0 -25 100 5 0.2 0.5 1 2 5 10 20 1/50 50 1/20 1/10 1/5 1/2 1 Duty ratio DR Forward current IF(mA) Ambient temperature Ta(˚C) HY,H series Forward Current Derating Curve Forward Current vs. Forward Voltage(Note) 60 Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 Ambient temperature Ta(˚C) 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) (Ta=25˚C) 1000 60 40 60 80 100 120 Duty Ratio vs. Peak Forward Current Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 20 Ambient temperature Ta(˚C) (Ta=25˚C) 500 500 300 40 30 20 200 Peak forward current IF(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 25 50 75 85 Ambient temperature Ta(˚C) 100 125 30 10 2.0 0 50 5.0 10 0 -25 100 Characteristics Diagrams 0 -25 1.0 0.1 5 0.2 0.5 1 2 5 10 20 Forward current IF(mA) 50 1/50 1/20 1/10 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) Notice Internet In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/ 101 Characteristics Diagrams EG,E,F,C series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current Luminous Intensity vs. Forward Current(Note) 60 20 Ambient temperature Ta(˚C) (Ta=25˚C) 1000 (Ta=25˚C) 500 500 300 40 30 20 200 Peak forward current IF(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 25 50 75 85 100 1.0 0.1 125 30 10 2.0 0 50 5.0 10 0 -25 100 5 0.2 0.5 Ambient temperature Ta(˚C) 1 2 5 10 20 1/50 50 1/20 1/10 1/5 1/2 1 Duty ratio DR Forward current IF(mA) KG,K series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Peak Forward Current Derating Curve Luminous Intensity vs. Forward Current(Note) 60 20 40 60 80 100 120 Ambient temperature Ta(˚C) Duty Ratio vs. Peak Forward Current (Ta=25˚C) 1000 (Ta=25˚C) 500 500 300 40 30 20 200 Peak forward current IF(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 25 50 75 85 Ambient temperature Ta(˚C) 100 125 30 10 2.0 0 50 5.0 10 0 -25 100 1.0 0.1 5 0.2 0.5 1 2 5 10 20 Forward current IF(mA) 50 1/50 1/20 1/10 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) 102 Notice Internet In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/ Taping Specifications ■ General Description Sharp can supply tape-packaged LED lamps for automatic mounting. They will contribute to the high-efficiency mounting, high-precision, power saving. Please confirm before use because some products are not available in taping package. ■ Taping specification(Unit : mm, TYP. value) P Forming type P Straight type F W WO W WO H HO H F DO DO PO Parameter PO Symbol A B D Parameter 23.35 19.5 21.5 Case end height H 16.0 Lead clinch height HO 18.0 Tape width W WO 13.0 Adhesive tape width P 12.7 Product pitch PO 12.7 Sprocket hole pitch 5.0 Lead pitch Case end height H Lead clinch height HO Tape width W Adhesive tape width Product pitch Sprocket hole pitch Lead pitch F Sprocket hole diameter DO Sprocket hole diameter ø4.0 Symbol P W 18.0 23.35 ----18.0 WO 13.0 P 12.7 PO 12.7 F 2.54 DO ø4.0 P Dichromatic emission type Taping Specifications WO W H F1 F2 DO PO Parameter H Lead clinch height HO Tape width W Adhesive tape width Product pitch Sprocket hole pitch Lead pitch Sprocket hole diameter Notice Internet Symbol Case end height Size (mm) 19.5 ---18.0 WO 13.0 P 12.7 PO 12.7 F1 , F2 2.54 DO ø4.0 In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/ 105 NOTICE ¡The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ¡Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reser ves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. ¡Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). ¡If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. ¡This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in par t, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. ¡Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 108