Intersil HC5503TCB Balanced pbx/key system slic, subscriber line interface circuit Datasheet

HC5503T
Data Sheet
June 1998
File Number 4506
Balanced PBX/Key System SLIC,
Subscriber Line Interface Circuit
Features
The Intersil HC5503T is a low cost Subscriber Line Interface
Circuit (SLIC) that replaces the components of a discrete
Transformer Analog circuit design. The monolithic integrated
design provides improved performance and system reliability.
• Controlled Supply of Battery Feed Current for Short Loops
(30mA)
• Monolithic Integrated Device
• Single +5V Supply
• Allows Interfacing With All Ringing Systems
The HC5503T provides: Current limited DC feed to the
subscriber loop, maintains a flat frequency response over the
voice band and beyond, has self resetting thermal protection
that allows conversation to continue while the fault is
present, provides a TTL subscriber off hook indication even
in the presence of longitudinal currents, and limits system
power consumption on short loops.
• Switch Hook Detection
• Compatible With Worldwide PBX Performance
Requirements
• Low Power Consumption During Standby
Applications
The HC5503T provides balanced 2-wire transmission and
has excellent longitudinal balance, while providing on hook
transmission and longitudinal current rejection in both the
on-hook or off-hook conditions.
• PBX Switches (Analog, Digital or ISDN)
• Key Telephone Systems (KTS)
• ISDN PC Plug in Modems
• ISDN Small Office / Home Office (SOHO) Terminal
Adapters (TA)
The SLIC needs only one +5V supply in addition to the main
battery supply for loop current and operates over a range of
battery voltages (-24V to -58V).
• CTI (Computer Telephony Integration) Products
Available in 22PDIP AND 24SO packaging. The HC5503T is
ideally suited as a replacement for discrete line circuits in
low cost analog PABXs, small Office/Home Office products
or Small Key Systems.
Ordering Information
PART NUMBER
TEMP.
RANGE (oC)
PACKAGE
PKG. NO.
HC5503TCP
0 to 75
22 Ld PDIP
E22.4
HC5503TCB
0 to 75
24 Ld SOIC
M24.3
Block Diagram
BGND
TIP
RING
C1
TF
RF
TX
SPEECH CIRCUIT
LOOP FEED
RX
VBAT
LOOP DETECTOR
SHD
BIAS
RS
50
VCC
AGND
DGND
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
HC5503T
Absolute Maximum Ratings (Note 1)
Thermal Information
Maximum Continuous Supply Voltages
(VBAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -60 to 0.5V
(VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7V
(VCC - VBAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75V
Relay Drive Voltage (VRD) . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 15V
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Maximum Junction Temperature (Plastic Package) . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range
HC-5503T-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Positive Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . 4.75V to 5.25V
Negative Supply Voltage (VBAT) . . . . . . . . . . . . . . . . . .-24V to -58V
High Level Logic Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V
Low Level Logic Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6V
Die Characteristics
Transistor Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Diode Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Die Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 x 102
Substrate Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connected
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Absolute maximum ratings are limiting values, applied individually, beyond which the serviceability of the circuit may be impaired. Functional
