NJW1161 P R E L I M I N ALY AUDIO PROCESSOR with SRS 3D STEREO ■ GENERAL DESCRIPTION The NJW1161 is an audio processor that includes SRS 3D stereo. It includes all of the audio signal processing functions for TV such as tone control, balance, volume, mute, and AGC. The SRS 3D stereo technology reproduces a 3D stereo surround sound effect using only two speakers. 2 All of internal status and variables are controlled by I C BUS interface. ■ PACKAGE OUTLINE NJW1161L NJW1161M ■ FEATURES Operating Voltage 7.5 to 13V 2 I C BUS Interface AGC Circuit (It reduces volume difference among input sources.) SRS 3D Stereo Simulated Surround Bi-CMOS Technology Package Outline SDIP30, SDMP30 ■ BLOCK DIAGRAM VOL1 TONE VOL2 I2C Bus Interface SRS 3D Stereo & Simulated Surround AGC VOL1 TONE VOL2 Bias - 1 - NJW1161 ■ PIN FUNCTION No. Symbol 1 IN1a 2 NC 1 INa INb 30 2 NC NC 29 3 NC NC 28 4 OUT1a OUT1b 27 5 IN2a IN2b 26 6 TONE-Ha TONE-Hb 25 7 TONE-La TONE-Lb 24 8 OUT2a OUT2b 23 9 AGC SRS-FIL2 22 VREF 21 10 SRS/SS-FIL1 11 CVB CTH 20 12 CVA CTL 19 13 SDA AUX0 18 14 SCL AUX1 17 15 GND Vcc 16 Function No Symbol Function Ach Input 16 Vcc Power Supply Pin Non Connect 17 AUX1 Auxiliary Output1 3 NC Non Connect 18 AUX0 4 OUT1a Ach Output for the Other Accessories 19 CTL DAC Output for Tone Low Frequency 5 IN2a Ach Input From the Other Accessories 20 CTH DAC Output for Tone High Frequency 6 TONE-Ha Ach Treble Filter 21 VREF 7 TONE-La Ach Bass Filter 22 SRS-FIL2 8 OUT2a Ach Output 23 OUT2b 9 AGC 10 SRS/SS-FIL1 11 CVB Reference Voltage SRS Surround Filter2 Bch Output AGC Filter 24 TONE-Lb Bch Bass Filter SRS and Simulated Stereo Filter1 25 TONE-Hb Bch Treble Filter DAC Output for Bch Volume & Balance 26 IN2b Bch Input from the Other Accessories Bch Output for the Other Accessories 12 CVA DAC Output for Ach Volume & Balance 27 OUT1b 13 SDA SDA Data Input (I2C BUS) 28 NC 2 14 SCL SCL Data Input (I C BUS) 29 NC 15 GND GND 30 IN1b -2- Auxiliary Output0 Non Connect Non Connect Bch Input NJW1161 ■ ABSOLUTE MAXIMUM RATING (Ta=25°C) PARAMETER SYMBOL + RATING UNIT Supply Voltage V 14 V Power Dissipation PD 700 mW Operating Temperature Range Topr -20 to +75 °C Storage Temperature Range Tstg -40 to +125 °C ■ ELECTRICAL CHARACTERISTICS ( Ta=25°C, V+=9V, Rg=600Ω, RL=47kΩ, Vin=100mVrms/1kHz unless otherwise specified) PARAMETER SYMBOL TEST CONDITION + MIN. TYP. MAX. UNIT 7.5 9.0 13.0 V Operating Voltage V Supply Current ICC No Signal - 10 25 mA VREF No Signal 4.0 4.5 5.0 V 2.8 3.0 - Vrms - 2.5 - Vrms Reference Voltage Maximum Input Voltage VIM VOL=-20dB,THD=10% Maximum Output Voltage VOM OUTPUT