100 WATT ASD SINGLE SERIES DC/DC CONVERTERS Features ● ● ● ● ● ● Description The 4:1 Input Voltage 100 W single ASD Series of DC/DC converters provide precisely regulated dc outputs. The output voltage is fully isolated from the input, allowing the output to be positive or negative polarity and with various ground connections. The ASD Series utilizes an insulated metal substrate design in an industry standard 1/2 brick case size to meet the most rigorous requirements of COTS and thermally challenging industrial applications. ● ● ● ● ● ● ● ● ● ● ● ● 4:1 Input voltage range High power density Small size 2.4” x 2.28” x 0.55” Excellent thermal performance with metal baseplate Volt-seconds clamp and fast over voltage protection Pulse-by-pulse current limiting, short circuit frequency foldback, dead short shut down Over-temperature protection Auto-softstart Low noise Industry-standard pinout Constant frequency during normal operation Remote sense Remote ON/OFF Super energy saving, 8 mA input idle current Output trim with very low temperature coefficient Water washable, wide humidity application Good shock and vibration damping Available in both RoHS and Non-RoHS construction. See ordering info below model selection chart. The 4:1 Input Voltage 100 Watt ASD Series includes remote sensing, output trim, and remote ON/OFF. Threaded-through holes are provided to allow easy mounting or add a heat sink for extended temperature use. Selection Chart Input Range VDC Iin ADC Min Max TYP ASD100-24S3.3W 9 36 ASD100-24S5W 9 36 ASD100-24S12W 9 ASD100-24S15W 9 ASD100-24S24W ASD100-48S3.3W ASD100-48S5W Vout VDC Iout ADC 4.24 3.3 25 4.91 5 20 36 4.85 12 8.33 36 4.79 15 6.67 9 36 4.79 24 4.13 18 75 2.10 3.3 25 18 75 2.42 5 20 ASD100-48S12W 18 75 2.39 12 8.33 ASD100-48S15W 18 75 2.37 15 6.67 ASD100-48S24W 18 75 2.37 24 4.13 Model Default ON/OFF logic is positive. Add -N to the model number to order negative On/Off logic. To order RoHS, add (RoHS) to part number. 375 Forbes Blvd. Mansfield, MA 02048 Ph: 800-823-8082 Fax: 508-339-0375 www.astrodyne.com Email: [email protected] 100 WATT ASD SINGLE SERIES DC/DC CONVERTERS Unless otherwise stated, these specifications apply for baseplate temperature TB=23±2ºC, nominal input voltage, and rated full load. (1) Input Parameters Model ASD100-24S3.3W ASD100-24S5W ASD100-24S12W ASD100-24S15W ASD100-24S24W Units Voltage Range MIN TYP MAX 9 24 36 V Input Overvoltage (100 ms) MAX 50 V Input Ripple Rejection (120Hz) TYP 60 dB Undervoltage Lockout Yes Input Reverse Voltage Protection Input Current No Load 100% Load Yes TYP TYP 35 4.24 35 4.91 35 4.85 35 4.79 35 4.79 mA A Inrush Current MAX 0.5 A2s Reflected Ripple, 12µH Source Impedance (3) TYP 30 mA P-P Efficiency TYP Switching Frequency TYP 79 85 86 Recommended Fuse 83 87 % 260 kHz (2) A Input Parameters Model ASD100-48S3.3W ASD100-48S5W ASD100-48S12W ASD100-48S15W ASD100-48S24W Units Voltage Range MIN TYP MAX 18 48 75 Input Overvoltage (100 mSec) MAX 80 V Input Ripple Rejection (120Hz) TYP 60 dB Undervoltage Lockout Yes Input Reverse Voltage Protection Yes Input Current No Load 100% Load TYP TYP 25 2.10 25 2.42 25 2.39 V 25 2.37 25 2.37 mA A Inrush Current MAX 0.5 A2s Reflected Ripple, 12µH Source Impedance (3) TYP 30 mA P-P Efficiency TYP Switching Frequency TYP 81 Recommended Fuse 85 88 88 89 % 260 kHz (2) A * Absolute Maximum Ratings. Caution: Stresses in excess of the Absolute Maximum Ratings can cause permanent damage to the device (see Note 1.) 