IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Distinctive features and specifications UG1212-A-R1 ❑ Illuminated or non-illuminated ❑ Tactile feedback ❑ Wide variety of configurations ❑ Flat round actuator for optional marking ❑ Sealed to IP67 B1 ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS • Front panel sealing : IP67 according to IEC 60529 IP69K according to DIN 40050-9 (non-illuminated) with cap U5125 • Shock resistance : 100 g according to IEC 512-4, test 6c • Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d • Salt spray : IEC 512-6, test 11f • Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule) • Operating temperature : -40°C to +85°C ELECTRICAL SPECIFICATIONS • Max. current/voltage rating with resistive load (gold plated silver contacts): 5A 28VDC, 70.000 cycles For W terminals, current has to 0,2A 48VDC, 500.000 cycles be limited to 400mA. 0,5A 48VAC, 500.000 cycles • Initial contact resistance : 100 mΩ max. • Insulation resistance : 1 GΩ min. at 500VDC • Dielectric strength : 1.500 Vrms • Contact bounce : 10 ms LED COMPONENT SPECIFICATIONS LED colour Forward current Super red (L0S) 20mA Typ. forward voltage Max. forward voltage 2,1V 2,3V Yellow (L0Y) 20mA 2,1V 2,3V Green (L0G) 20mA 2,1V 2,3V Blue (L0B) 20mA 3,2V 3,8V White (L0W) 20mA 3,35V 4,25V • Panel thickness : 1,5 mm (.059) min. 4 mm (.157 max.) • Total travel : Funct. 3 : 1,7 mm (.067) +/- 0,3 mm Funct. 5 : 1,3 mm (.051) +/- 0,3 mm • Typical operating force : 6N +/- 2N • Low level/mech. life : 1.000.000 cycles • Torque : 1,5 Nm max. applied to nut • Soldering : 320°C max. for 3 sec. MATERIALS • Case : thermoplastic UL94-V0 • Actuator : polyamide 6/6 • Bushing/bezel : zinc die-cast (zamac), black painted • Contacts : silver, gold plated (std) brass, gold plated (for option 104) • Output wires (flying lead terminals) : F version : AWG20, section 0,6 mm2 W version : AWG24, section 0,23 mm2 • LED wires : F version : AWG26, section 0,12 mm2 W version : AWG24, section 0,23 mm2 • Lens : polycarbonate • Terminal seal : epoxy AGENCY APPROVAL A resistor must be series-connected by the user. Resistor value = supply voltage - LED forward voltage LED forward current 2A 125VAC/250VAC File E83438 See following pages. MOUNTING ➀ O-ring APEM 20.00 (.787) Ø13.50 (.531DIA) www.apem.com 17.50 (.688) Ø13.60 (.535DIA) 1 20.00 (.787) Back of panel space requirement 20.00 (.787) 12.90 (.507) Matrix mounting 1.50min-4Max (.059 min-.157max) Panel cut-out CIPCE1 B1-15 IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Overview IP SERIES Electrical functions Actuator shapes C R P Square Round, curved Round, flat 3 5 Normally open (NO) NC/NO combined (non-illuminated) Terminals S F W P Z1 B1 Actuator colours 1 B 2 3 4 5 6 7/1 8 9 A Blue Dark blue Black Green Grey Yellow Red White Bright chrome Orange Satin chrome LED colours Blank L0S L0Y L0G L0B L0W Non-illum. Super red Yellow Green Blue White Solder lugs Flying leads, standard Flying leads, thin NEW! Straight PC Quick-connect (non-ill., NO only ) 101 104 Satin chrome bezel Bright chrome bezel High actuator (non-illum. round models only) AD Silver, gold plated (standard) CD Brass, gold plated (option 104) Approval Options 100 Contacts UL Consult factory for detail of approved models. Option 104 If combined with electrical function 5 (NC/NO), this option should be ordered with CD contacts (brass, gold plated). Current/voltage rating : 100mA 30VDC ABOUT THIS SERIES On the following pages, you will find successively : model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand. It is presented after the IA series and in section H. Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring. Hex nut part number U166. Packaging unit : 25 pieces B1-16 www.apem.com APEM IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Square - illuminated • High brightness illumination • Five LED colours • Tin plated LED terminals LED Cathode (-) MODEL STRUCTURE B1 Shown with standard flying lead terminals. Also available with straight PC terminals : IPC3PAD LED colour is indicated by the bottom of the switch. 1.50 Min (.059 Min) EPOXY 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) 1.20 (.047) 2.00 (.078) 17.50 (.688SQ) 6.80 (.267) 5.00 (.196) Ø12.00x0.75SI (.472DIAx0.75IS) 500±10 (19.68±.393) For THIN flying leads, replace F with W. 16.00 Max (.629 Max) Normally Open 12.00 (.472SQ) 1.50 Min (.059 Min) ➞ Flat Sealed flying lead terminals IPC3FAD 17.50 (.688SQ) Ø12.00x0.75SI (.472DIAx0.75IS) 6.10 (.240) Normally Open 1.50 (.059) IPC3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) 12.00 (.472SQ) 2.00 (.078) ➞ Flat Solder lug terminals Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-) ACTUATOR COLOURS LED COLOURS 1 : blue - B : dark blue - 2 : black - 3 : green - 4 : grey 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - A : satin chrome L0S : super red - L0Y : yellow - L0G : green - L0B : blue L0W : white OPTIONS APPROVAL 100 : Satin chrome bezel 101 : Bright chrome bezel UL Consult factory for details of approved models. To order switches marked UL, complete above box with ”UL”. APEM www.apem.com B1-17 IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Square - non-illuminated • Double function (NC/NO combined) with a short behind-panel depth 8.70 8.70 (.342) (.342) 1.00 1.00 (.039) (.039) Function 3 (N0) CIPCOSP CIPCOSP CIPCOSZ1 CIPCOSZ1 Shown with standard flying lead terminals. IPC5SAD NC/NO combined Also available with straight PC terminals : IPC3PAD (NO) or IPC5PAD (NC/NO) and quick-connect terminals : IPC3Z1AD (NO only) 2.00 (.078) Ø12.00x0.75SI (.472DIAx0.75IS) EPOXY 1.20 (.047) 2.00 (.078) NO NC 0.40 (.015) 5.08 (.200) NO 17.50 (.688SQ) NO 5.20 (.204) Normally Open 1.50 (.059) IPC3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) 12.00 (.472SQ) 1.50 Min (.059 Min) ➞ Solder lug terminals Flat NC/NO NC/NO combined 17.50 (.688SQ) Ø12.00x0.75SI (.472DIAx0.75IS) 500±10 (19.68±.393) IPC5FAD 2.00 (.078) 5.00 (.196) Normally Open 6.80 (.267) IPC3FAD 12.00 (.472SQ) 1.50 Min (.059 Min) ➞ Flat Sealed flying lead terminals 16.00 Max (.629 Max) B1 1.20 1.20 (.047) (.047) 2.80 2.80 (.110) (.110) Function 5 (NC/NO) MODEL STRUCTURE 2.40 2.40 (.094) (.094) Quick-connect Z1 4.55 4.55 (.179) (.179) 5.20 5.20 (.204) (.204) Straight P For THIN flying leads, replace F with W. NO NC/NO Wire colours (NC/NO) : black : NO, blue : NC ACTUATOR COLOURS 1 : blue - B : dark blue -2 : black - 3 : green - 4 : grey - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - A : satin chrome OPTIONS APPROVAL 100 : Satin chrome bezel 101 : Bright chrome bezel UL Consult factory for details of approved models. To order switches marked UL, complete above box with ”UL”. B1-18 www.apem.com APEM IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Round - illuminated • High brightness illumination • Five LED colours • Tin plated LED terminals LED Cathode (-) LED Cathode (-) MODEL STRUCTURE B1 Shown with standard flying lead terminals. Also available with straight PC terminals : IPR3PAD LED colour is indicated by the bottom of the switch. 