VOL=0dB,THD=1% Channel Balance GCB VOL=0dB -1.5 0.0 1.5 dB Balance Boost A BABST CHS=”0”,BAL=”11111” -2.0 0.0 2.0 dB Balance Cut A BACUT CHS=”1”,BAL=”11111” Vin = 1Vrms - - -70 dB Balance Boost B BBBST CHS=”1”,BAL=”11111” -2.0 0.0 2.0 dB Balance Cut B BBCUT - - -70 dB - - 0.5 % -2.0 0.0 2.0 dB Total Harmonic Distortion THD CHS=”0”,BAL=”11111” Vin = 1Vrms Vo=0.5Vrms BW=400Hz to 30kHz Maximum Gain GVMAX VOL= 0dB Minimum Gain GVMIN VOL= MUTE - - -70 dB CS Vin = 2Vrms - - -70 dB VOL = 0dB A-weighted VOL = MUTE A-weighted - -90 (31.6) -106 (5.0) Logic Output : High 4.5 - 5.0 Logic Output : Low 0 - 0.3 Channel Separation Output Noise 1 VNO1 Output Noise 2 VNO2 AUX Output Voltage VAUX -85 (56.2) -96 (15.8) dBV (µVrms) dBV (µVrms) V BW : Band Width -3- NJW1161 ♦ TONE CONTROL PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT High Frequency Boost HFBST BCT=”1”,TREB=”1111”, f=10kHz 12.5 15.0 17.5 dB High Frequency Flat HFFLT TRBE=”0000”,f=10kHz -2.0 0.0 2.0 dB High Frequency Cut HFCUT -17.5 -15.0 -12.5 dB Low Frequency Boost LFBST 12.5 15.0 17.5 dB Low Frequency Flat LFFLT BASS=”0000”,f=100Hz -2.0 0.0 2.0 dB LFCUT BCB=”0”,BASS=”1111”, f=100Hz -17.5 -15.0 -12.5 dB MIN. TYP. MAX. UNIT Low Frequency Cut BCT=”0”,TRBE=”1111”, f=10kHz BCB=”1”,BASS=”1111”, f=100Hz ♦ AGC CONTROL(AGC-ON) PARAMETER SYMBOL TEST CONDITION AGC Boost AGCBST Vin=50mVrms, f=1kHz 1.5 3.5 5.5 dB AGC Flat1 AGCFLT1 Vin=150mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat2 AGCFLT2 Vin=300mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat3 AGCFLT3 Vin=400mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Flat4 AGCFLT4 Vin=540mVrms, f=1kHz -2.5 0.0 2.5 dB AGC Cut AGCCUT Vin=2Vrms, f=1kHz -14 -10 -6.0 dB MIN. TYP. MAX. UNIT ♦ SIMULATED SURROUND PARAMETER (Simulated Surround-ON, f=1kHz) SYMBOL TEST CONDITION SURROUND SIM A SRSIMA Ain+Bin → Aout 1.0 3.0 5.0 dB SURROUND SIM B SRSIMB Ain+Bin → Bout 1.0 3.0 5.0 dB MIN. TYP. MAX. UNIT ♦ SRS 3D-Stereo (SRS 3D Stereo-ON, f=125Hz) PARAMETER SYMBOL TEST CONDITION SRS GAIN HIGH 1 SRSGH1 Ain → Aout, Mode=High 10.0 12.0 14.0 dB SRS GAIN HIGH 2 SRSGH2 Bin → Bout, Mode=High 10.0 12.0 14.0 dB SRS GAIN LOW 1 SRSGL1 Ain → Aout, Mode=Low 7.0 9.0 11.0 dB SRS GAIN LOW 2 SRSGL2 Bin → Bout, Mode=Low 7.0 9.0 11.0 dB SRS GAIN HIGH 3 SRSGH3 Bin → Aout, Mode=High 6.8 8.8 10.8 dB SRS GAIN HIGH 4 SRSGH4 Ain → Bout, Mode=High 6.8 8.8 10.8 dB -4- NJW1161 2 ■ I C BUS BLOCK CHARACTERISTICS (SDA,SCL) PARAMETER SYMBOL MIN. TYP. MAX. UNIT High Level Input Voltage VIH 3.0 - 5.0 V Low Level Input Voltage VIL 0 - 1.5 V High Level Input Current IIH - - 10 µA Low Level Input Current