CY2SSTV855 Differential Clock Buffer/Driver Features Functional Description • Phase-locked loop (PLL) clock distribution for Double Data Rate Synchronous DRAM applications • 1:5 differential outputs • External feedback pins (FBINT, FBINC) are used to synchronize the outputs to the clock input • SSCG: Spread Aware™ for electromagnetic interference (EMI) reduction • 28-pin TSSOP package The CY2SSTV855 is a high-performance, very-low-skew, very-low-jitter zero-delay buffer that distributes a differential clock input pair (SSTL_2) to four differential (SSTL_2) pairs of clock outputs and one differential pair of feedback clock outputs. In support of low power requirements, when power-down is HIGH, the outputs switch in phase and frequency with the input clock. When power-down is LOW, all outputs are disabled to a high-impedance state and the PLL is shut down. The device supports a low-frequency power-down mode. When the input is < 20 MHz, the PLL is disabled and the outputs are put in the Hi-Z state. When the input frequency is > 20 MHz, the PLL and outputs are enabled. • Conforms to JEDEC DDR specifications When AVDD is tied to ground, the PLL is turned off and bypassed with the input reference clock gated to the outputs. The Cypress CY2SSTV855 is Spread Aware and supports tracking of Spread Spectrum clock inputs to reduce EMI Pin Configuration Block Diagram YT0 YC0 PWRDWN AVDD Powerdown and test logic YT2 YC2 CLKINT CLKINC FBINT FBINC PLL GND CLKINT CLKINC VDDQ AVDD AGND YT3 YC3 FBOUTT FBOUTC VDDQ YT1 YC1 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 CY2SSTV855 YT1 YC1 GND YC0 YT0 VDDQ GND YC3 YT3 VDDQ PWRDWN FBINT FBINC VDDQ FBOUTC FBOUTT VDDQ YT2 YC2 GND 28-pin TSSOP Rev 1.0, November 21, 2006 2200 Laurelwood Road, Santa Clara, CA 95054 Page 1 of 6 Tel:(408) 855-0555 Fax:(408) 855-0550 www.SpectraLinear.com CY2SSTV855 Pin Definition[1, 2] Pin Name I/O Description 6 CLKINT I True Clock Input. Low Voltage Differential True Clock Input. 7 CLKINC I Complementary Clock Input. Low Voltage Differential Complementary Clock Input. 22 FBINC I Feedback Complementary Clock Input. Differential Input Connect to FBOUTC for accessing the PLL. 23 FBINT I Feedback True Clock Input. Differential Input Connect to FBOUTT for accessing the PLL. 3,12,17,26 YT(0:3) O True Clock Outputs. Differential Outputs. 2,13,16,27 YC(0:3) O Complementary Clock Outputs. Differential Outputs. 19 FBOUTT O Feedback True Clock Output. Differential Outputs. Connect to FBINT for normal operation. A bypass delay capacitor at this output will control Input Reference/Output Clocks phase relationships. 20 FBOUTC O Feedback Complementary Clock Output. Differential Outputs. Connect to FBINC for normal operation. A bypass delay capacitor at this output will control Input Reference/Output Clocks phase relationships. 24 PWRDWN I Control input to turn device in the power-down mode. 4,8,11,18,21,25 VDDQ 2.5V Power Supply for Output Clock Buffers.2.5V Nominal. 9 AVDD 2.5V Power Supply for PLL. 2.5V Nominal. 1,5,14,15,28 GND Ground 10 AGND Analog Ground. 2.5V Analog Ground. Zero-delay Buffer When used as a zero-delay buffer the CY2SSTV855 will likely be in a nested clock tree application. For these applications the CY2SSTV855 offers a differential clock input pair as a PLL reference. The CY2SSTV855 then can lock onto the reference and translate with near zero delay to low-skew outputs. For normal operation, the external feedback differential input, FBINT/C, is connected to the feedback output, FBOUTT/C. By connecting the feedback output to the feedback input the propagation delay through the device is eliminated. The PLL works to align the output edge with the input reference edge thus producing a near zero delay. The reference frequency affects the static phase offset of the PLL and