LM3691 High Accuracy, Miniature 1A, Step-Down DC-DC Converter for Portable Applications General Description Features The LM3691 step-down DC-DC converter is optimized for powering ultra-low voltage circuits from a single Li-Ion cell or 3 cell NiMH/NiCd batteries. It provides up to 1A load current, over an input voltage range from 2.3V to 5.5V. There are several different fixed voltage output options available. LM3691 has a mode-control pin that allows the user to select Forced PWM mode or ECO mode that changes modes between gated PWM mode and PWM automatically depending on the load. In ECO, LM3691 offers superior efficiency and very low Iq under light load conditions. ECO mode extends the battery life through reduction of the quiescent current during light load conditions and system standby. The LM3691 is available in a 6–bump micro SMD package. Only three external surface-mount components, a 1μH inductor, a 4.7 μF input capacitor and a 4.7μF output capacitor, are required. ■ ■ ■ ■ ■ ■ ■ ■ ■ VOUT = 0.75V to 1.8V ±1% DC output voltage precision 2.3 ≤ VIN ≤ 5.5V 4 MHz switching frequency 64 μA (typ.) quiescent current in ECO mode 1A maximum load capability Automatic ECO/PWM mode switching Mode Pin to select ECO/Forced PWM mode 1 μH inductor, 4.7 μF input capacitor (0603(1608) case size) and 4.7 μF output capacitor (0603(1608) case size) ■ Current overload and thermal shutdown protections ■ Only three tiny surface-mount external components required (solution size less than 15 mm2) Applications ■ ■ ■ ■ Mobile Phones Hand-Held Radios MP3 players Portable Hard Disk Drives Efficiency vs. Output Current (VOUT = 1.8V, ECO Mode) Typical Application Circuit 30013430 FIGURE 1. Typical Application Circuit 30013454 © 2008 National Semiconductor Corporation 300134 www.national.com LM3691 High Accuracy, Miniature 1A, Step-Down DC-DC Converter for Portable Applications June 11, 2008 LM3691 Connection Diagram and Package Mark Information 30013406 FIGURE 2. 6-Bump Thin Micro SMD Package, Large Bump NS Package Number TLA06LCA Note: The actual physical placement of the package marking will vary from part to part. The package marking “X” designates the date code; “V” is an NSC internal code for die traceability. Both will vary in production. Pin Descriptions Pin Micro SMD Name A1 EN B1 Mode Description Enable pin. The device is in shutdown mode when voltage to this pin is <0.4V and enabled when >1.2V. Do not leave this pin floating. Mode Pin: Mode = 1, Forced PWM Mode = 0, ECO Do not leave this pin floating. C1 FB Feedback analog input. Connect directly to the output filter capacitor. (Figure 1) A2 VIN Power supply input. Connect to the input filter capacitor. (Figure 1) B2 SW Switching node connection to the internal PFET switch and NFET synchronous rectifier. C2 GND www.national.com Ground pin. 2 LM3691 Ordering Information Voltage Option V 0.75 0.85* 0.9* 1.0* 1.1* 1.2 1.3* 1.375* 1.5 1.6* 1.8 Order Number 6–bump Micro SMD Package Marking Supplied As LM3691TL-0.75 V 250 units, Tape-and-Reel LM3691TLX–0.75 V 3000 units, Tape-and-Reel LM3691TL-0.85 TBD 250 units, Tape-and-Reel LM3691TLX–0.85 TBD 3000 units, Tape-and-Reel LM3691TL-0.9 TBD 250 units, Tape-and-Reel LM3691TLX–0.9 TBD 3000 units, Tape-and-Reel LM3691TL-1.0 TBD 250 units, Tape-and-Reel LM3691TLX–1.0 TBD 3000 units, Tape-and-Reel LM3691TL-1.1 TBD 250 units, Tape-and-Reel LM3691TLX–1.1 TBD 3000 units, Tape-and-Reel LM3691TL–1.2 X 250 units, Tape-and-Reel LM3691TLX–1.2 X 3000 units, Tape-and-Reel LM3691TL–1.3 TBD 250 units, Tape-and-Reel LM3691TLX–1.3 TBD 3000 units, Tape-and-Reel LM3691TL–1.375 TBD 250 units, Tape-and-Reel LM3691TLX–1.375 TBD 3000 units, Tape-and-Reel LM3691TL–1.5 Y 250 units, Tape-and-Reel LM3691TLX–1.5 Y 3000 units, Tape-and-Reel LM3691TL–1.6 TBD 250 units, Tape-and-Reel LM3691TLX–1.6 TBD 3000 units, Tape-and-Reel LM3691TL–1.8 Z 250 units, Tape-and-Reel LM3691TLX–1.8 Z 3000 units, Tape-and-Reel * If any of the voltage options other than the released voltages are required, please contact the National Semiconductor Sales Office/Distributors for availability. 