375 Forbes Blvd. Mansfield, MA 02048 Ph: 800-823-8082 Fax: 508-339-0375 www.astrodyne.com Email: [email protected] 100 WATT ASD SINGLE SERIES DC/DC CONVERTERS Output Parameters Model ASD100-24S3.3W ASD100-48S3.3W ASD100-24S5W ASD100-48S5W 3.3 5 Output Voltage ASD100-24S12W ASD100-24S15W ASD100-24S24W ASD100-48S12W ASD100-48S15W ASD100-48S24W 12 15 24 Units V Output Voltage Setpoint Accuracy MAX Turn On Overshoot Min-Max Load TYP Temperature Coefficient TYP MAX 0.005 0.01 0.003 0.005 0.003 0.005 0.003 0.005 0.003 0.005 %/ºC Noise (8) TYP TYP 75 20 75 20 150 60 150 60 250 100 mV P-P mV RMS Load Current (4) MIN MAX 2.5 25 2 20 0.833 8.33 0.667 6.67 0.413 4.13 A Load Transient Overshoot (7) TYP 3 % Load Transient Recovery Time (6) TYP 200 µs Load Regulation (5) Min-Max Load TYP MAX 0.02 0.2 % Line Regulation Vin = Min-Max TYP MAX 0.01 0.1 % Overvoltage Protection (OVP) Threshhold OVP Type - Non-latching Open Loop Overvoltage Clamp MIN MAX 115 135 % Output Current Limit Vout = 90% of Vout-nom TYP 120 % Output Short Circuit Current Vout = 0.25V TYP MAX 140 150 % ±1 0 Notes: (1) Refer to the Application Notes for the definition of terms, measurement circuits, and other information. (2) Refer to the Application Notes for information of fusing. For inrush current, refer to the specifications above. (3) 33µF capacitor connected between the two “Input” pins. Then insert current sensor in series with 1.0µH inductor between 100µF and the source. The reflected ripple current is measured over a 5 Hz to 20 MHz bandwidth. (current sensor is located between the converter input pin and the 1.0 µH inductor) (4) Optimum performance is obtained when this power supply is operated within the minimum to maximum load specifications. No damage to the module will occur when the output is operated at less than minimum load, however, below minimum load the dynamic response will degrade. Operation below minimum load is not recommended. (5) Load regulation is defined as the output voltage change when changing load current from a maximum to minimum. (6) Load Transient Recovery Time is defined as the time for the output to settle from a 50% to 75% step load change to a 1% error band (rise time of step = 2µs). (7) Load Transient Overshoot is defined as the peak overshoot during a transient as defined in the Note 6 above. (8) Noise is measured per the Application Notes. Output noise is measured with a 10µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor connected across the output pins. Measurement bandwidth is 0-20MHz. (9) When an external ON/OFF switch is used, such as open collector switch, logic high requires the switch to be high-impedance. Switch leakage currents greater than 10µA may be sufficient to trigger the ON/OFF to the logic-low state. 375 Forbes Blvd. Mansfield, MA 02048 % Ph: 800-823-8082 % (10) Most switches would be suitable for the logic ON/OFF control. In case there is a problem you can make the following estimations and then leave some margin. When open collector is used for logic high, “Open Circuit Voltage at ON/OFF Pin”, “Output Resistance” and “External Leakage Current Allowed for Logic High” are used to estimate the high impedance requirement of open collector. When switch is used for logic low, “Open Circuit Voltage at ON/ OFF Pin”, “Output Resistance” and “LOW Logic Level” are used to estimate the low impedance requirement of the switch. (11) Thermal impedance is tested with the converter mounted vertically and facing