IIL - - 10 µA Low Level Output Voltage (3mA at SDA pin) VOL 0 - 0.4 V Maximum Output Current IOL -3.0 - - mA Maximum Clock Frequency fSCL - - 100 kHz Data Change Minimum Waiting Time tBUF 4.7 - - µs tHD:STA 4.0 - - µs Low Level Clock Pulse Width tLOW 4.7 - - µs High Level Clock Pulse Width tHIGH 4.0 - - µs Minimum Start Preparation Waiting Time tSU:STA 4.7 - - µs Minimum Data Hold Time tHD:DAT 5.0 - - µs Minimum Data Preparation Time tSU:DAT 250 - - ns Rise Time tR - - 1.0 µs Fall Time tF - - 300 ns tSU:STO 4.0 - - µs Data Transfer Start Minimum Waiting Time Minimum Stop Preparation Waiting Time 2 I C BUS Load Condition: Pull up resistance 4kΩ (Connected to +5V) Load capacitance 200pF (Connected to GND) SDA tBUF tR tF tHD:STA SCL tHD:STA tLOW P S tHD:DAT tHIGH tSU:STA tSU:DAT Sr tSU:STO P -5- NJW1161 TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 1,30 pin 1 30 INa INb 20k Ach Input terminal Bch Input terminal V+/2 80k Vref 4 8 23 27 OUT1a OUT2a OUT2b OUT1b Ach Output for the Other Accessories Ach Output Bch Output Bch Output for the Other Accessories 50 V+/2 FB 22.2k 10 SRS/SS-FIL1 SRS and Simulated Stereo Filter1 FB 6 25 TONE-Ha TONE-Hb Treble (tone control) filter terminal FB -6- 4, 8 23,27pin 10pin V+/2 20k 6, 25pin V+/2 NJW1161 TERMINAL DESCRIPTION No. SYMBOL FUNCTION 7 24 TONE-La TONE-Lb Bass (tone control) filter terminal 9 AGC Capacitor connection terminal for AGC attack and recovery time setting 11 12 CVB CVA Pop Noise Reduction for Volume & Balance EQUIVALENT CIRCUIT 12k VOLTAGE 7, 24pin V+/2 12k FB 9pin 400 - 4k 400 11,12pin 8k - 5V 13 SDA 13pin 4k 2 I C data terminal - 8k 5V 14 SCL 2 I C clock terminal 14pin 4k - 8k -7- NJW1161 TERMINAL DESCRIPTION No. SYMBOL FUNCTION 5 26 IN2a IN2b Ach Input from the Other Accessories Bch Input from the Other Accessories EQUIVALENT CIRCUIT 5,26pin 24k VOLTAGE V+/2 212k 21 Vref V+/2 Reference voltage terminal 21pin 212k 5V 17 18 AUX0 AUX1 Auxiliary 2 values voltage output terminal 20 19 CTH CTL Pop Noise reduction for Bass Control Pop Noise reduction for Treble Control 22 SRS-FIL2 SRS Surround Filter2 15 16 V+ GND Ground terminal Supply voltage terminal -8- V+ 0/5V 50 19pin FB 17, 18pin 36k 3k - - 22pin V+/2 - NJW1161 ■ APPLICATION CIRCUIT 4.7µ 4.7µ 4.7µ 4.7µ 4.7n 1 IN1a 2 IN1b 30 NC NC 29 3 NC NC 28 4 OUT1a OUT1b 27 5 IN2a IN2b 26 4.7µ 4.7µ 6 TONE-Ha TONE-Hb 25 4.7n 7 TONE-La TONE-Lb 24 100n 8 OUT2a OUT2b 23 1µ 9 AGC SRS-FIL2 22 22n 10 SRS/SS-FIL1 VREF 21 4.7µ 11 CVB CTH 20 4.7µ 4.7µ 12 CVA CTL 19 4.7µ 13 SDA AUX0 18 14 SCL AUX1 17 15 GND Vcc 16 100n 330nF 4.7µ 4.7µ 4.7K 8.2n 4.7µ 22µ (NOTE) 2 1. Separate