operability under any of these conditions is not necessarily implied.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
Unless Otherwise Specified, VBAT = -48V, VCC = 5V, AG = BG = DG = 0V, Typical Parameters
TA = 25oC. Min-Max Parameters are Over Operating Temperature Range
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Off Hook IB+
RL = 600Ω, TA = 25oC
-
-
5.3
mA
Off Hook IB-
RL = 600Ω
-
-
39
mA
Off Hook Loop Current
RL = 1200Ω
-
21
-
mA
Off Hook Loop Current
RL = 1200Ω, VBAT = -42V, TA = 25oC
17.5
-
-
mA
Off Hook Loop Current
RL = 200Ω
25.5
30
34.5
mA
Switch Hook Detection Threshold
SHD = VOL
10
-
-
mA
SHD = VOH
-
-
5
mA
0
-
5
µs
-
65
-
dB
2-Wire On Hook
-
63
-
dB
Tip and Ring to TX, Off Hook
-
58
-
dB
-
±0.05
±0.2
dB
-
±0.02
±0.05
dB
-
1
5
dBrnC
-
-89
-85
dBm0p
-
40
-
dB
2.5
-
-
VPeak
Dial Pulse Distortion
Longitudinal Balance
1VRMS 200Hz - 3400Hz, (Note 3) IEEE Method
0oC ≤ TA ≤ 75oC
2-Wire Off Hook
Insertion Loss
At 1kHz, 0dBm Input Level, Referenced 600Ω
2-Wire to TX, RX to 2-Wire
Frequency Response
200 - 3400Hz Referenced to Absolute Loss at 1kHz and
0dBm Signal Level (Note 3)
Idle Channel Noise
(Note 3)
2-Wire to TX, RX to 2-Wire
Trans Hybrid Loss
RX to TX
Balance Network Set Up for 600Ω Termination at 1kHz
Overload Level, 2-Wire to TX, RX to 2-Wire
VCC = +5V, (Note 3)
51
HC5503T
Electrical Specifications
Unless Otherwise Specified, VBAT = -48V, VCC = 5V, AG = BG = DG = 0V, Typical Parameters
TA = 25oC. Min-Max Parameters are Over Operating Temperature Range (Continued)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
+3 to -40dBm
-
-
±0.05
dB
-40 to -50dBm
-
-
±0.1
dB
-50 to -55dBm
-
-
±0.3
dB
-
40
-
dB
VCC to Transmit
-
40
-
dB
VBAT to 2-Wire
-
40
-
dB
VBAT to Transmit
-
40
-
dB
-
-
±100
µA
Logic ‘0’ VIL
-
-
0.8
V
Logic ‘1’ VIH
2.0
-
5.5
V
Level Linearity
2-Wire to TX, RX to 2-Wire
At 1kHz, (Note 3) Referenced to 0dBm Level
Power Supply Rejection Ratio
(Note 3)
VCC to 2-Wire
200 - 3400kHz, RL = 600Ω
0V ≤ VIN ≤ 5V
Logic Input Current (RS, RC)
Logic Inputs (RS, RC)
Logic Output (SHD)
Logic ‘0’ VOL
ILOAD 800µA, VCC = 5V
-
0.1
0.5
V
Logic ‘1’ VOH
ILOAD 40µA, VCC = 5V
2.7
-
5.0
V
NOTES:
3. These parameters are controlled by design or process parameters and are not directly tested. These parameters are characterized upon initial
design release, upon design changes which would affect these characteristics, and at intervals to assure product quality and specification compliance.
Pinouts
HC5503T
(PDIP)
TOP VIEW
HC5503T
(SOIC)
TOP VIEW
TIP
1
22 TX
TIP
1
24 TX
RING
2
21 AGND
RING
2
23 AGND
VCC
3
20 N/C
VCC
3
22 N/C
C1
4
19 RX
N/C
4
21 RX
DGND
5
18 T3
C1
5
20 T3
RS
6
17 T2
DGND
6
19 T2
N/C
7
16 T1
RS
7
18 T1
TF
8
15 N/C
N/C
8
17 N/C
RF
9
14 N/C
TF
9
16 N/C
VBAT 10
13 N/C
RF 10
15 N/C
BGND 11
12 SHD
VBAT 11
14 N/C
BGND 12
13 SHD
52
HC5503T
Pin Descriptions
22 PIN
PDIP
24 PIN
SOIC
SYMBOL
DESCRIPTION
1
1
TIP
An analog input connected to the TIP (more positive) side of the subscriber loop through a 150Ω feed resistor.
Functions with the Ring terminal to receive voice signals from the telephone and for loop
monitoring purposes.
2
2
RING
An analog input connected to the RING (more negative) side of the subscriber loop through a 150Ω feed resistor. Functions with the Tip terminal to receive voice signals from the telephone and for loop monitoring
purposes.
3
3
VCC
Positive Voltage Source - Most positive supply. VCC is typically 5V.
4
N/C
No Connect. For proper operation this pin should be left floating.
4
5
C1
Capacitor - An external capacitor to be connected between this terminal and analog ground. Required for
proper operation of the voice band hybrid. Typical value is 0.3µF, 30V.
