ICST MK3771-17RTR Vcxo and hdtv set-top clock source Datasheet

MK3771-17
VCXO and HDTV Set-Top Clock Source
Description
Features
The MK3771-17 is a low cost, low jitter,
high-perfomance VCXO and clock synthesizer
designed for set-top boxes and HDTV receivers. The
on-chip Voltage Controlled Crystal Oscillator accepts a
0 to 3.3 V input voltage to cause the output clocks to
vary by ±100 ppm. Using ICS’s patented VCXO and
analog Phase-Locked Loop (PLL) techniques, the
device uses an inexpensive 13.5 MHz crystal input to
produce multiple output clocks including selectable
BCLK, a selectable audio clock, two communications
clocks, a 13.5 MHz clock, and three 27 MHz clocks. All
clocks are frequency locked to the 27 MHz output (and
to each other) with zero ppm error, so any output can
be used as the VCXO output.
•
•
•
•
Packaged in 28-pin SSOP
•
•
•
•
VCXO tuning voltage of 0 to 3.3 V
Available in Pb (lead) free package
HDTV frequencies of 74.25 and 74.175824 MHz
On-chip patented VCXO with pull range of 200 ppm
(minimum)
Supports Ethernet with 20 and 25 MHz clocks
Modem clocks of 11.0592 and 24.576 MHz option
Audio clocks support 32 kHz, 44.1 kHz, 48 kHz and
96 kHz sampling rates
• Zero ppm synthesis error in all clocks (all exactly
track 27MHz VCXO)
•
•
•
•
•
Uses an inexpensive 13.5 MHz crystal
Full CMOS output swings with 12 mA output
drive capability at TTL levels
Advanced, low power, sub-micron CMOS process
3.3 V ±5% operating supply
Block Diagram
AS2:0
3
BS1, BS0
2
Audio Clock
PLL Clock
Synthesis
Circuitry
CS
BCLK
CCLK1
VIN
CCLK2
XI
13.5 MHz
pullable crystal
XO
Voltage
Controlled
Crystal
Oscillator
108 MHz or 27 MHz
X8
PLL
54 MHz or 27 MHz
Divide
Logic
VS
27 MHz
13.5 MHz or 27 MHz
1
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
Pin Assignment
B and C Clocks (MHz)
BS0
1
28
AS1
X2
2
27
AS0
X1
3
26
VDD
4
VDD
5
VIN
6
23
VCLK4
VDD
7
22
VDD
VDD
8
21
AS2
CS
9
20
GND
GND
10
19
BS1 BS0
CS
BCLK
CCLK1
CCLK2
0
0
0
74.175
20
25
VCLK2
0
0
1
74.175
11.0592
24.576
25
VCLK1
0
1
0
74.25
20
25
24
GND
0
1
1
74.25
11.0592
24.576
M
0
0
5.06
20
25
M
0
1
5.06
11.0592
24.576
M
1
0
10.12
20
25
GND
M
1
1
10.12
11.0592
24.576
GND
11
18
VCLK3
1
0
0
48
20
25
BCLK
12
17
CCLK1
1
0
M
48
7.3728
24
VS
13
16
BS1
ACLK
14
15
1
0
1
48
11.0592
24.576
CCLK2
1
1
0
14.318
20
25
1
1
M
14.318
7.3728
28.636
1
1
1
14.318
11.0592
24.576
Audio Clocks (MHz)
AS2
AS1
AS0
ACLK
0
0
0
8.192
0
0
1
11.2896
VS
VCLK1
VCLK2
VCLK3
VCLK4
0
1
0
12.288
0
27
27
27
108
0
1
1
16.9344
M
27
54
13.5
108
1
0
0
16.384
1
27
27
27
27
1
0
1
22.5792
1
1
0
18.432
1
1
1
24.576
2
MDS 3771-17 C
Integrated Circuit Systems, Inc.
VCXO Clocks (MHz)
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
BS0
I
2
X2
XO
Crystal connection. Connect to a pullable 13.5 MHz crystal.
3
X1
XI
Crystal connection. Connect to a pullable 13.5 MHz crystal.
4, 5, 7, 8, 22
VDD
P
Connect to +3.3 V.
6
VIN
I
Analog control voltage for VCXO. Pulls outputs ±100 ppm by varying from
0 to 3.3 V.
9
CS
TI
Communications Clock Select. Selects CCLK 1 and 2 per table above.
Internal pull-up.
10, 11, 19,
20, 24
GND
P
Connect to ground.
12
BCLK
O
B clock output. Determined by status of AS2:0 per table above.
