THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. HTTP://WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS CW 0503 FPHA554 155.52M SURFACE MOUNT 5.0V PECL CLOCK ABSOLUTE MAXIMUM RATINGS FPHA554 TABLE 1.0 PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS -40 - 85 °C -0.5 - 7.0 Vdc Storage Temperature Supply Voltage (Vcc) OPERATING SPECIFICATIONS NOTE DESCRIPTION The Connor-Winfield FPHA554 is a fixed frequency surface mount Crystal Controlled Oscillator (XO) designed for applications requiring low jitter and tight frequency stability. Operating at 5.0V supply voltage, the FPHA554 provides PECL Differential Outputs with an enable/disable function. TABLE 2.0 PARAME TER MINIMUM NOMINAL MAXIMUM UNITS NOTE 44.736 -15 0 - MHz ppm °C 1 - 200 15 70 (Vcc) 4.75 5.0 5.25 Vdc (Icc) - - 70 mA Jitter (BW=10Hz to 20MHz) - - 5 pS RMS Jitter (BW=12kHz to 20MHz) - - 1 pS RMS SSB Phase Noise at 10Hz offset - -60 - dBc/Hz SSB Phase Noise at 100Hz offset - -90 - dBc/Hz SSB Phase Noise at 1KHz offset - -100 - dBc/Hz SSB Phase Noise at 10KHz offset - -125 - dBc/Hz SSB Phase Noise at 10KHz offset - -135 - dBc/Hz MINIMUM NOMINAL MAXIMUM UNITS NOTE - - Vdc 2 3.40 Vdc 2 Center Frequency Total Frequency Tolerance Operating Temperature Range (Fo) Supply Voltage Supply Current INPUT CHARACTERISTICS TABLE 3.0 PARAMETER Disable Input Voltage (High) (Vih) 3.96 Enable Input Voltage (Low) (Vil) - PECL OUTPUT CHARACTERISTICS PARAMETER LOAD Voltage (High) (Low) Duty Cycle Rise / Fall Time 20% to 80% Package 5.0V OPERATION TABLE 4.0 (Voh) (Vol) PACKAGE CHARACTERISTICS FEATURES MINIMUM 3.96 45 - NOMINAL 50 - MAXIMUM 50 3.40 55 1 UNITS Ohms Vdc Vdc % nS LOW JITTER <1ps RMS NOTE 3 OVERALL FREQUENCY TOLERANCE: ±15ppm TEMPERATURE RANGE: 0 to 70°C 4 PECL DIFFERENTIAL OUTPUTS ENABLE / DISABLE TABLE 5.0 Non-hermetic package consisting of an FR4 subs trate with grounded metal cover. SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING PROCESS RECOMMENDATIONS Solder Reflow Wash TABLE 6.0 The component solder used internal to this device has a melting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Ultrasonic cleaning is not recommended. Notes 1) Includes initial tolerance, deviation over t emperature, supply and load variations, shock, vibrati on and 10 years aging. 2) When the oscillator is disabled, the true output is in a low state (Vol) and the complementary output is in the high s tate (VoH). 3) Output must be terminated into 50 ohms to Vcc – 2V or Thevenin equivalent. 4) Duty Cycle measured at 3.67V ORDERING INFORMATION FPHA554 - 155.52MHz ECL SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: EC213 PAGE 1 OF 2 REV: 00 DATE: 01/26/05 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. HTTP://WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS CW DATE CODE FPHA554 155.52M Pin 1 2 3 4 5 6 7 8 9 10 Connection N/C Enable / Disable N/C Ground N/C Q Output Q Output N/C Vcc N/C Dimensional Tolerance: ±.005 (.127mm) SUGGESTED PAD LAYOUT OUTPUT WAVEFORM “1” LEVEL “0” LEVEL ENABLE/ DISABLE Specifications subject to change without notice. DATA SHEET #: EC213 PAGE 2 OF 2 REV: 01 DATE: 01/26/05 aCopyright 2001 Connor-Winfield all rights reserved.