5
6
DGND
Digital Ground - To be connected to zero potential and serves as a reference for all digital inputs and outputs
on the SLIC microcircuit.
6
7
RS
This pin should be tied to 5V.
7
8
N/C
No Connect. For proper operation this pin should be left floating.
8
9
TF
Tip Feed - A low impedance analog output connected to the TIP terminal through a 150Ω feed resistor. Provides voice signals to the telephone set and sink longitudinal current.
9
10
RF
Ring Feed - A low impedance analog output connected to the RING terminal through a 150Ω feed resistor.
Functions with the TF terminal to provide loop current, feed voice signals to the telephone set, and sink longitudinal current.
10
11
VBAT
Negative Voltage Source - Most negative supply. VBAT has an operational range of -24V to -58V.
Frequently referred to as “battery”.
11
12
BGND
Battery Ground - To be connected to zero potential. All loop current and some quiescent current flows into
this ground terminal.
12
13
SHD
Switch Hook Detection - A low active LS TTL - compatible logic output. This output is enabled for loop currents exceeding 10mA and disabled for loop currents less than 5mA.
13
14
N/C
No Connect. For proper operation this pin should be left floating.
15
N/C
No Connect. For proper operation this pin should be left floating.
14
16
N/C
No Connect. For proper operation this pin should be left floating.
15
17
N/C
No Connect. For proper operation this pin should be left floating.
16
18
T1
Used during production testing. For proper operation this pin should be connected to pin T2.
17
19
T2
Used during production testing. For proper operation this pin should be connected to pin T1.
18
20
T3
Used during production testing. For proper operation this pin should be connected to Analog Ground pin
AGND.
19
21
RX
Receive Input - A high impedance analog input which is internally biased. Capacitive coupling to this input is
required. AC signals appearing at this input differentially drive the Tip feed and Ring feed terminals, which in
turn drive tip and ring through 300Ω of feed resistance on each side of the line.
20
22
N/C
No Connect. For proper operation this pin should be left floating.
21
23
AGND
Analog Ground - To be connected to zero potential and serves as a reference for the transmit output (TX)
and receive input (RX) terminals.
22
24
TX
Transmit Output - A low impedance analog output which represents the differential voltage across Tip and
Ring. This output is unbalanced and referenced to analog ground. Since the DC level of this output varies
with loop current, capacitive coupling to the next stage is essential.
NOTE: All grounds (AGND, BGND, and DGND) must be applied before VCC or VBAT. Failure to do so may result in premature failure of the part. If
a user wishes to run separate grounds off a line card, the AG must be applied first.
53
HC5503T
Applications Diagram
SYSTEM CONTROLLER
13
5V
7
C5
SHD
RS
TX
RB1
K1A
TIP
1
RB2
9
TIP
RX
TIP FEED
SLIC
HC5503T
(NOTE 4)
VBAT
10
T2
RING FEED
RB4
2
K1A
RB3
RING
T1
RING
VBAT
11
BGND DGND AGND
C2
12
6
23
C1
VCC
C3
C4
21
20
T3
PRIMARY
SUBSCRIBER PROTECTION
LOOP
24
3
19
18
5
C1
PTC
VCC
-48V
PIN NUMBERS GIVEN FOR SOIC PACKAGE.
Z1
RING GENERATOR
-48V
FIGURE 1. TYPICAL LINE CIRCUIT APPLICATION WITH THE MONOLITHIC SLIC
Typical Component Values
C1 = 0.3µF, 30V, ±20%
C4 = 0.5µF, 20V, ±20%
C2 = 0.01µF, 100V,±20%
C5 = 0.5µF, 30V, ±20%
C3 = 0.01µF, 20V, ±20%
RB1 = RB2 = RB3 = RB4 = 150Ω
PTC used as ring generator ballast.
NOTES:
4. Secondary protection diode bridge recommended is a 2A, 200V type.
5. All grounds (AG, BG, and DG) must be applied before VCC or VBAT. Failure to do so may result in premature failure of the part. If a user wishes
to run separate grounds off a line card, the AG must be applied first.
6. Application shows Ring Injected Ringing.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
54
Similar pages