13
VS
TI
VCXO Clock Select. Selects frequencies on VCLK1-VCLK4 per table
above.
14
ACLK
O
Audio Clock Output. Determined by status of AS2:0 per table above.
15
CCLK2
O
Communications Clock Output 2. Determined by status of CS per table
above.
16
BS1
TI
B Clock Select 1. Selects BCLK frequency. See table above.
17
CCLK1
O
Communications Clock Output 1. Determined by status of CS per table
above.
18
VCLK3
O
VCXO Clock output 3. Can be either 27 or 13.5 MHz per table above.
21
AS2
I
Audio Clock Select pin 2. Selects Audio clock on pin 14 per table above.
Internal pull-up.
23
VCLK4
O
VCXO Clock output 4. Can be either 27 or 108 MHz per table above.
25
VCLK1
O
VCXO Clock output 1. Always 27 MHz.
26
VCLK2
O
VCXO Clock output 2. Can be either 27 or 54 MHz per table above.
27
AS0
I
Audio Clock Select pin 0. Selects Audio clock on pin 14 per table above.
Internal pull-up.
28
AS1
I
Audio Clock Select pin 1. Selects Audio clock on pin 14 per table above.
Internal pull-up.
B clock select 0.
KEY:
I = Input
TI = Tri-level
O = Output
P = Power supply connection
XI, XO= Crystal connections
3
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
External Component Selection
Crystal Tuning Load Capacitors
The MK3771-17 requires a minimum number of
external components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01µF should be connected
between VDD and GND on pins 3 and 6, and on pins
13 and 14, as close to the MK3771-17 as possible. For
optimum device performance, the decoupling
capacitors should be mounted on the component side
of the PCB. Avoid the use of vias in the decoupling
circuit.
Series Termination Resistor
When the PCB traces between the clock outputs and
the loads are over 1 inch, series termination should be
used. To series terminate a 50Ω trace (a commonly
used trace impedance) place a 33Ω resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20Ω.
Quartz Crystal
The MK3771-17 VCXO function consists of the
external crystal and the integrated VCXO oscillator
circuit. To assure the best system performance
(frequency pull range) and reliability, a crystal device
with the recommended parameters must be used, and
the layout guidelines discussed in the following section
must be followed.
The frequency of oscillation of a quartz crystal is
determined by its “cut” and by the load capacitors
connected to it. The MK3771-17 incorporates on-chip
variable load capacitors that “pull” (change) the
frequency of the crystal. The crystal specified for use
with the MK3771-17 is designed to have zero
frequency error when the total of on-chip + stray
capacitance is 14 pF.
The external crystal must be connected as close to the
chip as possible and should be on the same side of the
PCB as the MK3771-17. There should be no vias
between the crystal pins and the X1 and X2 device
pins. There should be no signal traces underneath or
close to the crystal.
Please see application note MAN05 for recommended
crystal parameters and suppliers.
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors
on the PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture
and frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of
your final layout, a frequency counter capable of about
1 ppm resolution and accuracy, two power supplies,
and some samples of the crystals which you plan to
use in production, along with measured initial accuracy
for each crystal at the specified crystal load
capacitance, CL.
To determine the value of the crystal capacitors:
1. Connect VDD of the MK3771-17 to 3.3 V. Connect
pin 4 of the MK3771-17 to the second power supply.
Adjust the voltage on pin 4 to 0V. Measure and record
the frequency of the CLK output.
2. Adjust the voltage on pin 4 to 3.3 V. Measure and
record the frequency of the same output.
To calculate the centering error:
6 ( f 3.3V – f t arg et ) + ( f 0V – f t arg et )
Error = 10 x ------------------------------------------------------------------------------ – error xtal
f t arg et
Where:
ftarget = nominal crystal frequency
errorxtal =actual initial accuracy (in ppm) of the crystal
being measured
If the centering error is less than ±25 ppm, no
adjustment is needed. If the centering error is more
than 25ppm negative, the PC board has excessive
stray capacitance and a new PCB layout should be
considered to reduce stray capacitance. (Alternately,
the crystal may be re-specified to a higher load
capacitance. Contact ICS for details.) If the centering
error is more than 25ppm positive, add identical fixed
centering capacitors from each crystal pin to ground.
The value for each of these caps (in pF) is given by:
External Capacitor =
2 x (centering error)/(trim sensitivity)
4
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
Trim sensitivity is a parameter which can be supplied by
your crystal vendor. If you do not know the value,
assume it is 30 ppm/pF. After any changes, repeat the
measurement to verify that the remaining error is
acceptably low (typically less than ±25ppm).
