AZ963 SPDT SUBMINIATURE POWER RELAY FEATURES • • • • • • • 4 kV dielectric strength, 5 kV surge Proof tracking index (PTI/CTI) 250 6 Amp switching 10 A version (1 Form A) upon request Epoxy sealed UL, CUR file E43203 VDE file 40011689 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A and 1 Form B) Ratings Resistive load: Max. switched power: 180 W or 1500 VA Max. switched current: 6A Max. switched voltage: 220 VDC* or 380 VAC Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 6 A 250 VAC Res. Operate Time (typical) 6 ms at nominal coil voltage Release Time (typical) 4 ms at nominal coil voltage (with no coil suppression) * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR VDE 6 A at 250 VAC, Resistive 6 A at 24 VDC, Resistive 5 A at 250 VAC, Resistive [1] 4 A at 250 VAC, Resistive [2] Material Silver nickel [1] or silver tin oxide [2] Resistance <100 milliohms initially COIL Power Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Surge Voltage Coil to contact 5,000V (at 1.2x50 µs) Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 2 Nominal voltage: 250 VAC Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" (1.5 mm) DA at 10–50 Hz Shock 20 g operating, 100 g damage Enclosure P.B.T. polyester At Pickup Voltage (typical) 113 mW Max. Continuous Dissipation 0.96 W at 20°C (68°F) ambient Temperature Rise 30°C (54°F) at nominal coil voltage Terminals Tinned copper alloy, P. C. Max. 155°C (266°F) Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 5 grams Packing unit in pcs 20 per plastic tube / 1000 per carton box Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2004-11-29 AZ963 RELAY ORDERING DATA STANDARD RELAYS COIL SPECIFICATIONS ORDER NUMBER* Nominal Coil VDC 3 Must Operate VDC 2.25 Max. Continuous VDC 6.6 Coil Resistance Ohm ± 10% 45 AZ963–1A–3DE AZ963–1C–3DE 5 3.75 11.0 125 AZ963–1A–5DE AZ963–1C–5DE 6 4.5 13.2 180 AZ963–1A–6DE AZ963–1C–6DE Form A (SPST) Form C (SPDT) 9 6.75 19.6 405 AZ963–1A–9DE AZ963–1C–9DE 12 9.0 26.4 720 AZ963–1A–12DE AZ963–1C–12DE 18 13.5 36.6 1,620 AZ963–1A–18DE AZ963–1C–18DE 24 18.0 52.8 2,880 AZ963–1A–24DE AZ963–1C–24DE 36 27.0 79.2 6,480 AZ963–1A–36DE AZ963–1C–36DE 48 36.0 105.6 11,520 AZ963–1A–48DE AZ963–1C–48DE * Substitute “1B” in place of “1A” for 1 Form B contact. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. MECHANICAL DATA PC BOARD LAYOUT Not used on 1 Form B relay Viewed toward terminals Not used on 1 Form A relay WIRING DIAGRAM Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2004-11-29