Source C-157-155C-FDFB-SLC9 155 mbps single mode sff lc transceiver Datasheet

155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Complies with SONET OC-3 / SDH STM-1
• 1270 nm to1610 nm Wavelength, CWDM DFB Laser
• Single +3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output (C-1XX-155C-FDFB-SLCX)
• LVPECL Signal Detection Output (C-1XX-155-FDFB-SLCX)
• Class 1 Laser International Safety Standard IEC 825
compliant
• Solderability to MIL-STD-883, Method 2003
• Flammability to UL94V0
• Humidity RH 5-85% (5-90% short term) to IEC 68-2-3
• Complies with Bellcore GR-468-CORE
• 40 km reach (C-1XX-155-FDFB-SLC5), 1270 to 1450 nm
• 80 km reach (C-1XX-155-FDFB-SLC5), 1470 to 1610 nm
• 80 km reach (C-1XX-155-FDFB-SLC9), 1270 to 1450 nm
• 120 km reach (C-1XX-155-FDFB-SLC9), 1470 to 1610 nm
• RoHS-5/6 compliance available
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Note
Power Supply Voltage
Vcc
0
3.6
V
Output Current
Iout
0
30
mA
Soldering Temperature
-
-
260
ºC
Operating Temperature
Topr
0
70
ºC
Storage Temperature
Tstg
-40
85
ºC
Symbol
Min.
Typ.
Max.
Power Supply Voltage
Vcc
3.1
3.3
3.5
V
Operating Temperature (Case)
Topr
0
-
70
ºC
-
155
-
Mbps
10 seconds on leads only
Recommended Operating Condition
Parameter
Data rate
LUMINENTOIC.COM
Unit
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Optical Transmit Power
Po
-5
Optical Transmit Power
Po
0
λ
∆λ
Side Mode Suppression Ratio
Extinction Ratio
Notes
-
0
dBm
C-1XX-155(C)-FDFB-SLC5
-
+5
dBm
C-1XX-155(C)-FDFB-SLC9
λp-5.5
-
λp
-
λp+7.5
1
nm
λp=1XX0 nm
nm
-20 dB width
Sr
30
35
-
dBm
CW, Po=5mW
ER
10
-
-
dB
Optical
Output center Wavelength
Output Spectrum Width
Output Eye
Compliant with GR-253-CORE
Optical Rise Time
tr
-
-
2
ns
10% to 90% Values
Optical Fall Time
tf
-
-
2
ns
10% to 90% Values
RIN
-
-
-116
dB/Hz
TJ
-
-
1.2
ns
Measured with 223-1 PRBS with 72 ones
and 72 zeros.
Symbol
Min
Typical
Max
Unit
Notes
Power Supply Current
ICC
-
-
180
mA
Maximum current is specified at Vcc=
Maximum @ maximum temperature
Transmit Enable Voltage
VEN
0
-
0.8
V
VD
2.0
-
Vcc
V
Data Input Current-Low
IIL
-200
-
-
µA
Data Input Current-High
IIH
-
-
200
µA
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
These inputs are compatible with 10K,
10KH and 100K ECL and PECL inputs
Symbol
Min
Typical
Max
Unit
Notes
Sensitivity
-
-
-
-35
dBm
Measured with 223-1 PRBS, BER = 10 -10
C-1XX-155(C)-FDFB-SLC5
Sensitivity
-
-
-
-36
dBm
Measured with 223-1 PRBS, BER = 10 -10
C-1XX-155(C)-FDFB-SLC9
Maximum Input Power
Pin
0
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-35
dBm
Measured on transition: low to high
C-1XX-155(C)-FDFB-SLC5
Signal Detect-Asserted
Pa
-
-
-36
dBm
Measured on transition: low to high
C-1XX-155(C)-FDFB-SLC9
Signal Detect-Deasserted
Pd
-45
-
-
dBm
Measured on transition: high to low
1.0
-
-
dB
1100
-
1620
nm
Relative Intensity Noise
Total Jitter
Transmitter Specifications
Parameter
Electrical
Transmit Disable Voltage
Receiver Specifications
Parameter
Optical
Signal Detect-Hysteresis
Wavelength of Operation
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Note
Electrical
ICC
-
-
120
mA
The current excludes the output load current
Data Output Voltage-Low
VOL -Vcc
-2
-
-1.58
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
These outputs are compatible with 10K,
10KH and 100K ECL and LVPECL outputs
Signal Detect Output Voltage-Low
VSDL-Vcc
-2
-
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-
-0.74
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-
-
0.5
V
Signal Detect Output Voltage-High
VSDH- Vcc
2.0
-
-
V
Power Supply Current
C-1XX-155-FDFB-SLCX
C-1XX-155C-FDFB-SLCX
Connection Diagram
Legal Notice
PIN
Symbol
1
RxGND
2
TxVcc
Notes
Directly connect this pin to the receiver ground plane
+3.3 V dc power for the receiver section
3
SD
Active high on this indicates a received optical signal(LVPECL/LVTTL)
4
RD-
Receiver Data Out Bar (LVPECL)
5
RD+
Receiver Dat Out (LVPECL)
6
TxVcc
7
TxGND
8
TxDIS
9
TD+
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
Attaching Posts
LUMINENTOIC.COM
+3.3 V dc power for the transmitter section
Directly connect this pin to the transmitter ground plane
Transmitter disable (LVTTL)
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Recommended Circuit Schematic
C-1XX-155-FDFB-SLCX
PHY DEVICE
Vcc(+3.3V)
TERMINATE AT
TRANSCEIVER INPUTS
Z=50�
TD-
LVPECL
100�
Z=50�
TD+
130�
1
Tx Disable
TxGND
TxVcc
RD-
RD+
6
TxDIS
TD+
2
7
SD
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
3
4
130�
1�H
Vcc(+3.3V)
C2
C3
10�F
Vcc(+3.3V)
1�H
C1
5
LVTTL
RD+
Z=50�
LVPECL
100�
RD-
Vcc(+3.3V)
Z=50�
130�
130�
130�
Z=50�
SD
LVPECL
82�
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
PHY DEVICE
C-1XX-155C-FDFB-SLCX
TERMINATE AT
TRANSCEIVER INPUTS
Vcc(+3.3V)
Z=50�
TD-
LVPECL
100�
Z=50�
TD+
130�
1
2
3
Tx Disable
TxDIS
TxGND
TxVcc
RD+
6
SD
7
RD-
TD+
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
4
130�
1�H
Vcc(+3.3V)
C2
C3
10�F
Vcc(+3.3V)
1�H
C1
5
LVTTL
RD+
Z=50�
LVPECL
100�
RD-
Vcc(+3.3V)
Z=50�
130�
130�
Z=50�
SD
LVTTL
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Package Diagram
C-1XX-155(C)-FDFB-SLCX
Units: mm (inches)
48.8+
-.
17
(0.039±0.002)
(0.070)
177
712
(0.280)
1016
(0.400)
.8
31�05
050
(0.020)
100�005
000)
(0.386)+(
-(0.004)
(0.150±0.02)
1050
(0.413)
+
-.�
950
(0.374)
1320
(0.520)
�. +
-.�
000)
(0.535)+(
-(0.004)
000)
(1.921)+(
-(0.008)
50
(0.200)
625
(0.246)
(0.700)
48.8+
-.
000)
(1.921) +(
-(0.008)
C-1XX-155(C)-FDFB-SLCXS
Units: mm (inches)
+
-
10.16
(0.400)
.000)
(0.535) +(
-(0.004)
� +
-�
13.20
(0.520)
(0.594)
�
.000)
(1.921)+(
-(0.008)