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK3771-17. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
0 to +70°C
Storage Temperature
-65 to +150°C
Junction Temperature
125°C
Soldering Temperature
260°C
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature
0
Power Supply Voltage (measured in respect to GND)
+3.15
+3.3
Max.
Units
+70
°C
+3.45
V
5
MDS 3771-17 C
Integrated Circuit Systems, Inc.
Typ.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature 0 to +70°C
Parameter
Symbol
Conditions
Operating Voltage
VDD
Input High Voltage
VIH
Except TI pins
Input Low Voltage
VIL
Except TI pins
Input High Voltage
VIH
All TI pins
Input Low Voltage
VIL
All TI pins
Output High Voltage
VOH
IOH = -12 mA
Output Low Voltage
VOL
IOH = 12 mA
Output High Voltage
VOH
CMOS level,
IOH = -8 mA
Operating Supply Current
IDD
No load, Note 1
Min.
Typ.
Max.
Units
3.15
3.3
3.45
V
2
V
0.8
VDD-0.5
V
0.5
2.4
0.4
VDD-0.4
CIN
Frequency Synthesis
Error
28
mA
15
µA
±50
mA
5
pF
All clocks
VIN, VCXO Control
Voltage
V
V
Each output
Input Capacitance
V
V
Power Down Mode Supply
Current
Short Circuit Current
V
0
0
ppm
3.3
V
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature 0 to +70° C
Parameter
Symbol
Conditions
Min.
Typ.
Max.
13.50000
Units
Input Frequency
FIN
Output Clock Rise Time
tOR
0.8 V to 2.0 V
1.5
ns
Output Clock Fall Time
tOF
2.0 V to 0.8 V
1.5
ns
Output Clock Duty Cycle
tOD
At VDD/2
60
%
40
Maximum Absolute Jitter, short
term
VCXO Gain
VIN = VDD/2 ±1 V
Crystal Pullability
0V < VIN < 3.3 V,
Note 2
MHz
±250
ps
100
ppm/V
±100
ppm
Notes: 1. With all clocks at highest MHz.
2. With a pullable crystal that conforms to ICS’ specifications.
6
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
Thermal Characteristics
Parameter
Symbol
Thermal Resistance Junction to
Ambient
Thermal Resistance Junction to Case
Conditions
Min.
Typ.
Max. Units
θJA
Still air
100
°C/W
θJA
1 m/s air flow
80
°C/W
θJA
3 m/s air flow
67
°C/W
60
°C/W
θJC
Marking Diagram
28
ICS
15
######
YYWW
MK3771-17R
1
14
Marking Diagram (Pb free)
28
ICS
15
######
YYWW
MK3771-17RLF
1
14
Notes:
1. ###### is the lot code.
2. YYWW is the last two digits of the year, and the week number that the part was assembled.
3. “LF” designates Pb free packaging.
7
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com
MK3771-17
VCXO and HDTV Set-Top Clock Source
Package Outline and Package Dimensions (28-pin SSOP, 150 mil Body, 0.025 mm Pitch)
Package dimensions are kept current with JEDEC Publication No. 95, MO-153
28
Millimeters
Symbol
E1
A
A1
A2
b
C
D
E
E1
e
L
α
aaa
E
INDEX
AREA
1 2
D
A
2
Min
Inches
Max
Min
1.35
1.75
0.10
0.25
-1.50
0.20
0.30
0.18
0.25
9.80
10.00
5.80
6.20
3.80
4.00
0.635 Basic
0.40
1.27
0°
8°
-0.10
Max
.053
.069
.0040
.010
-.059
.008
.012
.007
.010
.386
.394
.228
.244
.150
.157
0.025 Basic
.016
.050
0°
8°
-0.004
A
A
1
c
-Ce
SEATING
PLANE
b
L
aaa C
Ordering Information
Part / Order Number
Marking
Shipping Packaging
Package
Temperature
MK3771-17R
MK3771-17R
Tubes
28-pin SSOP
0 to +70°C
MK3771-17RTR
MK3771-17R
Tape and Reel
28-pin SSOP
0 to +70°C
MK3771-17RLF
MK3771-17RLF
Tubes
28-pin SSOP
0 to +70°C
MK3771-17RLFTR
MK3771-17RLF
Tape and Reel
28-pin SSOP
0 to +70°C
“LF” denotes Pb (lead) free package.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
8
MDS 3771-17 C
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 083104
●
tel (408) 297-1201
●
www.icst.com