another printed circuit board 1/2 inch away. If converter is mounted horizontally with no obstruction, thermal impedance is approximately 8°C/W. (12) Water Washability - These DC/DC converters are designed to withstand most solder/wash processes. Careful attention should be used when assessing the applicability in your specific manufacturing process. Converters are not hermetically sealed. (13) Torque fasteners into threaded mounting inserts at 12 in.lbs. or less. Greater torque may result in damage to unit and void the warranty. (14) Input impedance on these units needs to be kept to a minimum. The 9-36Vdc DC units need a maximum input impedance of 0.2 Ohms and the 18-75Vdc DC units need a maximum input impedance of 0.8 Ohms. In order to support this requirement, the 9-36Vdc DC units need 25 µF of capacitance (low ESR) for every 1.0 µH of inductance between the power source and the DC/DC converter. The 18-75Vdc DC units need 1.7µF of capacitance (low ESR) for every 1.0 µH of inductance between the power source and the DC/DC converter. Inductance includes all sources and should take into account input power lines. (15) RoHS Compliance: See Astrodyne Website www.astrodyne.com for the complete RoHS Compliance statement and Application Notes. The RoHS marking is as follows. Fax: 508-339-0375 www.astrodyne.com Email: [email protected] 100 WATT ASD SINGLE SERIES DC/DC CONVERTERS General Specifications All Models Units ON/OFF Function HIGH Logic Level or Leave ON/OFF Pin Open MIN 3.0 VDC General Specifications All Models Units General Unit Weight TYP External Leakage Current Allowed for Logic High (9) MAX 10 µA Input Diode Protection Voltage MAX 50 VDC Agency Approvals LOW Logic Level or Tie ON/OFF Pin to -INPUT MAX 1.0 VDC UL, TUV Sinking Current for Logic Low MAX 500 µA Open Circuit Voltage at ON/OFF Pin (10) Positive Logic Negative Logic TYP TYP 2.3 1.5 VDC VDC Output Resistance TYP 3 kΩ Idle Current (Module is OFF) TYP 8 mADC Turn-on Time to 1% error TYP 60 ms Positive Logic Option HIGH - Module ON LOW - Module OFF Negative Logic Option HIGH - Module OFF LOW - Module ON 4.6/114 Case Dimension oz/g 2.4” x 2.28” x 0.55” Torque on Mounting Inserts MAX 12 in. lbs. Pending for UL60950 EN60950 (TUV) Chassis Mounting Kit MS21 Output Voltage Remote Sensing Maximum Voltage Drops on Leads MAX 10 % Line Regulation under remote sensing TYP MAX 0.02 0.1 % Load Regulation under remote sensing TYP MAX 0.05 0.2 % MIN MAX -10 +10 % of Vout TOLERANCE: ALL DIMENSIONS ARE TYPICAL IN INCHES UNLESS OTHERWISE NOTED: Output Voltage Trim Trim Range Input Resistance TYP 10 kΩ Open Circuit Voltage TYP 2.5 V MAX 110 % of Vout Trim Limit Maximum Output Voltage Isolation ±0.020 X.XXX ±0.005 Pin Name Pin Dia. Pin Dia. 1 -INPUT 0.08” 0.04” 2 CASE 0.04” 0.04” 3 ON/OFF 0.04” 0.04” VDC VDC 4 +INPUT 0.08” 0.04” 5 -OUTPUT 0.08” 0.08” 10 MΩ 6 -SENSE 0.04” 0.04” 1600 pF 7 TRIM 0.04” 0.04” 8 + SENSE 0.04” 0.04” 9 + OUTPUT 0.08” 0.08” Input to Output Isolation 10µA Leakage Vnom = 24V Vnom = 48V MAX MAX 700 1544 Input to Output Resistance MIN Input to Output Capacitance TYP Environmental Calculated MTBF, Bellcore Method 1, Case 1 X.XX >1,000,000 h Baseplate Operating Temperature Range MIN MAX -40 100 ºC Storage Temperature MIN MAX -40 120 ºC Thermal Impedance (11) TYP 7 ºC/W Thermal Shutdown Baseplate Temperature (Auto Restart) MIN TYP 100 110 ºC 375 Forbes Blvd. Mansfield, MA 02048 Ph: 800-823-8082 Fax: 508-339-0375 www.astrodyne.com Email: [email protected]