thus the relative delay between the inputs and outputs. When AVDD is strapped LOW, the PLL is turned off and bypassed for test purposes. Function Table Inputs Outputs AVDD PWRDWN CLKINT CLKINC YT(0:3) YC(0:3) FBOUTT FBOUTC PLL GND H L H L H L H BYPASSED/OFF GND H H L H L H L BYPASSED/OFF 2.5V H L H L H L H On 2.5V H H L H L H L On 2.5V X < 20 MHz < 20 MHz Hi-Z Hi-Z Hi-Z Hi-Z Off Notes: 1. PU = internal pull-up. 2. A bypass capacitor (0.1PF) should be placed as close as possible to each positive power pin (< 0.2”). If these bypass capacitors are not close to the pins their high frequency filtering characteristic will be cancelled by the lead inductance of the traces. Rev 1.0, November 21, 2006 Page 2 of 6 CY2SSTV855 Differential Parameter Measurement Information CLKINT CLKINC FBINT FBINC t() n+1 t()n t()n = n 6 1=N t()n N (is large number of samples) N Figure 1. Static Phase Offset CLKINT CLKINC FBINT FBINC t() td() td() td() t( ) td() Figure 2. Dynamic Phase Offset Y[0:3], FBOUTT YC[0:3], FBOUTC Y[0:3], FBOUTT YC[0:3], FBOUTC tsk(o) Figure 3. Output Skew Rev 1.0, November 21, 2006 Page 3 of 6 CY2SSTV855 Differential Parameter Measurement Information (continued) YT[0:3], FBOUTT YC[0:3], FBOUTC t(hper_N+1) t(hper_n) 1 f(o) tjit(hper) = thper(n) - 1 2x fo Figure 4. Half-period Jitter YT[0:3], FBOUTT YC[0:3], FBOUTC t c(n) t c(n) tjit(cc) = tc(n)-tc(n+1) Figure 5. Cycle-to-cycle Jitter VDD VDD V D D /2 16pF C LKT 60 O hm VTR R T = 120 O hm C LKC 60 O hm 16pF VCP R e c e iv e r V D D /2 Figure 6. Differential Signal Using Direct Termination Resistor Rev 1.0, November 21, 2006 Page 4 of 6 CY2SSTV855 Absolute Maximum Conditions[3] Storage Temperature: ................................ –65qC to + 150qC This device contains circuitry to protect the inputs against damage due to high static voltages or electric field; however, precautions should be taken to avoid application of any voltage higher than the maximum rated voltages to this circuit. For proper operation, Vin and Vout should be constrained to the range: Operating Temperature:................................ –40qC to +85qC VSS < (Vin or Vout) < VDD. Maximum Power Supply: ................................................ 3.5V Unused inputs must always be tied to an appropriate logic voltage level (either VSS or VDD). Input Voltage Relative to VSS:............................... VSS – 0.3V Input Voltage Relative to VDDQ or AVDD: ............. VDD + 0.3V DC Electrical Specifications (AVDD = VDDQ = 2.5V ± 5%, TA = –40°C to +85°C)[4] Parameter VID Description Conditions Differential Input Voltage[5] Voltage[6] Min. Typ. Max. Unit VDDQ + 0.6 V CLKINT, FBINT 0.36 CLKTIN, FBINT (VDDQ/2) – 0.2 VDDQ/2 (VDDQ/2) + 0.2 V VIX Differential Input Crossing IIN Input Current VIN = 0V or VIN = VDDQ, CLKINT, FBINT –10 – 10 µA IOL Output Low Current VDDQ = 2.375V, VOUT = 1.2V 26 35 – mA IOH Output High Current VDDQ = 2.375V, VOUT = 1V –18 –32 – mA – 0.6 V 1.7 – – V VOL Output Low Voltage VDDQ = 2.375V, IOL = 12 mA VOH Output High Voltage VDDQ = 2.375V, IOH = –12 mA VOUT Output Voltage Swing[7] 1.1 – VDDQ – 0.4 V VOC Output Crossing Voltage[8] (VDDQ/2) – 0.2 VDDQ/2 (VDDQ/2) + 0.2 V IOZ High-Impedance Output Current 10 µA Current[9] IDDQ Dynamic Supply IDD PLL Supply Current Cin Input Pin Capacitance VO = GND or VO = VDDQ –10 VDDQ = 170 MHz – 235 300 mA AVDD only – 9 12 mA – 4 – pF Typ. Max. Unit 60 170 MHz 40 60 % 100 µs 2 V/ns AC Electrical Specifications (AVDD = VDDQ = 2.5V±5%, TA = –40°C to +85°C)[10, 11] Parameter Description fCLK Operating Clock Frequency tDC Input Clock Duty Cycle[12] tLOCK Maximum PLL lock Time tSL(O) Output Clocks Slew Rate Conditions AVDD = 2.5V r 0.2V 20% to 80% of VOD Min. 1 tPZL, tPZH Output Enable Time (all outputs)[13] 30 ns tPLZ, tPHZ Output Disable Time (all outputs)[13] 10 ns tCCJ Cycle to Cycle Jitter f > 66 MHz –100 100 ps tJITT(H-PER) Half-period jitter f > 66 MHz –100 100 ps Notes: 3. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. 4. Unused inputs must be held HIGH or LOW to prevent them from floating. 5. Differential input signal voltage specifies the differential voltage |VTR – VCP| required for switching, where VTR is the true input level and VCP is the complementary input level. 6. Differential cross-point input voltage is expected to track VDDQ and is the voltage at which the differential signals must be crossing. 7. For load conditions see Figure 6. 8. The value of VOC is expected to be |VTR + VCP|/2. In case of each clock directly terminated by a 120: resistor. See Figure 6. 9. All outputs switching loaded with 16 pF in 60: environment. See Figure 6. 10. Parameters are guaranteed by design and characterization. Not 100% tested in production. 11. PLL is capable of meeting the specified parameters while supporting SSC synthesizers with modulation frequency between 30 kHz and 33.3 kHz with a downspread of –0.5% 12. While the pulse skew is almost constant over frequency, the duty cycle error increases at higher frequencies. This is due to the formula: duty cycle = tWH/tC, where the cycle time (tC) decreases as the frequency goes up. 13. Refers to transition of non-inverting output. 14. All differential input and output terminals are terminated with 120:/16 pF as shown in Figure 6. Rev 1.0, November 21, 2006 Page 5 of 6 CY2SSTV855 AC Electrical Specifications (AVDD = VDDQ = 2.5V±5%, TA = –40°C to +85°C)[10, 11] (continued) Parameter Description Conditions Min. Typ. Max. Unit tPLH Low-to-High Propagation Delay, CLKINT to YT[0:3] 1.5 3.5 6 ns tPHL High-to-Low Propagation Delay, CLKINT to YT[0:3] 1.5 3.5 6 ns tSK(0) Any Output to Any Output Skew[14] – – 100 ps –450 – 450 ps –350 – 350 ps [14] t(Ø) Static Phase Offset tD(Ø) Dynamic Phase Offset f > 66 MHz Ordering Information Part Number Package Type Product Flow CY2SSTV855ZC 28-pin TSSOP Commercial, 0q to 70qC CY2SSTV855ZCT 28-pin TSSOP – Tape and Reel Commercial, 0q to 70qC CY2SSTV855ZI 28-pin TSSOP Industrial, –40q to 85qC CY2SSTV855ZIT 28-pin TSSOP – Tape and Reel Industrial,–40q to 85qC 28-pin TSSOP Commercial, 0q to 70qC Lead Free CY2SSTV855ZXC CY2SSTV855ZXCT 28-pin TSSOP – Tape and Reel Commercial, 0q to 70qC CY2SSTV855ZXI 28-pin TSSOP Industrial, –40q to 85qC CY2SSTV855ZXIT 28-pin TSSOP – Tape and Reel Industrial,–40q to 85qC Package Drawing and Dimensions 28-Lead Thin Shrunk Small Outline Package (4.40-mm Body) Z28.173 DIMENSIONS IN MM[INCHES] MIN. MAX. PIN 1 ID 1 REFERENCE JEDEC MO-153 PACKAGE WEIGHT 0.16 gms 4.30[0.169] 4.50[0.177] 6.25[0.246] 6.50[0.256] PART # Z28.173 STANDARD PKG. ZZ28.173 LEAD FREE PKG. 28 0.65[0.025] BSC. 0.19[0.007] 0.30[0.012] 1.10[0.043] MAX. 0.25[0.010] BSC GAUGE PLANE 0°-8° 0.076[0.003] 0.85[0.033] 0.95[0.037] 9.60[0.378] 9.80[0.386] 0.05[0.002] 0.15[0.006] SEATING PLANE 0.50[0.020] 0.70[0.027] 0.09[[0.003] 0.20[0.008] While SLI has reviewed all information herein for accuracy and reliability, Spectra Linear Inc. assumes no responsibility for the use of any circuitry or for the infringement of any patents or other rights of third parties which would result from each use. This product is intended for use in normal commercial applications and is not warranted nor is it intended for use in life support, critical medical instruments, or any other application requiring extended temperature range, high reliability, or any other extraordinary environmental requirements unless pursuant to additional processing by Spectra Linear Inc., and expressed written agreement by Spectra Linear Inc. Spectra Linear Inc. reserves the right to change any circuitry or specification without notice. Rev 1.0, November 21, 2006 Page 6 of 6