the I C bus line from the following terminals for avoiding digital noise problem. Pin No. Symbol Pin No. Symbol Pin No. Symbol 6 TONE-Ha 10 SRS/SS-FIL1 24 TONE-Lb 7 TONE-La 22 SRS-FIL2 25 TONE-Hb 2. The constant of capacitors connected to the terminals No.10 and 22 are designated by SRS Labs. Do not change the constant of these capacitors without the approval of SRS Labs. -9- NJW1161 ■ APPLICATION NOTE 1. AGC (Auto Gain Control) Circuit AGC circuit adjusts the input signal level with Boost/Attenuate circuit. AGC boost the low input signal level and attenuate high input signal level automatically. 2 The AGC flat levels (150mV, 300mV, 400mV and 540mV) are selectable via I C bus. (Refer to the following figure.) AGC Control V+=9V, Vin(Ach+Bch), f=1kHz, Vo(Ach)OUTPUT Rg=600Ω, Ta=25oC 540mV Output Voltage [Vrms] 1 400mV 0.1 AGC ON 300mV 150mV 0.01 0.001 0.001 AGC OFF 0.01 0.1 1 Input Voltage [Vrms] Attack-Recovery Rb=8kΩ Ra=4kΩ 9pin Ir=0.5µA 11pin 12pin Cb Ca Smoothing circuit of Attenuate Smoothing circuit of Boost Attack and recovery time in the attenuation processing depends on external part Ca, and it in the boost processing depends on external part Cb. They become longer as the capacity bigger and become shorter as it gets smaller. (Recommendation value: Ca=1µF, Cb=4.7µF) Reducing the capacity of Ca may cause the distortion. As for Cb, since it serves as the click noise prevention, reducing the capacity may cause the click noise upon volume changing. - 10 - NJW1161 2. Tone Control a) Bass: Setting the Cut-off frequency Bass Filter 12k fC = 12k 8pin 23pin M 2π × C ×12k M changes by gain setting of Tone. M ≈ 2.65 M ≈ 3.45 M ≈ 8.10 C (±15dB) (±10dB) (±5dB) b) Treble: Setting the Cut-off frequency Treble Filter fC = N 2π × C ×10k N changes by gain setting of Tone. 10k C 7pin 24pin N ≈ 0.76 N ≈ 0.58 N ≈ 0.25 (±15dB) (±10dB) (±5dB) 3. AUX1, AUX0 Terminal AUX1/0 are enable to control external logic circuit is Source current : 1mA typ. (Ta=25˚C) Sink current : 0.5mA typ. (Ta=25˚C) 4. Capacitor for Reference Voltage (21pin) 22µF should be recommended for ripple filter connected to Vref terminal (21pin). Reducing this capacity may cause to reduce the maximum attenuation level and to increase the output noise. - 11 - NJW1161 2 ■ DEFINITION OF I C REGISTER 2 ♦ I C BUS FORMAT MSB S LSB Slave Address 1bit 8bit MSB LSB A Select Address 1bit 8bit MSB A 1bit LSB Data A P 8bit 1bit 1bit S: Starting Term A: Acknowledge Bit P: Ending Term ♦ SLAVE ADDRESS MSB LSB 1 0 0 0 0 0 1 R/W R/W=0: Receive Only R/W=1: No Output Data ♦ CONTROL REGISTER TABLE The select address sets each function (Volume, Balance, AGC, Surround, Tone Control, AUX). The auto increment function cycles the select address as follows. 