MUR3020CT THRU MUR3060CT R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 30.0Amperes S E M I C O N D U C T O R FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency Low forward voltage drop Single rectifier construction High surge capability For use in low voltage ,high frequency inverters, JF MUR3020 free wheeling ,and polarity protection applications High temperature soldering guaranteed:260°C/10 seconds, 0.25"(6.35mm)from case Component in accordance to RoHS 2011/65/EU 0.159(4.05) TO-220AB 0.185(4.70) 0.410(10.41) 0.161(4.10) 0.390(9.91) 0.147(3.74) DIA 0.175(4.44) 0.055(1.39) 0.045(1.14) 0.114(2.90) 0.102(2.60) 0.283(7.20) 0.244(6.20) 1 PIN 2 3 1.161(29.50) 0.114(2.90) 1.106(28.10) 0.138(3.50) 0.560(14.22) 0.053(1.34) 0.516(13.10) 0.047(1.20) 0.037(0.94) MECHANICAL DATA 0.027(0.68) 0.105(2.67) 0.023(0.58) 0.095(2.41) Case: JEDEC TO-220AB molded plastic body 0.014(0.35) 0.208(5.28) Terminals: Lead solderable per MIL-STD-750,method 2026 0.192(4.88) Polarity: As marked Mounting Position: Any Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25 C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current(see Fig.1) Per leg Total device Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 15.0 A per leg(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) T A =25°C TA =125°C Maximum Reverse Recovery Time (Note 2) Typical thermal resistance (Note 3) Operating junction temperature range Storage temperature range Symbols MUR 3020CT MUR 3040CT MUR 3060CT VRRM VRMS VDC 200 400 600 140 280 420 200 400 600 Units Volts Volts Volts I(AV) 15.0 30.0 Amps IFSM 150.0 220 Amps VF 0.98 1.3 5 IR 250 1.7 Volts μA 35 ns RθJC 2.5 °C/W TJ TSTG -55 to+150 °C -55 to+150 °C Trr Notes: 1. Pulse test: 300 s pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.25A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 0.098(2.50) 2-1 WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MUR3020CT THRU MUR3060CT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 36 280 PEAK FORWARD SURGE CURRENT (AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 30 RESISTIVE OR INDUCTVE LOAD 24 18 12 6 0 0 20 40 60 80 100 120 180 150 8.3ms Single Half Sine-Wave (JEDEC Method) 240 200 160 120 80 40 0 LEAD TEMPERATURE (°C) 1 2 5 20 50 100 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 10 400V 10 TJ=100°C (uA) 200V 600V INSTANTANEOUS REVERSE CURRENT INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PULSE WIDTH=300μS 1% DUTY CYCLE 1 0.1 1 TJ=25°C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/ W FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 4000 TJ=25°C f=1.0MHZ Vsig=50mVp-p 1000 100 0.1 1 10 100 REVERSE VOLTAGE. VOLTS JINAN JINGHENG ELECTRONICS CO., LTD. 100 10 1 0.1 0.01 0.1 1 10 T, PULSE DURATION ,sec. 2-2 WWW.JINGHENGGROUP.COM 100