�
1.78
(0.039±0.002)
(0.070)
17.78
7.12
(0.280)
5.08
(0.200)
(0.386)


.000)
(0.386) +(
-(0.004)
3.81�0.5
0.50
(0.020)
1.00�0.05
(0.150±0.02)
10.50
(0.413)
+
-�
(0.374)
9.50
(0.447)
��
(0.531)
�

(0.155)
(0.086)
(0.274)
6.25
(0.246)
(0.700)
Case with metal Shielding Finger
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Printed Circuit Board Layout Consideration
A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies
signals that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must
be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of
signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high
speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter
be used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS850-Apr0706
Rev A.2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Ordering Information
Available Options:
C-1XX-155-FDFB-SLC5(S)
C-1XX-155-FDFB-SLC9(S)
C-1XX-155C-FDFB-SLC5(S)
C-1XX-155C-FDFB-SLC9(S)
Part numbering Definition:
C-1XX-155-FDFB-SLC5(S)-G5
C-1XX-155-FDFB-SLC9(S)-G5
C-1XX-155C-FDFB-SLC5(S)-G5
C-1XX-155C-FDFB-SLC9(S)-G5
C - 1XX - 155(C) - FDFB
- S
LC TxPower
Package - RoHS
• 1XX = Wavelength 1XX0 nm
XX=27, 29, 31, 33, 35, 37, 39, 41, 43,
45, 47, 49, 51, 53, 55, 57, 59, 61
• Communication protocol
155= LVPECL SD output
155C= LVTTL SD output
• FDFB = +3.3V SFF Transceiver
• Single mode fiber
• Connector options
• Tx Power range
5 = -5 to 0 dBm
9 = 0 to +5 dBm
• Package
Blank = Standard Package
S = EMI Shielding Finger Package
• Blank = No RoHS compliant
G5 = RoHS-5/6 compliant (lead exemption)
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS850-Apr0706
Rev A.2
Similar pages