00H→01H→02H→03H→04H→05H→00H Select Address BIT D7 D6 D5 D4 00H D3 D2 D1 D0 AGC SUR VOL 01H CHS 02H BCB BASS BCSB Don’t care Don’t care 03H BCT TREB BCST Don’t care Don’t care 0 0 AUX1 AUX0 (✴) 04H 05H BAL 0 0 0 0 0 0 OUT Don’t care Don’t care SUR0 AGC1 AGC0 (✴) Please send the data only “0” ♦ CONTROL REGISTER DEFAULT VALUE Control register default value is all “0”. Select Address - 12 - BIT D7 D6 D5 D4 D3 D2 D1 D0 00H 0 0 0 0 0 0 0 0 01H 0 0 0 0 0 0 0 0 02H 0 0 0 0 0 0 0 0 03H 0 0 0 0 0 0 0 0 04H 0 0 0 0 0 0 0 0 05H 0 0 0 0 0 0 0 0 NJW1161 INSTRUCTION CODE a) MASTER VOLUME SETTING Select Address BIT D7 D6 D4 D5 00H D3 D2 D1 D0 VOL The volume control for both Ach and Bch(0.33dB/step). The volume is consisted of volume1 and volume2 and the level is divided into half to each volume1 and volume2. b) BALANCE, AGC AND SURROUND SETTING BIT Select Address D7 01H CHS D6 D4 D5 D3 D2 BAL D1 D0 AGC SUR •CHS : Channel select for balance control “0” : Ach “Bch is attenuated” “1” : Bch “Ach is attenuated” •BAL : Balance control for both Ach and Bch(1dB/Step) The balance is consisted of volume1 and volume2 and the level is divided into half to each volume1 and volume2. •AGC : AGC switch “0” : AGC OFF “1” : AGC ON (Default Setting : 150mVrms) •SUR : Surround mode switch “0” : Surround OFF “1” : Surround ON(Default Setting : Surround Effect1) c)TONE CONTROL BASS SETTING BIT Select Address D7 02H BCB D6 D4 D5 BASS D3 D2 D1 D0 BCSB Don’t Care Don’t Care •BCB : Boost cut select for Bass control “0” : Cut “1” : Boost •BASS: BASS control Cut Level : -15dB to 0dB(1dB/Step) Boost Level : 0dB to +15dB(1dB/Step) •BCSB : Boost cut select for SUB-BASS control “0” : Cut “1” : Boost - 13 - NJW1161 d) TONE CONTROL TREBLE SETTING BIT Select Address D7 03H BCT D6 D4 D5 D3 TREB D2 D1 D0 BCST Don’t Care Don’t Care •BCT : Boost cut select for Treble control “0” : Cut “1” : Boost •TREB: Treble control(1dB/step) Cut Level : -15dB to 0dB(1dB/Step) Boost Level : 0dB to +15dB(1dB/Step) •BCST : Boost cut select for Sub-Treble control “0” : Cut “1” : Boost e)OUTPUT AND AUXILIARY SETTING BIT Select Address D7 D6 D5 D4 D3 D2 D1 D0 05H OUT Don’t Care Don’t Care SUR0 AGC1 AGC0 AUX1 AUX0 •OUT: ON/OFF Switch for OUTPUT “0” : OFF “1” : ON •Surround Setting Surround Function SUR0(05H:D4) SUR(01H:D0), Surround OFF 0 0 Surround Effect1 0 1 Surround Effect2 1 1 Simulated Stereo 1 0 •AGC Level Setting AGC Level AGC1(D3) AGC0(D2) 150mVrms 0 0 300mVrms 0 1 400mVrms 1 0 540mVrms 1 1 •AUX1/AUX0: Auxiliary port High/Low “0” : Logic output ”Low” “1” : Logic output ”High” - 14 - Remarks Surround OFF SRS 3D-Stereo – Low Mode SRS 3D-Stereo – High Mode Monaural to Stereo NJW1161 MASTER VOLUME (Select Address : 00H) VOL Gain(dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 -41 -42 FF FC F9 F6 F3 F0 ED EA E7 E4 E1 DE DB D8 D5 D2 CF CC C9 C6 C3 C0 BD BA B7 B4 B1 AE AB A8 A5 A2 9F 9C 99 96 93 90 8D 8A 87 84 81 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 - 15 - NJW1161 MASTER VOLUME (Select Address : 00H) VOL Gain(dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 -56 -57 -58 -59 -60 -61 -62 -63 -64 -65 -66 -67 -68 -69 -70 -71 -72 -73 -74 -75 -76 -77 -78 -79 -80 -81 -82 -83 -84 Mute 7E 7B 78 75 72 6F 6C 69 66 63 60 5D 5A 57 54 51 4E 4B 48 45 42 3F 3C 39 36 33 30 2D 2A 27 24 21 1E 1B 18 15 12 0F 0C 09 06 03 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 - 16 - NJW1161 BALANCE(Select Address : 01H) Channel Select (CHS) D7 Ach(Bch is attenuated) 0 Bch(Ach is attenuated) 1 BAL Gain(dB) D6 D5 D4 D3 D2 0 0 0 0 0 0 -1 0 0 0 0 1 -2 0 0 0 1 0 -3 0 0 0 1 1 -4 0 0 1 0 0 -5 0 0 1 0 1 -6 0 0 1 1 0 -7 0 0 1 1 1 -8 0 1 0 0 0 -9 0 1 0 0 1 -10 0 1 0 1 0 -11 0 1 0 1 1 -12 0 1 1 0 0 -13 0 1 1 0 1 -14 0 1 1 1 0 -15 0 1 1 1 1 -16 1 0 0 0 0 -17 1 0 0 0 1 -18 1 0 0 1 0 -19 1 0 0 1 1 -20 1 0 1 0 0 -21 1 0 1 0 1 -22 1 0 1 1 0 -23 1 0 1 1 1 -24 1 1 0 0 0 -25 1 1 0 0 1 -26 1 1 0 1 0 -27 1 1 0 1 1 -28 1 1 1 0 0 -29 1 1 1 0 1 -30 1 1 1 1 0 Mute 1 1 1 1 1 - 17 - NJW1161 TONE CONTROL BASS (Select Address : 02H) Bass Cut or Boost BCB D7 Cut 0 Boost 1 BASS Cut Gain(dB) Boost Gain(dB) D6 D5 D4 D3 -15 15 1 1 1 1 -14 14 1 1 1 0 -13 13 1 1 0 1 -12 12 1 1 0 0 -11 11 1 0 1 1 -10 10 1 0 1 0 -9 9 1 0 0 1 -8 8 1 0 0 0 -7 7 0 1 1 1 -6 6 0 1 1 0 -5 5 0 1 0 1 -4 4 0 1 0 0 -3 3 0 0 1 1 -2 2 0 0 1 0 -1 1 0 0 0 1 0 0 0 0 0 0 - 18 - NJW1161 TONE CONTROL TREBLE (Select Address : 03H) Treble Cut or Boost BCT D7 Cut 0 Boost 1 TREB Cut Gain(dB) Boost Gain(dB) D6 D5 D4 D3 -15 15 1 1 1 1 -14 14 1 1 1 0 -13 13 1 1 0 1 -12 12 1 1 0 0 -11 11 1 0 1 1 -10 10 1 0 1 0 -9 9 1 0 0 1 -8 8 1 0 0 0 -7 7 0 1 1 1 -6 6 0 1 1 0 -5 5 0 1 0 1 -4 4 0 1 0 0 -3 3 0 0 1 1 -2 2 0 0 1 0 -1 1 0 0 0 1 0 0 0 0 0 0 - 19 - NJW1161 TYPICAL CHARACTERISTICS Supply Current vs Temperature Supply Current vs Supply Voltage V+=9V o Ta=25 C 15 Supply Current [mA] Supply Current [mA] 16 10 5 0 14 12 10 8 0 5 10 0 15 100 o Temperature [ C] Supply Voltage [V] Gain vs Volume Control Gain vs Balance Control V+=9V, Vin(Ach)=1Vrms,f=1kHz, V+=9V, Vin=1Vrms, f=1kHz, Rg=600Ω OUTPUT,Rg=600Ω, Ta=25oC 0 50 0 -20 -40 -60 o 75,25,-20 