3 www.national.com LM3691 Absolute Maximum Ratings (Note 1) Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage Range 2.3V to 5.5V Recommended Load Current 0 mA to 1000 mA Junction Temperature (TJ) Range −40°C to +125°C Ambient Temperature (TA) Range (Note −40°C to +85°C 5) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. VIN Pin to GND EN, MODE pin to GND FB, SW pin Junction Temperature (TJ-MAX) Storage Temperature Range Continuous Power Dissipation (Note 3) Maximum Lead Temperature (Soldering, 10 sec.) ESD Rating (Note 4) Human Body Model Machine Model −0.2V to 6.0V −0.2V to 6.0V (GND−0.2V) to (VIN + 0.2V) w/ 6.0V max +150°C −65°C to +150°C Internally Limited (Notes 1, 2) Thermal Properties Junction-to-Ambient Thermal Resistance (θJA) (Note 6) (micro SMD) 85°C/W 260°C 2 kV 200V Electrical Characteristics (Notes 2, 7, 8) Limits in standard typeface are for TA = 25°C. Limits in boldface type apply over the operating ambient temperature range (−30°C ≤ TA= TJ ≤ +85°C). Unless otherwise noted, specifications apply to the LM3691 open loop Typical Application Circuit with VIN = EN = 3.6V. Symbol Parameter Condition Min PWM Mode. No load VOUT = 1.1V to 1.8V -1 PWM Mode. No load VOUT = 0.75V to 1.0V -10 Typ Max Units +1 % +10 mV 1 µA 64 80 µA 490 600 µA 160 250 mΩ 115 180 mΩ 1500 1700 mA VFB Feedback Voltage ISHDN Shutdown Supply Current EN = 0V IQ_ECO ECO Mode Iq ECO Mode IQ_PWM PWM Mode Iq PWM Mode RDSON (P) Pin-Pin Resistance for PFET VIN = VGS = 3.6V, IO = 200 mA RDSON (N) Pin-Pin Resistance for NFET VIN = VGS = 3.6V, IO = −200 mA ILIM Switch Peak Current Limit Open loop VIH Logic High Input VIL Logic Low Input IEN,MODE Input Current FSW Switching Frequency PWM Mode VON UVLO threshold VIN rising 2.2 V VIN falling 2.1 V 0.03 1250 V 1.2 3.6 0.4 V 0.01 1 µA 4 4.4 MHz Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150°C (typ.) and disengages at TJ = 130°C (typ.). Note 4: The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. MIL-STD-883 3015.7 Note 5: In applications where high power dissipation and/or poor package resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX), the maximum power dissipation of the device in the application (PD-MAX) and the junction to ambient thermal resistance of the package (θJA) in the application, as given by the following equation: TA-MAX = TJ-MAX − (θJAx PD-MAX). Due to the pulsed nature of testing the part, the temp in the Electrical Characteristic table is specified as TA = TJ. Note 6: Junction-to-ambient thermal resistance is highly application and board layout dependent. In applications where high power dissipation exists, special care must be given to thermal dissipation issues in board design. Note 7: Min and Max limits are guaranteed by design, test or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Note 8: The parameters in the electrical characteristic table are tested under open loop conditions at VIN = 3.6V unless otherwise specified. For performance over the input voltage range and closed loop condition, refer to the datasheet curves. www.national.com 4 LM3691 Block Diagram 30013431 FIGURE 3. Simplified Functional Diagram 5 www.national.com LM3691 Typical Performance Characteristics LM3691TL Typical Application Circuit (page 1), VIN = 3.6V, VOUT = 1.8V, TA = 25°, L = 1.0 μH, 2520, (LQM2HP1R0), CIN = COUT = 4.7 μF, 0603(1608), 6.3V, (C1608X5R0J475K) unless otherwise noted. Quiescent Supply current vs. Supply Voltage No Switching (ECO Mode) Quiescent Supply current vs. Supply Voltage No Switching (PWM Mode) 30013455 30013456 Shutdown Current vs. Temp (VOUT = 1.8V) Switching Frequency vs. Temp (VOUT = 1.8V, PWM Mode) 30013457 www.national.com 30013458 6 LM3691 Output Voltage vs. Supply Voltage (VOUT = 0.75V) Output Voltage vs. Supply Voltage (VOUT = 1.8V) 30013459 30013460 Output Voltage vs. Output Current (VOUT = 0.75V) Output Voltage vs. Output Current (VOUT = 1.8V) 30013461 30013462 Input Current vs. Output Current (VOUT = 0.75V) Input Current vs. Output Current (VOUT = 1.8V) 30013463 30013464 7 www.national.com LM3691 Efficiency vs. Output Current (VOUT = 0.75V, ECO Mode) Efficiency vs. Output Current (VOUT = 1.8V, ECO Mode) 30013465 30013466 Efficiency vs. Output Current (VOUT = 0.75V, FPWM Mode) Efficiency vs. Output Current (VOUT = 1.8V, FPWM Mode) 30013467 30013468 Load Current Threshold vs. Supply Voltage (VOUT = 0.75V, ECO Mode to PWM Mode) Load Current Threshold vs. Supply Voltage (VOUT = 1.8V, ECO Mode to PWM Mode) 30013469 30013470 www.national.com 8 LM3691 Output Voltage Ripple vs. Supply Voltage (VOUT = 0.75V) Output Voltage Ripple vs. Supply Voltage (VOUT = 1.8V) 30013471 30013472 Closed Loop Current Limit vs. Temperature (VOUT = 0.75V) Closed Loop Current Limit vs. Temperature (VOUT = 1.8V) 30013473 30013474 Line Transient Reponse (VOUT = 0.75V, PWM Mode) Line Transient Reponse (VOUT = 1.8V, PWM Mode) 30013475 30013478 9 www.national.com LM3691 Load Transient Reponse (VOUT = 0.75V, ECO Mode 1mA to 25 mA) Load Transient Reponse (VOUT = 0.75V, ECO Mode 25 mA to 1mA) 30013479 30013480 Load Transient Reponse (VOUT = 1.8V, ECO Mode 1mA to 25 mA) Load Transient Reponse (VOUT = 1.8V, ECO Mode 25 mA to 1mA) 30013481 30013482 Load Transient Reponse (VOUT = 0.75V, ECO Mode to PWM Mode) Load Transient Reponse (VOUT = 0.75V, PWM Mode to ECO Mode) 30013483 www.national.com 30013484 10 LM3691 Load Transient Reponse (VOUT = 1.8V, ECO Mode to PWM Mode) Load Transient Reponse (VOUT = 1.8V, PWM Mode to ECO Mode) 30013485 30013486 Load Transient Reponse (VOUT = 0.75V, FPWM Mode) Load Transient Reponse (VOUT = 0.75V, FPWM Mode) 30013487 30013488 Load Transient Reponse (VOUT = 1.8V, FPWM Mode) Load Transient Reponse (VOUT = 1.8V, FPWM Mode) 30013489 30013490 11 www.national.com LM3691 Load Transient Reponse (VOUT = 0.75V, PWM Mode) Load Transient Reponse (VOUT = 1.8V, PWM Mode) 30013491 30013492 Start Up into ECO Mode (VOUT = 1.8V, ROUT = 1.8 kΩ) Start Up into PWM Mode (VOUT = 1.8V, ROUT = 6 Ω) 30013494 30013493 Start Up into ECO Mode (VOUT = 0.75V, ROUT = 750 Ω) Start Up into PWM Mode (VOUT = 0.75V, ROUT = 2.5 Ω) 30013495 www.national.com 30013496 12 LM3691 Operation Description DEVICE INFORMATION The LM3691, a high-efficiency, step-down DC-DC switching buck converter, delivers a constant voltage from either a single Li-Ion or three cell NiMH/NiCd battery to portable devices such as cell phones and PDAs. Using a voltage mode architecture with synchronous rectification, the LM3691 has the ability to deliver up to 1000 mA depending on the input voltage and output voltage, ambient temperature, and the inductor chosen. There are three modes of operation depending on the current required - PWM (Pulse Width Modulation), ECO, and shutdown. The device operates in PWM mode at load currents of approximately 50 mA (typ.) or higher. Lighter output current loads cause the device to automatically switch into ECO mode for reduced current consumption and a longer battery life. Shutdown mode turns off the device, offering the lowest current consumption (ISHUTDOWN = 0.03 µA typ.). Additional features include soft-start, under voltage protection, current overload protection, and thermal shutdown protection. As shown in Figure 1, only three external power components are required for implementation. 30013497 FIGURE 4. Typical PWM Operation Internal Synchronous Rectification While in PWM mode, the LM3691 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. CIRCUIT OPERATION The LM3691 operates as follows. During the first portion of each switching cycle, the control block in the LM3691 turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with a slope of (VIN–VOUT)/L, by storing energy in a magnetic field. During the second portion of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the NFET to the output filter capacitor and load, which ramps the inductor current down with a slope of –VOUT/L. The output filter stores charge when the inductor current is high, and releases it when low, smoothing the voltage across the load. The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter capacitor. The output voltage is equal to the average voltage at the SW pin. Current Limiting A current limit feature allows the LM3691 to protect itself and external components during overload conditions. PWM mode implements current limit using an internal comparator that trips at 1500 mA (typ). If the output is shorted to ground and output voltage becomes lower than 0.3V (typ.), the device enters a timed current limit mode where the switching frequency will be one fourth, and NFET synchronous rectifier is disabled, thereby preventing excess current and thermal runaway. ECO OPERATION Setting mode pin low places the LM3691 in Auto mode. By doing so the part switches from ECO (ECOnomy) state to FPWM (Forced Pulse Width Modulation) state based on output load current. At light loads (less than 50 mA), the converter enters ECO mode. In this mode the part operates with low Iq. During ECO operation, the converter positions the output voltage slightly higher (+30 mV typ.) than the nominal