1.50 Min (.059 Min) EPOXY 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) 1.20 (.047) 2.00 (.078) Ø17.50 (.688DIA) 6.80 (.267) 5.00 (.196) Ø12.00x0.75SI (.472DIAx0.75IS) 500±10 (19.68±.393) For THIN flying leads, replace F with W. 16.00 Max (.629 Max) Normally Open Ø12.00 (.472DIA) 1.50 Min (.059 Min) ➞ Flat Sealed flying lead terminals IPR3FAD Ø17.50 (.688DIA) Ø12.00x0.75SI (.472DIAx0.75IS) 6.10 (.240) Normally Open 1.50 (.059) IPR3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) Ø12.00 (.472DIA) 2.00 (.078) ➞ Flat Solder lug terminals Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-) ACTUATOR COLOURS LED COLOURS 1 : blue - B : dark blue - 2 : black - 3 : green - 4 : grey 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - A : satin chrome L0S : super red - L0Y : yellow - L0G : green - L0B : blue L0W : white OPTIONS APPROVAL 100 : Satin chrome bezel 101 : Bright chrome bezel UL Consult factory for details of approved models. To order switches marked UL, complete above box with ”UL”. APEM www.apem.com B1-19 IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Round - non-illuminated • Double function (NC/NO combined) with a short behind-panel depth Function 5 (NC/NO) MODEL STRUCTURE 2.40 2.40 (.094) (.094) 8.70 8.70 (.342) (.342) 2.80 2.80 (.110) (.110) 1.20 1.20 (.047) (.047) CIPCOSP CIPCOSZ1 CIPCOSP Shown with standard flyingCIPCOSZ1 lead terminals. Actuator marking available on IPP models (symbol 10 mm max.). On request. 5.00 (.196) Ø17.50 (.688DIA) Ø12.00x0.75SI (.472DIAx0.75IS) NO 1.50 (.059) 1.20 (.047) 2.00 (.078) NO NC EPOXY 0.40 (.015) 5.20 (.204) Flat actuator, NO IPP3SAD Flat actuator, NC/NO IPP5SAD 6.40 6.80 (.251) (.267) Curved actuator, NO IPR3SAD Curved actuator, NC/NO IPR5SAD Ø12.00 (.472DIA) 2.00 (.078) ➞ Flat Solder lug terminals 5.08 (.200) NO NC/NO Also available with straight PC terminals : IP•3PAD (NO) or IP•5PAD (NC/NO) and quick-connect terminals : IP•3Z1AD (NO only) 1.50 Min (.059 Min) 5.00 (.196) Ø17.50 (.688DIA) 6.80 (.267) Curved actuator, NO IPR3FAD Curved actuator, NC/NO IPR5FAD Ø12.00 (.472DIA) 2.00 (.078) ➞ Flat Sealed flying lead terminals Ø12.00x0.75SI (.472DIAx0.75IS) Flat actuator, NO IPP3FAD Flat actuator, NC/NO IPP5FAD For THIN flying leads, replace F with W. NO 500±10 (19.68±.393) 13.20 (.519) NC/NO Wire colours (NC/NO) : black : NO, blue : NC OPTIONS 1 : blue - B : dark blue - 2 : black - 3 : green - 4 : grey 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - A : satin chrome 100 : Satin chrome bezel 101 : Bright chrome bezel 104 : High actuator - If combined with function 5 (NC/NO), order with CD contacts (instead of AD contacts). Ø12.00 (.472DIA) APPROVAL UL Consult factory for details of approved models. To order switches marked UL, complete above box with ”UL”. B1-20 www.apem.com 104 IPR Ø12.00 (.472DIA) 104 4.70 (.185) ACTUATOR COLOURS 4.70 (.185) B1 1.00 1.00 (.039) (.039) 1.50 Min (.059 Min) Function 3 (NO) Quick-connect Z1 4.55 4.55 (.179) (.179) 5.20 5.20 (.204) (.204) Straight P IPP APEM Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apem: IPC1FAD2 IPC1FAD2L0G IPC1FAD2L0Y IPC1FAD6 IPC1SAD1L0G IPC1SAD1L0Y IPC1SAD2 IPC1SAD3L0G IPC1SAD6 IPC1SAD6L0S IPR1FAD2 IPR1FAD2L0G IPR1FAD2L0Y IPR1FAD3L0G IPR1FAD6 IPR1FAD6L0S IPR1SAD1L0Y IPR1SAD2L0G IPR1SAD2L0S IPR1SAD2L0Y IPR1SAD3 IPR1SAD3L0G IPR1SAD5 IPR1SAD5104 IPR1SAD5L0S IPR1SAD6 IPR1SAD6104 IPR1SAD6L0S IPR1SAD2 IPC1SAD2L0S IPR1FAD2L0S IPR1SAD7/1L0S IPC1FAD2L0B IPC1Z1AD2L0B IPR1Z1AD1L0Y IPR1SAD5-LOS IPR1SAD2L0B IPR1SAD9LOS