C Gain [dB] Gain [dB] -20 -80 -100 -40 Vo(Bch) 75, 25, -30oC Vo(Ach) 75, 25, -20oC -60 -80 0 -10 -20 -30 -40 -50 -60 -70 -80 MUTE -100 MUTE -30 -30 Volume Control [dB] 00 10 -10 20 -20 30-30 Balance Control [dB] Output Noise vs Volume Control Output Noise vs Temperature V+=9V, OUTPUT,A-Weighted V+=9V, Rg=600Ω, A-Weighted Rg=600Ω, Ta=25oC -60 -20 -20 -10 -10 -40 Output Noise [dBV] -70 Gain [dB] -80 -90 -100 -60 Vol=0dB -80 Vol=MUTE -100 -110 -120 0 -10 -20 -30 -40 -50 -60 -70 -80 MUTE Volume Control [dB] - 20 - -120 0 50 Temperature [oC] 100 MUTE NJW1161 TYPICAL CHARACTERISTICS THD+N vs Input Voltage THD+N vs Input Voltage V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT o Rg=600Ω, BW=400Hz-30kHz, Ta=25 C 100 100 10 -30dB THD+N [ % ] THD+N [ % ] 10 1 0.1 V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600Ω BW=400Hz-30kHz, Vol=-20dB 1 0.1 -20dB -10dB 0.01 0.01 75oC 0dB 0.1 0.01 0.01 1 Input Voltage [Vrms] V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600Ω, BW =400Hz-30kHz, Vol=0dB BW=400Hz-30kHz, Rg=600Ω, Ta=25oC 100 10 10 THD+N [ % ] THD+N [ % ] -30dB 1 0.1 -20dB -10dB 25oC 0.1 75oC 0dB 0.01 0.01 1 V+=9V, Vin=2Vrms, f=1kHz, Vo=OUTPUT o Vo(Ach)OUTPUT, Rg=600Ω, Ta=25 C 100 Channel Separation [Hz] 100 80 60 40 20 1000 Frequency [Hz] 1 Channel Separation vs Frequency Gain vs Frequency (MUTE) V+=9V, Vin(Ach)=1Vrms, Vol=MUTE 100 0.1 Output Voltage [Vrms] Output Voltage [Vrms] Gain [dB] -20oC 1 0.1 0.01 0.01 0 1 THD+N vs Output Voltage V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT 120 0.1 Input Voltage [Vrms] THD+N vs Output Voltage 100 25oC -20oC 10 4 Rg=600Ω, Vol=0dB, Ta=25oC 80 60 Vin(Ach)-Vo(Bch) Vin(Bch)-Vo(Ach) 40 20 0 100 1000 10 4 Freqency [Hz] - 21 - NJW1161 TYPICAL CHARACTERISTICS Gain vs Frequency (TONE) Gain vs Frequency (TONE) V+=9V, Vin(Ach)=0.1Vrms,Gv= +-15dB V+=9V, Vin(Ach)=0.1Vrms,Gv:3dB steps Vo(Ach), Rg=600Ω, Ta=25oC 20 20 C(7,24pin) = 47nF, 100nF, 220nF, 470nF 100nF 10 Gain [dB] 10 Gain [dB] Vo(Ach), Rg=600Ω, Ta=25oC 0 470nF 0 220nF 47nF -10 -10 -20 100 1000 10 -20 4 100 10 4 Frequency [Hz] Frequency [Hz] AGC Control Gain vs Frequency (TONE) 20 1000 V+=9V, Vin(Ach)=0.1Vrms,Gv= +-15dB V+=9V, Vin(Ach+Bch), f=1kHz, Vo(Ach)OUTPUT Vo(Ach), Rg=600Ω, Ta=25oC Rg=600Ω, Ta=25oC C(6,25pin) = 1nF, 2.2nF, 4.7nF, 10nF 540mV Output Voltage [Vrms] 1 10 2.2nF Gain [dB] 10nF 0 1nF -10 4.7nF -20 100 1000 10 400mV 300mV 0.1 150mV 0.01 OFF 0.001 0.001 4 Frequency [Hz] 0.01 0.1 1 Input Voltage [Vrms] AGC Attack Time (C:9pin=1 µF) AGC Recovery Time (C:9pin=1 µF) V+=9V, Vin(Ach+Bch)=1Vrms, f=10kHz,Vo(Ach)OUTPUT AGC level=0.15V,Rg=600Ω,Ta=25oC 