output voltage in FPWM operation. Because the reference is set higher, the output voltage increases to reach the target voltage when the part goes from sleep state to switching state. Once this voltage is reached the converter enters sleep mode, thereby reducing switching losses and improving light load efficiency. The output voltage ripple is slightly higher in ECO mode (30 mV peak–peak ripple typ.). PWM OPERATION During PWM operation, the converter operates as a voltagemode controller with input voltage feed forward. This allows the converter to achieve excellent load and line regulation. The DC gain of the power stage is proportional to the input voltage. To eliminate this dependence, feed forward inversely proportional to the input voltage is introduced. While in PWM mode, the output voltage is regulated by switching at a constant frequency and then modulating the energy per cycle to control power to the load. At the beginning of each clock cycle the PFET switch is turned on and the inductor current ramps up until the comparator trips and the control logic turns off the switch. The current limit comparator can also turn off the switch in case the current limit of the PFET is exceeded. Then the NFET switch is turned on and the inductor current ramps down. The next cycle is initiated by the clock turning off the NFET and turning on the PFET. 13 www.national.com LM3691 switch, reference, control and bias circuitry of the LM3691 are turned off. Setting EN high (>1.2V) enables normal operation. When turning on the device with EN soft-start is activated. EN pin should be set low to turn off the LM3691 during system power up and under-voltage conditions when the supply is less than 2.3V. Do not leave the EN pin floating. SOFT-START The LM3691 has a soft-start circuit that limits in-rush current during start-up. Output voltage increase rate is 30 mV/µsec (at VOUT = 1.8V typ.) during soft-start. THERMAL SHUTDOWN PROTECTION The LM3691 has a thermal overload protection function that operates to protect itself from short-term misuse and overload conditions. When the junction temperature exceeds around 150°C, the device inhibits operation. Both the PFET and the NFET are turned off. When the temperature drops below 130° C, normal operation resumes. Prolonged operation in thermal overload conditions may damage the device and is considered bad practice. 30013498 FIGURE 5. Typical ECO Operation FORCED PWM MODE Setting Mode pin high (>1.2V) places the LM3691 in Forced PWM. The part is in forced PWM regardless of the load. SHUTDOWN MODE Setting the EN input pin low (<0.4V) places the LM3691 in shutdown mode. During shutdown the PFET switch, NFET www.national.com 14 INDUCTOR SELECTION DC bias current characteristics of inductors must be considered. Different manufacturers follow different saturation current rating specifications, so attention must be given to details. DC bias curves should be requested from them as part of the inductor selection process. Minimum value of inductance to guarantee good performance is 0.5 µH at 1.5A (ILIM typ.) bias current over the ambient temp range. The inductor’s DC resistance should be less than 0.1Ω for good efficiency at high current condition. The inductor AC loss (resistance) also affects conversion efficiency. Higher Q factor at switching frequency usually gives better efficiency at light load to middle load. Table 1 lists suggested inductors and suppliers INPUT CAPACITOR SELECTION A ceramic input capacitor of 4.7 µF, 6.3V/10V is sufficient for most applications. Place the input capacitor as close as possible to the VIN pin and GND pin of the device. A larger value or higher voltage rating may be used to improve input voltage filtering. Use X7R, X5R or B types; do not use Y5V or F. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0402. Minimum input capacitance to guarantee good performance is 2.2 µF at maximum input voltage DC bias including tolerances and over ambient temp range. The input filter capacitor supplies current to the PFET (highside) switch in the first half of each cycle and reduces voltage ripple imposed on the input power source. A ceramic capacitor's low ESR provides the best noise filtering of the input voltage spikes due to this rapidly changing current. Select an input filter capacitor with sufficient ripple current rating. The input current ripple can be calculated as: Voltage peak-to-peak ripple due to ESR = VPP-ESR = (2 * IRIPPLE) * RESR Because these two components are out of phase the rms value can be used to get an approximate value of peak-to-peak ripple. Voltage peak-to-peak ripple, root mean squared = Note that the output voltage ripple is dependent on the current ripple and the equivalent series resistance of the output capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure the value used for calculations is at the switching frequency of the part. Table 2 lists suggested capacitors and suppliers. TABLE 1. Suggested Inductors and Their Suppliers Model Vendor Dimensions LxWxH (mm) D.C.R (mΩ) LQM2HPN1R0MG0 Murata 2.5 x 2.0 x 1.0 55 MLP2520S1R0L TDK 2.5 x 2.0 x 1.0 60 KSLI252010AG1R0 HItachi Metals 2.5 x 2.0 x 1.0 80 MIPSZ2012D1R0 FDK 2.0 x 1.25 x 1.0 90 TABLE 2. Suggested Capacitors and Their Suppliers Type Vendor Voltage Rating (V) Case Size Inch (mm) C1608X5R0J475K Ceramic TDK 6.3 0603 (1608) C1608X5R1A475K Ceramic TDK 10.0 0603 (1608) Model 4.7 µF for CIN and COUT 15 www.national.com LM3691 OUTPUT CAPACITOR SELECTION Use a 4.7μF, 6.3V ceramic capacitor, X7R, X5R or B types; do not use Y5V or F. DC bias voltage characteristics of ceramic capacitors must be considered. DC bias characteristics vary from manufacturer to manufacturer, and DC bias curves should be requested from them as part of the capacitor selection process. The output filter capacitor smooths out current flow from the inductor to the load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR to perform these functions. Minimum output capacitance to guarantee good performance is 2.2 µF at the output voltage DC bias including tolerances and over ambient temp range. The output voltage ripple is caused by the charging and discharging of the output capacitor and also due to its RESR and can be calculated as: Voltage peak-to-peak ripple due to capacitance = Application Information LM3691 corners. Initially, the trace to each pad should be 7 mil wide, for a section approximately 7 mil long or longer, as a thermal relief. Then each trace should neck up or down to its optimal width. The important criteria is symmetry. This ensures the solder bumps on the LM3691 re-flow evenly and that the device solders level to the board. In particular, special attention must be paid to the pads for bumps A2 and C2, because GND and VIN are typically connected to large copper planes. The micro SMD package is optimized for the smallest possible size in applications with red or infrared opaque cases. Because the micro SMD package lacks the plastic encapsulation characteristic of larger devices, it is vulnerable to light. Backside metallization and/or epoxy coating, along with front side shading by the printed circuit board, reduce this sensitivity. However, the package has exposed die edges. In particular, micro SMD devices are sensitive to light, in the red and infrared range, shining on the package’s exposed die edges. MICRO SMD PACKAGE ASSEMBLY AND USE Use of the Micro SMD package requires specialized board layout, precision mounting and careful re-flow techniques, as detailed in National Semiconductor Application Note 1112. Refer to the section Surface Mount Technology (SMD) Assembly Considerations. For best results in assembly, alignment ordinals on the PC board should be used to facilitate placement of the device. The pad style used with micro SMD package must be the NSMD (Non-Solder Mask Defined) type. This means that the solder-mask opening is larger than the pad size. This prevents a lip that otherwise forms if the soldermask and pad overlap, from holding the device off the surface of the board and interfering with mounting. See Application Note 1112 for specific instructions how to do this. The 6-bump package used for LM3691 has 300–micron solder balls and requires 10.82 mils pads for mounting on the circuit board. The trace to each pad should enter the pad with a 90° entry angle to prevent debris from being caught in deep www.national.com 16 LM3691 Physical Dimensions inches (millimeters) unless otherwise noted 6–bump Thin Micro SMD, Large Bump NS Package Number TLA06LCA X1 = 1.260mm ± 0.030mm X2 = 1.565mm ± 0.030mm X3 = 0.600mm ± 0.075mm 17 www.national.com LM3691 High Accuracy, Miniature 1A, Step-Down DC-DC Converter for Portable Applications For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]