2 AGC level=0.15V,Rg=600Ω,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT 0 -1 -2 0 -0.1 -0.2 0 2 4 6 Time [ms] - 22 - 0.1 8 10 0 100 200 300 Time [ms] 400 500 NJW1161 TYPICAL CHARACTERISTICS AGC Recovery Time (C:9pin=2.2 µF) V+=9V, Vin(Ach+Bch)=1 to 0.05Vrms, f=10kHz, AGC level=0.15V,Rg=600Ω,Ta=25oC 2 Vo(Ach)OUTPUT,AGC level=0.15V,Rg=600Ω,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] AGC Attack Time (C:9pin=2.2 µF) V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT 0 -1 -2 0 2 4 6 8 0.1 0 -0.1 -0.2 10 0 100 AGC Attack Time (C:9pin=0.47 µF) 300 400 500 AGC Recovery Time (C:9pin=0.47 µF) V+=9V, Vin(Ach+Bch)=1Vrms,f=20kHz,Vo(Ach)OUTPUT V+=9V, Vin(Ach+Bch)=1 to 0.05Vrms, f=10kHz, AGC level=0.15V,Rg=600Ω,Ta=25oC 2 Vo(Ach)OUTPUT,AGC level=0.15V,Rg=600Ω,Ta=25oC 0.2 1 Output Voltage [V] Output Voltage [V] 200 Time [ms] Time [ms] 0 -1 -2 0 2 4 6 Time [ms] 8 10 0.1 0 -0.1 -0.2 0 100 200 300 400 500 Time [ms] - 23 - NJW1161 TYPICAL CHARACTERISTICS Phase vs Frequency (Simulated) Gain vs Frequency (SRS&Simulated) V+=9V, Vin(A+Bch)=0.1Vrms, Rg=600Ω, V+=9V, Vin=0.1Vrms,OUTPUT, Rg=600ohm, Ta=25oC 200 20 Simulated (A+B)IN-AOUT 0 SRS:Low AIN-BOUT -10 -20 100 1000 Frequency [Hz] - 24 - BchOUT 150 SRS:Low AIN-AOUT Phase [deg] Gain [dB] 10 Ta=25oC 100 50 AchOUT 0 -50 10 4 -100 100 1000 Frequency [Hz] 10 4 NJW1161 ■NOTE 1)The SRS technology right incorporated in the NJW1161 is owned by SRS Labs, a U.S. Corporation and licensed to New Japan Radio Co., Ltd. SRS is protected under U.S. and foreign patents issued and/or pending. , are trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and the Neither the purchase of the NJW1161, nor the corresponding sale of audio enhancement equipment conveys the right to sell commercialized recording made with any SRS technology. SRS Labs requires that all users of the NJW1161 must enter into a license agreement directly with SRS Labs if the royalty is not included in the purchase price. SRS Labs also requires any users to comply with all rules and regulations as outlined in the SRS Trademark Usage Manual. For further information, please contact: SRS Labs, Inc. 2909 Daimler Street, Santa Ana, CA 92705 USA Tel : (949)442-1070 Fax: : (949)852-1099 www.srslabs.com 2 2)Purchase of I C components of New Japan Radio Co., Ltd or one of its sublicensed Associated Companies 2 2 conveys a license under the Philips I C Patent Rights to use these components in an I C system, provided that 2 the system conforms to the I C Standard Specification as defined by Philips. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 25 -